Need to block rv110w access to router from wan

Is there any way to block access to the router logon page from the wan? By simply going to the router's external WAN IP, the cisco logon screen shows up? I really think this not that safe and want to block it from showing up. I have looked at all the settings and don't seem to be able to find something that will keep that from happening.
Thanks
M

Hello Michael,
You can disable remote management via Firewall --> Basic Settings. In the basis settings page there should be an option to enable remote managment. Make sure that option is unchecked.
Hope this helps.
-john

Similar Messages

What is the easiest way to access the router from an iPad? I have no problems accessing it from my laptop. Even though I am entering the address in the left address box, not the Google search box, it wants to do either a search, or add www beginning of

What is the easiest way to access the router from an iPad? I have no problems accessing it from my laptop. Even though I am entering the address in the left address box, not the Google search box, it wants to do either a search, or add www to the beginning of the IP address.
I usually can eventually access the router, but it is way to much trouble. However, I use my iPad hundreds of times more often than my laptop.

Are you typing http:// in front of the IP address of the router? e.g. http://192.168.0.1
Sometimes, and with some routers it doesn't seem to like it if you miss off the http://

Trying to access my 851w from outside my lan, but can access inside fine

Hi,
I purchased a 851w to use as my home router and to learn more about the cisco IOS. I have been spending some time studying for CCENT/CCNA and so far I have enjoyed learning as I go. However, I am having problems accessing this router from a remote location via ssh. I can access it just fine from my lan, but not outside it from another location. Currently, I am not using this router for internet access or anything else other than learning about the IOS, and it is connected to a basic dlink wireless router dir-615. I have port forwarding setup on the dlink that any traffic coming in on port 22 is directed to the 851w at 192.168.0.150. I also have the 851w connected with a crossover cable to a switch that is connected to the dlink router.
Like I said, I can connect just fine from my lan, but can't connect from outside. I have tried a few different things but nothing works. I also use Teraterm to connect, but have tried Putty too. I also use ddns to access it, but I have also tried the wan ip address of the dlink with no luck.
Could someone please take a look at my very basic running config and explain what I might need to do different?
Thanks in advance.
Sean

Hi and thanks a bunch for your quick response.
No, I can't ping anything other than my main router which I have setup as the gateway so why is that? For example,
ip default-gateway 192.168.0.1
Wouldn't it automatically send anything it doesn't know about to the 192.168.0.0/24 router?
I have one of the switch ports, Fast Ethernet 0, connected to another switch connected to the dlink router. I have tried different ports but it didn't change anything. I don't have anything connected to the wan port of the 851w. I was trying to simulate remote access of a switch on an internal network. My next step would be to make the 851w my default router and then try to access it from the outside, but I wanted to succeed this way first.
optimus#show ip int br
Interface IP-Address OK? Method Status Protocol
Dot11Radio0 unassigned YES unset administratively down down
FastEthernet0 unassigned YES unset up up
FastEthernet1 unassigned YES unset down down
FastEthernet2 unassigned YES unset down down
FastEthernet3 unassigned YES unset up down
FastEthernet4 unassigned YES unset administratively down down
Vlan1 192.168.0.150 YES manual up up
Yes, my internal pc is on the 192.168.0.0/24 subnet.
Best Regards,
Sean

Wireless ACL - Block internal access

I need to block all access from the guest wireless to our internal network.
The following is the ACL I've come up with so far for the guest SSID. I thought seq 1 and 2 would work - 1 allow clients to communicate with DHCP and 2 block access to all internal IP addresses. I had to add seq 3 for clients to access the internet as a workaround for now. Unfortunately because of seq 3 clients can also access everything else on our internal network.. I believe the descriptions are correct. Not 100% sure. It's what I want them to do anyway.
Our DHCP Windows server hands our guest wireless clients an IP address and sets their DNS to the DNS of our ISP not our internal DNS server.
The guest VLAN DHCP range is 10.55.12.50-10.55.13.254.
Our internal network is any IP in the 10.55 range.
Our controller is a Cisco 4402.
How do I accomplish this?
ACL: GuestWiFi
Seq
Action
Source IP/Mask
Destination IP/Mask
Protocol
Source Port
Dest Port
DSCP
Direction
NoH
Desc
1
Permit
10.55.12.0 / 255.255.255.255
10.55.1.1 / 255.255.255.255
UDP
DHCP Client
DHCP Server
Any
Inbound
0
DHCP Server. Allow clients to respond to DHCP requests.
2
Deny
10.55.12.0 / 255.255.255.0
10.55.0.0 / 255.255.0.0
0
Any
Any
Any
Any
0
Block access to internal network - all 10.55 addresses
3
Permit
0.0.0.0 / 0.0.0.0
0.0.0.0 / 0.0.0.0
Any
Any
Any
Any
Any
0

