Need info about "sh int dot11Radio" and "sh int dot11Radio stati"

Hello,
Could someone explain me the counters in the 2 following display on an AP (like a AIR-AP1231G)
sh int dot11Radio 0
sh int dot11Radio 0 statistics
SiteR02#sh int dot11Radio 0
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 000f.3415.bf30 (bia 000f.3415.bf30)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:12, output 00:00:12, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
24680 packets input, 3282575 bytes, 0 no buffer
Received 129 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
23427 packets output, 4831674 bytes, 0 underruns
212 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
SiteR02#sh int dot11Radio 0 statistics
DOT11 Statistics (Cumulative Total/Last 5 Seconds):
RECEIVER TRANSMITTER
Host Rx Bytes: 3265473 / 0 Host Tx Bytes: 4338004 / 0
Unicasts Rx: 88699 / 1 Unicasts Tx: 27040 / 0
Unicasts to host: 88699 / 1 Unicasts by host: 23629 / 0
Broadcasts Rx: 0 / 0 Broadcasts Tx: 4601528 / 49
Beacons Rx: 0 / 0 Beacons Tx: 4601528 / 49
Broadcasts to host: 0 / 0 Broadcasts by host: 0 / 0
Multicasts Rx: 0 / 0 Multicasts Tx: 0 / 0
Multicasts to host: 0 / 0 Multicasts by host: 0 / 0
Mgmt Packets Rx: 0 / 0 Mgmt Packets Tx: 3411 / 0
RTS received: 0 / 0 RTS transmitted: 1721 / 0
Duplicate frames: 230 / 0 CTS not received: 1597 / 0
CRC errors: 4303 / 0 Unicast Fragments Tx: 26833 / 0
WEP errors: 0 / 0 Retries: 2540 / 0
Buffer full: 0 / 0 Packets one retry: 435 / 0
Host buffer full: 0 / 0 Packets > 1 retry: 174 / 0
Header CRC errors: 43265 / 0 Protocol defers: 2 / 0
Invalid header: 311 / 0 Energy detect defers: 206 / 0
Length invalid: 0 / 0 Jammer detected: 0 / 0
Incomplete fragments: 0 / 0 Packets aged: 0 / 0
Rx Concats: 0 / 0 Tx Concats: 0 / 0
RATE 2.0 Mbps
RATE 5.5 Mbps
RATE 11.0 Mbps
SiteR02#
Somes counters are displayed on those 2 displays but it is not with the same figure (CRC errors, input, output, broadcast, ...)
Can someone explaines me this ?
regards,

Hello, do you know the formula ?
If I had errors to the "input field -from sh int-" then I don't get the unicats received field in the "sh int stat".
Regards,

Similar Messages

Need info about RH Server 6 and reports

I'm interisted in RH Server 6 but I'm unable to locate much
practical info about it on the Web site, and a call to sales didn't
help. I need to know what I'm getting us into before I contribute
our $2,000. Can anyone provide this information or point me to its
location on the site:
--I have system requirements from the Adobe site, but what is
the "server" and what does installation and setup entail? About how
how long does it take, or how difficult, to achieve operability?
--According to a piece by John Daigle, the server component
should be installed on a Windows server running IIS 5+. Is IIS a
separate software or standart part of Windows server? If separate,
what preparation should that server have before the installation in
addition to installation of IIS?
--I know nothing about security/firewall protocols. We will
have our own and our customer firewalls to navigate. Are the server
setup instructions adequate for setting all that up? Or are
purchasers expected to have sys admins knowledgeable to set that
up? Is that applied to the RH server or the Windows server? if RH
server, how can I get a copy of instructions for my system people
to review?
--Have users found the RH server/RoboEngine reliable, once
it's operable?
--Is it true that the usage reports aren't customizable? Can
additional usage data be specified in the RH server?
--These report summaries are vague--Areas Requiing Help,
Frequently Viewed Content--stating only that repoorts show the
suchandsuch done "most frequently" or "most often." Does that mean
the top 3, 5, 10 or what? Is there a way to track all of that
activity from most to least?
--The summaries of the reports Unanswered Questions and
Frequently Asked Questions say that terms entered in the Search
field are identified. Questions and terms aren't the same in my
book--am I right that it captures anything entered? Can it do the
same for the Index field?
--I saw no RH server under downloads, or maybe missed it.
Correct in guessing that a demo version is not available?
--Is RH server user doc available on the web site? I found
the Getting Started gude, which isn't much use in evaluating the
product.
I have additional questions, but if you can answer these
questions or direct me to answers some of those may be covered.
Thanks,
Mike
Access database.

