Need Help WRT54G v5 Wireless-G Router Cannot Access Internet

Hello, we have been experiencing trouble with our router. Using our wireless router we cannot connect to the internet. We use a cable to connect the modem to the router to the computer.
This problem first occured when a buddy of mine connectred to our wireless signal with his Xbox-360 Wireless adaptor. After that we could not connect to the internet using our router.
Any help would be greatly appreciated 

Logon to www.linksys.com/downloads and download the firmware for the router  and upgrade the routers firmware and reconfigure it .

Similar Messages

  • Need help to set wireless Linksys Router WRT150N to work with Nettalk Duo

    I have Linksys Router WRT150N , connect to it Nettalk Duo but there is no ring tone, the orange light is flashing trying to connect, then i have the green light blinking then go Red.
    I thied to call Nettalk but no answer to their phone, chat with customer support at last they said someone from technical support will call back, but that not happen since two weeks.
    I make several tickets to them but no reply, service is very bad.
    Please any help to configer inside the router to recognise Nettalk, i have cable internet they said there is no blockage from there side.

    Hey sam63. Based from what I've read, RED lights means the device has failed to connect to the network. I'd suggest that you perform a powercycle. Unplug the power of the NetTalk Duo and the router for 30 seconds. Once done, power on the NetTalk first then, the router. Also, make sure that it is properly connected to the router's Ethernet port and the router is working online. You may try using another Ethernet cord or plug it into another Ethernet port. 
    If that won't work still, I found a link that might help you. Here: http://www.nettalk.com/support/customer-support/
    Help, learn and share

  • IPhone connected to Apple Wireless Extreme but cannot access Internet

    I have the Apple Wireless Extreme that I use to connect my MacBook Pro online, and for some reason the iPhone cannot access the Internet. I can connect to the base station, but can't go online - it's getting an IP address and I can see the DNS server addresses. I have tried no security, WEP, WPA and WPA 2 with no luck. I have to resort to connecting to someone elses wireless network so I can go online with the iPhone.
    Any ideas?

    I have an Airport Extreme base station using WPA2 Personal encryption for my wireless network without MAC filtering, and I connect with my network with no problems.
    How many characters is your password when using WPA2 Personal encryption?
    I would also try resetting your wireless network.
    Power your MB and your iPhone off.
    Power your Airport Extreme Base Station off, and then your modem.
    Wait several minutes and then reverse the process.
    Power your modem on allowing it to completely reset and connect.
    Power your Airport Extreme Base Station on, allowing it to reset with the modem.
    Power your iPhone on and try connecting to your wireless network.

  • Wireless clients unable to access internet on new WRT54G - Help!

    I have multiple wireless clients that cannot access the internet. They all get valid IP addressing. I can ping the router. But I can't access anything on the internet. I just setup this router and I do this sort of stuff for a living and I give up. It shouldn't be this difficult. Two of the clients are Vista and the other is XP. Again, the connection to the router is perfect. I just can't access anything beyond the router. The single wired client works fine. Help!

    Thanks... I've tried that. All of these hosts were actually working just fine with my old DLink router, but that router died over the weekend, so I replaced it with the Linksys. For the life of me, I can't see any reason why these hosts can't route out to the internet.

  • My hard disk crashed and I cannot find out how to "contact customer service" other than this forum.  The website seems to just take me in a circle. I need to de-activate a license but cannot access the software due to a crashed hard drive.  Please help.

    My hard disk crashed and I cannot find out how to "contact customer service" other than this forum.  The website seems to just take me in a circle. I need to de-activate a license but cannot access the software due to a crashed hard drive.  Please help.

    Hi Anthony ,
    Here is the link to connect with Adobe Chat Support.
    https://helpx.adobe.com/adobe-connect/kb/connect-chat-support.html
    Hope your query gets resolved .
    Regards
    Sukrit Dhingra

  • I am connected to my wireless network but cannot access the internet. Any ideas?

    I am connected to my wireless network but cannot access the internet. Any ideas?

    Your router may not have given your iPad a valid IP address. Go to Settings > Wifi > your network name and touch the ">" to the right to see the network details. If the IP address starts with 169 or is blank then your router didn't provide an IP address and you won't be able to access the Internet.
    Sometimes the fix can be as simple as restarting your router (remove power for 30 seconds and restart). Next, reset network settings on your iPad (Settings > General > Reset > Reset network settings) and then attempt to connect. In other cases it might be necessary to update the router's firmware with the latest from the manufacturer's support web pages.
    If you need more help please give more details on your network, i.e., your router make, model and version, the wifi security being used (WEP, WPA, WPA2), etc.

