Need Help with Packet Loss and routing Loop perhaps???

Hi,
I am running into a very odd situation. One of our highly critical systems (172.18.1.2/16) is losing connection intermittently for brief periods of time (1minute, 3 minute, 50 seconds and so on).
I have gathered some information that I would like to share with you guys:
The switch is a 3560 (Show version is in ShowVersion.txt)
default gateway is 172.18.10.254/16 (virtual IP in an HSRP , packet capture is done on the active node)
I have noticed that pings to one of the default gateways drop infrequently (more frequently from machines on 172.18.0.0/16) segment.
total number of machines on 172.18.0.0/16 do not exceed 200
I have captured packets on Interface Vlan1 and I found something very weird, perhaps pointing to a routing loop??? (see capture.png) The ICMP request comes and hits the 172.18.10.254 with TTL of 128 TWICE! then packet capture shows that same packet with TTL decremented by one TWICE! again and again until it reaches TTL of 1 and then it responds with a reply.
At times it completely ignores the requests and causes a request timed out.
I am confused and need help in right direction. I really appreciate it.
can you also confirm if the multiple packets mean routing loop somewhere?
Thanks

Could you post a copy of your HRSP config and the results of a #show standby?
Thanks

Similar Messages

Need help with Blog, Wiki and Gallery

Hi Team,
Need help with Blog, Wiki and Gallery startup. I have newly started visiting forums and quite interested to contribute towards these areas also.
Please help.
Thanks,
Santosh Singh
Santosh Singh

Hello Santhosh,
Blog is for Microsoft employees only. However, you can contribute towards WIKI and GALLERY using the below links.
http://social.technet.microsoft.com/wiki/
http://gallery.technet.microsoft.com/

Need help with Airport Express and so on.

Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.

DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection.

Need help with Page Layout and Background Scaling

hello, everyone.
I am in the process of designing a new website for myself,
and while I was researching nicely designed pages to use as
inspiration, I stumbled upon this site:
http://www.jeffsarmiento.com/
obviously, the design is very impressive, but it also
incorporates a lot of web mechanics that I have been trying to
figure out, so I will use this page as an example.
one thing I need help with is backgrounds. as you can see in
the posted website, the creator used a seamlessly tiled paper
texture to display the bulk of his content on. also make not of the
pattern that is located to the left of the paper texture. how do I
create seamless backgrounds like this that will scale to fit any
amount of content or any resolution? I can't imagine that the guy
that made that site created a new size background every time he
made an update, so there has to be an easier way.
the second thing that I am having trouble with is general
site layout. I have read that most sites used series of invisible
tables to organize there content, but when I open the source of
this page in dreamweaver, he was using something different. div
tags? should I be using these? who do I use them? are there any
general layout tips that someone could pass on to me? perhaps a
link to a good tutorial?
please help me. i am very confused.
thanks so much.

IMO not a good site to emulate. To wit:
Top background image:
http://www.jeffsarmiento.com/images/bg-top.jpg;
745px
x 350px 137K
Main background image:
http://www.jeffsarmiento.com/images/bg-tile.jpg;
745px x 950px 130K
Total page size: 454K (Check here:
www.websiteoptimization.com)
Website usability experts routinely recommend a maximum page
size of ~80K
Check out the We We Scale @ www.FutureNowInc.com/wewe/ where
they suggest,
"You speak about yourself approximately 0,003 times as often
as you speak
about your customers. Might that have an impact on your
effectiveness?"
That is 100% consistent with the #1 Web Design mistake:
"Believing people
care about you and your web site." or to phrase more
expansively, "Our site
tries to tell you how wonderful we are as a company, but not
how we're going
to solve your problems."
www.sitepoint.com has some excellent books on making a
website actually
attractive and usable at the same time.
Walt
"beWILLdered_" <[email protected]> wrote in
message
news:[email protected]...
> hello, everyone.
> I am in the process of designing a new website for
myself, and while I was
> researching nicely designed pages to use as inspiration,
I stumbled upon
> this
> site:
>
http://www.jeffsarmiento.com/
> obviously, the design is very impressive, but it also
incorporates a lot
> of
> web mechanics that I have been trying to figure out, so
I will use this
> page as
> an example.
> one thing I need help with is backgrounds. as you can
see in the posted
> website, the creator used a seamlessly tiled paper
texture to display the
> bulk
> of his content on. also make not of the pattern that is
located to the
> left of
> the paper texture. how do I create seamless backgrounds
like this that
> will
> scale to fit any amount of content or any resolution? I
can't imagine that
> the
> guy that made that site created a new size background
every time he made
> an
> update, so there has to be an easier way.
> the second thing that I am having trouble with is
general site layout. I
> have
> read that most sites used series of invisible tables to
organize there
> content,
> but when I open the source of this page in dreamweaver,
he was using
> something
> different. div tags? should I be using these? who do I
use them? are there
> any
> general layout tips that someone could pass on to me?
perhaps a link to a
> good
> tutorial?
> please help me. i am very confused.
>
> thanks so much.
>

