Need info regarding light weight AP 1042 registration

hi ,
I ordered controller 2504 and will arive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Managment IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
default-router 10.10.3.1
option 60 ascii "Cisco AP c1040"
option 43 hex f104.0a0a.1610
dns-server 10.10.3.1
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
default-router 10.10.3.1
option 60 ascii "Cisco AP c1040"
option 43 hex f104.0a0a.1610
dns-server 10.10.3.1
port-channel load-balance src-dst-ip
interface range gig 2/38 - 41
switchport
channel-group 13 mode on
no shutdown
interface port-channel 13
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 1
switchport trunk allowed vlan 1,122,103,113,1002 - 1005
switchport mode trunk
no shutdown
Regards
Naray

Hi Naray,
I just setup my wireless network with 2504 WLC and 1142 AP's. I don't have to define option 43 or 60 for DHCP i think you need to do this if you have more than one dhcp scope or if you create new scope for wireless.
In my case i use my old dhcp scope and i just configured wlc with external dhcp and AP joined straight away. One issue i had was AP wasn't joinging the WLC because of wronge time and date on wlc. Its prety straight forward hope it goes well for you.

Similar Messages

Need info regarding infotype 0017.

Dear Experts,
I am new to Travel Management.
In infotype 0017, I need information regarding RGrp M/A Statutory, RGrp M/A Enterprise,EE Grp Expense Type and EE Group Travel Mgt fields.
I verified few config documents of Travel Management but could not understood the applicability of the above fields. Please help me in this regard.
Points could be awarded accordingly.
Regards,
Dolly

Hi,
RGrp M/A Statutory-> Identifies a reimbursement group for meals/accommodations for which the same statutory or pay scale trip provisions for meals and accommodations are valid
A reimbursement group is a grouping of employees for whom the same trip provisions are valid. The reimbursement group is specialized by the trip expense category.
A reimbursement group for meals/accommodations is a reimbursement group for which the same trip provisions for meals/accommodations are valid.
The reimbursement group for meals/accommodations is specialized as to whether it is needed to represent statutory/pay scale or enterprise- specific trip provisions.
Example
Trip costs levels A, B, C according to German Travel Expense Statutes
Grouping of employees according to pay scale groups
RGrp M/A Enterprise-> Identifies a reimbursement group for meals/accommodations for which the same enterprise-specific trip provisions for meals and accommodations are valid
A reimbursement group is a grouping of employees for whom the same trip provisions are valid. The reimbursement group is specialized by the trip expense category.
A reimbursement group for meals/accommodations is a reimbursement group for which the same trip provisions for meals/accommodations are valid.
The reimbursement group for meals/accommodations is specialized as to whether it is needed to represent statutory/pay scale or enterprise- specific trip provisions.
Example
Members of the Executive Board
Managers
Salaried employees
Industrial workers
EE Grp Expense Type -> An employee grouping for trip expense type is a classification of employees for whom these trip expense types are permissible.
Example
- Executive Board
- executive employee
EE Group Travel Mgt fields-> An employee grouping for Business Trip Management is a classification of employees designed to fulfill the purposes of Business Trip Management.
Example
- employee
- mailman
- other
Regards,
Pramitha.

Need info regarding Oracle UCM Accounts and Security Groups behaviour

Need information regarding Oracle UCM Accounts and Security Groups behaviour.
Oracle UCM version: 11.1.1.5.0
Steps:
1. Log in with "weblogic" user and created a content with id "content1"
2. Applied "@acc1(R)" and "TestGroup1" to the cotent created in step 1
3. Log out
4. Log in as "acc1user1", the user is not able to see the "content1"
5. Log out
6. Log in as "role1user1", the user is not able to see the "content1"
Account and Group information:
1. User "acc1user1" is part of "@acc1(R)"
2. User "role1user1" is part of "role1(R)" and is mapped to "TestGroup1" in UCM
Expected:
Both "acc1user1" and "role1user1" should be able to see "content1" as they have at least Read permission.
Please help me understand why the users are not able to see the content.

