Need info regarding the infoobjects

Hi All,
My question is:
when we display where used list for an infocube(an example), it will display the list of queries where it is been used in the system in the info-object format.(BW object list format like 4EPSFH54S2SE etc.,)
Using this information how to find the technical name or the description of this query.
Thanks with regards,
Vinay

you can use the table RSRREPDIR to get the necessary information...
rgds, Ghuru

Similar Messages

Need inputs regarding the dvd drive on primary ide channel.

Specs:
Motherboard: MSI P35 Neo3 (MS-7935 1.0)
CPU: Intel Core2 Duo E6550
Memory: Team Elite DDR2800 (2x1GB Dual Channel)
Hard drive: Seagate Barracuda 7200.11 500GB 32MB Cache (SATA)
Optical drive: LG GSA-H55L (IDE only) Firmware version 1.02
Graphics card: Gecube HD3870
Chipset: Intel P35/G33/G31 (Rev. A2)
Southbridge: Intel 82801IB (ICH9)
LPCIO: Fintek F71882F
BIOS: AMI V1.1 (11/07/2007)
Hello,
Almost all new motherboards today only have a primary ide channel and the rest are SATA.
I need inputs regarding the dvd drive which is shown in device manager as located on the primary ide channel while the hard drive is located on the secondary channel. Because I would like to update the dvd drive to the latest firmware (version 1.06; to be able to recognize more blank media) but the LG site recommends that the drive (dvd) be located on the secondary ide channel.
I already tried to uninstall every channel from the device manager but all would still be the same after reboot, dvd drive on primary, hard drive on secondary.
Current ide mode in BIOS is set to AHCI+IDE mode, DMA modes are fine (UDMA4 for dvd, UDMA5 for hard drive), boot sequence (1st=HD, 2nd=DVD, 3rd=Floppy drive)
Tried switching to IDE mode only in BIOS but would not detect the optical drive. Never tried RAID+IDE mode since I only have a single hard drive.
I'm not sure but if I try to update the firmware, it might instead try to update the hard drive's firmware instead of the optical drive and make the hard drive unusable.
I would like to know if anybody with this same situation was able to successfully update the optical drive's firmware or is there some way to place the optical drive on the secondary ide channel and the hard drive on primary for me to follow and replicate the process.
Thank you for any replies.

Thanks sir NovJoe for the reply.
Just received the solution from another forum where I posted the same problem.
They said that the flash program for the firmware will detect the drive on its own and would not flash other devices except the optical drive itself. So its pretty safe, and I can confirm this since I just flashed my ODD a little over a while ago and everything went fine. No errors.
Though I'm speaking for the brand of ODD I own and may be different for other brands so take precautions as well. It may be different for the others.

I need information regarding the creation of Workbook and WAD.

Hi,
I need information regarding the How to create the Workbook and WAD.
Can any one help me to get the information..
Regards,
Suman
Edited by: Suman Reddy Vuyyuru on May 19, 2009 8:22 AM

Hi,
for workbook:
[Queries in Workbook|http://help.sap.com/saphelp_sem40bw/helpdata/en/e3/e60138fede083de10000009b38f8cf/frameset.htm]
for WAD:
[WAD for Beginners|https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/749a4622-0a01-0010-36bf-b6b30a2a3a22]
thnks.

Need info regarding HANA DB & MaxDB/SAPDB

Hi All,
I have a requirement where in I need to get the following information in regard to HANA DB & MaxDB/SapDB. Kindly suggest.
This info I need to get from ECC or similar Box. Please let me know in which SAP table we can get this info.
Information requried
================
Database version
Schemas
Database parameters
Configuration files
Data files
Log files
Regards,
Mani

> Database version
> Schemas
System - status
> Database parameters
> Configuration files
> Data files
> Log files
DB50 - or DBACOCKPIT
Markus

Need info regarding infotype 0017.