Need help with saving data and keeping table history for one BP

Hi all
I need help with this one ,
Scenario:
When adding a new vendor on the system the vendor is suppose to have a tax clearance certificate and it has an expiry date, so after the certificate has expired a new one is submitted by the vendor.
So i need to know how to have SBO fullfil this requirement ?
Hope it's clear .
Thanks
Bongani

Hi
I don't have a problem with the query that I know I've got to write , the problem is saving the tax clearance certificate and along side it , its the expiry date.
I'm using South African localization.
Thanks

Need help with show/hide and layers moving

I'm more of a designer, so I don't know code or CSS well at
all. I'm doing an online portfolio for a class and need help with
layers not staying in place in different browsers. The portfolio is
created with a table, but I wanted to use the show/hide function
for thumbnails of work. Are layers the only way you can use this
function? I read layers don't work well with tables, so how else
can I make it so when you mouse over a thumbnail, the larger image
appears in another cell?

> I don't know code or CSS well at all.
That's unfortunate.
> layers not staying in place in different browsers.
Layers don't move. But the rest of your page does.
Before you get too wrapped up in layers, though, please read
this -
http://www.great-web-sights.com/g_layerlaws.asp
They are not good when be used as a primary layout method.
> I read layers don't work well with tables
They work fine with tables - but you have to understand both
tables and
layers to use them.
Why not show us your page, so we can see what you are
struggling with?
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"Bobbi67" <[email protected]> wrote in
message
news:ertd9h$h3m$[email protected]..
> I'm more of a designer, so I don't know code or CSS well
at all. I'm doing
> an
> online portfolio for a class and need help with layers
not staying in
> place in
> different browsers. The portfolio is created with a
table, but I wanted to
> use
> the show/hide function for thumbnails of work. Are
layers the only way you
> can
> use this function? I read layers don't work well with
tables, so how else
> can I
> make it so when you mouse over a thumbnail, the larger
image appears in
> another
> cell?
>

FCP Novice needs help with video quality and FCP 5!!

Hi,
I have a real problme that I cannot seem to fix. I think its because I am doing something really wrong!
I have a Sony HC42E MiniDV Camcorder which by default records video in full widescreen. I recorded several tapes this way and have now begun trying to edit them in FCP 5.04 (Tiger 10.4.6). Whenever I log and capture my clips they appear to be fuzzzy and unclear on the Mac monitor whilst being totally crisp and sharp on the camcorder viewfinder. I tried capturing using the DV PAL 48Khz Anamorphic Preset which keeps everything the right size (the final output needs to be true widescreen and not with black bars added) but the resulting video on screen is blurry and bitty. I then tried capturing using the DV PAL 720 x 576 normal preset and the video is a little clearer on the screen (for both presets I have chosen lower field dominance) but when I play back it plays back in widescreen on the mac canvas window but at 4:3 on the camera's viewfinder.
I then assumed that maybe this is just becuase the mac screen (CRT by the way) doesn't use fields. So I exported the sequence as a QT movie using DV PAL 16:9 and used quicktime (OS9 Classic - my compressor has never worked because of the dreaded "unable to connect to baackground process" problem which I've never managed to correct) to convert it to MPEG2. When I import this as an asset into DVD Studio pro 4 and set the track size to 16:9 it comes through at the right aspect ratio. However it looks blurry on screen. Thinking that this will be fine on a TV I burned the disc - inserted it into my DVD player (a good one!) and watched it on my new 32" widescreen TV (a good one!) and the picture qualitty is poor. Its so much blurrier and bittier than the original footage looks when played through the camcorder's viewfinder!
The final footaage looks like an old VHS recording that's a year or two old!
Does anyone know how I can capture my footage in FCP with the maximum quality, edit it without quality loss and the export it for DVD again without such significant quality loss whilst all the time keeping it at proper 16:9 widescreen?
Is there some presets I should be working to?
I'm tearing my hair out! Help!

