Need MIBs for Cisco 2500 Series WLC

Hi,
I need the MIBs for Cisco 2500 WLC.
I have it for 5508 WLC. Does it works same for 2500 WLC too ?
Regards

they should be very similar.  There would be more trees available for the 5508 over the 2504.
You can get the MIBS for the 2504 from the Software downloads section of CCO.
Steve

Similar Messages

  • Hi I need OID's and the MIBs for CISCO 6504 with SUP32??

    Hi I need oids and the related MIBs for cisco 6504 with supervisor 32:
    Fanstatus notification, Powerstatus notification, Interface up/down, BGP notifications like peer down bgp established, ospf notifications
    Thanks,
    Anudeep

    Fan status
    CISCO-ENV-MON mib
    "ciscoEnvMonFanStatusEntry"          "1.3.6.1.4.1.9.9.13.1.4.1"
    "ciscoEnvMonFanStatusIndex"          "1.3.6.1.4.1.9.9.13.1.4.1.1"
    "ciscoEnvMonFanStatusDescr"          "1.3.6.1.4.1.9.9.13.1.4.1.2"
    Power
    ciscoEnvMonSupply
    S
    tatusEntry"          "1.3.6.1.4.1.9.9.13.1.5.1"
    "ciscoEnvMonSupplyStatusIndex"          "1.3.6.1.4.1.9.9.13.1.5.1.1"
    "ciscoEnvMonSupplyStatusDescr"          "1.3.6.1.4.1.9.9.13.1.5.1.2"
    "ciscoEnvMonSupplyState"          "1.3.6.1.4.1.9.9.13.1.5.1.3"
    "ciscoEnvMonSupplySource"          "1.3.6.1.4.1.9.9.13.1.5.1.4"
    Interface
    IF-MIB
    ifAdminStatus  1.3.6.1.2.1.2.2.1.7
    ifOperStatus   1.3.6.1.2.1.2.2.1.8
    BGP
    BGP4-MIB
    for the rest i will leave it to you to find the exact OIDs
    use this link to find other mibs that may interest you
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=BGP&translate=Translate&submitValue=SUBMIT&submitClicked=true

  • Security License for Cisco 3900 Series

    Hi,
    I am having    Security License  (SL-39-SEC-K9)  for Cisco 3900 Series router, Can somebody help me to provide sample config to configure 3945 router to act as firewall. Is there any difference with the native IOS based firewall config..
    Regards,
    Mukesh           

    Here is a detailed instruction on ISR G2 licensing (including downloading, installing, rehosting license, etc.).
    Usually, you just need to go to cisco.com/go/license, enter PAK and follow detailed instructions.
    HTH
    Alexandr

  • Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

    Hi All,
    Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
    Any help would be greatly appreciated.
    Thanks in advance.
    Samir

    Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices.  RME will only use HTTPS to fetch VPN concentrator configurations.

  • Error in Cisco 2500 series Wireless Controller

    I have this error in Cisco 2500 series  Wireless Controller 
    The AP type Cisco AIR-CAP35021-A-K9
    I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series  Wireless Controller  But the AP get ip .
    Please can any on help me . 
    Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 

    Duplicate posts.  
    Go here:   http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller

  • Cisco 5500 Series WLC Field Recovery Compatibility

    Is Software Version 7.2.111.3 compatible with Field Recovery Image Version 7.6.95.16.

    Duplicate posts.  
    Go here:  http://supportforums.cisco.com/discussion/12154556/cisco-5500-series-wlc-field-recovery-compatibility

  • IOs for cisco 1900 series router

    Hi,
    Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
    Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
    Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
    Cisco IOS System Timers Remote Overflow (CSCei61732)
    Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
    Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
    Cisco IOS Telnet Service DoS (CSCef46191)
    Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
    Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
    Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
    Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
    Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
    Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
    Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
    Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
    Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
    Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
    Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
    Regards,
    Bala

    Hi,
    The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
    Regards,
    A.Bala
    leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
    >Balakrishnan Appavu,
    >
    >A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
    >
    >https://supportforums.cisco.com/message/3277195#3277195
    >
    >Author : leolaohoo
    >Profile : https://supportforums.cisco.com/people/leolaohoo
    >
    >Message:

  • Need SAMI for Cisco 7604

    Hi,
    Can anyone suggest me a SAMI module that supports IKEv2 Configuration Payload for Cisco7604 ?
    Does this suffice ? WS-SVC-SAMI-BB-K9 (Or) I need to go for MEM-SAMI-6P-2GB ??
    Thanks
    Krishna

    they should be very similar.  There would be more trees available for the 5508 over the 2504.
    You can get the MIBS for the 2504 from the Software downloads section of CCO.
    Steve

  • MIB for Cisco 15302 ONS

    Hi,
    Our Cisco ONS 15302s (SystemObjectId 1.3.6.1.4.1.7546.1.5.1.1.2) are issuing traps for enterprises.7546 as well as containing more MIB entries for enterprises.89 than I can find MIBs for......:-(
    I have been unable to find MIBs for these traps (or the specific Supported MIB "ONS 15302 MIB" mentioned in some cisco documents) either on Cisco's web site or elsewhere.
    I'd much appreciate if someone could direct me to the specific MIB for this device type?
    TIA.

    Thanks for the info but it doesn't cover the key part. I have downloaded all the v1 and v2 MIBs and scanned them for the enterprises number but without success.
    The message we receive is below. The key part is the event for enterprises-7546. This seems to be an Axxessit component of the node reporting the event. As mentioned the node is an ONS15302. Cisco refers to the ONS15302 MIB but it is not in the ftp area.
    - Normal Sun Jul 18 01:58:21 offshore-node-a.offshore-domain Received event .1.3.6.1.4.1.7546.1.5.1.2.9.1.0.4 (enterprise:.1.3.6.1.4.1.7546.1.5.1.2.9.1 generic:6 specific:4),
    no format in trapd.conf. 10 args:
    [1] private.enterprises.7546.1.5.1.2.8.2.2.1.0 (Integer): 0
    [2] private.enterprises.7546.1.5.1.2.8.2.2.2.0 (Integer): 0
    [3] private.enterprises.7546.1.5.1.2.1.2.9.0 (Integer): 1
    [4] private.enterprises.7546.1.5.1.2.1.2.10.0 (Integer): 10
    [5] mgmt.mib-2.system.sysDescr.0 (OctetString): ONS 15302
    [6] mgmt.mib-2.system.sysObjectID.0 (ObjectIdentifier): private.enterprises.7546.1.5.1.1.2
    [7] mgmt.mib-2.system.sysUpTime.0 (Ticks): 36707509
    [8] mgmt.mib-2.system.sysContact.0 (OctetString):
    [9] mgmt.mib-2.system.sysName.0 (OctetString):
    [10] mgmt.mib-2.system.sysLocation.0 (OctetString): Offshore node A

  • How to find useful MIBs for Cisco Devices?

    Hi,
    I am setting up a new Monitoring System (CA Netvoyant). It has some default Cisco monitoring capabilities ( I believe these are soem standard MIBs).  I am wondering how can I add more useful Cisco MIBs for the devices I have in my network. There are thousands of MIBs and it looks like it is not easy at all to find the useful ones.
    For example the MIBs that can give you Emergency and up to warning level information, cpu, memory, interface errors, module failures (in case of Cat 6500), FWSM, BGP, VPN tunnel status notifications. Is there a list of useful MIBs for each device type, like Cat 6500, ASA5540, Cat 3750-E etc depending on IOS Image?
    Any help in setting up the SNMP monitoring system would be really helpful.
    Thanks

    If there is a MIB for it, most SNMP Capable Management servers can poll them.
    This can be such as FHRP states, Routing Peers, ASA Failover status, Seriel numbers for inventory purposes.
    The potential is almost endless, it just depends what you should monitor to ensure you are in the know when your network hiccups.
    Here is a link to the IOS MIB Viewre    
    http://tools.cisco.com/ITDIT/MIBS/MainServlet
    CCNP, CCIP, CCDP, CCNA: Security/Wireless
    Blog: http://ccie-or-null.net/

  • Converting Autonomous AP to LWAP by using 2500 series WLC

    Hello everyone,
    I'm a newbie in wireless section and have a problem. I have two autonomous AIR-LAP1041N-E-K9 with IOS "c1140-k9w7-mx.124-25d.JA1" and one 2504 WLC. I need to convert those APs to Lightweight and use with that controller. But, I don't have any power supply for APs and PoE switch. I only got 2504 WLC with 2 port PoE. If I could use WLC's ports as switchports, this will be really easy. Maybe it could be used, but as I see WLC's ports are L3-only.
    What is the easiest way to solve this issue?
    Thanks now,
    Mehmet.

