Need hlp setting up router for gaming

First let me say that im not terribly tech savvy so please remember this if you post a response (thnx) I play Star was Galaxies online and i have wired 2 desktops and one wireless laptop connected to a wrt54gs router and its hooked up yo my modem. my internet works fine. heres the problem awful lag and 10-50 percent packet loss in the game. Gameplay is impossible. I contacted the games tech support and ran a pathping and tracert. after viewing this info the tech support told me that my router firewall was interfering and i should set it up to work with the game. the thing is i dont know how to do that (Doh!) In there response there was mention of configuring ports that the game uses but thats all greek to me. any help would be appreciated or possibly a link to a step by step to doing this thnx

Check this. http://portforward.com/

Similar Messages

Need to set default values for the fields plant and location in ME21N

Hi All,
i need to set default values for the fields plant and location in ME21N tcode.
In accout assignment if we give 'A' then we need to create asset by clicking the Asset tab,there you have the fields plant and location.
How to resolve this?
Thanks in Advance

hi .
i needed to set default strorage location and plant in personal setting in me21n.
i solve it with this way.
go to program SAPLMEPERS in se38.
create new function in output with the sample name :MODULE ZTEST_001 OUTPUT.
in this module write:
if MEPOITEM_PROP-WERKS is INITIAL and MEPOITEM_PROP-LGORT is INITIAL.
MEPOITEM_PROP-WERKS = '1000'.
MEPOITEM_PROP-LGORT = '0032'.
endif.
this is the solution.
best regards.
maryam

What is the best Router for Gaming?

Alright, at the moment I have a "G" wireless router, which I bought it for pure gaming reasons, well I am thinking about upgrading 'cause I am having some lag and poor connections and I want to enhance my connection for online play. I won't lie I am a addicted hardcore gamer, so I need a good router! ^_^
Well I been looking at this WRT330N , which this one interests me a lot!
http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1166859632665&...
I know it's about $200 but I am willing to spend the money if it's worth it! If anyone can share anything about this router or a cheaper and better router please do so!

I started shopping for a wired router to handle a claimed higher speed from my cable provider. I want something that runs at full incoming wire speed. I did not think I would care a lot about special gaming features. One of the techs at work uses the GamerLounge which is made by D-Link and he loves it for gaming. It runs a little over $100. It has a number of features to help automate the setup for gaming and to help debug gaming connection problems. I do not know if Linksys makes anything that is specifically targetted at gaming. You might want to read the various hardware reviews and decide which features you think will be important to you. Linksys has product documentation that describes the products but you will have to understand the terms used in the brochures to decide which device might be best for you. I have a Linksys for wireless support and it is rather slow compared to a wired connection because I run encrypted. If you want to run games on wireless, then published benchmark results may be the number one item on your list. Some routers may have much faster wireless performance than others. Cost will probably be a factor but more expensive does not always mean better. I have a WRT54G V5 and Tom's Hardware has a review discussing some of the serious limitations in V5. I stopped using it as a main router and went back to an old 10 Mbps wired router connected to the cable modem to get better performance. The WRT54G V5 sort of works when used as a wireless access point but Windows file and printer sharing do not work. So ... it all depends on which features are most important to you. Absolute best case is to talk with a friend who has a working setup that they like. Then you can decide if their priorities for choosing features match your priorities.

WRT610N - Need to Set Static IP for Server and Port Forwarding

Does anyone know how I can assign a static IP for my Home Media Server in the WRT610N router? I need to do this because of the settings I need to set for the server in the Single Port Forwarding.
Thanks in advance!

Never mind. I got it.

Inquiry - Best Linksys/Cisco router for Gaming and Media Streaming?

Help! I live in a two bedroom town home and have an old little Belkin router. I'm switching to a Linksys but I need to know which model is best for my home. I have two sons that share a room and they both play XBox live, usually at the same time. I'm usually using the internet or watching a movie on Netflix with my wife. Sometime both while the boys are playing upstairs. I don't need multiple USB ports or gigabit ports. I wouldn't know what to do with them. I just want something faster than what I have now. We have Time Warner Cable's Roadrunner internet service if that helps.

I would recommend EA4500 as it is a high performance router for home entertainment which is ideal for faster streaming of HD video and music plus multiplayer gaming. Please click on the following link to know more features of this router: http://homestore.cisco.com/en-us/Routers/Linksys-EA4500-Dual-Band-N900-Router-with-Gigabit-USB_stcVV...