Not a problem. The order is very important.
First allow access to all of your network. This ends up being last in the sequence. Then start denying access. For our network I permitted to all and then added vlans to deny. At the very beginning of the sequence is where I allowed access to specific devices/services on vlans that are blocked. Here is an example. There could be a better way of doing this. If there is please chime in.
ACL: GuestWiFi
Seq
Action
Source IP/Mask
Destination IP/Mask
Protocol
Source Port
Dest Port
DSCP
Direction
NoH
Desc
1
Permit
0.0.0.0 / 0.0.0.0
10.55.1.117 / 255.255.255.255
UDP
DHCP Client
DHCP Server
Any
Inbound
0
Allow printer
2
Deny
10.55.12.0 / 255.255.252.0
10.55.8.0 / 255.255.252.0
Any
Any
Any
Any
Any
0
Internal Wireless Vlan
3
Deny
10.55.12.0 / 255.255.252.0
10.55.5.0 / 255.255.252.0
Any
Any
Any
Any
Any
0
Management Vlan
4
Permit
0.0.0.0 / 0.0.0.0
0.0.0.0 / 0.0.0.0
Any
Any
Any
Any
Any
0
Everything

BAPI name to access employee data from systems like CSS, ISP GTP etc

Hi All,
Could you please suggest which BAPIs we need to use to access employee data from systems like CSS, ISP GTP etc
Regards,
Poonam
Moderator message: Welcome to SCN!
Moderator message: please do more research before asking, show what you have done yourself when asking.
[Rules of engagement|http://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement]
[Asking Good Questions in the Forums to get Good Answers|/people/rob.burbank/blog/2010/05/12/asking-good-questions-in-the-forums-to-get-good-answers]
Edited by: Thomas Zloch on May 20, 2011 2:09 PM

Hi All,
Could you please suggest which BAPIs we need to use to access employee data from systems like CSS, ISP GTP etc
Regards,
Poonam
Moderator message: Welcome to SCN!
Moderator message: please do more research before asking, show what you have done yourself when asking.
[Rules of engagement|http://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement]
[Asking Good Questions in the Forums to get Good Answers|/people/rob.burbank/blog/2010/05/12/asking-good-questions-in-the-forums-to-get-good-answers]
Edited by: Thomas Zloch on May 20, 2011 2:09 PM

How do I block a website so it cannot access my computer? I am having problems with ad sites downloading ads that are so large they lag my computer so badly that I can't do anything. I need to block those sites from downloading their ads.

mookie1.com is downloading ads when I access websites. The downloads are LOOOOOOOOOONG and freeze my computer. I need to block the downloads.

mookie1.com is downloading ads when I access websites. The downloads are LOOOOOOOOOONG and freeze my computer. I need to block the downloads.

Access a webserver on a computer that has a router from the internet.

Hi I am new to routers and wanted to get some information on how to access a webserver that is on a computer which is connected to a router. I am very confused about port forwarding. Basically lets say that the webserver is on a computer with the ip of 192.168.1.100. I want to know how to use the internet IP (either one that is auto or one that is fixed) to connect to the webserver outside of the local network from a computer on internet. I was able to do it before the router was installed. Can someone explain this to me or point me into the direction of something that is easy to understand? Thanks, Message Edited by wjriv on 03-26-2008 09:16 PM
Message Edited by wjriv on 03-26-2008 09:16 PM

Still having problems..   I have configured the router to forward ports 80 (web server) to my Linksys router address of 192.168.1.100 (which is the address for the computer that the web server is on).   I also tried DMZ to 192.168.1.100..
I use DynDns to direct my IP address...
I know it works, because I can access the router config from the Internet through port 8080...   But when I try to put in my DynDns or actual IP address (for example: 100.110.10.201)   I enter it as follows:    http://100.110.10.201:80
But I am not able to access the web server from out side of my network.
I have also made my computer with the web server keep the IP address static.
Are there any other things that need to be configured in the router or even in the firewall of the computer?
I have noticed that this has been a major issue in different forums, but I have not been successful with a solution.
My ISP is Bellsouth.net..   I am not sure if they could be blocking anything..
It actually works when I remove the router from the system and just connect it directly.. so that is telling me that there is something else that needs to be configured on the router.
Can anyone help me or direct me to the solution?
This is really frustrating....
Thanks..

