Need step by step to get port 48705 open for Panasonic Bluray

Classic handoff syndrome. Brand new Panasonic Bluray connected to internet out of the box with Airport Extreme, streamed fast. Imac running Snow Leopard.
Updated Panasonic firmware and no connections. Panasonic tech tried for a half hour and concluded that I needed my ISP to open port 80, 443 and 48075. I think that 80 and 443 are open by default. Resetting the settings and the player did nothing....gateway: fail. There is no way to undo the firmware update.
Call India and Verizon says that they cannot assist me with AEBSn just Verizon routers. All searches for this problem give directions with too many blanks that I don't have the info to fill in. Below is an example of an attempt in the community to help. I wouldn't know where to find the <missing info> . I couldn't find the port mapping tab in this version....help would be appreciated.
Tesserax
Re: how can you perform a Port Forwarding Procedure on Ports 48705, 443 and 80 so my Blu Ray player will be able get and IP address and connected to your gateway.
Oct 1, 2011 11:22 PM (in response to doc9850)
Again, you would only need to configure for port mapping if you intend on accessing the Blu-ray player from a remote location.
Port mapping takes two basic steps:
Either assign a static Private IP address or use the AirPort's ability to allow DHCP to assign a reserved IP address to the Blu-Ray player, and
Configure the AirPort, using the AirPort Utility, for the proper ports to map.
The following are the basics for setting up one of the newer 802.11n AirPorts for port mapping/forwarding: AEBSn - Port Mapping SetupTo setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings: 1. Reserve a DHCP-provided IP address for the host device.AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
Description: <enter the desired description of the host device>
Reserve address by: MAC Address
Click Continue.
MAC Address: <enter the MAC hardware address of the Blu-ray player>
IPv4 Address: <enter the desired IP address>
Click Done.
2. Setup Port Mapping on the AEBSn.AirPort Utility > Select the AEBSn > Manual Setup >Advanced > Port Mapping tab
Click the "+" (Add) button
Service: <choose the appropriate service from the Service pop-up menu>
Public UDP Port(s): <enter the appropriate UDP port values>
Public TCP Port(s): <enter the appropriate TCP port values>
Private IP Address: <enter the IP address of the Blu-ray player>
Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
Click "Continue"
AirPort Utility Port Forwarding for AE is not an intuitive app. It is version 5.6.1 which is up to date for SL.
http://www.google.com/search?client=safari&rls=en&q=48705+port&ie=UTF-8&oe=UTF-8 shows that other people are needing to do this with various routers.
The player is Panasonic DMP-BDT500 Integrated Wi-Fi 3D Blu-ray DVD Player
FYI, the player plays disks beautifully.
Thanks for any help.
David

My problem seems to be that my AirPort Utility does not have Port Mapping under the Advanced Tab.
This tells us that you have another router "upstream" on your network, which you may call your modem, but it is in fact a modem/router or gateway type of device.
The AirPort Extreme is configured correctly in Bridge Mode to work with this type of device on your network.
You can verify this by clicking the Internet icon, then clicking the Internet Connection tab. You will see that the setting for Connection Sharing is set to ""Off (Bridge Mode)". That means that the AirPort is not providing the routing services for your network.
Your modem/router or gateway is the device that will need to be configured for port forwarding / mapping.....not the AirPort Extreme.
I am sure that Tesserax will have similar comments.

Similar Messages

Which port is open for connection ?

how could I know which port is open for connection ?
In the java, I use JDBC to connect to Oracle,
connection = DriverManager.getConnection("jdbc:oracle:thin:@localhost:1521:sid", "scott","tiger");Do we have a command to show open port ?
Thanks.

What is your Oracle version, and do you use dedicated connections or "shared servers"? From your port number invoked (1521), I'll guess you use dedicated connections. In that case, the listener (located at 1521) will "spawn" a dedicated process for your session, and tell this process to start on another port (usually falling on a certain range, depending on your OS). An easy way to see this would probably to turn listener tracing on. Here's what I found in the log file after I started a new (dedicated) session on my 10.2 DB:
"22-OCT-2006 21:31:16 * (CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=ora102)(CLIENT_REGISTRATION=ora102)(CID=(PROGRAM=C:\oracle92\bin\sqlplusw.exe)(HOST=DANIELROYLAPTOP)(USER=Daniel))(CLIENT_REGISTRATION=ora102)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.100)(PORT=3198)) * establish * ora102 * 0"
HTH
Daniel