Need help setting up file for program Ai CS5 Mac

Hello everyone, I am hoping you can help me with something. I am having a 20 page conference program printed through a 3rd party company.The printer sent me back the proof today and on almost every page my artwork is being chopped off.
This is the email sent with the proof today:
" I want you to look at these spreads and tell me if this is how you visualized your finished pages? A lot of your art is being cut off. The finished size is 11x17. You sent pages that were 9x12, so I used them at 100% on the 12x18 press sheet. You only need to provide a 1/8" bleed, not a 1/2". You also have bleeds on the centers of the spreads. Those should not have a bleed. Only the outside 3 edges should bleed.
I had trouble getting all of the art to line up."
Printer Info:
They print on 12/18 trimmed down to 11 x 17 (for full bleed)
Requested bleed: 1/8
They print out of Quark
I was told I can send them individual PDFs and they will paginate them (in order and add page numbers)
I created a file in Ai CS5 with 20 artboards (one for each page of the program) Now, the trim marks should be placed at 1 inch because they are trimming 1 inch from the top and 1 inch from the bottom. The bleed should be 1/8 so 0.125 on the 3 "outside" edges. Is this correct?
I primarily do lay-outs, the person responsible for this project bailed last minute so I am a bit stuck. If I am designing it as individual pages what are the exactly dimensions, bleed, and trim marks needed for each page to be set up correctly for the printer to paginate. Should I also add a .5 margin along the edges as a safe zone or is that not necessary because of the bleed?
Let me know if I didn't provide enough information. I appreciate any help I can get. Thanks in advance!
-d

It is often just simpler to build your pages (or spreads) to the actual size of the press sheet.
I'll assume this is a saddle-stitched booklet.
The press sheets will be 12 x 18 inches.
It will be printed, then, as 11 x 17 printer spreads.
That means it will have a half inch (not a whole inch) between the trims and the press sheet edges on all four sides.
There will be three-eights inch between the bleed and the edges.
(This is crowding things a tad; typically one tries to allow at least a half-inch gripper margin.)
Anyway....
1. Setup the document with twenty 9x12 vertical Artboards, with zero spacing, in two columns. Zero Bleed.
(Often, depending on the nature of the content, I would choose to build such a thing as ten 12 x 18 Artboards, with content already arranged as printing spreads, thus eliminating the need for stripping. But in the following, you'll go ahead and make 20 separate Artboards, abutted in pairs, and treat these as two-page reader spreads, to make layout easy, and to accommodate artwork that may jump the gutter.)
2. Turn on Show Grid. Turn on Snap To Grid.
Rectangle Tool: Click the page. In the dialog, specify a 17 x 11 rectangle. This corresponds to your trim.
Rectangle Tool: Click the page. In the dialog, specify a 17.25 x 11.25 rectangle. This corresponds to your bleed.
Center align the two rectangles to each other, both horizontally and vertically.
3. Zoom in. White Pointer: Snap the upper left corner of the rectangles to the grid at .375 H and .375 V of the top left Artboard.
4. Convert the two rectangles to Guides. (View>Guides>Make)
5. Line Tool: Snapping to the grid, draw your own trim marks at each corner, outboard of the trim. Use .25 pt. stroke weight. Registration color.
6. Unlock Guides. (turn off View>Guides>Lock)
7. Black Pointer: Marquee select around all the trim marks and the two rectangluar Guides.
DoubleClick the Black Pointer. In the resulting Move dialog, enter a vertical movement of 12" and click copy.
Transform Again (Ctrl D) 8 times.
Now you have a set of trim guides, bleed guides, and trim marks on all 10 two-page reader spreads.
8. Create the content as if the pairs of Artboards are facing pages of reader spreads. The top pair are the front and back. The other pairs are sequentially-numbered reading speads. Set up this way, your artwork can jump the gutter when desired. You can put other printer's marks (sep names, etc.) in the bleed area if needed.
9. Save A Copy to PDF with Use Artboards checked. The resulting PDF will contain 9x12 vertical pages. Viewed as spreads in Acrobat, you can see that the pages align.
10. But when they are printed, they will be stripped into two-page printing spreads, ordered like so:
JET

What do I need to set in order for each instance of the step type in the sequence to act individually?

I'm not able to change parameters on one step without it changing the parameters on another instance of the step within the same sequence. Is there something in the step type properties that I need to set to change this?
For instance, I have created a custom step called "Battery PWR" that the user can insert into a sequence, hit the "edit" button, set a control in a GUI to 12V and hit an "Okay" button so that the post-step condition causes the power supply voltage to change. Then, later in the sequence I want the user to be able to insert the same custom step, hit the edit button, set the control to 0V and hit an "Okay" button so that the post-step conditition causes the power supply to go to 0V. The problem is, when the user edits one of the steps, it causes the other step to change to the same value.
I know that this has a simple fix, just can't seem to find it.

I answered my own question. I was reading and writing to a file global instead of the step parameters, so I was basically overwriting my variables each time I edited the step. I'm obviously a novice TestStand user.

Do I need rtexprvalue set to true for a String that will vary from page to page?