Hi Guys,
thanx for your replies.
here's the latest:
Brian, I followed your instructions and the DVD burned successfully. However the video quality of the dvd when viewed on my TV ('ve tried on all 3 of my tvs now) is still a lot poorer than the quicktime movie that was imported into DVDSP4. When I play the original QT Movie on my Mac CRT monitor it looks a little blurry and grainy because I guess its non interlaced however when viewed on an external Video monitor it looks great - very sharp.
When I view the burned DVD on my television the picture quality looks like the non interlaced version of the original QT Movie that appeared on my Mac CRT and not the sharp interlaced (lower field) version that appeared on my external video monitor.
Its almost like taking a sharp jpeg into Photoshop and applying a gaussian blur of about 0.3 followed by jepg compression compressing it down to 5% quality!
I'm totally mystified. Can the conversion to Mpeg2 be removing all interlacing so that you get the less sharp computer monitor look? I just want the video on my final DVDs to be as good as the original source footage! I appreciate that along the way there might be loss of some quality but surely not that much?
Does this make sense to you guys or am I still doing something very wrong?
Robert: I have tried setting all manner of drives including a fresh external firewire HD with nothing on it (clean out of the box) but it doesn't seem to help.
Brian: I tried the no network suggestion a few months back but I'm not sure if I got it right. At the moment I have broadband through an external speedtouch usb modem and am also connected (occasionally although not for the last 3 months) via a crossover cable to my PCs ethernet card. When I last tried the No Network solution I had immense trouble getting my internet to work again! Can you please help me by directing me to the best ay to do this while protecting my internet settings?
any more help guys would be greatfully appreciated.

Need help with load balancing and DNS proxy

Hi,
I need help on how to configure my router so it will work with my DNS proxy and load balancing.
I have a Linksys LRT224 router. I have two broadband connections from two separate ISPs,500Mbps each (WAN1 & WAN2). WAN1 has a static IP and WAN2 is dynamic assigned. I use Unlocator (www.unlocator.com) so I can access geographically restricted sites (Pandora, Netflix, etc.).
The problem I have is that unlocator registers only one IP address (WAN1 address) and since I am doing load balancing I have no way of knowing if the DNS request will go through the registered IP (WAN1) or through the other (WAN2). I am not an expert in routing or networking but I'm guessing I have a way of configuring the router so all the DNS requests go out through WAN1, right?
In the router's Dual WAN config page there is a section for Protocol Binding. I tried to configure but only managed to screw up the internet at home. I used:
DNS[UDP/53-53]->192.168.1.1-192.168.1.254(0.0.0.0-0.0.0.0)WAN2
Any help or suggestions are appreciated.
Alex

Good solution though. That's probably the only way you could do true Load Balancing anyway.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Need help with load balancing and DNS proxy -Repost

