Need info on replacing HP e9180t motherboard

I posted earlier on having a problem with my e9180t.  I found out the IPMTB-TK motherboard is the problem.  So, what is the best replacement to use, also, where can I find instructions on how to take out the old one?

Refer the attachment which might give yout the missing steps...
I am an HP employee.
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***
Attachments:
To replace the motherboard.doc ‏117 KB

Similar Messages

  • Is it necessary to replace the entire motherboard if the fan needs to be changed?

    I recently sent in my MacBook pro (mid-2009) to a authorized service provider for repairs. I brought it in because of those weird noises coming from inside the MacBook and that it became very hot after running for awhile. The technician ran a simple diagnostic and it seemed to be a problem with the fan, and he advised me it would involve replacing the entire motherboard should there be a need to replace the fan. The question is that really necessary? I have visited a few forums and most indicated only the fan needs to be replaced. Does anyone have any comments on this? I am hoping I have not been taken for a ride.

    fak838- Here is an instructional guide on how to replace the fan on a Mid 2009 MBP 13".  No mention of a motherboard replacement as a part of the process is mentioned.: http://www.ifixit.com/Guide/Installing-MacBook-Pro-13-Inch-Unibody-Mid-2009-Fan/ 1338/1.  If you mac is a different size,here is the 15" version and for replacement of both the right and left fans, motherboard replacement is not indicated as being necessary in order to replace the fans: http://www.ifixit.com/Device/MacBook_Pro_15%22_Unibody_Mid_2009

  • Replacement Needed. This iphone is not able to complete the activation process and needs to be replaced. Please visit your nearest apple store or authorized service center.

    Probably will never ever think of buying a locked phone from AT&T cause its one of the worst system integrations ever that these companies could think of.
    The entire problem started when I put in a request with at&t to unlock my iphone 4s (ios7) which did get approved. I performed the entire instructions they asked me to do, which is to backup and restore. After doing those instructions my iphone gave me an error message below
    The SIM card inserted in this iPhone does not appear to be supported.
    The SIM card that you currently installed in this iPhone is from a carrier that is not supported under the activation policy that is currently assigned by the activation server. This is not a hardware issue with the iPhone. Please insert another SIM card from a supported carrier or request that this iPhone be unlocked by your carrier. Please contact Apple for more information.
    Basically saying that at&t hasn't still unlocked the iphone which a really helpful apple executive was able to confirm. I initiated another unlock process from at&t in order to unlock the iphone, just to be sure that its not something wrong from my end. The nice at&t lady stayed on chat with me to unlock the iphone step my step while I was calling the apple tech too. And the apple tech confirmed again that the iphone is locked to at&t.
    Now, just a few minutes ago I tried another restore to see if any progress is being made and to my surprise I got an error message saying
    Replacement Needed. This iphone is not able to complete the activation process and needs to be replaced. Please visit your nearest apple store or authorized service center.
    I feel like I am just going around these two different "money hogger" companies which set certain rules and regulations to screw a regular phone buyer. I purchased this iphone in USA and trying to unlock in India, is it really this hard to simply unlock a device.
    For now I am going to try to call a apple office in india (apprently we don't have very many out here) and see if they can help me. But any other assistance regarding unlocking an iphone 4s would be helpful. I have however, tried checking IMEI.info, called up apple, talked to at&t (which always say go talk to apple) I do have a case number from apple as well in case an apple executive reads this discussion forum (case number: 566383594)
    Thanks

    You got a confirmation from AT&T that it was authorized. Is this correct? - Yes i did get an email authorization on the 21st.
    Then you connected the phone to a computer with the latest version of iTunes installed. You clicked on the phone's name in iTunes, then clicked "Backup Now". - Yes
    When that finished you clicked "Restore iPhone" (NOT "Restore Backup") - Yes
    Are you with me so far? - Yes.
    And @ Varjak is right that after the 3rd restore I get the replacement error. 
    Plus I have NEVER jailbroken the iPhone. To give you another update, I spoke to a really nice apple tech in India who was atleast able to get me out of the replacement error by doing a recovery mode option. However, the lastest restore still gives me the same error
    The SIM card inserted in this iPhone does not appear to be supported.
    The SIM card that you currently installed in this iPhone is from a carrier that is not supported under the activation policy that is currently assigned by the activation server. This is not a hardware issue with the iPhone. Please insert another SIM card from a supported carrier or request that this iPhone be unlocked by your carrier. Please contact Apple for more information.
    Message was edited by: jabgars

  • Corrupt hard drive needs to be replaced?