  • TS3798 I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

    I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

    amarilysfl wrote:
    "Your disk could not be partitioned. An error occurred while partitioning the disk".
    https://www.apple.com/support/bootcamp/
    If you were using Apple's BootCamp and received this message, quit it and open Disk Uility in your Applicaitons/Utilities folder.
    Select the Macintosh HD partition on the left and select Erase and Erase Free Space > Zero option and let it complete (important) this will check the spare space for bad sectors that can cause issues formatting partitions.
    Once it's completed, try creating a partiton again in BootCamp.
    If that doesn't work, then hold command option r keys down while connected to a fast internet connection, Internet Recovery should load (spinning globe) and then in that Disk Utility, select your entire internal drive and click > First Aid > Repair Disk and Permissions.
    reboot and attempt Bootcamp again.
    If you still get a error, it might be that you have OS X data on the bottom area where BootCamp partition needs to go. This would occur if you had the drive or computer for a long time or wrote a large amount of files to the drive and nearly filling it up and then reduced some, but it left traces in the area BootCamp needs to go.
    To fix this
    BootCamp: "This disc can not be partitioned/impossible to move files."
    How to safely defrag a Mac's hard drive

  • VPN Client cannot access Internet

    I am currently using PIX 501 and VPN 3000. Everything is running fine except that VPN Client cannot access internet after they logged in via Cisco System VPN CLient. I can't any solution to this problem and is really lost. This is a very important task assign to me.
    Hope someone can help me asap.
    Thanks You

    You need to enable split tunneling. This link is for VPN client to router. The same equivalent config may apply to a PIX as well.
    http://www.cisco.com/application/pdf/en/us/guest/products/ps6659/c1650/cdccont_0900aecd80313bf8.pdf

  • My ipad cannot access Internet although I have strong wifi signal

    My ipad cannot access Internet suddenly although I have strong wifi signal & my iphone, macbook and other laptops can connect to the wifi network. I tried to reset the network settings, connect to itunes, check the router. but it doesn't work. Can anyone help me please to solve this problem? Thank you very much

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Cannot access internet after upgrading to IOS 6.1.2 on iphone 4

    cannot access internet after upgrading to IOS 6.1.2 on iphone 4.

    ok here is the issue.
    After i upgraded the IOS to IOS 6.1.2 I'm not able to use mobile internet as i have a data sim card.
    As the settings provided by the service provider are not compatible with IOS 6.1.2 and the service provider cannot do anything about it, as it's something that has to be ressolved by apple.

  • My iOS 6.1.4 is updated. i have other devices connected to wifi hotspot of my iphone5. Though my other devices appeared to be connected and shows an excellent cignal strength, i cannot access internet. hope this will be fixed.

    my iOS 6.1.4 is updated. i have other devices connected to wifi hotspot of my iphone5. Though my other devices appeared to be connected and shows an excellent cignal strength, i cannot access internet. hope this will be fixed.

    I hope so too.  So what have you actually done to fix your issue?

  • I need help choosing a wireless router (Networking Noob)

    Okay, I am very new to wireless networking. 
    I basically want to replace my current wired DSL modem with a wireless modem/router that I can still wire my main PC up to via Ethernet, and route a wireless connection to a laptop, and possibly some other devices (possibly a Nintendo DS, Xbox 360, TV, and other similar devices).
    I have been trying to find out if the E-Series from Cisco actually act as a modem as well as a router but can't seem to find the information.
    I do wish to have recent technology, but don't want to pay a fortune, so if there is a list of Linksys modem router combos you can give me then I can go research them further.
    If there is anything else you think I might need to consider, I'm all ears
    Thanks so much.  Hopefully I won't be a newbie for much longer on this subject.

    The E series routers are ethernet routers. They don't have modems integrated.
    The Linksys devices with integrated modem are the WAG models, e.g. the WAG320N.
    However, I would rather recommend a ethernet router and a standalone DSL modem. DSL technologies evolves pretty quickly and it's possible that the modem you buy today won't handle the internet speeds in two years.
    In addition, except for the latest WAG models (which can be configured as ethernet router on the first LAN port, i.e. "loosing" one of the four ethernet port) the DSL routers are generally only for use with DSL. If you decide anytime soon to switch to cable or satellite or FTTH you will need a new modem again.
    On the other hand, an ethernet router may be good for longer depending on your requirement. It works with any kind of access technology DSL, cable, etc. as long as you have a modem.
    Thus, my general advice is to get a standalone cheap modem and a separate ethernet router. Ask you ISP for the modem. Often, ISPs offer a simple modem for free or you get one "rented" for free. This way you have the guarantee that the modem works fine with their network.
    You also have a much greater variety of wireless routers to choose from.