Dear Experts,
I am new to Travel Management.
In infotype 0017, I need information regarding RGrp M/A Statutory, RGrp M/A Enterprise,EE Grp Expense Type and EE Group Travel Mgt fields.
I verified few config documents of Travel Management but could not understood the applicability of the above fields. Please help me in this regard.
Points could be awarded accordingly.
Regards,
Dolly

Hi,
RGrp M/A Statutory-> Identifies a reimbursement group for meals/accommodations for which the same statutory or pay scale trip provisions for meals and accommodations are valid
A reimbursement group is a grouping of employees for whom the same trip provisions are valid. The reimbursement group is specialized by the trip expense category.
A reimbursement group for meals/accommodations is a reimbursement group for which the same trip provisions for meals/accommodations are valid.
The reimbursement group for meals/accommodations is specialized as to whether it is needed to represent statutory/pay scale or enterprise- specific trip provisions.
Example
Trip costs levels A, B, C according to German Travel Expense Statutes
Grouping of employees according to pay scale groups
RGrp M/A Enterprise-> Identifies a reimbursement group for meals/accommodations for which the same enterprise-specific trip provisions for meals and accommodations are valid
A reimbursement group is a grouping of employees for whom the same trip provisions are valid. The reimbursement group is specialized by the trip expense category.
A reimbursement group for meals/accommodations is a reimbursement group for which the same trip provisions for meals/accommodations are valid.
The reimbursement group for meals/accommodations is specialized as to whether it is needed to represent statutory/pay scale or enterprise- specific trip provisions.
Example
Members of the Executive Board
Managers
Salaried employees
Industrial workers
EE Grp Expense Type -> An employee grouping for trip expense type is a classification of employees for whom these trip expense types are permissible.
Example
- Executive Board
- executive employee
EE Group Travel Mgt fields-> An employee grouping for Business Trip Management is a classification of employees designed to fulfill the purposes of Business Trip Management.
Example
- employee
- mailman
- other
Regards,
Pramitha.

Need info regarding Oracle UCM Accounts and Security Groups behaviour

Need information regarding Oracle UCM Accounts and Security Groups behaviour.
Oracle UCM version: 11.1.1.5.0
Steps:
1. Log in with "weblogic" user and created a content with id "content1"
2. Applied "@acc1(R)" and "TestGroup1" to the cotent created in step 1
3. Log out
4. Log in as "acc1user1", the user is not able to see the "content1"
5. Log out
6. Log in as "role1user1", the user is not able to see the "content1"
Account and Group information:
1. User "acc1user1" is part of "@acc1(R)"
2. User "role1user1" is part of "role1(R)" and is mapped to "TestGroup1" in UCM
Expected:
Both "acc1user1" and "role1user1" should be able to see "content1" as they have at least Read permission.
Please help me understand why the users are not able to see the content.

ACLs, like Accounts, are optional security setting which may add on some extra functionality to mandatory security groups. Likewise, the resulting permission is taken as an intersection of SG and ACLs.
But in the second part the number of set of users is huge (approx say 600)I don't get this completely. Does this mean that those "sets of users" (users who see the same data) are distinct and that there is 600 of such groups?
If you read thoroughly the manual I sent earlier, there is a recommendation that there should be maximum 50 security groups, and you should use accounts, should this number be exceeded. This means you could have all the documents in one security group (and have one common role with Read permission), but combine it with accounts. ACLs are not a good choice here - their performance and manageability is much worse than of accounts. ACLs are primarily used if you expect security settings to change during the lifetime (e.g. a project manager adds temporarily rights to access an item to another user, and revokes it when the user finishes his or her work).
Note that accounts as well as permissions of users within accounts can also be mapped externally (from LDAP/AD) and it usually follows some kind of org chart.
I'd feel more comfortable not to speak about users, security groups, roles, etc., but about some real-life objects and scenarios.

Need clarification regarding the test cable-diagnostics tdr command

Hello,
I've read about the test cable-diagnostics tdr command but I need clarification on the examples listed below to make sure that I am providing the right answer to my co-workers.
Example 1:
CXXX7SW17#show cable-diagnostic tdr int g0/20
TDR test last run on: July 16 10:23:00
Interface Speed Local pair Pair length        Remote pair Pair status
Gi0/20    auto Pair A     N/A                        N/A                Normal
                       Pair B     72   +/- 10 meters N/A                Open
                       Pair C     75   +/- 10 meters N/A                Short/Crosstalk
                       Pair D     74   +/- 10 meters N/A                Short/Crosstalk
Does this example mean that there's a cable length issue in the line which is causing the device that it's connected to not to work properly?
Example 2:
CXXX2SW140#show cable-diagnostics tdr int g0/21
TDR test last run on: July 16 09:16:22
Interface Speed Local pair Pair length        Remote pair Pair status
Gi0/21    100M Pair A     N/A                      Pair A           Normal
                          Pair B     N/A                      Pair B           Normal
                          Pair C     N/A                     Pair C           Normal
                          Pair D     N/A                     Pair D           Normal
Does this example state that the cable line is okay for use?
Example 3:
CXXX1SW19#show cable-diagnostics tdr int g0/22
TDR test last run on: July 16 06:36:53
Interface Speed Local pair Pair length            Remote pair Pair status
Gi0/22   auto    Pair A       1    +/- 10 meters N/A               Open
                          Pair B     39   +/- 10 meters   N/A               Open
                          Pair C     72   +/- 10 meters   N/A               Open
                          Pair D     1    +/- 10 meters    N/A              Open
Does this example mean that there isn't a device connected on the other end? No pin-contact?
Thank you very much for any help you could provide.
S