    I WAS TOLD BY BEST BUY GEEK SQUAD WHEN I TOOK MY LAPTOP TO THEM A FEW MONTHS AGO THAT MY HARD DRIVE IS CORRUPTED AND I NEED TO REPLACED IT. IS IT TRUE THAT I HAVE TO REPLACED MY HARD DRIVE AND THEN USE MY RECOVERY DISC WHICH I DON'T HAVE TO FIX THE PROBLEM?

    Hi:
    It depends on what the hard drive diagnostics test reported, as to whether or not it needs to be replaced, or if only the operating system needs to be restored.
    You can probably order recovery disks from HP for your notebook, but without knowing the full model number of it, I would not be able to provide any further details.
    If you do not know the full model number of your notebook, then please read the guide at the link below for how to find out that info.
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00033108&lc=en&cc=us&dlc=en

  • Help need info

    i replaced my old hard drive with a new  one  i need to know if i can do it with a cable usb? it a intrunal i need info on how to do this i know it can be done
    what cable do i need and how to i do it?

    Why not just call Steve Ballmer? I can see from your post history that you know him.
    If you replaced it, you shouldn't need a new IDE or SATA cable.

  • Hard drive on macbook pro 13' needs to be replaced, any suggestions on which one as per today? mine was since 2009.

    Hello
    i was told my HD needs to be replaced as it is damaged (no exact explanation here from Apple but nevermind)....so is there a specific HD to avoid to be installed? i bought my mac in october 2009. Thank you for the advice.

    Thank you both, really useful info.My mac is for now 250 gb 5400rpm. I have to say this 250gb is enough for me.
    I was offered as below for replacing the hard drive.
    Would be Samsung a good option? hybrid one? for sure I take note no Western. And I would go indeed for 7200 rpm as suggested by you too.
    New hard drives starting with the most expensive:
    SSD hard drive instead of regular winchester:
    120 GB Samsung SSD meghajtó 28 000Ft +afa
    250 GB Samsung SSD meghajtó 42 000Ft +áfa
          -    winchesterek:
    320GB 5400rpm winchester  20 000Ft+áfa
    500GB 5400rpm winchester  22 000Ft+áfa
    1000GB 5400rpm winchester  27 000Ft+áfa
    Faster winchesters with 7200 rpm ( a bit quicker than 5400rpm):
    320GB 7200rpm winchester  24 000Ft+áfa
    500GB 7200rpm winchester  26 000Ft+áfa
    * Hybrid Winchester:
    It includes a 500 GB Winchester and a 8 GB SSD hard drive (hence hybrid ), combines the speed of SSD and the speed of the Winchester (it takes cca 30 sec to start the laptop instead of 90 seconds):
    500GB 7200rpm winchester +8GB SSD  34 000Ft+áfa
    Also since my date needs to be saved/recovered by data saving company, I was suggested to bring an external HD.
    Any suggestion on external HD to buy? or not to buy? then at least i will have a copy before getting new hard drive for my mac.
    Thank you

  • Printer message says, "optical photoconductor will need to be replaced soon".

    I have a HP color laserJet 2840. I am getting the message that my "optical photoconductor will need to be replaced soon." The message is not on my printer window but on my printer info that I pulled up on my computer. 
    This question was solved.
    View Solution.

    I have the same problem with my Color Laserjet 2500. Although the words "optical photoconductor" do not exist in the printer's manual, I just discovered that the imaging drum is also called the optical photoconductor. I hope that's helpful.

  • Replacing imac 333 motherboard...help!

    I purchased an iMac 333 for my mother last month and we just found out that the ethernet port is shot after many attempts of trying to go online. The guy I purchased it from told me that the motherboard needed to be replaced. Could someone give me tips on how to replace it myself or point me in the direction of a site that can help me out. Thanks.
    12" PowerBook G4 w/SuperDrive   Mac OS X (10.4.4)  

    Welcome to the iMac CRT Networking board,
    Not really a network topic, but this might help.
    Rick

  • HP Envy 17 1050e HDMI port broken - do I have to replace the whole motherboard?