Hey, Mike!
I found a few things for you. I'm in a hurry, so I'll list
them quickly.
For the Trial, go to the Adobe downloads page
http://www.adobe.com/downloads/
Then select RoboHelp Server 6 from the dropdown list. You
will be asked to register (free) if you haven't already. When you
arrive at the download page make sure you note the Trial Serial #
To make it easier for you, its:
1336-1033-2628-5062-0993-4570
You can also find a RoboHelp Server 6 Getting Started Guide
here
http://www.adobe.com/support/robohelp/downloads/getting_started_rh6_server.pdf
You were asking about IIS. Yes. As Colum says, this comes
with virtually any version of Windows Server (or Windows XP
Professional). However, you must install and configure it. I am not
an IT or web administrator so it took me a while to learn, but
amazingly I got it to work if you're patient and follow the steps.
(I'm speaking of both IIS and Robohelp Server) Clearly IIS
configuration is not a trivial thing and it is assumed that an
author would have help and cooperation from the IT or Web Admin
folks.
As for customizing reports. At present, the existing reports
are the only ones offered. Since these reports are generated from a
database (Access, SQL Server or Oracle) I would think (haven't done
it myself) that someone familiar with database adminstration could
open the DB (after a backup that is) and be more creative with
generating customized reports.
You are right that the "Question" does in fact mean any
search term or phrase that an end user puts in the search field.
This is the string that is stored and reported as a question. In
discussing this with the Adobe team at STC last month, they agreed
that this was definitely a holdover from the legacy software and is
due for a change sometime in the future.
To answer your other question, text entered in the Index
field is not stored in the database, only the search term field.
Since taking on the old legacy product from eHelp and
Macromedia, Adobe is focusing most of its attention on beefing up
the client authoring app for the next version (Adobe RoboHelp 7).
My assumption is that they are keen on improving the RoboHelp
Server as well. I have passed along many feature requests along the
lines you seem to suggest and hopefully the server will evolve
along with the client app.
Even with its limitations, my clients tell me RoboHelp Server
provides very useful feedback to help them improve their knowledge
base content to make it more helpful and responsive to users needs.
They also like the searchability of PDF, Word, PPT and Excel as
well...something which plain WebHelp without the RoboHelp Server
does not do.
I probably didn't get to everything, but hope this helps.
John

I need info about CL_XML_DOCUMENT

Hi to all,
I need info about the class CL_XML_DOCUMENT and his methods.
I only have seen information of a few methods.
Where can I find more information and examples of use about this class?

Hi,
This question is already answered before in this forum, check out the below link -
Information about CL_XML_DOCUMENT
Hope this helps.

Need Info about BW CRM Analytics

Hi all,
Guys,
Please help me out...
I need Info about BW with CRM Analytics
What are the core areas where data's are extracted for CRM to BW
What will be the Interview question related to BW CRM Analytics
If possible if u have any docs kindly email me at [email protected]
Thanks in Advance.
Jaffer Ali.S

Dear Jaffer Ali S.,
The following types of analyses can be carried out:
CRM Lead Analysis
Use the InfoCube CRM Lead Management (Technical Name: 0MKTG_C01) for reporting.
The Lead Management InfoCube contains all the characteristics and data used for the administration of leads. This InfoCube enables you to execute the following standard queries available in SAP BW:
Channel Analysis
Efficiency Reporting
Historical Evaluation
Lost Leads
Channel Management: Top-n Lost Leads (Current Year)
CRM Activities Analysis
Use the InfoCube CRM Activities (Technical Name 0CSAL_C01) for reporting.
The InfoCube for activities in CRM provides the data basis for evaluating business activities undertaken by your employees. It provides you with information about how much time is being spent on contacting the customer, whether customers actively seek out contact with your company and how intensively your employees look after your customers. It delivers data for queries such as:
Intensity of customer care
Activity History
Success/failure analysis
Customer Interaction Center (CIC)
Activate the InfoCube Interactive Scripting Evaluation (IC WinClient) 0CRM_CIC1.
Interactive Scripting Evaluation (IC WinClient)
This InfoCube provides the data base for the interactive scripting evaluation. It supplies the data to the Interaction Center (IC): Interactive Scripting Evaluation query.
Opportunities Analysis
Activate InfoCube 0CRM_C04 - Opportunities.
The CRM Opportunities InfoCube contains all the characteristics and data used for the opportunities analyses.
Sales Order Complaints Analysis
Activate InfoCube Complaints (Technical name: 0CSAL_C09).
You can carry out the complaint analysis on a daily, monthly, weekly or a quarterly basis. The analysis can be done in relation to CRM Service Organization, CRM Sales Organization, CRM Product, and Sold-To Party.
Service Qualtiy Analysis
Activate the MultiProvider 0CSRVMC04 - CRM Service - Orders and Confirmations with Complaints.
The MultiProvider 0CSRVMC04 - CRM Service - Orders and Confirmations with Complaints gets the data from the following ODS objects for analyses in various queries:
0CRM_PROI - Orders: Item Data
0CRM_COI - Controlling (Item Data)
0CRM_CNFI - Confirmations (Item Data)
0CRM_COMP - CRM Complaints (Items)
Let me know if you need further help.
Reward points if it helps.
Regards,
Naveen.

