Need help with port forwarding an Avtech DVR

For some reason I can't get my Avtech DVR to work on my android phone on Avtech's Eagle Eyes app.
The camera/dvr comes up on wifi, but not on 4g. I am trying to get the port forwarding to work, but its not working. It says the ip address is not accesible.
The port for the dvr is 80. This is what I have. I thought it was correct?
I have a Westell 9100EM router.
Solved!
Go to Solution.

Thought I'd post an update to this. I fixed it. I had to change ports on my dvr.

Similar Messages

Need help with my Pioneer dvd-rw dvr-115d. HLEP!!

Hello i need help with my G4, i havent been useing it for a while and i started using it again. As i was trying to burn a DVD it didnt read my cd at all even if i put a DVD in there it dont read it just come right back out.. on my mac it shows that is there but not reading . what can i do????!!! i need help with this..
PIONEER DVD-RW DVR-115D:
Firmware Revision:          1.18
Interconnect:          ATAPI
Burn Support:          Yes (Vendor Supported Drive)
Profile Path:          /Library/DiscRecording/DeviceProfiles/PatchBurn-pioneerdvdrwdvr115d.drprof ile
Cache:          2000 KB
Reads DVD:          Yes
CD-Write:          -R, -RW
DVD-Write:          -R, -R DL, -RW, +R, +R DL, +RW
Write Strategies:          CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media:          Insert media and refresh to show available burn speeds
this is what it say in the system profiler.
Power PC Mac os x 10.5.8

The new user account didn't work?
Or, the firmware flash didn't work?
I would try reconnecting the data ribbon. It is cramped and difficult to get to, but it may be some corrosion or a poor connection causing the issue.
It's worth a try, as the DVR-115 is a good drive. They don't make them any more........
You can find an optical drive installation video (on the following page) to help you with your efforts:
http://eshop.macsales.com/installvideos/

Urgent help with Port Forwarding?

Hi all!
I hope my posting in the right section.
Basically I have a DVR in my home. I want to be able to view the 1 camera that I have externally (from a different home)
I have managed to be able to view the camera internally on my network (the dvr is plugged into the BT HUB 3)
I did this by Advanced Settings>Port Forwarding>Supported Apps>
I was told by the Manifacturer of the DVR that the ports i needed to forward are 8234 to 8239
Does this look correct to you guys?
The DVR i have a is a Digital Sprite 2 PLUS. Ive turned the firewall off on the router settings as I thought that could be the problem. I can view the dvr internally as I said above using the DVR i.p 192.168.1.69 perfectly, but when I type in my external i.p via my other home it wont connect at all.
Could anybody help me as to what im doing wrong?
Thanks for any replys !
James.

You are replying to an old posting.
The information on this link may help you.
Port forwarding problems
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Help with port forwarding to application

Help needed to Port Forward on to my PS3.
I need to forward the following ports:
UDP: 3074; 3659; 6000
TCP: 80; 443; 3659; 10000 - 10099; 42127
Have previously given the PS3 a static IP, set the port forwarding rules and then forwarded to the IP address, but it appears the ports have not opened as expected.
Help Keith

I can only see one image which just shows the application mapping, but no indication as to whether you had clicked the "apply" button.
Why are you forwarding ports 80 and 443, are you running a webserver on the PS3, as those ports are used for web serving.
As a matter of interest, your port 80 is showing as open at the moment, so is the PS3 turned on, or is port 80 mapped to something else instead?
What I would like you to do is to start from the beginning, with just the single TCP port number 3659 assigned to the PS3.
It will mean removing the other assignments, but it will make things a bit easier.
If you could do that please, and then we can do some tests.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Help with port forwarding for the WRT54G

I need assistance please!
I am having issues trying to setup port forwarding for a ftp. I already have set this up for a SQL Server port and it works remotely. When I setup another rule for ftp using port range 20-21 it does not work.
I have confirmed that I have saved my settings, have the correct IP address, etc. I have firmware version 4.21.1 and not sure how to troubleshoot this. Any help would be great.
Thanks,
John

Yes you do need to have the port already forwarded for port 20~21 with both TCP/IP and UDP enabled unless you know for sure your ftp only uses just one of them. That is why I asked what port your SGL was set to. Follow the link that other guy posted and open port 20 and 21 (I only use 21 with no problems) and make sure it is directed to the IP of the ftp host. Also that PC needs to have the FTP enabled in windows. To do that go to your control panel > add/remove software > and on the left side go to add/remove windows components. Then check the box for the ftp and add it. It should ask for your windows CD do have it handy when you add the ftp component to your PC.
Richard Aichner (Ikester)