Hi,
I need help on how to configure my router so it will work with my DNS proxy and load balancing.
I have a Linksys LRT224 router. I have two broadband connections from two separate ISPs,500Mbps each (WAN1 & WAN2). WAN1 has a static IP and WAN2 is dynamic assigned. I use Unlocator (www.unlocator.com) so I can access geographically restricted sites (Pandora, Netflix, etc.).
The problem I have is that unlocator registers only one IP address (WAN1 address) and since I am doing load balancing I have no way of knowing if the DNS request will go through the registered IP (WAN1) or through the other (WAN2). I am not an expert in routing or networking but I'm guessing I have a way of configuring the router so all the DNS requests go out through WAN1, right?
In the router's Dual WAN config page there is a section for Protocol Binding. I tried to configure but only managed to screw up the internet at home. I used:
DNS[UDP/53-53]->192.168.1.1-192.168.1.254(0.0.0.0-0.0.0.0)WAN2
Any help or suggestions are appreciated.
Alex

Good solution though. That's probably the only way you could do true Load Balancing anyway.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Need help with Boot Camp and Win 7

I have iMac 27" (iMac11,1) 2.8 GHz, quad core, 8MB of L3, 8GB of Memory, Boot ROM Version IM111.0034.B02 and SMC Version 1.54f36 and can't get this machine to run Windows 7 using Boot Camp. I have successfully loaded Win 7 but when it claims to be starting I only get a black screen after initial start up.
I have checked and rechecked my software updates and have read and reread the instructions, however, I can't update my Boot Camp to 3.1 (my machine says i'm running 3.0.4) and I need 3.1 but can't load 3.1 because it is an exe file that has to be loaded into Windows after I load Windows but can't open Windows because I can't load Boot Camp 3.1. That's my excuse anyway, so I'm missing something I just can't figure out what it is....this is where you come in!
Thanks.
Mike

Mike,
I'm not going to be much help with Boot Camp however I can direct you to the Boot Camp forum where there are more people that know how to troubleshoot it and Windoze 7. You can find it at:
https://discussions.apple.com/community/windows_software/boot_camp
Roger

Need help with my E2100L Wireless Router

I moved back home with the parents after graduating from college while I'm searching for a job and I noticed my parent's wireless internet connection was really poor. I'm normally pretty decent with computers but I haven’t been able to fix this problem so I am hoping if I explain it to you fine folks and can point me in the right direction to getting everything running properly.
The problem I’m having is with the wireless signal fluctuating frequently when I’m not in the same room with the router. I know the issue is not with Comcast or the modem because when I remove the router and just plug into the modem I get 25 Mbps all day long when I run a test on Speedtest.net.
The setup is Comcast Internet 25 Mbps, SB6120 Modem, and Linksys E2100L Wireless Router with WPA2/WPA security activated.
Before I touched anything the modem and router were originally in my parent’s bedroom. I was getting speeds of less than 1 Mbps if any when I was in my bedroom so I moved them into the living room to be more centrally located. Our house is a one story house with bedrooms divided by the living room. The move seemed to help a little but something was still really wrong so I did a hard reset on the router. I setup up the network manually by going through the settings on 192.168.1.1. which made things work a little better. However I still wasn’t getting close to the speeds I should have been getting and when in my bedroom the connection would sometimes drop out altogether. So I did another hard reset on the router and this time I used the CD that came with it (Cisco Connect) to setup the network. That has got my problem halfway fixed because now if I am in the living room and my laptop is connected wirelessly when I run the speed test I get 25 Mbps.
I thought I have solved everything because in my bedroom the signal was now very good at 20 Mbps… except the 20 Mbps didn’t last. It held around 20 Mbps for the about first 10 minutes but then dropped to about 16 Mbps for a while. A day later when I run the test I now range anywhere from 3 Mbps to 14 Mbps. There seems to be no consistency. I did a hard reset again and setup the network using the CD and the problem persists. I get 20 Mbps in the very beginning and then it lowers from there and fluctuates frequently.
I thought it might be a firmware issue so I successfully updated it today to the latest firmware “1.0.05 build 4 Mar 8, 2012” but the same thing happens. I just don’t get it. Why am I able to get 20 Mbps for the first few min in my bedroom and then it’s a crapshoot thereafter? If it were interference wouldn’t the interference always be there and not be a gradual onset? Why when I’m in the living room with the router is it perfect at 25 Mbps but as soon as I go to my bedroom I get a much much lower connection speed.
I could handle the speed being lower if it was consistent but it’s not. This post has taken me about 20 min to type and while doing so I ran the test a few times at a couple minutes apart and got 3 Mbps, 7 Mbps, and 10 Mbps speeds. Someone please help! This is driving me crazy!!!