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

HT204406 I am having a very difficult time with accessing my music from the cloud. I need to have itunes open on my laptop in order for it to work. And as soon as I close out itunes on my laptop, it gives me a warning that all users will be logged out.

I am having a very difficult time with accessing my music from the cloud. I need to have itunes open on my laptop in order for it to work. And as soon as I close out itunes on my laptop, it gives me a warning that all users will be logged out. Help!!!

Where are iTunes files located?
No, I do not mean just the music. Copying just the media/music files or the media folder creates problems.

The circuit of my macbook is dead yet the hard drive is fine. I need to access a file from the hard drive, how can i do this? is there a cable i can connect to another mac that will let me transfer the file?

The circuit of my macbook is dead yet the hard drive is fine. I need to access a file from the hard drive, how can i do this? The mac turns on the screen freezes as bright blue. Is there a cable i can connect to another mac that will let me transfer the file?

There is another option if the Macbook will start up in Target Disk Mode.
Restart the computer while holding down the T key. If you see the firewire symbol moving around on the screen you can connect this one to another one in TDM. You will need a suitable cable to connect the two Macs.
http://support.apple.com/kb/ht1661
Firewire symbol:

I have an iphone6. I am unsure whether to go from 8.1.3 operating system and switch to ICloud Drive or not? Has anyone done this? Is it awesome? I need to be able to access my resume from phone. I think this will help me achieve this.am i right?

I have an iphone6. I am unsure whether to go from 8.1.3 operating system and switch to ICloud Drive or not? Has anyone done this? Is it awesome? I need to be able to access my resume from phone. I think this will help me achieve this? Am i right? Is there any body out there right now that could help me? I'm thinking about going from 8.1.3 to I guess yosemite? Or is that for Mac computers? I don't understand the language entirely on the help page. Anyone's straight forward and easy stepped advice would be much appreciated. I'm so frustrated and I need a job so badly! Drowning in debt. Any help appreciated!
Thanks,
A

You're a Windows user, correct? If so, read here:
http://support.apple.com/kb/DL1455

I need to erase all Contents and Settings from my i phone 5 but I forgot the restrictions passcode. How can I get it. ( Idon't have access to i tunes). Thanks.

I need to erase all Contents and Settings from my i phone 5 but I forgot the restrictions passcode. How can I get it. ( Idon't have access to i tunes). Thanks.

Not possible. You need access to iTunes.
The passcode will be required to make changes to these settings or to disable Restrictions. Note: If you lose or forget a restriction passcode, you will need to perform a factory restore to remove it.
The above comes from here:
http://support.apple.com/kb/HT4213

HT5085 I have purchased an app from iTunes and now it won't allow me open it? What do I need to do to access this app on my mac?

I have purchased an app from iTunes and now it won't allow me open it? What do I need to do to access this app on my mac?

Nothing. iOS applications can't be run on a computer.
(103423)

My iphone was lost and I need to access my photos from my computer using icloud. How do I do this?

My iphone was either lost of stolen. I am able to access my contacts from icloud, but I don't know how to access my photos. Is this possible? if so, how?

Hi deekswife,
Welcome to the Apple Support Communities!
If you want to view Photo Stream photos on a Windows computer you will first need the iCloud Control Panel installed. Once installed, there will be an iCloud Photos location selected on your computer. Please review the following article as a reference.
iCloud: Set up My Photo Stream
http://support.apple.com/kb/PH13693
On a Windows computer
Install the iCloud Control Panel if it isn’t already installed on your computer.
Open the iCloud Control Panel, then turn on Photos.My Photo Stream is set up by default. To turn it off, click Options, then turn off My Photo Stream.
To change the iCloud Photos location on your computer, click Options. Click Change to choose a folder, then click OK.
Click Apply.
I hope this helps,
-Joe

Access USB Disk from Win XP connected to Router

Hello,
My Airport express is plugged into cable modem router and so is a desktop running Win XP.
Another 2 machines Macbook and Winxp laptop can access AE router, internet and the USB disk connected to AE.
I am having trouble accessing the USB disk from desktop which does not have wifi and is hooked directly to cable modem router. I tried assigning a static IP to Airport Express and that didnt help either.
Any ideas?
hhol

Welcome to the discussions!
You posted in the AirPort Extreme forum, but your post indicates that you have an AirPort Express.
If you have an AirPort Express, this device does not support hard drives at the USB port. Only compatible printers are supported.

Need to block rv110w access to router from wan

Similar Messages

Maybe you are looking for