ACLs, like Accounts, are optional security setting which may add on some extra functionality to mandatory security groups. Likewise, the resulting permission is taken as an intersection of SG and ACLs.
But in the second part the number of set of users is huge (approx say 600)I don't get this completely. Does this mean that those "sets of users" (users who see the same data) are distinct and that there is 600 of such groups?
If you read thoroughly the manual I sent earlier, there is a recommendation that there should be maximum 50 security groups, and you should use accounts, should this number be exceeded. This means you could have all the documents in one security group (and have one common role with Read permission), but combine it with accounts. ACLs are not a good choice here - their performance and manageability is much worse than of accounts. ACLs are primarily used if you expect security settings to change during the lifetime (e.g. a project manager adds temporarily rights to access an item to another user, and revokes it when the user finishes his or her work).
Note that accounts as well as permissions of users within accounts can also be mapped externally (from LDAP/AD) and it usually follows some kind of org chart.
I'd feel more comfortable not to speak about users, security groups, roles, etc., but about some real-life objects and scenarios.

Need info regarding HANA DB & MaxDB/SAPDB

Hi All,
I have a requirement where in I need to get the following information in regard to HANA DB & MaxDB/SapDB. Kindly suggest.
This info I need to get from ECC or similar Box. Please let me know in which SAP table we can get this info.
Information requried
================
Database version
Schemas
Database parameters
Configuration files
Data files
Log files
Regards,
Mani

> Database version
> Schemas
System - status
> Database parameters
> Configuration files
> Data files
> Log files
DB50 - or DBACOCKPIT
Markus

Variant to data: Need info regarding type of data

Hello,
What I want to do is very basic. I will acquire the image using CCD camera. The
image is a raw data type: 2D array of type long (4 bytes per element) or integer (2 bytes per element). I can save the image even as .tiff file. Using Variant To Data, I am converting the image so that labview can handle it (I am not sure whether I really need this) before I write that data to some file and save it. I have to define data type for Variant To Data. I tried to define the data type. However, I am confused. Would anybody give me some suggestion?
Thanks a lot,
Dushyant

Hrm, you'll need to be more specific about your actual question in order for us to give you a good answer, but, without more information, I'd say you should just define the type as a 2-d array of either longs or words. (i.e. get an array constant, place a numeric constant inside of it, right click the numeric constant, and select Representation->Long or Representation->Word then wire the constant to the Type input of the Variant to Data).
If you're dealing with variants, I'd guess you are probably calling an ActiveX control or server to communicate with your camera?
Regards,
Ryan K.

Need info regarding disk packs

Greetings.
There is a need to maintain different dev/production configurations (for different
customers or different software releases) on the same Sun system (for
example T5120/T5220 or similar) and have the ability to switch to a
particular configuration. I came to know that there is something
called "disk packs" available from Sun which is cluster of disks and
we can selectively deploy multiple OS/Configs in one of more disks
and activate the desired configuration whenever there is a need.
Would you be please able to provide if you have any information in
this regard or suggest us what solution would work best for this usecase.
Thanks
Anand

ACLs, like Accounts, are optional security setting which may add on some extra functionality to mandatory security groups. Likewise, the resulting permission is taken as an intersection of SG and ACLs.
But in the second part the number of set of users is huge (approx say 600)I don't get this completely. Does this mean that those "sets of users" (users who see the same data) are distinct and that there is 600 of such groups?
If you read thoroughly the manual I sent earlier, there is a recommendation that there should be maximum 50 security groups, and you should use accounts, should this number be exceeded. This means you could have all the documents in one security group (and have one common role with Read permission), but combine it with accounts. ACLs are not a good choice here - their performance and manageability is much worse than of accounts. ACLs are primarily used if you expect security settings to change during the lifetime (e.g. a project manager adds temporarily rights to access an item to another user, and revokes it when the user finishes his or her work).
Note that accounts as well as permissions of users within accounts can also be mapped externally (from LDAP/AD) and it usually follows some kind of org chart.
I'd feel more comfortable not to speak about users, security groups, roles, etc., but about some real-life objects and scenarios.

