Need instructions for replacing battery

Hey, all.
The "Replace Battery" light is lit on my ONT, and it is (of course) doing that annoying beeping noise.
Since the only way to permanently stop the beeping is to disconnect the battery, I'd like to do that.  Unfortunately, none of the instructions I've seen online, or gotten from Verizon customer service, have applied to my specific ONT model.
I have a Motorola ONT1000GJ2  (Yes, GJ, not GT, I've checked repeatedly).  I *think* the battery is in the upper section of the housing, but I cannot, for the life of me, figure out how to get to it.
If anyone has achieved this blessed state of affairs of actually getting to this battery, could you be so kind as to fill me in on how?
Thanks in advance!
Solved!
Go to Solution.

I am providing my own answer to this question, as the community didn't come up with an answer, and Verizon customer "service" (and I use the term extremely loosely in this regard) was the exact opposite of helpful.
Looking at the picture above, on the far right-hand side, there are two recessed hex-screws, one above the other.  To access the battery compartment on this particular model, leave the lower screw tightened, and loosen the upper screw.  Don't worry about it falling out: I'm pretty sure it's a "captive" screw, and so cannot be fully removed.
Once you have the screw loosened, pull outward on the upper right corner of the box.  You may have to lift up at the same time, if it hangs up on you.  (In order to lift up on it, put a finger or thumb in the screw's recess, and push upward).  Continue to jiggle and pull, and eventually the stupid thing will come open.  Once you've got it open, removing the battery and then the battery clips is the same as in the videos they've provided:  Pull back the tabs to slip the battery out, and then wiggle the connectors off the battery posts.
WARNING:  The battery is several pounds in weight, and the wires are not all that long.  If you have to stretch to get to your unit like I do (mine is mounted above my washer/dryer), you will benefit from a helper, so they can hold the battery while you remove the battery connectors.  I know I struggled a bit trying to do it alone.
Thanks to those who attempted to help me.  I hope this is able to help someone else in the future.
Oh, and one more piece of info:  Verizon "customer service" will repeatedly tell you the only official way to make the unit stop beeping is to replace the defective battery with a new one.  They have to utter the word "official", because otherwise, you can accuse them (accurately) of lying.  The unit will stop beeping as soon as you disconnect the old battery.  They, of course, want you to spend $30+ buying a new battery from them, so they will not tell you this.  If, like me, you have no desire to replace the battery, rest assured, the unit will stop annoying you once you've got the old battery out of it.  The "Replace Battery" light will remain on, but the audible warnings will end.

Similar Messages

  • Need recommendation for replacement battery on Wallstreet PB

    I have a PB G3 Series Wallstreet (292MHz, family M4753) for which I need to replace the battery. Other World Computing has a replacement for $130. There is also lots of others in the $60 to $90 range. This is only for occasional use. 2 hours run time is fine. Is there any way to know if any of these less expensive batteries are OK? Thanks
    Owen

    Batteries Plus is a franchise. I asked my local (West of Boston) franchise what the majority of its business was, and they pointed to the shop table where several laptop batteries were being re-built and explained they replace the cells in laptop batteries. They also had displays of coin batteries, alarm system backup batteries, and other specialty batteries.
    If you got the guy who started today, he might have heard "Re-Sell old batteries" and thought you were strange. Who would buy used-up old batteries? Maybe it's just not a big business where you are, or maybe they have not signed up for the training yet.

  • Need instructions for replacing ethernet port

    My Blue and White G3 had its ethernet port killed during a recent power surge. Does anyone know where I can find a website that will instruct me how to replace it.

    Caution about third-party cards -- some of the companies that made them have gone out of business. Be sure that if the card is not genuine Apple, you get the driver with it.

  • Need instructions for 17" LCD replacement...