Need info about programming with InCopy

Hi,
I have a client who has stored thousands of InCopy documents with valid styles applied to segments of it.
Now my requirement is to create a template which has XML tag -> Style mapping.
Considering that template, I am suppose to open all the InCopy documents, apply that Tag -> Style mapping to it and then convert all of them to XML and persist the data in DB.
Is there a programmatic way as to apply XML tags to a document based on the styles used?
Please educate. I am a complete newbie to InCopy - so please bare with my questions,
Thank you, Appreciate your help.
Regards,
Chintan

You could download and deploy "struts-example.war" from apache website.
          [That Struts 1.0.2 I think.]
          ---Nam
          Jordy wrote:
          > I want to find out how to use it with WL 7.0. Would anyone give me any info about it? :) Thanks
          And God said
          Let there be numbers
          And there were numbers.
          Odd and even created he them,
          He said to them be fruitful and multiply,
          And he commanded them to keep the laws of induction.
          [Bill Taylor [email protected]]
          [nam_nguyen.vcf]

Need Info about using Strut with WL 7.0

I want to find out how to use it with WL 7.0. Would anyone give me any info about it? :) Thanks


You could download and deploy "struts-example.war" from apache website.
          [That Struts 1.0.2 I think.]
          ---Nam
          Jordy wrote:
          > I want to find out how to use it with WL 7.0. Would anyone give me any info about it? :) Thanks
          And God said
          Let there be numbers
          And there were numbers.
          Odd and even created he them,
          He said to them be fruitful and multiply,
          And he commanded them to keep the laws of induction.
          [Bill Taylor [email protected]]
          [nam_nguyen.vcf]

Needed info about io devices and cpu without using prtdiag

Hi
I need to collect info about io devices and cpu. but i cannot use prtdiag.
is there any way to collect this information on solaris machine....
may any available c APIs
Thanks in advance.
Nagesh

yep.... prtconf -vp | grep <wot u r looking 4>

Need info about 2006s(5.1/5.2)

Hi,
Need some info about the new product 2006s (5.1/5.2), what are the new features, whats new on the technology side, what skill sets will be required for these products.
is GUI/SPRO still there in the new products or some new config tool is being introduced.
any info is helpful, pls share usefull docs, links to SAP docs.
pls email me at [email protected]
thanks
RH

Hi rh,
The theory is a new interface, replace gui an pcui. The configuration is based in business roles and this configuration is with spro customizing. Web Client tecnology based and the most important news is a new configuration tool to modify the layout.
Regards.
Manuel

Need info about GN_INVOICE_CREATE

Hi experts!
I need to create Credit / Debit memo invoices in my Z program, so I decided to use GN_INVOICE_CREATE for this, but can not find info about parametres of this FM....
could anyone explaine how to use this FM or maybe someone has a peace of sample code of using this FM?
Helpful answers and advices will be rewarded.
Here is this FM:
CALL FUNCTION 'GN_INVOICE_CREATE'
EXPORTING
    DELIVERY_DATE           =
    INVOICE_DATE              =
    INVOICE_TYPE              =
    PRICING_DATE              =
    VBSK_I                          =
    WITH_POSTING              =
    CALLER_TYPE               =
    I_WITHOUT_REFRESH    =
    ID_NO_ENQUEUE           =
    ID_KVORG                      =
    ID_NO_DIALOG                =
    ID_NEW_CANCELLATION =
IMPORTING
    VBSK_E                           =
TABLES
    XKOMFK                           =
    XKOMFKGN                      =
    XKOMFKKO                      =
XKOMFKTX                         =
    XKOMV                             =
    XTHEAD                            =
    XVBFS                              =
    XVBPA                              =
    XVBRK                              =
    XVBRP                              =
    XVBSS                              =
XKOMFKZM                         =
SUCCESS_DOC_OUT          =          .