  • WRT54G router cannot access the Internet

    My wireless PC can access the router but cannot access the Internet.
    When I ping linksys.com - the ping times out; however, when I ping my ISP I get 4 pings back. When I ping the router the ping is successful as I get 4 pings back.
    I am sure there is a fix for this problem. Can anyone help me get connected to the internet?
    Thanks
    I just got DSL in my area and installed it. I have a Linksys WRT54G router and a zyxek 660R DSL modem. I have a PC #2 in the room down the hall and a PC #1 in another room. I have a Wireless-G USB adapter in PC #2 (this is the antenna for the wireless connection). Everything is installed and PC #1 can connect to the internet through the modem and router. However PC #2 can only reach the access point (router) and will not access the internet. I can connect to the internet for PC #2 when an ethernet wire is used directly but it is not great to have a wire running down the hall. I pinged the router from PC #2 and the echos look fine. So it can certainly reach the router. When I use the Local Network tab and click on DHCP Clients table both PCs are displayed. So how can a PC use a wireless connection to reach the internet? I have spent 4 days already trying to get this to work. My ISP can't seem to help.
    Thanks for your help.

    hi... logon to router's setup page and try changing channel to 1 or 11, click on the advanced wireless settings and try reducing beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmware on the router...also
    if you are using Win XP system try uninstalling the adapter from the computer...click on start >> programs >> wireless G USB adapter >> uninstall, put the CD in for the adapter and restart the computer, one window pops up "found new hardware" try installing the drivers, no need to install WLAN software or utility and use windows WZC (wireless zero configuration) to manage wireless connection...check whether it works for you or not and let me know the results.

  • Need help configuring: 2 wireless routers with 2 different SSID's on one network

    Hello everyone: 
    I've been reading around on the forum trying to find the answer to this question, but have not found any clear cut answer that satisfies all my requirements.  A more in-depth explanatiion.
    I have 1 IP address coming in via cable modem.  I want to configure two wireless routers (one secured with WPA-TKIP, and one unsecured--a "guest network" if you will) each with different SSID's.  The secured network would be for my server, home PC's, IP webcams, DynDNS updating; while having an unsecured wireless router that friends and family can access.  Ideally, I do not want anyone who accesses the unsecured wireless router to be able to get access into my secured network.
    Can someone please tell me if this is possible.  I think it is based on some posts I have already seen, but specific details about how to do it would be appreciated.  Additionally, my DynDNS has to still be able to update with my ISP's IP so that I can access my server and home webcams.
    EQUIPMENT
    2 - WRT54G
    1 - EZXS55W
    1 - WVC200
    1 - WVC54GC
    (all of my stuff --webcam, server, dyndns, etc -- is working currently on my secured network. I just need to add the unsecured network)
    I know this is a lot, but I would appreciate any help.  THANKS.
    Solved!
    Go to Solution.

    You must have the main WRT54G router connected to the modem. Set up the secured wireless network on the main router. Connect all your wireless computers or devices to the main secured wireless network.
    Let's consider the IP address of the main router is 192.168.1.1.
    Now connect only one computer to the Port 1 on second wireless router.
    Open the setup page of the second wireless router. Change the wireless settings, SSID, unsecured.
    Change the IP address of the second router to 192.168.2.1. Save the settings.
    Connect the cable from the Ethernet port on the main router to the Internet port on second wireless router.
    Power cycle the second wireless router.
    Now the guest computers connected to the second wireless unsecured wireless network will be able to access the Internet only. They will not able to see the computers or devices connected to the first wireless router.

  • Need help wrt54gs

    i have a westell e90-610014-06 rev c modem at factory settings and a linksys wrt54gs wireless g router also at default settings. im using centurytel dsl. when i hook up my computer and modem to my router, the modem to the internet port i get nothing. i have a pppoe connection (i think) when i double click it to connect it brings up my username/password screen i enter them and it tries to connect. wont do it. but if i hook the modem up to one of the router ports (not the internet port) it will connect but then i cant get internet wirelessly. i've been working on this for days now and im losing my mind. please post anything that might help

    Only of the two devices should be setup for PPPoE connection...
    To setup a PPPoE connection you need to configure your Modem to Bridge Mode and then setup your router's Internet Connection Type to PPPoE...
    To setup PPPoE, Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
    When the router’s web-based setup page appears, click Setup then look for Internet Connection Type and select PPPoE on the drop-down arrow.
    Enter the username and password that your ISP provided you in the User Name and Password fields, including the domain in the username if necessary such as [email protected]
    Click Save Settings.
    Click Status then look for Login Status and check it says Connected. If it’s connected, you should be able to access the Internet.
    NOTE: If the Login Status says Disconnected, click Connect then check if you’re receiving an error message. To resolve error messages, please consult the link below.
    Resolving PPPoE Error Messages
    There are four error messages that might come up when setting up PPPoE on your router. For instructions, click here.

Maybe you are looking for