Need info regarding the infoobjects

Hi All,
My question is:
when we display where used list for an infocube(an example), it will display the list of queries where it is been used in the system in the info-object format.(BW object list format like 4EPSFH54S2SE etc.,)
Using this information how to find the technical name or the description of this query.
Thanks with regards,
Vinay

you can use the table RSRREPDIR to get the necessary information...
rgds, Ghuru

Need info regarding OCA

Hi, All
I am looking for first certification for OCA. I have seen the syllabus also.
Please suggest me and provide me material, if you have.
mail me at [email protected]
Thanks in advance
Arun

Hi Arun,
you need prepare the first 13 chapters of Oracle's Introduction to Oracle 9i: SQL pdfs..
Regards
Sai Krishna

Need info regarding tasks in ThreadPool, Executor and ExecutorService

Hi all,
I would like to know the answers for the following questions regarding tasks:
1.How do you create a self-starting task.(the task that starts executing as soon as we create runnable object)
2. how do we create a task which is executed outside the runnableObject
3. If we are executing one task in a program, how many tasks are actually running in the JVM
4. how do we know whether a task is active or not
5. what happens when a task in in wait but no one signals it
6. what happens when a task does not release the lock
7. which method is used to pause a task
8. how do we stop and restart a task
9. if three instances of a runnable class start executing in parallel, which one terminates first.
I was looking for the answers for the above question in java doc and few other sites, but was of no help.
It would be great if anyone can answer these questions. That would be lot of help.
Thanks!!

I see nothing in your questions relating to ThreadPool or Executors.
Sounds like a "homework" assignment.
First thing you need to be clearer on is what is a "task". There is no pre-defined notion of "task" in Java.
Any introductory text of multi-threading in Java will answer those questions as they apply to threads. See the FAQ for some references.
David Holmes

Very important and urgent - i need info regarding a function module

hi all,
can any one suggest me a function module which calculate the
difference in two dates and give answer in days.
some one suggest me the following function m odule
CALL FUNCTION 'HR_SGPBS_YRS_MTHS_DAYS'
       EXPORTING
            beg_da     = wpv_dati
            end_da     = wpv_datf
       IMPORTING
            no_cal_day = wpv_days
Please suggest any other function module.
or i can use this Function module only

Hi,
U can use the following function module.
CALL FUNCTION 'DAYS_BETWEEN_TWO_DATES'
EXPORTING
    I_DATUM_BIS                   = date1
    I_DATUM_VON                 = date2
I_KZ_EXCL_VON              = '0'
I_KZ_INCL_BIS                 = '0'
I_KZ_ULT_BIS                  = ' '
I_KZ_ULT_VON                = ' '
I_STGMETH                     = '0'
I_SZBMETH                     = '1'
IMPORTING
    E_TAGE                        = days
EXCEPTIONS
DAYS_METHOD_NOT_DEFINED       = 1
OTHERS                        = 2
Reward if useful.
Regards,
Rajesh Akarte

Need info regarding reports

Hi all
Can any one tell me what is the order of services that supposed to be start before navigating in to financial reporting , web analysis.
I guess we can navigate in to reports through workspace ..if so how ?
when ever I try to start financial reporting studio I am getting a dialog box saying
run time error 429
activex componnent cant create object ---- how to resolve this.
forget to say ...our version is 9.3.1 with sql server.
Please tell me the sequence of services that we need to start
Thanks
M.V

Hi,
This is the order that I usually start services if it is just for Reporting & Analysis.
Shared Services
Essbase
Apache Service
BI+ Core Services
Workspace
Financial Reporting RMI
FR Print Server
FR Report Server
FR Scheduler Server
FR Web Server
Web Analysis
Also if you could try posting on the Query and Reporting Forum for further help :- Hyperion Query and Reporting
Usually the error you are pointing out means that the Hyperion Configuration Ultility has not been run on the client machine where the studio is on, try running the config ultility for Financial Reporting.
Cheers
John

Need info regarding BADI CRM_COND_COM_BADI.