Hi Mindaugas,
check BAPIinvoice in SE37, e, here u cannt directly make use of GN_invoice_create, Bcos here u dont have condition records data.
so search in SE37 or Tcode BAPI , here u can get FMs along with Documentations.
Regards
Peram

Need info about the parameter _FIX_CONTROL in a BW environment

Hi ,
I have done some research about the parameter FIXCONTROL and went through the SAP note 1165319.
We have a task at hand where SAP has recommended a new value to be added to this parameter in a BW production environment.
Now in the above note there are an entire set of values which this parameter can take up.
I have understood to some extent that this has to do with this Fixes if case of any issues.
last month we have upgraded the oracle version of the database from 10.2.0.2 to 10.2.0.4.
Can anyone help me in understanding what this MergeFix is all about?
I need to better understand this concept.
Thank you.
Regards,
Hari Kishan.

Hello,
still not sure if I fully understood your question; but the recommended approach regarding patches is:
1) Apply all the interim patches recommended by SAP. For Oracle 10.2.0.4 these will those from SAP note 1137346. The merge fix from SAP note also 1165319 is mentioneded there.
And by the way, SAP note 1137346 is updated about once a month; new patches may be added, old ones may be removed. SAP recommends to follow accordingly; but if there aren't any problems, you might want to you keep your current state for a longer period.
2) Read all the SAP notes mentioned there. You may have to do additional tasks like setting Oracle parameters, FIXCONTROL or others. The value you have to set now may or may not be mentioned in one of these notes, I can't know.
3) If you encounter some problem, first search in SAP notes, or if necessary open a support call with SAP. You may then have to apply additional patches and set addtional values for FIXCONTROL.
And yes, this way the list of required patches may become specific to each customer, as customer requirements are specific.
But it would be difficult to find the exact list of needed patches in advance.
I think a BW consultant who is familiar with Oracle installations will tell you something similar. One who is very experienced in your scenario might also be able to recommend additional patches in advance.
regards

Need Info About Document Management System

Hi All,
I need information about Document Management system.
How it is linked with KM
Thanks
Arun

Hi Arun,
DMS is available in R/3 Systems as a individual module and can be linked with KM using DMS Connector for KM. Find the links below..
Check this out...
<a href="http://help.sap.com/saphelp_nw04/helpdata/en/30/08a037b9e62417e10000009b38f889/frameset.htm">DMS</a>
<a href="https://www.sdn.sap.com/irj/sdn/thread?threadID=26682">Thread 1</a>
<a href="https://www.sdn.sap.com/irj/sdn/thread?threadID=235959">Thread 2</a>
Hope this helps.
Regards,
Venkat.

Need info regarding Oracle UCM Accounts and Security Groups behaviour

Need information regarding Oracle UCM Accounts and Security Groups behaviour.
Oracle UCM version: 11.1.1.5.0
Steps:
1. Log in with "weblogic" user and created a content with id "content1"
2. Applied "@acc1(R)" and "TestGroup1" to the cotent created in step 1
3. Log out
4. Log in as "acc1user1", the user is not able to see the "content1"
5. Log out
6. Log in as "role1user1", the user is not able to see the "content1"
Account and Group information:
1. User "acc1user1" is part of "@acc1(R)"
2. User "role1user1" is part of "role1(R)" and is mapped to "TestGroup1" in UCM
Expected:
Both "acc1user1" and "role1user1" should be able to see "content1" as they have at least Read permission.
Please help me understand why the users are not able to see the content.