    I don't know if that is possible, but you can try. Configure the WLC and then connect one of the AP's to the PoE port. Configure the AP through the command line via the console. Put that ap on the same subnet as the WLC management. Try to ping the WLC IP address from the AP. If that works them your good so far. Now connect a laptop to another port and configure the IP on the laptop to also be on the WLC management. Make sure you can ping the AP from the laptop and vice versa. Then you have to download the code for the AP which will be an rcv image. Follow these links on the conversion.
    Using a TFTP Server to Return to a Previous Release
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    https://supportforums.cisco.com/docs/DOC-18268
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    http://www.youtube.com/watch?v=QQ_NuxdRhQ4
    https://supportforums.cisco.com/docs/DOC-14960
    Sent from Cisco Technical Support iPhone App

  • Scripting reboot for Cisco 300 Series switches

    I would like to have some help putting together a script for rebooting our 300 series POE switches. I have about 150 at this stage to administer and it would make it much easier not to have to remotely reboot them. The IP settings will be the same for each location and we have about 2-5 in each location. I will be logging in through logmein to each remote server, and will run the scripts from this to the local switches. Any help would be appreciated.

    I was playing with my Indigo on an SG-500 and it seems to work.  Create a session for each switch and in the session properties for each switch enter your crendentials (user/pass) IP/port, etc, I was using telnet, port 23 for this and then under the send command tab, on connection I entered:
    reload
    y
    One command per line up to 20 commands I believe and it connected, I saw my prompts and replies and then shutting down.
    So if you try this you can just go down the file tree list for switches with cameras than need a reboot and restart the entire switch if you like, quick and easy.
    You could also add a folder for each switch and a session in that folder possibly for each camera/port with online port number changing for each camera in the session properties and then selectively cycle power for just the affected cameras.
    Example for port 22/camera xxxx:
    conf t
    int gi22 
    power inline never
    power inline auto
    It would take a fair amount of time to set up but once done you could just pick a switch folder and the port in that switch to cycle.  If you have multiple port on a switch you could use
    conf t
    int range gi22-24
    or 
    int range gi1,6,16,20
    power inline never
    power inline auto
    might have to verify that syntax

  • Need drivers for palm m500 series for Vista 32 bit

    Where can we find driver downloads for my husbands palm m500 series for 32 bit Vista??
    Thank you!!
    Don
    Post relates to: Palm m500

    Try reading through this thread in the Windows Hotsync section of the Forum:
    http://forums.palm.com/palm/board/message?board.id=windows_hotsync&thread.id=38625&jump=true
    WyreNut
    I am a Volunteer here, not employed by HP.
    You too can become an HP Expert! Details HERE!
    If my post has helped you, click the Kudos Thumbs up!
    If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

  • Need help for CISCO RV042

    We have four internet line. Two are dial up using with PPPOE 5 mbps each. And two more of 5 and 2.5 mbps respectively coming out from BSNL modem and can directly connect to LAN port. Now we would like to connect all lines with RV 042 load balancing router to have optimum speed. Pl. guide how to do it?

    Stoyan,
    Post limit more specific questions so we can assist. This router is really straight forward if you get stuck at a point please post a question.  Forwarding rules are under setup tab, if you plan on using one to one nat its right beside forwarding and for DHCP/DNS for lan. The next tab over. If you are going to be using dual wan load balancing then you want to set up protocol binding/outbound for HTTP and HTTPS.
    Thanks
    Jasbryan
    Cisco Support Engineer
    .:|:.:|:.

  • 2 x Cisco 4400 series WLC to provide redundancy

    Hi all,
    can any one point me in the direction of some resources so that I can get a better understanding of configuring 2 4400's in a redundancy group?
    I've got experience with the HP wireless module kits in a redundancy group, any one know whether the cisco stuff works in the same sort of way??
    Mario

    Here are a few docs that should help.
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008064a294.shtml
    http://www.cisco.com/en/US/docs/wireless/controller/6.0/configuration/guide/c60mobil.html

Maybe you are looking for