Hi I am a newbie to JSP tags. I have done enough reading so far to see
          that if I want an attribute of the tag to be a scriplet ie:
          <foor:bar name="<%=myObj.getName()%>" />
          then the rtexprvalue for this attribute in the TLD needs to be true.
          My question is what if I have an attribute that will not be read from
          a scriplet but will vary from page to page. ie:
          <foo:authorize securityLevel="1"> but on another page it will be
          <foo:authorize securityLevel="3"> etc.. Since many servlet containers
          create only one instance of the tag class and then re-use them from a
          pool do I need to set rtexprvalue to true for an attribute like this
          to make sure the tag reads the correct one as I go from page to page?


          You do not need to set rtexprvalue to true for the situation you describe.
          Laura
          Developer Relations Engineer
          BEA Support
          [email protected] (Mike Lomage) wrote:
          >Hi I am a newbie to JSP tags. I have done enough reading so far to see
          >that if I want an attribute of the tag to be a scriplet ie:
          > <foor:bar name="<%=myObj.getName()%>" />
          >then the rtexprvalue for this attribute in the TLD needs to be true.
          >My question is what if I have an attribute that will not be read from
          >a scriplet but will vary from page to page. ie:
          > <foo:authorize securityLevel="1"> but on another page it will be
          > <foo:authorize securityLevel="3"> etc.. Since many servlet containers
          >create only one instance of the tag class and then re-use them from a
          >pool do I need to set rtexprvalue to true for an attribute like this
          >to make sure the tag reads the correct one as I go from page to page?

What property settings to I need to set in order for VISA Serial Read to read ASCII exactly like the legacy serial read vi?

I have successfully built a vi which communicates with a piece of equipment via the serial port using ASCII characters. I am trying to replace the older versions of Serial Read and Write VIs with the VISA Serial Read and Write VIs. The VISA Write works fine, but the when reading data coming from the "box", the VISA Read VI returns string data with foreign looking characters instead of the usual correct ASCII characters as shown by a dumb terminal which is in parallel with the serial data line. Is there a special property node which needs to be configured on the VISA Serial Read vi, or do I need to set something on the VISA Configure Serial port v
i?
Why aren't the VISA serial vis compatible with the older serial vis?
Thanks...

Usually, garbage characters are an indication of a baud rate or parity mismatch, or maybe a stop bit or number of data bits setting. Make sure that you have configured your port correctly with VISA Configure Serial Port. I have used VISA serial successfully many times.
- tbob
Inventor of the WORM Global

Do you need to use a router for the FIOS tv?

I already have FIOS internet. I have a business account with static IPs and I run some servers which are configured in a particular way that I cannot use a router.
I do want to get FIOS TV as well, but only if I can get it WITHOUT the necessity of using a router for it.
Is that possible?
P.S. I only want non-DVR, Standard Definition, regular TV. I don't want any On-Demand or special TV.

I believe that they can use a NIM-100 instead of a Router to get you FIOS TV Services.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.
If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Need to set up password for airport express with belkin pre-N router

I can't figure out how to set up a WEP password for my wireless network at home. I tried setting it up using the AirPort Admin Utility, but no base station appeared on the menu. I'm using a Belkin Pre-N router. Any recommendations out there?

The AirPort Admin Utility is ONLY for use with Apple's base stations.
You will need to follow the directions in the Belkin's User Guide about using a web browser to change the configuration of the router and enable wireless encryption. If all of your equipment supports WPA, use WPA (with a non-dictionary password) instead of WEP.

Need help setting up MoCa for superior speed for upstair room in house

Hey guys i need some help. I just upgraded my plan to the 50/20 Fios and now i really want that speed upstairs to my gameroom. Before i had the 10/2 plan where wireless was sufficient (i could get 9mpbs download speed wirelessly everywhere i needed internet using the mi424wr)
But now this crappy (no offense ) router is just not sufficient for the 50mbps download speed. Even if my laptop is RIGHT NEXT to the router, i only get max speed of 20 - 23mpbs download. Whereas if im connected via ethernet, i get the full 50+Mbps download speed. For some reason the upload speed is fine at over 20mpbs. (Anyone has any explanation for this? If other 2.4ghz devices were causing interferences, shouldnt the upload speed be affected also?) And Yes, i have changed the channel to 11 (every other wifi network is on 6)
I also have this hawking high gain antenna connected to the router: http://www.newegg.com/Product/Product.aspx?Item=N82E16833164156
In any case i feel that MoCa would be a much cheaper and more reliable approach to achieve better speeds compared to buying a wireless n dual band router & adapter
Currently i have the ONT connect to the WAN Router VIA Coax
I also have Dish network for Tv services with the STB upstairs (same room where i want the Ethernet from MoCa to connect to PC,PS3). Not sure if relevent, but the dish is set up so that my downstair tv has acces to Dish tv VIA the coax connected to the STB upstairs. So ONE STB provides TV upstairs AND TV downstairs with dish services via Coax.
From the various articles i have read, this is my understanding of what i should do but of course im a newbie so i need your suggestions. I should add splitter the coax coming out of the ONT and connect one split to the router and the other split to the wall? then upstairs add a splitter to the coax connection from the wall and split one for dish STB and split one for MoCa actiontec which will then be connect to the internet and i could run ethernet from MoCa actiontec to ps3 and PC.
Is that anywhere even close to a working solution or im just dreaming that it would this easy? lol
Thanks for all the help!