    Need instructions for the original (non-ALS) 17" LCD replacement...
    Ive replaced everything else, time to replace the LCD, but need the procedure to do it.
    Thanks

    Before you do surgery on your imac, go to applications, system preferences, displays, and see if you can adjust the brightness. My screen was significantly darker after I upgraded to 10.4.3 and I was able bring it back to life. For some reason the upgrade caused the brightness button to regress to 0 on a scale of one to ten- hope this works for you

  • Need Instructions for installing AE card in dual G5 tower

    I need instructions for installing a AE card in a dual 2 GHZ powermac G5. I understand I need to also install an external antenna. Since I do not have an antenna where is the best source for the antenna, apple or an outside vendor. My G5 is presently connected to a netgear router and I want to use the AE card to communicate with an airport express base station with airtunes connected to my stereo receiver. Would this create a conflict since my computer is connected to the netgear router. Any help would be appreciated.
    ron

    ] I need instructions for installing a AE card in a dual 2 GHZ powermac G5.
    http://www.info.apple.com/usen/cip/pdf/g5/apec_c.pdf
    ]I understand I need to also install an external antenna. Since I do not have an antenna where is the best source for the antenna, apple or an outside vendor.
    You are going to need the t-shaped external aerial otherwise this is not going to work. Even though your PowerMac did not come with an Airport Extreme Card built in, it would have been supplied with the aerial.
    You will need to find a replacement.
    ]I want to use the AE card to communicate with an airport express base station with airtunes connected to my stereo receiver. Would this create a conflict since my computer is connected to the netgear router.
    I am presuming that your Netgear is not wireless.
    Can you connect the Airport Express to the router are do you want it in a different room?
    You will be able to be connected to the router and AX at the same time, but in order to avoid internet and network issues, you should ensure that built-in-ethernet is above Airport in the network configurations.

  • The Examples They Show Are not for my computer I Need instructions For A Windows Computer HP TouchSmart

    The Examples They Show Are not for my computer I Need instructions For A Windows Computer HP TouchSmart

    hp
    The answers are in the details, and you have not given us enough details to help you.
    Right now I am guessing at what you seek. Are you trying to use your HP Touch Screen to do your
    Premiere Elements importing, editing, and exporting and the Touch Screen movements are not working
    to do what you want to do in Premiere Elements?
    Have you configured the HP computer Touch Screen? Using the Touch Screen, what cannot you do
    that you can do with the mouse?
    HP Support document - HP Support Center
    If I am guessing correctly here, does the mouse work instead of the Touch Screen to allow you to
    work in the program.
    I suspect that Premiere Elements does not support Touch Screen and you will end up using a mouse, but I would need to do more homework on
    that.
    This is not Adobe. Rather user to user. If you are dealing with the current version, 13, you might want to contact
    Adobe about the matter. More on that later, once you confirm the above or let me know that I have completely
    misinterpreted your question/concern.
    ATR

  • Need instructions for downloading/installing Flash Player

    Need instructions for downloading/installing Flash Player in my PC

    Hi, This is the Adobe Flash Player Uninstall link:
    http://kb2.adobe.com/cps/141/tn_14157.html
    This is the Adobe Troubleshooting Guide which you may want also to review. I would suggest using the Manual Installers which you can download and SAVE to your Desktop. Pay attention to any apps using Flash, you may need to Disable any Anti-Virus. Be sure to use the Administrator Account and check Settings. Be sure to Reboot after running the Uninstaller and also after Installing.
    http://kb2.adobe.com/cps/191/tn_19166.html
    eidnolb

  • I need instructions for using my HP Photosmart D5345

    I need instructions for operating my HP Photosmart D5345.  I lost them.

    Hi Tigger59,
    Here is a link to the online manuals for the HP Photosmart D5345:
    http://h10025.www1.hp.com/ewfrf/wc/manualCategory?cc=us&dlc=en&jumpid=reg_r1002_usen&lc=en&product=3...
    If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

  • I need instructions for installing blue tooth for apple iphone 4s?

    I need instructions for installing blue tooth for apple iphone 4s?

    We have Jabra bluetooth.  We got out the instructions that came with the Jabra and and followed them.  Worked like a charm.  Just remember that once the bluetooth is paired, you cannot go more than 30 feet from your phone while using it.

  • Need instructions for setting up wireless network at home, w/o base station

    I have a new iMac with Airport Extreme card and a MacBook, also with a card. I need instructions for connecting the two Macs via Airport. I do not have a base station. The Help on the Mac does not match my actual system.
    All of the manuals that I can find are for the base station.
    Please help.