Hello experts,
My requirement is to calculate the value of a specific condition type based on a custom attribute that is maintained in Item Master.
I added a new field in Condition Field catalog for this and implemented BADI CRM_COND_COM_BADI to pass the new attribute value to Pricing. This works fine till creation of Billing Due List.
The issue is that we are redeterming the automatic condition entries during Billing document creation. It seems that the BADI is not getting triggered beacuse of which the Condition entry is not present in Bill Doc anymore.
Any inputs in this regard will be appreciated.
Regards,
Amit

Hi davide,
The BADI CRM_COND_COM_BADI is used for filling the pricing communication structure.
If you have added any field at header level of the field catelog that will available in the changing parameter of the method HEADER_COMMUNICATION_STRUCTURE.
If you have added any field at item level of the field catelog that will available in the changing parameter of the method ITEM_COMMUNICATION_STRUCTURE.
Additional fields added at catelog can be filled with the values using this BADI.
Thanks & Regards,
Raghuram. K.R.

NEED INFO REGARDING WORKFLOW MAILER &MAPI

HI,
Need information
our workflow mailer is configured with LOTUS NOTES now we wanna to
move to OUTLOOK and we use IMAP4 protocol now we wanna to
replace this with MAPI.
So please let me know how to configure in OUTLOOK and also
MAPI is a oracle certificated protocol and how to configure it.
Thanks in Advance,
Vandana

Please see these docs.
What Mail Server Types Can Be Used To Configure The Workflow Java Mailer In R11i and R12.+ [ID 943578.1]
A System Administrators' Guide: Oracle Applications 11i Workflow [ID 139745.1]
WF 2.x: Configuring the Notification Mailer v 2.0.3 - 2.6.2 (not OAM) - MAPI [ID 104197.1]
Thanks,
Hussein

Need info regarding caches

Plz correct me if I am wrong
1) Index cache is buffer where the index pages are located .and Index pages consists of pointers and these pointers tell you where the data blocks are located on the disk.
2) Data Cache is buffer where essbase created to store uncompressed data blocks
3) How about .pag files ? I guess these files consists of the data block information ie data values.
4) then How about .dat files? What these files exactly contain.
5) Data file cache is buffer where essbase creates to store compressed data blocks. I read that data file cache will be created only if you are using direct i/o .. why you need data file cache as essbase is taking data directly from disk.
6) calc cache is goiing to be created to store the blocks that are needed for calculation
Please clarify me on this caches. Correct me if there are any mistakes
Thanks

1) Index cache is buffer where the index pages are located .and Index pages consists of pointers and these pointers tell you where the data blocks are located on the disk.
Yes
2) Data Cache is buffer where essbase created to store uncompressed data blocks
Yes
3) How about .pag files ? I guess these files consists of the data block information ie data values.
A file that contains data blocks. Essbase generates the data file upon data load and stores it on disk. Essbase names data files incrementally—essxxxxx.pag, where xxxxx is a number starting
with 00001.
4) then How about .dat files? What these files exactly contain.
.dat files are data files for storing data.
5) Data file cache is buffer where essbase creates to store compressed data blocks.
The size of the data file cache determines how much of the data within the data files can fit into memory at one time. The data cache size and the data block size determine how many data blocks can fit into memory at one time. Data files for a single database can span multiple volumes;multiple databases can reside on the same volume.
6) calc cache is goiing to be created to store the blocks that are needed for calculation
Yes.

Need info regarding static file cache in weblogic

Hi,
I want to cache the static files at weblogic side
I am using Apache plugin provided by weblogic
I have gone through the e-docs about FileCache ON which is needs to be set in httpd.conf
I want to know is there any settings which is set at weblogic to cache static files
As i am using apache plug in provided by weblogic i want to know if there is any setting at weblogic side
Thanks in advance

Hello,
Normally the statis contents are served from web servers, in your case this may be from Apache. So what statis files are you referring to in weblogic, is that a part of HTML and images from WAR / EAR ?
In general weblogic has its own cache temp location as runtime to keep the classfiles and other resources unpacked from WAR / EAR.
-AJ

Need info regarding light weight AP 1042 registration

Similar Messages

Maybe you are looking for