ACLs, like Accounts, are optional security setting which may add on some extra functionality to mandatory security groups. Likewise, the resulting permission is taken as an intersection of SG and ACLs.
But in the second part the number of set of users is huge (approx say 600)I don't get this completely. Does this mean that those "sets of users" (users who see the same data) are distinct and that there is 600 of such groups?
If you read thoroughly the manual I sent earlier, there is a recommendation that there should be maximum 50 security groups, and you should use accounts, should this number be exceeded. This means you could have all the documents in one security group (and have one common role with Read permission), but combine it with accounts. ACLs are not a good choice here - their performance and manageability is much worse than of accounts. ACLs are primarily used if you expect security settings to change during the lifetime (e.g. a project manager adds temporarily rights to access an item to another user, and revokes it when the user finishes his or her work).
Note that accounts as well as permissions of users within accounts can also be mapped externally (from LDAP/AD) and it usually follows some kind of org chart.
I'd feel more comfortable not to speak about users, security groups, roles, etc., but about some real-life objects and scenarios.

Want more info about optimizing battery lifespan and performance

I have read Apple Support's basic article on iPhone battery charging, but it doesnt answer all of my questions. i am kind of a fanatic about maintaining the health and longevity of my battery. I usually run it down to 3% or less before plugging in, then charge it all the way up. This creates some inconvenience, but after one year, my iPhone 5 battery is still performing much better than any previous iPhone ever did. Here are a few questions I have:
1. Is it really neccessary to wait for the battery to drop to 3%, or could I charge it after it goes below 20%, if it is more convenient?
2. Is there any harm in charging to less than 100% if I am in a hurry?
3. If I regularly plugged it in at over 50%, would it develop a memory and hold less charge?
4. What effect, if any, do Mophie Juick Packs have on iPhone battery health (I just got one)?
If there were no memory issues, the most convenient thing to do would be to plug it in every night at bedtime. Any knowledgable commentary would be welcome.

There's a few aspects to this - and such several "correct" answers.
First, what exactly will you be doing? Are you just editing or will there be vfx/color grading etc? If it is the latter, and you're in SD, I'd personally go with uncompressed 10-bit. The files will be large, but it will be worth it if you do a lot of processing.
ProRes files will be much smaller, and still look very good, but may not hold up as well to heavy processing.
Not sure what you mean with #2... what other codec(s) are you looking at. Saying it is "unnecessary for SD" is an interesting comment - depends on what you want to do with the footage.
Some info about ProRes (and uncompressed) bitrates:
http://www.appleinsider.com/articles/07/04/18/acloser_look_at_apples_new_prores_422_videoformat.html
http://www.apple.com/finalcutstudio/finalcutpro/apple-prores.html
http://sportsvideo.org/main/blog/2009/08/11/apple-final-cut-prores-lowers-bitrat e/
http://documentation.apple.com/en/finalcutpro/professionalformatsandworkflows/in dex.html#chapter=10%26section=1%26tasks=true

Need info about nvidia graphics card supported with premiere pro cs5

Hi
I need information about nvidia graphics card supported with premiere pro cs5
If I have a computer(portable) with this video card or graphics card :
nVIDIA® GeForce™ GTX 285M with 1GB DDR3 Video Memory available in Single or Dual (SLi) Configurations
Microsoft® DirectX® 10 Compatible
is it going to support MPE in premiere pro cs5?
Regards,
Vinay

To be clear:
You asked about supported cards. Here is a list of supported cards. Others on this thread are telling you how to make an unsupported card function to some degree using a method that is not advocated by Adobe.

Need information about SAP EM Configuration and Implementation

Hi,
I am new to SAP EM.I need to do Configuration for EM and Procurement visibility process.
Please provide some information on configuration of EM with examples.
Thanks,
Prasuna.

Hi
There is wealth of information available on the [Service Marketplace |https://websmp107.sap-ag.de/scm]on the standard visibility scenarios which will probably get you started. Procurement visibility scenario is one of the them and have documentations.
There are couple of points which are worth knowing that SAP Event Management
- requires configuration in both application system (ECC) and SAP EM system (SCM)
- good understanding of the function module (extractors) for sending and posting events
- well thought supply chain events (design) business would like to monitor and manage
- reactions to both expected and unexpected events (follow-up activities)
The other resource available are [SAP PRESS technical book |http://www.sap-press.com/products/Implementing-and-Configuring-SAP-Event-Management.html] and [published case studies |http://www.scmexpertonline.com/article.cfm?session=&id=4804] on the SAP EM Procurement visibility scenario.
Cheers
Sandeep Pradhan

Need info about "sh int dot11Radio" and "sh int dot11Radio stati"

Similar Messages

Maybe you are looking for