When in my bedroom there are only 2 other networks available to join that belong to neighbors but their signal strength is fair at best while my signal dances between being excellent and good. There is no microwave oven, cordless phone, or garage between me and the router. When I'm in my bedroom I'm no more than 10 feet from the actual router and only seperated by a wall and I'm pretty sure its not a brick wall.
Again I don't understand how it could be interference. If there was something interfering wouldn't it always be interfering? Like I said in my first post every time I reset the network I get speeds of 20 Mbps for the first few min in my bedroom and then it gradually lowers and I get a fluctuating speed between 3 and 14 Mbps.
In the settings there is no channel width option of 40 MHz only. I get "20 MHz only" and "Auto(20MHz or 40MHz)" as my options. I have tried them both but don't really notice a difference.
I am going to try the insider program today to see what its results are.

Need help with Apps misbehaving and upgrading the MacOS: The all-in-one post. ;)

Hi there,
So, I've been browsing the SL and Mavericks forums for the last days but although I have fetched some useful tips and answers, still need some help. Let me put it diary-style so I can be more concise ;)
Here's my current system profile:
iMac 27" (aluminium back- if I'm no wrong, from around late 2009-mid 2010)
MacOS 10.6.1 Never updated.
3.06 Ghz Intel Core2 Duo
4Gb RAM
LaCie Big Disk via FireWire 800
Internet access via Ethernet port (cable)
And here's The Issues Log:
– Day one: First ever Kernel Panic. Restart. Nothing (apparently) wrong.
– 3 weeks elapsed: Second Kernel Panic. Same. iMac restarts fine. Apps fine. No missing files. No misbehaviour experiences.
– After a month or so: One morning, Skype decides on its own to stop launching. The night before, I chatted with one of my clients, fine as always, but at the next day, nothing. Computer is usually shut off for the night. And so it was that night. Updated Skype and also did all the guest account trick / repaired permissions / repair ACLs. Nothing worked. Overwrote the Skype app with a former functioning version I have in an MacOS 10.5 system. Didn't work. Now I have to chat on the MacOS 10.5 computer. No good.
– 15 days ago or so: After realising that I no longer have my HP1515n printer (it ran out of inks and thrashed it. It costs more to refill than to buy a new one), I deleted the printer from the printers list in the System Prefs Pane.
– Last week: Acrobat (CS4) won't launch a PDF file and freezes. Spinning beach ball. Force quit and try opening the PDF file again. Freezes again. And again. And again. With that file and every other PDF.
Photoshop CS5 fails to open or crashes when attempting to open any jpg or tiff file. InDesign and Illustrator CS5 are frozen and had to force quit both. MacOS 10.5
Restart the iMac thinking it is just a "common" bad day and hoping everything will be alright after the restart, but nope.
Not only the CS5 stops working; MSOffice stops working too. Spinning beach ball. Begin to suspect of the deletion of the printer, however, I also deleted the same printer in the above mentioned 10.5 system and I'm not experiencing anything strange. Reinstalled the HP drivers but nothing remarkable happens.
Then, try to uninstall CS5, CS4, Office, etc. Try to reinstall Acrobat CS4 and the CS5 apps. Reinstall Office. Nothing. Just Outlook works.
Since I had to desperately meet deadlines, convinced a colleague to come over to the studio and -I know, I know- allowed me to install a copy of CS6. It seems to work fine, except for Acrobat, which randomly freezes/hangs/works and Photoshop, which works fine unless you want to open a layered file containing text layers or if you want to type text on a normal file, because it freezes as soon as the Text Tool is pressed in the toolbar, of course, spinning beach ball again.
Well, Illustrator CS6 sometimes shows a strange black thin frame overlaid on the interface but goes away by switching to another workspace and then back to the current. InDesign CS6 seems to be fine and making PDFs as expected. However, as I said before, it is pure luck if Acrobat accepts to open the file or even if it launches. Spinning beach ball when freezing/hanging.
As a method for eliminating possible culprits, did a clean up of the Suitcase Fusion database, removed duplicate and a few (less than 10) corrupted fonts.
Removed completely MSOffice reinstalled and updated. Nothing. Now I neither have MSoffice running.
I am no rookie but I can't even imagine what can cause such amount of misbehaviour, (kernel panics have something to do? malware? lack of system updates? MacHD is damaged?) so I'm thinking of a few scenarios:
Backing up my projects and user folder –anything else to backup? (In fact I've already done that)– and:
1. Do a clean install. Not sure if it will be best to completely erase the whole drive or if a standard reinstallation will be enough.
2. Take the machine to a Genius Bar to see if there's anything that can be done without major OS messes.
3. Erase the drive and go through the Mavericks upgrading (SL to Ln to MLn to Mavcks), although not sure if this upgrade is worth yet.
4. Replace HD for a brand new one and either step 1 or 3.
5. As a complement, I'm thinking of adding more RAM.
Well. It is really the first time I don't know what to do. I have work to do and would not want to face a week away from my main computer and since most of the files are CS5-6 and hence, can't move to my wife's iMac...
Apologies if this post feels too long, but I will truly appreciate any kind of input and advice on one of more of the issues mentioned in this post.
And if it fits best in any other forum, please also let me know.
Cheers and thanks in advantage.