    The HDMI port on my hp envy one day just fell out - I assume it has been pulled or pushed too hard. It looks like the ports are directly connected to the motherboard, can I somehow just stick it on again or buy it as a separate part or do I have replace the whole motherboard to make it work again? Any instructions are very wellcome!
    Thanks!

    You need to bring that to a computer shop that has someone with a soldering station and good soldering skills.  The will also have to ascertain how much damage was done to the mother board.  Those things just don't fall out.  It have to be ripped out. If the pins just sheared, a new piece could be soldered back in after they unsolder the parts of the pins left behind.  If the mother board is damaged in that area, you may not be able to use HDMI. It will depend on them being able to repair the broken traces and you would have to be in a good shop for them to do that.  That may be time to search eBay.
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

  • Hi, recently my MacBook pro 13" late 2011 model stopped powering up. I did looked into the internet they were saying memory problem. when I took it to Apple service center they said mother board needs to be replaced. could anyone help me please?

    my late 2011 MacBook pro stopped powering up. Service people are saying motherboard needs to be replaced. The worst part is motherboard cost is 2/3 of the laptop cost. Could anyone help me to understand the issue please?

    The issue is simple. Your Mac computer has failed because of a faulty Logic, Mother, board. Happens all the time with many make and model notebooks
    Yes Apple Mac computers, even though more expensive than most any other brand, have these problems just like all the rest.
    Only thing you can do is either pay to have the logic board changed or buy a new computer.

  • MOVED: Need info on windows xp pro purchase

    This topic has been moved to Operating Systems.
    Need info on windows xp pro purchase

    A Windows 8.1 Product Key will not work for a Windows XP install.
    Please do not read this sentence. Please ignore the previous sentence.
    Hi,
    We wont use the Win 8.1 Product Key - We will Purchase new Windows 8.1 License for the fourth PC but install our copy of Win XP on the machine (we have only 3 License that we used for the older 3 machines).
    Carey's reply only speaks to the technical aspects of installing a dual boot environment.  It says nothing about licensing which is what I think you are asking about.  I do not believe that you can purchase a Windows 8.1 License and apply it to a
    Windows XP install.  You need to enter in the Product Key when the OS is installed and I seriously doubt that the XP install will accept the 8.1 Key.  If you don't have a 4th key for XP you won't be able to have a legal copy installed.
    Please do not read this sentence. Please ignore the previous sentence.

  • My 2008 Macbook froze (though iTunes kept playing), and wouldn't turn off, so I had to take the battery out to turn it off. However, it is not turning on. The battery was in condition of "needs to be replaced soon", but is there any way I can start it up?

    Last night, I was listening to a podcast, and my Mac froze. The mouse would not work, and neither would any of the buttons, but the podcast continued to play as if nothing was wrong.  I tried to turn it off and on with the power button, but it did not respond.  I had to take out the battery and put it back in.
    However, the Mac is no longer starting up. The battery was old, and needed to be replaced soon.  Because I have three important exams next week, and I have all of my notes on that device, I was wondering if there was a way to get the Macbook to work again, without taking the time to replace the battery? I've tried plugging it in, but it doesn't seem to charge.
    Thanks!

    Does the unit not run on the charger alone? (take the battery out and plug it in.)
    Try an SMC Reset
    http://support.apple.com/kb/ht3964

  • Error while navigating planning 9.3.1 through workspace/ need info on cpx,

    Hi all
    Hey I installed the planning 9.3.1 and also I created the application name, using planning address. but the problem is I am unable to navigate through workspace. I am getting three dialog boxes....
    " invalid or could not find module configuration"
    "Required application module hyperioin planning app wizard is not configured.please contact your administrator"
    " Communication error"
    I'm able to see the application name in projects of shared services. Can any one face the same situation , and also I need info regarding how to initialize modules of capx and wfp.
    regards
    M.V