Should FTP port be opened for client_to_as function

I need to transfer a file from the client machine to the Solaris Server where the 10g forms are running. I was planning on using the webutil_file_transfer.client_to_as function. I know we have to set some properties in the webutil.cfg file. Other than that, should the FTP port be open on the server for the file to be transferred from the client machine. Basically, wanted to know if FTP protocols are used to transfer the file so that certain securities can be set on the server.
Also does anyone know how to delete the file on the solaris server programmatically through Oracle Forms? After the file is transferred from the client to the server and processed, I need to delete the file. I am assuming you can use the HOST command, but not sure of the exact syntax and what permissions are required to delete the file from the client machine.

I have never used the "Client_To_AS" method, however, according to the documentation all you need to configure is the webutil.cfg and insure the transfer.appsrv.enabled parameter is set to TRUE and if the transfer.appsrv.accessControl parameter is set to TRUE then you also need to ensure the target directory on the App Server is listed in the transfer.appsrv.write list. There is no mention that FTP must be enabled on the App Server.
The documentation also states that you should call the WebUtil_File_Transfer.IsASWritable function with the target file name to ensure you are able to write to the file location on the server.
As to how to delete a file, you can use the "rm <filename>" command in Solaris to remove the file. Also, here is the link to the documentation I used to reply to your post.
http://www.oracle.com/technology/products/forms/htdocs/webutil/web_util.pdf
Hope this helps.
Craig...

Trying to figure out why ports are open for systemd processes

Output of my "netstat [root@server ~]# netstat -nlp
Active Internet connections Proto Recv-Q Send-Q Local Address tcp 0 0 0.0.0.0:22 tcp 0 0 127.0.0.1:3306 tcp 0 0 0.0.0.0:5355 tcp6 0 0 :::80 tcp6 0 0 :::22 tcp6 0 0 :::443 tcp6 0 0 :::5355 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 IP4:68 udp 0 0 127.0.0.1:123 udp 0 0 0.0.0.0:5355 udp6 0 0 ::1:123 udp6 0 0 :::5355 raw6 0 0 :::58 Why are ports 5355, Please let me know -nlp"
(only servers)
Foreign Address State PID/Program name
0.0.0.0:* LISTEN 2159/sshd
0.0.0.0:* LISTEN 2060/mysqld
0.0.0.0:* LISTEN 2168/systemd-resolv
:::* LISTEN 4460/nginx: master
:::* LISTEN 2159/sshd
:::* LISTEN 4460/nginx: master
:::* LISTEN 2168/systemd-resolv
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 2078/systemd-networ
0.0.0.0:* 4491/ntpd
0.0.0.0:* 2168/systemd-resolv
:::* 4491/ntpd
:::* 2168/systemd-resolv
:::* 7 2078/systemd-networ
58, and 68 being listened to/open ?
if any additional information is needed, it is the latest version or arch linux and fully updated as of this post.

68 is for BOOTP/DHCP. Why it needs so many open is beyond me - dhcpcd just has the one global 68 open for any amount of interfaces.
The other two ports don't look like anything network setup related should have open.
I would file a ticket with systemd upstream.

I cannot get icloud to open for my feddly pro. I apid for feedly pro on my desk top and now I cannot use it on my other devices

I cannot open icloud with my feedly pro. I set up my account on my desk top and now cannot get it to open all of the blogs on my other devices

Feedly Pro has absolutely nothing to do with iCloud.
Contact Feedly if you're having problems with their product.

Hardware issues on iPhone that would qualify for a free replacement under the warranty, however I recently accidentally damaged the digitizer and now need to pay £177 to get it repaired just for them to send me a replacement phone anyway!

