Need Help with WRT54G version 5. Connectivity

I have a laptop that is gaining wireless access from a remote router, I also have a WRT54G V5 router that I want to connect to the laptop and use to send a signal to another PC(with antenna).  I would think this is possible, but not exactly sure how to go upon it.  Please be specific with any replies as I am not the sharpest tool in the shed when it comes to computers.  Thanks.

The set-up you are trying will not work if you are trying to communicate your remote router wirelessly to the WRT54G router...It is indeed possible if you can connect your remote router using an ethernet cable to the WRT54G router...

Similar Messages

  • Need Help with iTunes version

    I recently downloaded IOS 7 for my iPhone 4s.  In order to keep it updated and sync my music, I need the 11.1 version of iTunes or a later version than that.  Where would I find this?

    Hi,
    iOS 7 is not due for release until September 18!! iTunes 11.1 is not available yet - due at same time?
    Jim

  • Need help with WRT54G installation

    I just replaced a BEFSR41 with a WRT54G v.8, and came across an installation problem. I had no problem manually installing the BEFSR41 by following the Start Fast instruction. Since the WRT54G didn't come with a Start Fast document, I used the CD instead. After connecting the router to the PC (winXP), and the modem to the router, I kept getting a message about not being able to connect to the Internet. But in fact I was connected, and could access the Net fine. Is there something need fixing? Perhaps another factory reset? A few other questions:
    - When I tried to print the settings, I was asked to install a printer. But I already have three printers installed. How can I print or save the settings?
    - After exiting setup, browsing 192.168.1.1 showed a blank page. ZoneAlarm was disabled, and all other pages worked fine. What is going on?
    - My firmware version is 8.00.2. Should I upgrade it.
    Once I get these resolved, I have some very interesting speed test data to share.

    Update. After factory reset and firmware upgrade, I followed the manual installation suggested in the archive here:
    http://forums.linksysbycisco.com/linksys/board/message?board.id=Wireless_Routers&message.id=146133&query.id=553973#M146133
    Now things seem a lot better. The firmware rev is now 8.00.8, and I can access the 192.168.1.1 page. Please let me knwo what else I should check. Still have to shut down ZoneAlarm to browse with Firefox.
    I'll repeat the speed tests and report later.

  • Need help with wrt54gs v7

    i think my router is dead but heres the info
    the 1-2-3-4 ethernet lights are flashing and the internet light
    ive tried holding down the reset button for 30 secs and nothing happens
    computer doesent recognize it and i cant get any type of connection out of it

    i really hope someone can help me with my situation that i'm in. My WRT54GS v7 been acting on me. I had a network establish on it connecting to my Xbox 360. When i switch different game systems i disconnected my game adapter and the router from the modem for a short period. Later i connect everything again and it went fine. I just changed security settings and tired to reconnect my game adapter back to the xbox 360 and nothing happen. It couldn't find the router. Later after several different trial and errors. It found it. Still couldn't connect. First the network and then the IP address stop the game adapter from working couldn't connect fully to the router. so i went back on trying to set the router to allow the game adapter in. Change the settings back to normal and then a message about detecting new changes makes this your defalut settings so i tried , but now couldn't detect the router ( even though it's right there not even 3 feet away). So i did what i was told to my the Linksys advisor to detect the router. Rest 10 seconds , connect, wait 30sec. , click next. I went to help and followed more instructions there. I reset the router several times. I uninstall and reinstall, went to web site to go to factory default. Tried on the game adaptor the reset, type manually on xbox ,but to no avil have i succeed. I also went online and tried these commands. Ipconfig/ renew, release, all(for info). I need a miracle so please can someone help me on a permant fix. Since resetting, reinstalling, refactory defaulting doesn't seem to work..Also how can iconnect my game adapter to it. I used the set up for both router and game adapter and i'm still stuck where i am. :[

  • Need help with wrt54gs v.5!!