Help with port forwarding ASA5505 v8.2

Hi,
Having an issue doing a port translation on an ASA5505 for RDP.
I have a /29 allocated by ISP and when I port forward the address assigned to the outside interface RDP works perfectly, however when I try to use another IP within the /29 range, I get nothing.
I am only new to ASA so please forgive if this is something obvious...
Relevant config is:
interface Vlan1
nameif inside
security-level 100
ip address 10.1.12.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address X.X.X.217 255.255.255.248
access-list OUTSIDE-IN extended permit tcp any host X.X.X.218 eq 3389
static (inside,outside) X.X.X.218 10.1.12.10 netmask 255.255.255.255 sh run acces
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
access-group OUTSIDE-IN in interface outside
When I used the outside IP address and it worked perfectly, config difference was only
access-list OUTSIDE-IN extended permit tcp any host X.X.X.217 eq 3389
static (inside,outside) tcp X.X.X.217 3389 10.1.12.10 3389 netmask 255.255.255.255
Any help would be greatly appreciated

Hey Jouni,
Packet capture gave me this output which didnt have any TCP 3389... but had some random UDP ports only?
   1: 21:54:55.108377 802.1Q vlan#2 P0 X.X.X.218.63420 > 208.67.222.222.53: udp 44
   2: 21:54:58.751929 802.1Q vlan#2 P0 X.X.X.218.63420 > 208.67.220.220.53: udp 44
   3: 21:54:59.492238 802.1Q vlan#2 P0 X.X.X.218.63976 > 208.67.222.222.53: udp 45
   4: 21:55:02.807468 802.1Q vlan#2 P0 X.X.X.218.63207 > 216.239.34.10.53: udp 55
   5: 21:55:02.807651 802.1Q vlan#2 P0 X.X.X.218.63976 > 208.67.220.220.53: udp 45
   6: 21:55:06.863495 802.1Q vlan#2 P0 X.X.X.218.63414 > 199.253.183.183.53: udp 56
   7: 21:55:24.599563 802.1Q vlan#2 P0 X.X.X.218.65039 > 208.67.222.222.53: udp 42
Config is below:
ASA Version 8.2(5)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 3
interface Ethernet0/2
description TO LAN
interface Ethernet0/3
description TO LAN
interface Ethernet0/4
description TO LAN
interface Ethernet0/5
description TO LAN
interface Ethernet0/6
description TO LAN
interface Ethernet0/7
description TO LAN
interface Vlan1
description TO LAN
nameif inside
security-level 100
ip address 10.1.12.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address X.X.X.217 255.255.255.248
interface Vlan3
shutdown
no forward interface Vlan2
nameif backup
security-level 0
ip address X.X.X.42 255.255.255.252
ftp mode passive
dns server-group DefaultDNS
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group icmp-type ICMP
description ICMP types permitted
icmp-object echo
icmp-object echo-reply
icmp-object unreachable
icmp-object time-exceeded
access-list OUTSIDE-IN remark TRAFFIC PERMITTED TO ENTER THE OUTSIDE INTERFACE
access-list OUTSIDE-IN extended permit tcp any host X.X.X.218 eq 3389
access-list OUTSIDE-IN extended permit icmp any interface outside object-group ICMP
access-list INSIDE-IN remark INSIDE ACCESS
access-list INSIDE-IN extended permit tcp any any
access-list INSIDE-IN extended permit ip any any
access-list INSIDE-IN extended permit icmp any any
access-list BACKUP-IN remark TRAFFIC PERMITTED TO ENTER THE BACKUP INTERFACE
access-list BACKUP-IN extended permit icmp any interface backup object-group ICMP
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu backup 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
global (backup) 1 interface
nat (inside) 0 access-list NO-NAT
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) X.X.X.218 10.1.12.10 netmask 255.255.255.255
access-group INSIDE-IN in interface inside
access-group OUTSIDE-IN in interface outside
access-group BACKUP-IN in interface backup
route outside 0.0.0.0 0.0.0.0 X.X.X.222 1 track 1
route backup 0.0.0.0 0.0.0.0 X.X.X.41 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 1
type echo protocol ipIcmpEcho X.X.X.X interface outside
num-packets 3
frequency 10
sla monitor schedule 1 life forever start-time now
track 1 rtr 1 reachability
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp

Help with port forwarding

i am running a web and mail server from my home computer. i have port 25 and port 80 set to forward traffic to my webserver. port 80 works ok, but according to the linksys log, the linksys router is blocking port 25. My isp is not blocking any ports, and i can send mail from my mail server. how can I get the linksys router to stop blocking incoming port 25? my router setup is: linksys befw11s4 port forwarding: 80 to 80 25 to 25 upnp is enabled upnp forward smtp 25 tcp to port 25 192.168.X.X dmz is enabled for the server's ip.

