Need spartan 3e driver for LabVIEW FPGA 2011

Hello,
I'm looking for Spartan-3E driver for Windows 7 LabVIEW FPGA 2011.
Thank you

Thank you for all the helps. I do appreciate that.
By the way, I'm wondering the latest driver on NI is used for Labview FPGA 2012 or 2012sp1?
Just in case our department would purchase the latest version of Labivew in the near future.
Thank you again and have a nice day.

Similar Messages

Need SPARTAN 3E board Driver for Labview FPGA 8.5 !!!!!! Thx

HI!!I need the spartan 3e driver for labview 8.5(not for labview 8.6) for school useI try to download it from ftp://ftp.ni.com/outgoing/NISPARTAN3ELV85.zip
but this link is dead now. Could somebody send this driver to [email protected] PLZ? Thank you a lot for all in advance
Solved!
Go to Solution.

Hello,
I'm looking for same (Labview FPGA 8.5 for Spartan 3E). But it isn't available on related url now. I'll be glad if someone can help to find driver.
Best regards,

C API version required for LabVIEW FPGA 2011

What is the verison of the C API that will work with LabVIEW FPGA 2011?
Solved!
Go to Solution.

I would guess this one: http://www.ni.com/download/fpga-interface-c-api-2.0/2616/en/
The version numbers appear to start with years in 2012. This is the highest version I could find before 2012 and it was released in August of 2011. That time coincides with the annual NI Week festivities where a large portion of the software/hardware is released. It's a small download so it shouldn't be difficult to download and try it out.
But, you'll still need LabVIEW for FPGA development according to this white paper: http://www.ni.com/white-paper/9036/en/

Need a HP3421A native driver for labview 5.1

Hi,
I'm looking for a native HP3421A driver for labview 5.1. Of course I searched in the "Instrument Driver Network" but I foundd only drivers for labview 6.0 and 7.0 or greater.
According to this document: http://www.ni.com/pdf/manuals/321691a.pdf#search=%22labview%204.x%20hp3421a%22 there is a such driver for labview 4.x.
Any idea where I could find this driver for labview 5.1 ? A haven't any "Instrument Driver Library CD-ROM".

hi there
the driver he is searching for can be found here (LV 7.0): https://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E969E659CE034080020E74...
the driver uses the old school GBIP functions, so it should be possible to downgrade it down to LV 5.1. do downgrade open the "HP 3421A Example.vi" and choose
File->Save with options->Save for previous.
since you only can downgrade to the next prior version of LV you need a ladder of LV versions, but i'm sure that if you ask here you'll find someone who can do this for you.
Best regards
chris
CL(A)Dly bending G-Force with LabVIEW
famous last words: "oh my god, it is full of stars!"

IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?

IS CLIP supported by Xilinx Spartan3E driver for LabVIEW 8.6?
For HDL interface node, the enable chain and multi clock domain is difficult to understand
Solved!
Go to Solution.

Reidl,
Thank you for your answer. How do I uninstall my current version? I have looked in "Add or Remove Programs," but I don't see anything under "Xilinx" or "Spartan." I do see an entry for "National Instruments Software." However, when I click "Change / Remove" I don't see any entries for the Spartan Board.
I tried running the installation program, and I received the following message:
The NI LabVIEW FPGA Support for Spartan-3E 1.1.0 installation has failed with the following error.
You have a higher version of NI LabVIEW FPGA Support for Spartan-3E in your system. You must uninstall it before installing this again.
What is the latest version number? How do I check what version I currently have?
Thanks,
James Carroll

Hard Drive for a MID 2011 MACBOOK AIR 11 INCH

Do you have a recommendation for online purchase of a new Hard Drive for a MID 2011 MACBOOK AIR 11 INCH??
Thanks

Here is another vendor that sells MBA storage upgrades:
http://www.transcendusa.com/apple/jetdrive/
Ciao.