    Hi W
    You don't mention if you have any kind of internet connection on either computer, so I'll assume that you don't, and this setup will simply network the two computers with no consideration of the internet.
    On either of the computers, make sure that the Airport icon is visible in the menubar, and that Airport is active - check System Preferences, Network, Airport to make sure both are the case. Now, in the menu icon, click "Create Network". You'll be prompted to name the new network, set a channel if you need to, and you can also set a password under "Show Options". Once the network has been created, your Airport icon will change to a solid grey with a computer inside it.
    You should now be able to connect to the new network on your other Mac and share services.
    Let me know if you have any problems with it.
    Matt

  • Need instructions for iphone 4

    need instructions for use of iphone 4 - where can I obtain please.
    cant be simpler

    The manual can be found at Apple - Support - Manuals
    Allan

  • Need instructions for creating T61 XP backup media

    Can you direct me to instructions for creating the backup media (DVD preferably) for the existing 4GB backup partition on my T61 running XP?  It is intact, and I can boot into it, but I'd sleep a little better if I had the option of booting from external media.  I'm aware of the advice to call and purchase this media, but I would prefer to just make it myself, if possible.  
    Thanks!
    Moderator Note; post moved to start new thread, subject edited.

    I don't recall the step by step, but there is a menu item in the lenovo section you can use to burn recovery media from within windows. If I'm not mistaken, it can only be used once, however if someone already burned a set you can still restore from the harddrive and after restored you will again be able to burn one copy of recovery media.
    However, I'll give you my own personal opinion on this. When you install from this recovery media you'll have an outdated operating system. The T61 recovery disc was made in 2006 or 2007 and after you install it you'll need to install the latest service pack, then you'll probably want to replace all the drivers and all the lenovo apps that are also outdated. You're going to end up replacing nearly everything, plus you're going ot have several redundant copies of all this outdated stuff taking up space. My preferred method is to use a windows setup disc that has the latest drivers and critical updates integrated, then go online and download the latest drivers for your hardware and as much or as little of the lenovo products that you want on your system. You then save an enormous amount of harddrive space and have a computer without all the bloat and it all gets done in a fraction of the time. The last time I installed from a factory restore disc set it took hours, then several hours more to replace everything with updated versions. 
    ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

  • Need instructions for Enhanced Cable Tech "Liberty" VGA adapter....

    Hi!
    I'm trying to get my old PowerMac 8500 up and running. The only display I have that is (well, should be...) compatible is an old Apple Studio Display 15" Flat Panel (Rev B.). This is the second iteration of that display, with the VGA connection, not the earlier Mac 15 pin D-sub connection, which is what the 8500 has (http://support.apple.com/kb/SP135).
    I have two adapters that I'd think should do the trick of getting me something on the display. An NEC MultiScan unit that has several resolutions printed on it, but no adjustments, and an Enhance Cable Technologies Liberty adapter.
    The NEC one gets me noplace, and so far, neither does the Liberty.
    The Liberty has a knob with several letter stops (A-M or N), and a set of 9 (I think) DIP switches. Instructions on the back list many resolutions, but only give instructions for the last 3 DIP switches, which are for sync. It mentions to consult the instructions (which I can't find or don't have) for using the other DIP switches to get "expanded" ID codes.
    I've tried all of the knob stops, and a couple DIP switch settings, but nothing seems to get me an image on the display. The display does work, it just isn't detecting a signal, and it will tell me so.
    I think the 8500 may be going into "headless" server mode (no video) when it can't detect a monitor attached, so once it boots (and it IS booting), I can't get anything until I re-boot again. I'll have to dig up an OS9 install CD, to see if that helps me any. When I stored it some years ago, it was running Mac OS X 10.2 via a boot loader (it has a Sonnet PPC G3 processor upgrade card), so that may be an issue, too.
    But, I was hoping that maybe someone has the instructions for the Liberty adapter kicking around in their junk drawer. All I need is the instructions for the DIP switch settings.
    Regards,
    Larry W.

    Well, bought some new PRAM batteries from OWC. Installed one on the 8500/150 (also bought spares for my G4 & SE/30), zapped the PRAM several times, and still nothing. Then dug out my DVI-VGA adapter for my MBP, just to verify that nothing had gone sour with the display since I last put it in the box. All good there.
    But, it turns out that I had a solution all along in the "Accessories Kit" in the box the Studio Display came with. There was, still sealed in 16-year-old plastic, an adapter that came bundled with the display! Cut open the plastic, installed it, hooked on the display, and presto-chango, I'm watching Jaguar boot up!
    Though, Jaguar isn't so swift on this machine, even with a 250Mhz G3 processor... Might have to do with only 240MB of RAM... Once I got it back running Mac OS 9.1, though, it's a pretty snappy machine. It even reports a processor speed of 279Mhz!
    Now I can get what I need from the machine, and move it on to a new home. Also check out all the rest of my SCSI devices for data I think I need, as this is my last SCSI machine that'll take more than one internal device!
    And I may even see if I can make the Liberty adapter work like the Apple-supplied one.