    WRT54GS v.5
    Ok so i had my router set up perfectly. I recently re-arranged my room so i had to disconnect the router. Now when i hook everything up, it doesnt work. I get the flashing "power" led. I tried looking though the troubleshooting section of the manual where it says to hold the reset button for 5 seconds.. nothing. so i try 10 seconds to reset the whole thing.. nothing. Still same problem.
    The manual suggest maybe the firmware might have got corrupted. So this is where I am at. I can not seem to connect to the i.p address to get to the setup. What do I need to do to get this resolved?
    My mom needs the connection in her room to take care of some things and Id rather not her take up my time usin my computer in my room haha. Please help!! THanks ~AustinMessage Edited by hypertek on 09-17-2006 10:22 PM

    Reset the router for 30 seconds and power cycle.You can also try a different power socket.Other option would be to give a static ip to the computer h/wired to the router -- ip add : 192.168.1.10 and default gateway : 192.168.1.1 and if you are able to ping the default gateway try to upgrade the firmware.

  • Need help with WRT54G - no software and problems with internent

    I'm sure I'm asking a common problem which has been answered already, but I couldn't find any solutions and I'm running out of time (re: getting frustrated as hell). I'm trying to set up a wireless network at my home. The internet/desktop/cable modem work fine. However, when I try to run the connection through the router, the connection fails. The appropriate lights on the router all light up, however. Is there something on the pc I need to do/change? Also, the disk drives on the pc don't work, so I can't load the setup software. Any help would be extremely appreciated.

    What is the Version no. of your Router ? You can see it when you flip the router..
    As your Internet Service Providor is Cable follow this link to configure your Router.

  • Need Help with iPod Version

    I want to put Linux in my iPod but I need to "unUpdate" it to v 1.0 (its updated to 1.2 right now). I tried alot of stuff but never works...
    I got the 20gb iPod photo (the generation just before Video iPod)
    When I use "restore", my iPod stay at V1.2
    Could someone help me please?
    Is there any way to unUpdate an iPod?
    Thanks for your help.

    See you can have an older version iPod updater here
    http://www.ipodwizard.net/showthread.php?t=7369
    By the way, I suggest you do not put Linux on you iPod, as you will loss the warranty immediately. Also when your iPod get into trouble, it is not easy to revert back

  • Need help with wrt54gs

    well i am new to the whole "wireless network" idea as i have used my trusty cable modem for a while now. I have sucessfully intalled the help software and have a linksys wirless adapter on my computer. It reads connected to the access point but the internet cannot be found. i do not know what this means as i am new to this. please if you can make your posts easy to understand and not in gibberish. this will be greatly appreciated. thanx!!'
    Also i am trying that thing it said on FAQ
    Message Edited by HelpingHand on 09-16-2007 09:45 PM

    I think u are trying to create a wireless network in ur place, though u have installed the router why ? dont u start from scrap.
    Hardreset the router for half a min & where u will find lights flashing & then stable.turn off & on both router & modem hardwire any pc to router with ethernet cable. & from router  to modem connect another ethernet cable.
    check all the lights are there for the connections made.
    make sure dont put the disc in PC , do manually , Open the setup page on IE which is normally default 192.168.1.1 , u will get authentication where there is no Username & password is ' admin '
    In basic setup u will find sub tab " Mac add clone ' make ; enable' , then 'clone my pc's Mac' & save & then u can configure wireless settings accordingly just understand the meaning of those Tab's .
    After completion try connecting wired 1st & then wirelessly.
    trie ou...any probs reply...?

  • Need help with latest version of Google Maps

    Have the 8700 series Blackberry, google maps 2.0.3 worked fine for last 2 years, upgraded to 2.3.2 yesterday and the application downloaded but wont run.  Starts to run and then get the following message:
    'Network unavailable: This application requires a data connection and some Blackberry devices require reconfiguration to work properly'.
    Can connect to the Internet using browser just fine, all other features of the blackberry working just fine.
    Any help would be appreciated.
    By the way, did already uninstall and reinstall the application a few times.  I wish I had kept the old version just in case.