Hp driver for labview for hp8156a attenuator

I am looking for a hp8156a driver for labview. There is not one posted in the driver section of this site. Thanks

Here is a link to the programming manual. Section 8 shows the commands. It will take some work, but you can write your own drivers.
http://www.home.agilent.com/upload/cmc_upload/All/opat0500.pdf
Message Edited by unclebump on 07-12-2005 04:21 PM

HP 54501A - Instrument Driver for LabView v.7 or v.8

Hi all,
I'm looking for HP 54501A - Instrument Driver for LabView v.7 or v.8. I have NI gpib/usb controller installed, but cannot control the scope via Labveiw.
The link I found at NI web site within drivers section seems to be broken so I couldn't download it!
Please, anyone, suggest/help!

The link you were given works for me. You can try it again. The given link brings you to a page where the CVI and LabVIEW drivers are listed. the direct link to the LabVIW driver is http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9455659CE034080020E748... .

Is there compatible motion driver for LabVIEW 8.6?

Is there compatible motion driver for LabVIEW 8.6? The latest motion driver seems to be 7.6 and it only support up to LabVIEW 8.5...

If you buy LabVIEW 8.6, you will also get 2008 August Driver CD.
NI-Motion 7.7 driver should be included in it.
Or you can wait for a while.
I guess NI will put on Web these days.

Aeroflex 2975 driver for LabVIEW 8.0

Is there a way to convert the Aeroflex IFR 2975 driver for LabVIEW CVI for use in LabVIEW 8.0? OR, is there a driver already developed for this?

Frank,
I am using the LV 7.1.1 version of this CVI driver in an application I wrote. We should be able to recompile this for 8.0. Basically as I explained with no handshaking the instrument falls out of sync with the controlling computer. Basically the only GPIB command that is supported in that driver is *IDN?. So what I have done is after other calls I use this command and compare the return string to see if it is what I expected. If not I use a popup telling the operator that a GPIB error occurred and to reboot the IFR to clear the bus. I also have instructed the operator to run NI Spy in the background...this seems to cut down the occurance of these errors. Another way to clear the bus that is faster and usually works is to stop the application, and read the bus using MAX until you see a timeout when there is no more data available( usually twice). Then rerun the application. Depending on the application this might be a work around though not an elegant one.
Since the driver was converted from a CVI driver it uses the call library function node. This does not allow us to control the timing between the Write functions and Read functions. If you are doing something that is relatively simple you could use the TCL command set and VISA to write a driver. Just put a wait function between the Write and Read function and experiment with the timing until it looks like it won't fail. I've considered doing this myself but have been hoping that they will actually make the instrument 488.2 compliant. I am assuming that the actual error is that the data buffer is being read by the controller before the instrument is finished writing to it. The other scenario is that the data buffer might not actually be getting flushed every time it is read. I'm hoping my first assumption is correct or they have even more problems with the instrument.
In January of '05' they actually enabled the following commands *SRE xx, *SRE? and *STB?. I recently wrote a simple vi to see what happens to the Status Byte after using IDN? command and reading the data buffer. The MAV bit begins logic low, then goes hi when the data is available. After reading the data (i.e. "IFR Systems, 2975.....) I again query the Status Byte. The MAV bit is still in a logic hi state. I sent screenshots of the front panel and block diagram as well as the .spy files to them. All was heavily notated and they said they were going to look at it. If anyone is interested in this I can post this code as well.
Using LabVIEW 2010SP1 and TestStand 4.5

Looking for HP 5371A driver for Labview 6.1?

want to communicate with HP5371A by PC over GPIB port

I think that device is too old for finding a driver for labview. If you have all the GPIB command, it's easy to program. I made it for another type of instrument.
Benoit Séguin
Software Designer

Need an instrument driver for Stahl product

Hi guys!
I need an instrument driver for the coil temperature measurement device ER-230.01B (company Stahl)!
Does anybody of you have this driver?
I have already searched in the NI Driver list and couldn't find it.
Thx,
Nobby

Hi Nobby_83,
Unfortunately we don’t have the driver for your Stahl device. You have to contact Stahl to know if they have the driver.
http://www.stahl.de/en/start.html
Benjamin R.
R&D Software Development Manager
http://www.fluigent.com/