You have to use the Base Station Menu on the Menu Bar at the very top of your screen.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Deperately need help with my iPod and Pioneer Car Stereo

I just bought Pioneer's newest deck from Best Buy. The Model number of the deck is DEH-P6800MP. It has a mini jack (2.5 mm stereo jack) on the front of the deck that you can plug your iPod into. I purchased the little adaptor that allows me to just plug the iPod in using the Headphone Jack. It works great. I can use my click wheel to navigate the menus and the sound is awesome...except for one thing, it only plays through the right side speakers. I thought maybe the Fader needed to be adjusted on the deck but everything is dead center. I thought maybe something was wrong with the deck but the Tuner and CD player both work perfectly. I even tried using different cables with no success. When I called Best Buy they told me they were familiar with the problem and to download the newest software for my iPod and it should fix it. It didn't! I am so frustrated by this. I paid alot of money for this deck thinking I wouldn't have to buy any additional interfaces and would never have to deal with an FM transmitter again. Can anybody help?
Fifth Generation 60 Gig iPod Windows XP

After plugging my walkman in and experiencing the same problem, I figured it must be the adaptor. I went to the local Radio Shack and picked up a mini-jack adaptor that was indeed Stereo. Thankfully it worked!!! I can't tell you how happy my family and I are to have all our music available in the family vehicle. Thanks for your help and @#$% Best Buy for selling me not one but two car stereos under the false pretense that I wouldn't need anything else to hook-up my iPod and then not having any idea how to help me when I needed it.
Windows XP

Need help with hearing Skype and Steam chats at th...

When im using skype and using steam (a gaming app) i cant hear my skype friends through my headphones and i need help
Subject/title expanded from "Help."

Hi, Natasharocks11, and welcome to the Community,
I could not detect from your post precisely what the problem with your account is. Please kindly post back with details as well as any error messages you may be seeing.
Thank you,
Elaine
Was your question answered? Please click on the Accept as a Solution link so everyone can quickly find what works! Like a post or want to say, "Thank You" - ?? Click on the Kudos button!
Trustworthy information: Brian Krebs: 3 Basic Rules for Online Safety and Consumer Reports: Guide to Internet Security Online Safety Tip: Change your passwords often!

Need help with n95-3 and PTT

Hello, I bought an unlocked N95-3 and I have AT&T USA. Does anyone know if your able to use the PTT program with AT&T and if so how? I assume you have to take your phone in or something to get it installed if its even possible. Any help would be greatly appreciated and i apologize if this is a repost but I couldnt find anything for the -3

you'll need to preload the images if you want them to appear
close-to-immediately after your button press.
to load them with the button press:

Need Help with Packet Loss and routing Loop perhaps???

Similar Messages

Maybe you are looking for