    Hi,
    If you did a standard install then it should be running on port 19000 as well.
    I take it workspace is working fine on port 19000
    http://<hostname>:19000/HyperionPlanning/LogOn.jsp
    ^ this will be your workspace servername..
    When you run the configuration utility for Reporting and Analysis and the section "Configure Web Server", this is where you set up the Apache Server for workspace, there is an option for "Planning", this should be ticked and the correct planning server entered as it will default to the workspace server.
    The apache server redirects requests on the standard workspace port 19000 to the correct server and port, so for planning it redirects to the planning server and port 8300.
    Cheers
    John

  • Need Help in Replacement of Function Modules

    Hello all,
    I am working on Upgrade project from ECC 5.0 to ECC 6.0. I am facing problems for Replacement of two Obsolete Function Modules. Please give me a solution. FM's  are as follows.
    1) SET_AUTHORITY : This FM is obsolete in ECC 6.0 and there is not alternative FM present in help.sap.com or any other web portal.
    2) WS_QUERY : Here as per my knowledge we use class CL_GUI_FRONTEND_SERVICES and methods FILE_EXIST or DIRECTORY_EXIST as per the parameters in old FM. For parameter 'FS' we use 'FILE_EXIST' and 'DS' we use 'DIRECTORY EXIST'.
    But in our program prev. FM has parameter 'OS' i.e. Operating System.
    But there is not method called 'OS EXIST' or similar. Please suggest suitable method.
    Thanking you all in anticipation.
    Best Regards,
    Harish

    Hi Harish,
                       I too could not find any replacement for SET_AUTHORITY
    Obsolete Modules can be used in newer versions, but it is not supported by SAP in case of any technical issues.If you still need a replacement, you can replace it by the source code in the FM SET_AUTHORITY itself and modify according to your needs.
    Below is the source code of FM SET_AUTHORITY, so you can modify it according to your requirement.
      DATA: l_actvt  TYPE tact-actvt,
            l_hier   TYPE STANDARD TABLE OF sethier WITH HEADER LINE.
      CASE action.
        WHEN 'A    '.
          l_actvt = activity-add.
        WHEN 'C    '.
          l_actvt = activity-modify.
        WHEN 'D    '.
          l_actvt = activity-display.
        WHEN 'E    '.
          l_actvt = activity-delete.
        WHEN 'UD   '.
          l_actvt = activity-display.
      ENDCASE.
      CALL FUNCTION 'G_SET_TREE_IMPORT'
           EXPORTING
                no_descriptions  = 'X'
                no_rw_info       = 'X'
                setid            = set
                tabname          = table
                root_header_only = 'X'
           TABLES
                set_hierarchy    = l_hier
           EXCEPTIONS
                OTHERS           = 0.
      READ TABLE l_hier INDEX 1.
      IF sy-subrc <> 0.
        CLEAR l_hier.
        l_hier-shortname = set.
      ENDIF.
      CALL FUNCTION 'G_SET_AUTHORITY_CHECK'
           EXPORTING
                actvt  = l_actvt
                authgr = l_hier-authgr
           EXCEPTIONS
                OTHERS = 1.
      IF sy-subrc <> 0.
        CASE action.
          WHEN 'A    '.
            MESSAGE e827 WITH l_hier-shortname RAISING no_authority.
          WHEN 'C    '.
            MESSAGE e828 WITH l_hier-shortname RAISING no_authority.
          WHEN 'D    '.
            MESSAGE e829 WITH l_hier-shortname RAISING no_authority.
          WHEN 'E    '.
            MESSAGE e830 WITH l_hier-shortname RAISING no_authority.
          WHEN 'UD   '.
            MESSAGE e831 WITH l_hier-shortname RAISING no_authority.
        ENDCASE.
      ENDIF.
    If you need help in replacing in the above source code, please post your code here so that I can help you in modifying accordingly.
    Regards,
    Vasuki

  • My hard drive needed to be replaced for my iMac. When I move the photos from my portable hard drive back into iPhoto, the pictures show up small and I can't adjust them. How do I fix the pictures so they are full size again?

    My hard drive needed to be replaced on my iMac. When I try to move the photos from my portable hard drive back onto the Mac, they are small and can't be edited or made any larger. How can I fix them?

    YOu restore your phone from your icloud backup.
    http://support.apple.com/kb/HT1766

Maybe you are looking for