I need an audio driver for Yoga 13 with Windows 7 Pro 64 bits English

Hi all,
I downgraded my Yoga 13 from Windows 8 to Windows 7 pro 64 bits, and ever since then I have a problem with my microphone.
Skype finds the microphone and can use it, calls are all working fine, but any other program using audio does not work with the microphone.
After troubleshooting, I concluded that I need to update the driver but I cannot find it. Anything that I find on the Lenovo support pages does not install (event the one found on this page: http://support.lenovo.com/fr/fr/downloads/ds002860).
After looking at this post: http://forums.lenovo.com/t5/Idea-Windows-based-Tablets-and/I-need-an-Internet-driver-for-Yoga-13-wit.... I figured I would to be provided with the link by someone from Lenovo support.
Here's the hardware ID of the soundcard: HDAUDIO\FUNC_01&VEN_14F1&DEV_506E&SUBSYS_17AAA001&REV_1000. In Windows it is recognized as High Definition Audio (in the device manager).
Thanks a lot for your help.

Hello,
From looking at the Yoga 13 Hardware Maintenance Manual and downloading the driver package from the Realtek Wireless LAN & Bluetooth Driver for Microsoft Windows 8 (64-bit) - IdeaPad Yoga 13 page and extracting (but not running) it to look at the contents, it appears the Yoga 13 uses a wireless LAN card based on Realtek RTL8732 chipset.
I would suggest that you try downloading the drivers, expanding, but not installing them on to a USB flash drive or SD card, then plugging that into the Yoga 13, running the Device Manager (filename: DEVMGMT.MSC), clicking on the appropriate entry for the wireless network adapter, selecting update, and then choosing the Browse my computer for driver software option, pointing that to the location of the unpacked drivers. Perhaps Device Manager will find the correct drivers to install that way.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

DCT for Labview fpga

Hi,
I have problems based on dct for labview fpga. I get the project example from this link https://decibel.ni.com/content/docs/DOC-8202. I run the project in labview and its run succesfully. After that, I try to use a different vhdl code for the CLIP (in labview) that I get from open cores (http://opencores.org/project,dct_idct). I rewrite the fpga.vi by inserting a new vhdl code in the CLIP. When I run the project, there are no errors. However, the compressed image is not display. I check the output values from the Read from FPGA block at the host.vi and it shows zero values at all time. I try to debug, but still don't get the solution. Anyone expert please help me. Thanks in advance.

Hey Troy,
Have a look at the attached front panel design that will be compatible in FPGA.
Hopefully it helps!!
Aashish M
Applications Engineer
National Instruments
http://www.ni.com/support/
Attachments:
FPGA_CALC.vi ‏22 KB

I need the correct driver for an infrared remote control (ENE CIR receiver) for Pavilion DV4-2173nr

I need the correct driver for an infrared remote control (ENE CIR receiver) for Pavilion DV4-2173nr.
The receiver that came with my notebook is a black model one (see picture below), with the following information in its bottom label:
RC1762302/00
3139 228 50021
HP SPS: 435743-001
HP: HSTNN-PRO7
RC6 ir
CP06 60808 A 146218 REV. B
I never managed to make it work, from the very beginning. I know it is working, because I replaced the battery for a brand new one and it shows a blinking IR LED when I press any button and point it to a digital camera.
Searching for "ENE CIR receiver driver" is useless 'cause I received more than one hundred answers - I tried four of them but none worked so far.
So, instead of trying the whole bunch, I am crying for help - could someone please tell me which driver is the correct one for this remote model?
Thanks in advance and regards,
Mike
P.S.: I am using Windows 7 Ultimate 64-bit and Ubuntu 12.04 in this notebook

http://ftp.hp.com/pub/softpaq/sp46501-47000/sp46741.exe
File name:
sp46741.exe [1/1, 1.04M]
System requirements:
No additional prerequisites
Released:
2009-12-31
Version:
2.7.4.0 A
Compatibility:
Microsoft Windows 7 (32-bit), Microsoft Windows 7 (64-bit)
Fix/Enhancement:
Original Software/Drivers

Need spartan 3e driver for LabVIEW FPGA 2011

Similar Messages

Maybe you are looking for