  • Instructions for replacing keyboard hardware/where to buy keyboard hardware

    Hi!
    Could someone kindly recommend the best source for instructions on replacing keyboard hardware.
    And also the best place to buy the hardware?
    Specs--
    Apple MacBook "Core 2 Duo" 2.0 13" (White-SR) Specs
    Identifiers: Late 2007 - MB061LL/
    Apple MacBook "Core 2 Duo" 2.0 13-Inch (White - Late 2007/Santa Rosa) features a 2.0 GHz Intel "Core 2 Duo" processor (T7300), with two independent processor "cores" on a single silicon chip, a 4 MB shared "on chip" level 2 cache, an 800 MHz frontside bus,
    Thank you for your time,
    MacBook

    Try ifixit.com.

  • Advice needed for replacement battery for G3 12" Dual USB ibook

    I need to buy a new battery for my 12" iBook, a 600 MHz G3 model, dual USB, vintage 2001. The online Apple store has something called an Extra Battery - iBook 12.1", which is a 50-watt-hour battery. However, when I phoned the Apple store to order one the salesperson insisted that these would only work in the newer G4 version of the iBook. I queried this because there is no mention of a restriction on the processor in the description in the online catalogue, only that the machine should have two USB ports. He suggested I call the Applecare technical helpline, which I did, but the engineer there wasn't sure if the battery would be compatible either, which I find surprising since they must service and repair these machines all the time. He said it might work but there was no guarantee and the increased capacity of the newer G4 battery might damage my power adaptor, which I also find surprising. He said my machine was now too old to get a new battery. I have also looked at ifixit.com in my search for answers, which seems to suggest that the 12" iBook G3 and G4 batteries are interchangeable provided you don't mind having the wrong colour rubber foot on that corner of the laptop.
    If there is anyone from Apple who monitors these posts I would be grateful if you could give me the definitive answer about the compatibility of the iBook Extra Battery available from the Apple online store before I order one, as it would be a rather expensive mistake to make if won't work or if there is a risk it would damage my machine.
    Many thanks
    Peter

    The iBook G4's battery is absolutely fine in the iBook G3 (Dual USB). In addition to the rubber foot being a different color, the battery casing is a bit different finish, too, but it will work absolutely fine.
    http://eshop.macsales.com/shop/powerbook/battery/ibook-g3-g4-12inch/

Maybe you are looking for

  • Encrypted="true" does not encrypt MBean attribute

    Hi, I have developed a Custom Weblogic Security Service Provider. I have also created an MBean to manage my provider. One of my MBean attributes is as follows: <MBeanAttribute Name = "JdbcPassword" DisplayMessage = "The JDBC Password to the security

  • JTable Blank Rows When INSERT/DELETE in other panel with same ViewObject

    Hi, Jdev 10.1.2 JClient 2 panels based on same ViewObject in same AM One panel with Grid UI => JTable Other panel with Form UI When I insert or delete a record in the panel with Form UI and return to the panel with JTable blank rows are displayed. Th

  • Spotlight not showing files

    Have brand new iMac running 10.8.2. All going great except: 1 Spotlight will list files I search for very quickly top right but I can't get it to 'Show All in Finder', it just does nothing. It means I can't actually locate anything. 2 I've noticed si

  • Photoshop Elements 7 and 9

    1. I downloaded PSE 9 on a trial basis. I created a slide show in PSE 9 and it is in the PSE 9 catalog. When I open PSE 7 it isn't in the catalog. A search tells me there's no file by that name. I don't see any way to copy and transfer it to the PSE

  • Dreamweaver... failure to launch

    I have used Dreamweaver a few weeks ago and now when I try to open it, it doesn't. I have Creative Cloud and the other programs I am using all seem to work fine. 15" Mac powerbook 2Ghz Intel Core i7 4 GB Ram