wiles wrote:
i am running a web and mail server from my home computer. i have port 25 and port 80 set to forward traffic to my webserver. port 80 works ok, but according to the linksys log, the linksys router is blocking port 25. My isp is not blocking any ports, and i can send mail from my mail server. how can I get the linksys router to stop blocking incoming port 25? my router setup is: linksys befw11s4 port forwarding: 80 to 80 25 to 25 upnp is enabled upnp forward smtp 25 tcp to port 25 192.168.X.X dmz is enabled for the server's ip.
First off, DISABLE the dmz!! That opens ALL ports to your pc, you dont want that.
Second, because you had the pc in the dmz tells me that the router is not blocking port 25, again, in the dmz all ports are open.
Disable upnp, it will just cause problems and you arent using it anyway.
Go to :
https://www.grc.com/x/ne.dll?bh0bkyd2
Click proceed, enter 25 in the box in the middle, then click user specified custom probe.
Does it show as stealth?

Need help with port mapping on Airport Utility 6.1

Ive been trying to port map on my TC with Airport Utility 6.1 and failing miserably. Port still closed. Can anyone advise where Im going wrong? Am trying to set up my home camera to be viewed outside.
I managed to key in the ports etc under Network and Port Settings. But nothing works. I'm tearing my hair out.
Any suggestions to try would be helpful.
Thanks

Use the 5.6 utility.. it is much easier and I think works better.. although you cannot load 5.6 directly into 10.8 the version for Lion actually works fine.
Download 5.6.
http://support.apple.com/kb/DL1482
Download unpkg
http://www.macupdate.com/app/mac/16357/unpkg
Open the AU 5.6 dmg and drag the pkg over the open unpkg.. it will create the directory on the desktop. You can either run it from there or drag the utility to your utilties directory.
Take screen shots of each step. Post them here.
That way we can tell you where it has gone wrong.
What port exactly does the camera need open?
How are you connecting remotely?
ie do you have a fixed public IP?? If not how are you getting IP?
Is the TC the only router in the network.. it is irrelevant unless the TC is the one and only router.

Help with Port forwarding issue...

I have a new extreme base station at work currently opening a port # to a imac running a business app. Works fine, BUT I need to open another port # pointing to the exact same imac for using another related program. I opened airport utility did the exact same procedure as the working port but I can't seem to open any new #'s?? Any way to type in "Test port numbers" and check with portscan? I tried a few numbers and Nothing. The only one that comes back open is that one working port #. Nothing is blocked in sharing on the pointed iMac. Called my isp and they said they're not blocking anything. Tried power reset on the exteme and the iMac. No change. ANY help would be MUCH appreciated!! Thanks in Advance...

Here's an example of two such setups on my AEBS:
Notice that each service has its own ports but both point to the same machine IP address. Try using the machine's IP address assigned in Network preferences.

Need help with porting from Java 1.1 to 1.4

One of our applications is an applet and we're in the
process of upgrading it's version of Java from 1.1 to 1.4. For the most part,the upgrade has gone smoothly, but we are having two big problems. The first problem is that the list objects on one of the windows resize when a mouse event occurs on the Tabbed Panel it sits on. The list object is made from a Symantec class called MultiList. The list actually shrinks so that the data on it can hardly be seen.
The other problem is that when dispose() is called on all of the windows, an IllegalStateException: Cannot dispose InputContext while its active error occurs.

If you people have nothing good to say, please do the
rest of us in the forum(s) a favor and don't say
anything at all.
Also, do not assume that threads are posted because
people are lazy and haven't researched their
problem(s).
People post threads in these forums looking for help,
not abuse.What are you talking about?
If the original poster disregarded my advice and searched the bug database as indicated, they would have found the answer to their question. I know. I had the same problem and solved it by using the workaround I found in the bug database.
I would say it was very helpful advice.