    Seems that new version GoogleMaps does not work on your device.
    You can install old version on your device.
    If old version does not work after uninstalling new version and installing old version do the following:
    Backup your sensitive data via Blackberry Desktop Manager.
    Wipe your device memory:
    Go to: Options - Security Options - General Settings
    open menu and select "Wipe handheld"

  • Need help with WRT54GL, can't connect on wireless just cable

    Hello,
    I have a WRT54GL, firmware 4.30.5. It is connected to a cable modem. I have two computers, one mac and one pc using XP SP2. Mac works great with its airport adapter but the pc only works with the cable. I tried two separate wireless USB adapters but can't get it to connect to the internet.
    I can connect to the router but it keeps getting stock at the acquiring network address. I already set the Mac filter and the connection is Excellent but no internet.
    Router is set to Auto DHCP. I appreciate any help.
    Thank you all,
    Nicko

    Thanks for your help. Actually late last night I installed the EasyConnect Utility from Linksys.com and it managed to connect to the wireless router and connected to the Internet. But now my problem is the connection is VERY SLOW. The signal strength is Excellent but it takes a long while to download any page with flash or images. I did a Speakeasy.net speed test and it came our under 100K for download and about 200K for upload. When I connect a network cable directly to the router then the speed shoots up to over 1.5M+
    Thanks again,
    Nicko

  • Need help with sonos speaker setup, connecting to music through an NAS hdd on AirPort Extreme.i

    i Cannot figure out how to connect the sonos speaker with the right path. It also wants a password for the disk and I don't recall setting up one. My speaker works fine through my pc or MacBook but I want to play music from a shared folder on an hdd that is connected to my AirPort Extreme. Any ideas or experience with this???

    Called Sonos, they got me all setup.

  • Need help with a Java-SQL connection

    My classmates and I created a DesktopFrame. Within it are reports that require a connection to an MS Access Database. When a report in an InternalFrame is opened: the SQL command works, there is a connection, and everything goes well on the first run.
    However, when another InternalFrame is opened or when the same InternalFrame is opened the 2nd time, an error occurs. It produces a java.sql.SQLException: General Error.
    Can anyone help me? Thanks in advance.

    Provide more info, maybe even some code segments. (Not all). May be easier to help

  • I need help with WRT54G v. 4 and xbox

    I keep getting freezes whenever anyone else on my network accesses the internet. All the computers are wireless, only the 360 is wired. I have set the MTU for 1365. I attempted to set the 360 for a static ip so i could forward ports to it, but whenever I try to test it, it always says that the ip test is failed. I can get my computer on with a static ip, why not the 360? Please help

    Hi.
     Try using the static IP 192.168.1.10 SM 255.255.255.0 and Default Gateway 192.168.1.1 on the XBOX. ( Supposing your router is set to default IP).  After assigning  the static IP powercycle the router and check the connection if the IP test fails try upgrading  the router firmware. Also check the type of cable that you are using to connect between the router and the Xbox.

  • Begginer needs help with what version of Photoshop?

    Let me clarify.....
    Back in 2008, I bought an E-Machine Desktop that had "Adobe Photoshop" bundled on it.
    I bought a new HP 6719C computer last year.
    It has no Photoishop program whatsoever.
    I LOVED my old version of Photoshop.
    The feature I liked most was the erasing Tool, were you could put your head on someone elses boday, and the "Clone" feature, to take out unwanted items in your pictures.e to Download a version of Adobe Photoshop, that closely resembles the Features I described above.
    Not looking for anything, super-dooper fancy.
    Just pretty much the Basics.
    So what is this "Adobe Elements" program all about.
    What would be the simpelest, least complicated program, to get me started after a 5 year Hiatus without Adobe Photoshop?
    Roger

    Photoshop Elements 10 should do what you need.
    You could download a thirty day trial and see if it does what you need.
    There is also the photoshop elements forum for more in depth questions about photoshop elements features:
    http://forums.adobe.com/community/photoshop_elements

  • I need help with Pages version 5.0.1 desperately

    I'm trying to create table of content and could not find the TOC under inspector. Please help

    Viking
    That should be:
    Menu > Insert > Table of Contents
    Apple has inconsistently not put in the Toolbar Insert
    Peter

Maybe you are looking for