Okay here is my problem: I bought an iPhone 5c about two months ago, and recently knocked it in my pocket and damaged the digitiser – although not the glass, but it is currently unusable. However before that it started really playing up.
Primarily, it stopped being able to tell the time – which does not sound like a big issue, but is in fact a real pain as it throws out all my real-time apps, as well as making all my messages come through completely out of sync with each other. The time just seems to have slowed down, no matter if it is on ‘Set Time Automatically’ or ‘Set Time Manually’ – in half an hour it normally only forwards two or three minutes. Then the Bluetooth would not work, and then the same with the wifi – they just sat there with the turning on icon staying on and not changing. The next thing that happened was that my messages that I’d sent to people would occasionally send to other contacts over imessage completely randomly without me doing anything!
I know these are hardware issues and covered by Apple’s warranty, and they would replace my iPhone if those were the only problems, but as the digitiser is cracked I have to pay £177 pounds before they will even look at it to replace the glass, and that is just so I can send it off again afterwards for them just to give me a fresh phone anyway!
It is also not an option to do a self repair or go to a phone doctor as both of these will use non-apple parts, and void my warranty.
I really am stuck as I don’t have that kind of money for a repair at the moment, and still feel like it would be a complete waste of time for a phone that is currently not working anyway that they would just replace. Is there anything I can do?

"Is there anything I can do?"
Yes, you can exchange the handset for a refurbished out-of-warranty product for £216.44 (includes shipping + VAT). Treat your objects like women - with love, and respect.

What ports to open for iChat for video

I can't video chat when I'm connected to my D-link WBR-2130 Wireless G router. I know that the problems lies within the router because if I connect my computer from ethernet to my modem it works fine.
I believe the problem is just that I need to open up some ports. I had a list that someone gave me but I can't find it right now. So can I get a ports listing to open up and have the router work?
Is there anything else I could be missing so I don't need to come back and say it didn't work?

Try turning the SPI or DOS firewall setting on the WAN page Off as well.
It is a Check to Disable this item.
Save Settings.
In my DG834G I only made sure it did UPnP (Default) and changed the DOS (on Mine) to Off and allowed the Responding to Internet Pings.
My Allow and Block settings were the same as yours.
I did have Bonjour problems with one computer on Leopard and the other on Tiger that I was not able to resolve until both were on Leopard.
10:01 PM Friday; April 18, 2008

Which ports to open for registering an iPod Touch OTA via proxy / firewall ?

I need to set up some iPod Touch over the air via a wifi network controlled with a firewall. I get a message "unable to connect registration server". I suppose I have to open ports, but which ones ??

Try here:
http://support.apple.com/kb/ts3297
http://support.apple.com/kb/TS3125

Ports to open for Jabber to work

Hi,
I want to know which ports I should allow on ACL which will allow Jabber on iOS and Android devices to work successfully.
Thanks,
Kashish

Hey Kashish,
As far as I know, Cisco Jabber for Android and iPhone share the same port utilization:Port and Protocol List
Regards,
Jas

Where's a smart person when you need one? My iphoto just will not open for no reason at all(I REALLY NEED HELP)

I have not done anything strange like changing something in my computer or IPhoto. One day it just decided not to open. I dont have my photos backed up from IPhoto and I really need the photos on there and Iphoto itself to graduate in two weeks.
I will click on Iphoto and it'll jump twice, open but it will be totally blank white and immediately have the spinning rainbow wheel and it never loads. I'll then put my mouse over the icona nd it'll say "IPhoto not responding" and everytime I have to force quit. I really dont understand what happened.
I have googled for days variations of "My Iphoto will not open" and none of what people are saying helps at all because all of them have done something to mess up their apps. I really really need help, please, its got to be something so simple because I didnt change anything on my computer.

As a Test:
Hold down the option (or alt) key and launch iPhoto. From the resulting menu select 'Create Library'
Import a few pics into this new, blank library. Is the Problem repeated there?

Ports to Open for SDM Deployment thru NWDS in VPN

Hi,
We are trying to deploy WD components over VPN. In this scenario what all ports should be open.
Would opening the message server port suffice ? Or is it necessary to open the SDM port too ?
Will deployment happen through Message Server or directly through the SDM port.. ?
Regards
Bharathwaj
Message was edited by: Bharathwaj
Bharathwaj Ragothaman

Hi,
If u r connected to VPN, automatically u r into their network. So it is enough that ur application server is up and running.
In windows>preferences>SAP J2EE Engine. Give the host name and the port.
Just deploy ur application it will be asking for the password. Give the SDM password.
- Nagarajan.

I cant get "comments" to open for NRO,breitbart or Newsbusters !!

when i clk on comments or to post one on these websites...my pc scrolls to the bottom of the article and its blank.

If you use avast! security software, please see this thread: [https://support.mozilla.org/en-US/questions/975592 Disqus and other comment boxes no longer appear.]