I found this article here at supportforums that seemed like the best explanation I've read so far for TDR info.
Hope that helps.

Need help regarding the few clarification in writing cmod

Hi All,
I need to write a cmod by creating a new project for that. The main purpose is to define variables in it which will be used in reporting(restrictions).
Now I need to enhance that structure with RSR00001 code since it dealys with declaring the variables.
But this enhancement code is being used in some other project as well, because of it I am unable to use it in my project..
Can you please explain me how can I overcome this situation.
Thanks,
vinay.

Hi Vinay,
Write this code in CMOD :
data:
z_include type program,
Z_return.
when others.
* Select the include program using the variable
    perform select_include using    i_vnam
                           changing z_include
                                    z_return.
    check z_return = 0.
* Check that include program exists
    perform check_include_program using    z_include
                                  changing z_return.
    check z_return = 0.
* Process the appropriate variable by calling the generic form
* 'PROCESS_VARIABLE' in the include program just selected
    perform process_variable in program (z_include)
                             tables   e_t_range
                                      i_t_var_range
                             using    i_vnam
                                      i_vartyp
                                      i_iobjnm
                                      i_s_cob_pro
                                      i_s_rkb1d
                                      i_periv
                                      i_step
                                      lv_zs_bsw_offset
                             changing e_meeht
                                      e_mefac
                                      e_waers
                                      e_whfac
                                      c_s_customer.
FORM select_include using    p_var
                     changing p_include
                              p_error.
select single zinclude
    into p_include
    from zvariables
    where zvarname = p_var.
p_error = sy-subrc.
ENDFORM.
form check_include_program using    p_include
                            changing p_error.
data:
    l_name type programm.
select single name
    into l_name
    from trdir
    where name = p_include.
p_error = sy-subrc.
endform.
Then you can create a table having two column, variable value and its corresponding program.
You will then not need to disturb the CMOD Code.
-Vikram

Need help regarding the location of Exchange 2013 Logs for parsing

Hi, I am trying to create reports based on the logs that are created on my exchange server. I am using
exchange 2013. My problem is that I cannot handle every log, and instead want specific types of logs.
I need help finding the specific locations of the following types of logs (If they even exist), so that I can parse them and use them effectively:
Audit Logs (Mailbox logons, Mailbox permission changes, Mailbox property changes,
Exchange store changes)
Mail Report Logs (Mailbox size and growth, Mailbox storage growth, Enabled users, Expired and Soon-to-Expire Mailboxes)
Exchange Traffic Reports (Details on size and amount of messages sent and recieved, Internet traffic [to and from], Traffic between exchange users)
I understand this might sound like a huge undertaking, but any help that can be provided would be appreciated.
Again, I need information on the locations of these types of logs on the exchange server, so that I can parse them. Collecting them all and searching through them is not practical for my available resources.
Thanks,
Matt

Audit Logs (Mailbox logons, Mailbox permission
changes, Mailbox property changes, Exchange
store changes) ---- these are two type of logs, 1. mailbox audit logs and that is stored in each mailbox under dumpster
http://technet.microsoft.com/en-us/library/ff461930(v=exchg.150).aspx however you need to
enable
it for individual mailboxes... 2. admin audit log, this is stored into a system mailbox dumpster.... http://technet.microsoft.com/en-us/library/dd335052(v=exchg.141).aspx
Mail Report Logs (Mailbox size and growth, Mailbox
storage growth, Enabled users, Expired and Soon-to-Expire Mailboxes) ---- there isn't any specific log for this, you would need to create some time of script to collect this every day for you and store it somewhere... This is a good start... http://www.stevieg.org/2011/06/exchange-environment-report/
Exchange Traffic Reports (Details on size and
amount of messages sent and recieved, Internet traffic [to and from], Traffic between exchange users) ----- This you can get from message tracking log... http://technet.microsoft.com/en-us/library/bb124375(v=exchg.150).aspx