Problem with Port Forwarding (when PPTP is up) in WRT-160N

Hi, everybody!
I'm looking for some help with Port Forwarding in my new router from Linksys. I've bought the router afew daysago, and was badly surprised when I found out that there is DD-WRT firmware is installed in it (the router was 100% NEW when I've purchased it). I have downloaded the latest original Linksys firmware file and successfully flashed it.
But I still have problem (same I had on DD-WRT firmware too) with port forwarding for my DC++ and Vuze (app for torrents): I've written port forward for ports 49151 (for Vuze) and 4000 (for DC++) to be forwarded to my desktop computer (IP 192.168.1.201) -- I've seen a post at this forum, that there could be a problem, if you forward to an IP, which is inside DHCP local zone, so I've forwarded it to .201 IP (my local DHCPzone is 192.168.1.100 - .149). But forwardind doesn't work ((
What's wrong?
My configuration:
Router IP: 192.168.1.1
PPTP (I've got it from my ISP)
IP address: 192.168.226.127
Default Gateway: 192.168.226.2
DNS 1: 192.168.1.1
DNS 2 & 3: 0.0.0.0
PPTP Server IP Address: 192.168.226.2
Username: ****
Password: ****
Single Port Forwarding:
Application name     External port     Internal port     Protocol     To IP address     Enabled
Vuze 49151 49151 Both 192.168.1.201    Checked
DC    4000 4000            Both           192.168.1.201 Checked
Solved!
Go to Solution.

As you have mentioned in your post that your ISP has provided you a PPTP connection with an IP address: 192.x.x.x. The IP address which is provided to you by your ISP is in a Private Range, and if you try to forward any ports on your router it will not work, as your ISP modem will block that port. So you need to get a Public IP address from your ISP.
As you are getting Private IP from your ISP, so this connection is called as NAT behind NAT, and your Modem is acting like a Router.
So now you have 2 options, get the Public IP address from your ISP or change the connection type.

HELP!! asa 5505 8.4(5) problem with port forwarding-smtp

Hi I am having a big problem with port forwarding on my asa. I am trying to forward smtp through the asa to my mail server.
my mail server ip is 10.0.0.2 and my outside interface is 80.80.80.80 , the ASA is setup with pppoe (I get internet access no problem and that seems fine)
When I run a trace i get "(ACL-Drop) - flow is deied by configured rule"
below is my config file , any help would be appreciated
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISPDsl
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_SMTP
host 10.0.0.2
access-list outside_access_in extended permit tcp any object server_SMTP eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network server_SMTP
nat (inside,outside) static interface service tcp smtp smtp
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:c5570d7ddffd46c528a76e515e65f366
: end

Hi Jennifer
I have removed that nat line as suggested but still no joy.
here is my current config
Result of the command: "show running-config"
: Saved
ASA Version 8.4(5)
hostname ciscoasa
domain-name domain.local
enable password mXa5sNUu4rCZ.t5y encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.0.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group ISP
ip address 80.80.80.80 255.255.255.255 pppoe setroute
ftp mode passive
dns server-group DefaultDNS
domain-name domain.local
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Server_Mail
host 10.0.0.2
access-list outside_access_in extended permit tcp any object Server_Mail eq smtp
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (inside,outside) dynamic interface
object network Server_Mail
nat (inside,outside) static interface service tcp smtp smtp
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 10.0.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
vpdn group ISP request dialout pppoe
vpdn group ISP localname [email protected]
vpdn group ISP ppp authentication chap
vpdn username [email protected] password *****
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f3bd954d1f9499595aab4f9da8c15795
: end
also here is the packet trace
and my acl
Thanks

Need help with a WRT54GS V5.1

i need help with my WRT54GS V5.1 wireless router. it cannot connect to the internet and i don't know why. at the moment i have to use an ethernet cable coming from a virgin media modem. information that might be usefull. one of the antennas on the router is broke i am using windows vista on a toshiba laptop. the model is WRT54GS V5.1 thanks for people who help note: i am only 13 so somethings you say i might not understand.

Access Setup page of router .....
Click wireeless tab .... have a note of the wireless settings on that page .... Please click on the tab "Application and gaming" and click on sub
tab "Port range forwarding"
1) On the first line in Application box type in "Xbox", in start box
type in 88, in end box type in 88, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
2)   On the second line in Application box type in "Xbox", in start box
type in 3074, in end box type in 3074, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
3) Now save the settings
4) Once you return to the setup page, click on the tab "Administration"
and disable the UPNP and save the settings.
5) Now assign the given ip address on your xbox
   ip address :- 192.168.1.20
   subnet mask :- 255.255.255.0
   default gateway :- 192.168.1.1
Please assign the dns address on the xbox
primary dns :- 4.2.2.2
secondary dns :- 192.168.1.1
6) Please try to test your xbox live.

Hi newb here , Can anyone help with Port Forwardin...