Why after your latest update do I keep getting multiple tabs opening for CoolPreviews, Video DownloadHelper, my iGoogle homepage, and the Thanks for Downloading Firefox 5.o?

I've already downloaded the latest Firefox more than a week ago, and now, every time I open Firefox, all these tabs pop up (4 of them)...before that, a window comes up checking the compatability of all of my add-ons, with the status bar filling up as it does so, before the browser shows up.
I have not changed a thing in the browser like resetting a new home page, changing an options with ANY of your add-ons, etc...just these annoying tabs all showing up every time I click on your browser. I tried Chrome and it comes up in a flash with NO PROBLEMS, which I think I'm going to go use now!

As you can see below, when I right click, I have no such option. In the User Account Settings, I'm operating as the "System Administrator".
Any other suggestions?

I cannot get Firefox to open for the past three days--help?

When I click on the Firefox icon, the page comes up, but then there is an error--says page can't load, etc., etc. I have uninstalled Firefox, and reinstalled it, but nothing seems to work. Any suggestions?

I tried your suggestion of pressing the shift key while launching Firefox. What happened is, this action highlighted in blue several icons on my desktop including Windows Internet Explorer.It then preceded to open Windows Internet Explorer. It was worth a try. I tried the control key while trying to launch FireFox and that did not do anything.

How do you configure the set of port to use for FTP passive data connection

I was able to start the ftp server xml db and connect to it locally. When I tried to connect to it from home, I was able to log in but when i do a "get" command the sessions hangs. I also tried passive mode and do a "get" command and it gives me a connection refused error. I am using the default port 2100. I think this might be a firewall issue with the data connection port. I am not sure which range of ports to open for the passive ftp connection on the server side or where to go and set them for for the ftp server to use? Or this issue might not be firewall related??? Any thoughts. Thanks.

This is a typical problem with VPN/Firewall software and FTP on ports other than 21.
When you open the FTP data connection the FTP Server identifies which port the data will be sent on using the PORT command which is sent on the command port (typically 21 with a normal FTP server, 2100 by default with XDB). THe client then opens that PORT to accept the data (file, output of an ls etc).
As I understand it most VPN/Firewall are configured to monitor 21 for 'PORT' requests. They then understand to allow connection on the PORT number passed on the command PORT. Hence with Port 21 firewall / VPN software is not a problem. However since the XDB command PORT is something other than 21 they do not see / honour the PORT commands from the server and hence the client cannot open the data connection on the specified PORT
As to how to solve it, I wish I knew (After 5 years I still can't use XDB FTP from home to a machine in the office once the VPN tunnel is open :( ). I'm sure it's going to be firewall / VPN software specific and may need the VPN servers to be configured.
The best bet would be to run the FTP server on 21...
Add the following line to your listener.ora file
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP) (HOST = hostname) (PORT = 21))
(PROTOCOL_STACK = (PRESENTATION = FTP) (SESSION = RAW)))
and then restart the listener as root
Start the listener as root.
At the operating system prompt, enter tnslsnr with optional command line arguments. The usage is as follows:
tnslsnr [listener_name] [-user user] [-group group]
where:
Table 4-3 tnslsnr Utility Options
Option Description
listener_name
Specify the name of the listener. If omitted, the default name LISTENER will be used.
-user user
Specify the user whose privileges the listener will use when super user (root) privileges are not needed. After performing the privileged operations, the listener will give up root privileges irreversibly.
-group group
Specify the group whose privileges the listener will use when super user (root) group privileges are not needed. After performing the privileged operations, the listener will give up root group privileges irreversibly.
The listener will temporarily switch to the provided user and group immediately after startup. All subsequent operations will be done with the specified user and group privileges, except the system calls necessary to listen on configured endpoints. The listener will revert to super user (root) for a short period of time to listen on reserved addresses, such as TCP ports less than 1024. After the listener starts listening on all of its endpoints configured in listener.ora, it will switch to the specified user and group irreversibly. Therefore, the listener will give up the root privilege that it initially had. In the current release, -user and -group command line arguments only accept user and group identifiers specified in numeric form.
For example, to execute a root listener called mylsnr and have it use privileges of a user identified

Need step by step to get port 48705 open for Panasonic Bluray

Similar Messages

Maybe you are looking for