Need info regarding ECC 6.0

Hi All,
Can you please provide me some good links regarding the addtional functional feature added in ECC 6.0 terms of FI & CO when compared to 4.7 version.

hi
please check the SAP solution browser

Need info regarding Contracts

Hi All,
Please provide me information regarding the standard database tables that store the details of contracts at Header level and Item level created using the transaction crmd_order.
All helpful answers will be rewarded.
Regards,
Udaya

Udaya,
Try the database trace under Performance Analysis (TCode ST05) and execute the desired processing in a second session under your user name.
You can deactivate the trace and review it for the details.
Here's what we find:
Contracts created as sales transactions are stored as follows -
Header: CRMD_ORDERADM_H
The fields OBJECT_TYPE and PROCESS_TYPE can differentiate Contracts from other activities. Standard Sales Contracts have OBJECT_TYPE = BUS2000121.
Item: CRMD_ORDERADM_I
The item level table holds the item details and is referenced using the header GUID in the Header table.
OBJECT_TYPE of standard Sales Contract items is = BUS2000136.
From the Item you can get your PRODUCT field (guid) for using in product and pricing details etc. under the subsequent pricing, product and activity details.
Brad

Need feedback regarding the recovery discs

Hi,
I have recently acquired a T61 with Vista Business. It did not come with pressed rescue CDs, therefore I immediately generated the set of 10 recovery CDs using the Lenovo software.
I will have to move some partitions soon (to install BSD and other experimentations). The computer came with 2 partitions, the first one being a 6GB containing the recovery part and the second one being the installed system. If I remove them (or move them), will the recovery CDs recreate these partitions, reformat and reinstall them as initially? Even if I completely wipe the drive and remove all partitions? Or are there differences (do I need to redo the initial partitioning again) ?
Thanks in advance.
Message Edited by zeb on 04-28-2008 11:57 AM

The recovery media should return the machine to the same state you received it in. My TP has shipped and the first thing I plan to do is to create the recovery CD/DVDs AND make sure they work before experimenting.
..."I immediately the set of 10 recovery CDs"...I assume you meant that you made the set yourself, right?
There are some reports of people who ordered VistaBus also receiving XP downgrade recovery discs, but they didn't realize that and neglected to make their Vista recovery discs from the HD before messing with the partitions.

Help/Info regarding the CL rating of RAM upgrades.

I'm upgrading my Early 2011 Macbook Pro 17 to 8GB Ram and I'm curious if anyone can offer advise regarding the CL rating. All the DDR3 1333GHz SODIMM kits have a CL9 rating. Is this a higher latency than the 4GB of ram that I have already? If so, will more latency actually do more harm than good??
Pardon me if I sound like a noob!
I'm running a stock MBP 17 8,1 2.2GHz i7 with Windows 7 Pro Bootcamp. (Windows & + Zone Alarm = 50% RAM usage when using Excel, UGH!)

No, CL9 is a standard. I have the same model and put 8G from Omni Technologies in mine. It screams!
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 

Need the info regarding the MSI Theater 550 PRO TV Tuner Card

I would like to know whether the product MSI Theater 550PRO is compatible with Windows7 or not?

No, only XP and Vista.
http://eu.msi.com/product/mm/Theater-550PRO.html#/?div=Driver

Need Help regarding the JVM for the ARM926EJS Processor

I Want to develop an application in java for the IMX.27 board which has ARM926EJS Procesor. This processor is jazelle enabled hardware.
My questiion is that how to get the JVM for this. So that i will use my Java appliaction. I am using linux OS.
Thanks in advance.

Hi Narendra,
Sun actually has a VM for the ARM ... well, actually 2 VMs for the ARM. Depending on your needs, there's a solution for JavaME CLDC, JavaME CDC, or JavaSE. There's also the open source implementations for CLDC and CDC. Here's how to get more info:
JavaME: http://java.sun.com/javame/index.jsp
CLDC open source project: phoneME Feature: https://phoneme.dev.java.net/content/phoneme_platforms.html#phonemefeature
CDC open source project: phoneME Advanced: https://phoneme.dev.java.net/content/phoneme_platforms.html#phonemeadvanced
Embedded SE: http://java.sun.com/j2se/embedded/offerings.html
email inquiry to: [email protected]
Regards,
Mark

Need info regarding the infoobjects

Similar Messages

Maybe you are looking for