Hi guys
Newb here on Broadband Option 3 .
New to the world of BTorrents ( hope thats not a dirty word ) and just need some help on Port Forwarding with the Curved Blue Voyager ( latest one I think )
Problem is I can't seem to upload anything back and obviously I dont just wanna leech all the time lol
Thanks in advance
H

First of welcome to BT Community Forums, although your in the help with speed/connection issues section and bit-torrent is nothing to do with BT but i'll still try to help.
downloading a torrent file is one thing but just because you download does'nt mean you need to upload anything if for example your downloading something with say 100 seeders and 15 leechers then you may find that you dont upload anything or very little, thats nothing to worry about at all.
Or
If you've made a torrent and cant figure out why its not uploading it may be due to the fact you need to upload the small torrent file to a p2p site in order for others to see it.
Hope this small insight into the world of torrents helps, but i dont know what else to tell you on this subject.
Kindest Regards
IceZaroth
BT Community Helper

New Customer Experience with Port Forwarding

OK, so my OpenReach Modem and HomeHub 3 were installed last week and all seemed OK at first.
A bit of background:
I'm a seasoned IT guy and have a nice network set up at home that caters for my needs (most of the time).
Without going into too much detail, I have my own DHCP/DNS server and I run a Webserver for personal use.
I have Virgin Broadband - which work most of the time.
I've also just had BT Infinity installed so I should always have Internet access no matter which ISP is having issues.
I was hoping to be able to access my webserver externally from either my BT or Virgin. I didn't think this would be an issue.
It still all works fine through my Virgin connection. I use dynamic DNS (no-ip.org) to get to my server.
On the Virgin Superhub - I have DHCP switched off and all my machines (except one at the moment) get the Virgin router assigned as the Internet gateway (via my own DHCP server).
My test machine gets a the BT HomeHub 3 assigned as the Internet gateway (also from my own DHCP server) and I have switched off DHCP on Home Hub.
Before I move onto my issue, I have to say that the above network setup works flawlessly.
The Virgin Router is on 192.168.0.1, The Home Hub is on 192.168.0.2. (subnet 255.255.255.0)
They are on the same network but because DHCP it switched off on both routers - everything is happy.
I can access my Server from the Internet via my no-ip.org address and it all works great.
The issue:
I thought it would be relatively simple to configure the BT Home Hub 3 to access my server from the Internet.
Hmmm. Port Forwarding seems to be the issue. It just doesn't work reliably enough. Sometimes it works, then sometime it stops working. Right now it's not working.
At first I though it was just me, not configuring it correctly. But no.
Then I started reading this forum and found there are reports of issues with port forwarding going back a year.
I don't know if that a good or bad thing - an issue running that long must be on the verge of getting fixed right?
Or any issue running that long without resolution probably has no simple resolution or just isn't a priority (for BT) maybe.
My Question:
(and I think I already know the answer)
Has anyone got a sure fire way of configuring the HomeHub3 so the port forwarding works?
Or should I just throw in the towel now and buy a Dual Wan Router?
One last note:
This morning my Infinity Broadband Speed dropped from
38Mb down/6Mb Up (measured several times yesterday)
to
0.7Mb down/0.3Mb Up (yes those decimal points are in the right place)
And I haven't got a clue why.
I power cycled the HomeHub and it returned to normal. Does this happen to other people?
Cheers
Graeme.
Graeme

Bullitt wrote:
the port on your network is defined by lan ip address and port number eg 192.168.1.10:80
you cannot forward this outbound port twice
There is no "port on my network" A port is associated with a IP address not a network.
My webserver listens an port 80 - requests from the Internet for http are port forwarded by the router (either BT Homehub or Virgin Superhub) to port 80 at address 192.168.0.5 (in my case).
If I am trying to access my webserver from the Internet, I point my browser at the WAN IP address of my router (again it doesn't matter which one - BT or Virgin) and the router port forwards the request to my Webserver. Each router can do this independently.
"you cannot forward this outbound port twice"
As explained above - It's an inbound port not an outbound port.
I appreciate you are trying to be helpful but just telling me something is not possible without explaining why its not possible doesn't really help me.
As I said before, this was working fine, then it stopped working but only when trying to access my webserver via the BT Router. It still works fine from my Virgin Router. I used WireShark and port mirroring on my switch to prove that the Home Hub as stopped port forwarding inbound traffic to my webserver.
This is a problem with port forwarding on the Homehub, not my network setup. Looking at other posts on this forum - I'd suggest I'm not the only one having problems.
To be honest, it's the least of my problems with the HomeHub right now. I'm far more concerned with the fact that twice today I've had to power cycle it because the throughput has dropped from 38Mbit-down/6Mbit-up to <1Mbit-down/<1Mbit-up. It's a known problem, BT are working on it, yet I still am paying full price for a product that should never had made it out of Beta test.
Graeme

Need help with port forwarding an Avtech DVR

Similar Messages

Maybe you are looking for