mominn8266 wrote:
The actiontec router is b/g mode only and I've changed it from mixed to g only. I wish they had upgraded my router with the services but nope still have the crappy actiontec router.
If you read my post I've already changed the channel most appropriate for me.
I've also read that post about interferences but if im literally ONE feet away from the router, I should atleast get above 40 mbps download speed. Why is my upload speed above 20mbps but Download speed can't exceed 23mbps?
Is there a possible solution for moca to coexist with dish services? A special splitter to seperate both lines? Or is powerline my only option?
Keep in mind, with Wireless you're limited by the fact that it is also a Half Duplex connection by design (can only send OR receive on a radio, can't do both like you can on Full Duplex Wired connections) which reduces speeds, and also protocol overhead which increases as you add additional devices to an access point.and increase traffic in a broad scale. So, if you're getting 22-25Mbps on Wireless G, that's about all you're going to get from it. 54Mbps is a theoretical limit with the assumption you've cut down all overhead, have a full duplex connection and are not encountering noise.
I recall seeing something on DSLReports about using MoCa with a Satellite TV provider, and it involved a lot of filtering within the coaxial to work. Ideally, you're best using a dedicated line for Coaxial if you're going to use MoCa to cut down on the complexity and risks caused by using a satellite system's coax.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Help setting up router for wireless printer

I recently purchased a wireless printer - but haven't been able to connect to the router. Router is a Linksys wireless G 2.4ghz w/ SecureEasySetup (SES). When I activate the SES button on the router - it will connect with the printer - but the router then re sets itself, my SSID changes to the Linksys default and I loose internet connection.
How can I use SES without the router resetting?

I assume that your wireless printer does not have SES.
When you use SES, the router resets the wireless settings. SES is designed to be used when both devices (router and wireless adapter) both have the SES feature. If only one device has the SES feature, then you cannot use the SES button, and the non-SES device must be setup manually.
Login to your router at 192.168.1.1, and write down the following settings on a piece of paper:
SSID
encryption type (probably WPA)
encryption key (sometimes called Password or Passphrase)
Next, follow the installation procedure for your wireless printer. At some point in the install procedure, it will ask you for the above info.
If you need more help, please state the model and version of your router. Also, please state the make and model of your printer.
Message Edited by toomanydonuts on 04-07-2008 12:25 AM

Need to set static IP for iMac

I have a fairly elaborate home network. I want my iMac to always use the same IP address when it connects because I use it for web development and need it to consistently identify itself on the network. At the same time I need DHCP on for some other devices which connect wirelessly to ask for an IP. I've limited my DHCP server to about 50 addresses from 192.168.1.100 to 192.168.1.150 so there is plenty of room outside that range for me to choose a single IP for this iMac.
The problem is that when I open the Network control panel and choose "Using DHCP with manual address" and enter something like 192.168.1.2 then the iMac forgets its DNS Server, Search Domains, and router and I can't seem to get any DNS on the machine. I can ping the iMac from my other computer and I can ping my local LAN machines from the iMac but from the iMac I cannot ping any domain names like yahoo.com nor can I ping any IP outside my LAN such as 60.180.206.184).
If anyone can explain to me how to set this up, I would greatly appreciate it.

Set your Mac to completely manual configuration and type in the desired IP, subnet mask, router and DNS and you're ready to go. You can also use DHCP with manual address, but in this case most routers won't tell your Mac the correct DNS server, so I'd recommend to set all settings manually.
Björn

WRVS4400N v2: Need help setting up VPN for Mac

I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.
The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.
We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.
At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems.
I have tried just about everything I can think of but have not been able to get this to work. Can someone please help with setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
TIA

Hi,
If you need to establish a client vpn connection with the WRVS4400N, first you need to insure that the modem infront support IPSec Passthrough and that UDP ports 500 and 4500 are forwarded to the WAN IP of WRVS4400N.
On WRVS4400N you have to configure IPSec VPN tunnel, and when configuring IPSecuritas insure that you have the same encryption as on the router.
It could help if you enable the Local logs and see the error message.
You can provide the log output and print screens of the IPSec configuration, also screenshot of configuration of IPsecuritas

Need hlp setting up router for gaming

Similar Messages

Maybe you are looking for