Need to find information of the size of monitor on my MacPro computer.

My computer is about 5-6 years old, and I lost all papers described it. I found only this information:  
Model Name:          MacBook Pro
  Model Identifier:          MacBookPro3,1
  Processor Name:          Intel Core 2 Duo
  Processor Speed:          2.2 GHz
  Number Of Processors:          1
  Total Number Of Cores:          2
  L2 Cache:          4 MB
  Memory:          2 GB
  Bus Speed:          800 MHz
  Boot ROM Version:          MBP31.0070.B07
  SMC Version (system):          1.16f11
  Serial Number (system):          W874****X91
  Hardware UUID:          00000000-0000-1000-8000-001B63950151
  Sudden Motion Sensor:
  State:          Enabled
I guess that it is 15". I don't know any other sizes except 13"; 15"; 17". Do you know where in my computer I can find this information?
<Edited by Host>

System Profiler will show the resolution of your display under "Graphics/Displays".
It should be 1440 x 900 for a 15" MacBook Pro.
Is this what you are asking or do you want the diagonal dimension of the display?

Similar Messages

  • ERROR:  cannot find information from the FND_FORM_FUNCTIONS table

    Hi,
    I am in CU2, i have created my project, set the right responsibility in Project property panel of my Jdeveveoper.
    When i run the first page all is ok, but if i click on a h-grid link , i receive the following error:
    "Your system has not been properly set up. The system cannot find information from the FND_FORM_FUNCTIONS table which is needed for this process. Please consult your System Administrator for further assistance."
    This happens only if i launch the custom from jdeveloper. On the Applications, the custom works fine.
    Any idea about the error?
    Thanks in advance,
    Carlo

    Please check the calling logic which is written to invoke the custom form from the existing form.

  • Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site

    Have an existing ex2010 sp3 organization.
    Could not run ex2013cu1 setup from my newly built 2012 server, getting the error in the subject line.  I used the command line to run the AD preparation steps successfully from my 2012 DC/GC, then tried to run setup again from the new 2012 server and
    still get the same error.  The error itself in the log is pretty useless:
    [05/07/2013 01:19:13.0137] [0] **********************************************
    [05/07/2013 01:19:13.0137] [0] Starting Microsoft Exchange Server 2013 Cumulative Update 1 Setup
    [05/07/2013 01:19:13.0137] [0] **********************************************
    [05/07/2013 01:19:13.0152] [0] Local time zone: (UTC-08:00) Pacific Time (US & Canada).
    [05/07/2013 01:19:13.0152] [0] Operating system version: Microsoft Windows NT 6.2.9200.0.
    [05/07/2013 01:19:13.0152] [0] Setup version: 15.0.620.29.
    [05/07/2013 01:19:13.0152] [0] Logged on user: DOMAIN\ADMINISTRATOR.
    [05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0168] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='sourcedir', Value='\\h1\f$\junk\installers\server\Exchange\2013cu1'.
    [05/07/2013 01:19:13.0215] [0] Command Line Parameter Name='mode', Value='Install'.
    [05/07/2013 01:19:13.0215] [0] RuntimeAssembly was started with the following command: '/sourcedir:\\SERVER\f$\junk\installers\server\Exchange\2013cu1 /mode:Install'.
    [05/07/2013 01:19:13.0215] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:19:13.0793] [0] Finished loading screen CheckForUpdatesPage.
    [05/07/2013 01:19:38.0762] [0] Finished loading screen UpdatesDownloadsPage.
    [05/07/2013 01:19:40.0496] [0] Starting file's copying...
    [05/07/2013 01:19:40.0496] [0] Setup copy files from '\\SERVER\f$\junk\installers\server\Exchange\2013cu1\Setup\ServerRoles\Common' to 'C:\Windows\Temp\ExchangeSetup'
    [05/07/2013 01:19:40.0700] [0] Finished loading screen CopyFilesPage.
    [05/07/2013 01:19:40.0840] [0] Disk space required: 1292445007 bytes.
    [05/07/2013 01:19:40.0840] [0] Disk space available: 23767240704 bytes.
    [05/07/2013 01:19:59.0762] [0] File's copying finished.
    [05/07/2013 01:19:59.0965] [0] Finished loading screen InitializingSetupPage.
    [05/07/2013 01:20:02.0934] [0] Setup is choosing the domain controller to use
    [05/07/2013 01:20:09.0325] [0] Setup is choosing a local domain controller...
    [05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
    [05/07/2013 01:20:11.0809] [0] Setup will use the domain controller ''.
    [05/07/2013 01:20:11.0809] [0] Setup will use the global catalog ''.
    [05/07/2013 01:20:11.0825] [0] Exchange configuration container for the organization is 'CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
    [05/07/2013 01:20:11.0919] [0] Exchange organization container for the organization is 'CN=DOMAIN,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain,DC=local'.
    [05/07/2013 01:20:11.0966] [0] Setup will search for an Exchange Server object for the local machine with name 'WEX1'.
    [05/07/2013 01:20:12.0028] [0] No Exchange Server with identity 'WEX1' was found.
    [05/07/2013 01:20:12.0044] [0] The following roles have been unpacked:
    [05/07/2013 01:20:12.0044] [0] The following datacenter roles are unpacked:
    [05/07/2013 01:20:12.0044] [0] The following roles are installed:
    [05/07/2013 01:20:12.0059] [0] The local server does not have any Exchange files installed.
    [05/07/2013 01:20:12.0075] [0] Server Name=WEX1
    [05/07/2013 01:20:12.0137] [0] Setup will use the path '\\SERVER\f$\junk\installers\server\Exchange\2013cu1' for installing Exchange.
    [05/07/2013 01:20:12.0137] [0] The installation mode is set to: 'Install'.
    [05/07/2013 01:20:27.0591] [0] An Exchange organization with name 'DOMAIN' was found in this forest.
    [05/07/2013 01:20:27.0591] [0] Active Directory Initialization status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Schema Update Required Status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Organization Configuration Update Required Status : 'False'.
    [05/07/2013 01:20:27.0591] [0] Domain Configuration Update Required Status : 'False'.
    [05/07/2013 01:20:27.0841] [0] Applying default role selection state
    [05/07/2013 01:20:27.0872] [0] Setup is determining what organization-level operations to perform.
    [05/07/2013 01:20:27.0872] [0] Because the value was specified, setup is setting the argument OrganizationName to the value DOMAIN.
    [05/07/2013 01:20:27.0872] [0] Setup will run from path 'C:\Windows\Temp\ExchangeSetup'.
    [05/07/2013 01:20:27.0888] [0] InstallModeDataHandler has 0 DataHandlers
    [05/07/2013 01:20:27.0888] [0] RootDataHandler has 1 DataHandlers
    [05/07/2013 01:20:27.0903] [0] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.  See
    the Exchange setup log for more information on this error.
    [05/07/2013 01:20:27.0935] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:21:04.0154] [0] The registry key, HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\ExchangeServer\V15\Setup, wasn't found.
    [05/07/2013 01:21:04.0154] [0] End of Setup
    [05/07/2013 01:21:04.0154] [0] **********************************************

    Hi,
    The cause is clearly described in the log:
    [05/07/2013 01:20:11.0794] [0] [ERROR] Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. 
    See the Exchange setup log for more information on this error.
    [05/07/2013 01:20:11.0794] [0] [ERROR] Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency.
    I'd suggest you check NIC settings and AD configuration.
    Hope it is helpful.
    Fiona Liao
    TechNet Community Support

  • If we open a transaction i need to find what are the tables used

    hi gurus
    can anyone suggest me
    if we open a transaction  liek va01
    i need to find what are the tables used
    what are the fields used in that transaction
    i need a list .
    thanks&regards
    kals.

    Hi
    you can find all those details in transaction variant,
    go with SHD0 ( numerical 0) and then enter your transaction code and enter transaction variant name and then select that
    Select the program SAPMV45A and go CHANGE WITH PROCESSING (F6),
    there you can find the list of fields and field names.
    reward points if usful.
    thanks and regards,
    muralidhar

  • Where can I find information on the purchase date of my iCloud plan?

    Could anyone help me locate where to  find information on the purchase date of my iCloud plan?
    Thank you in advance,

    Here are some tips on dealing with multiple contacts.
    http://support.apple.com/kb/TS4147?viewlocale=en_US&locale=en_US
    In particular, look at the section entitled Resolving duplicate Contacts using Contacts or Address Book.
    Matt

  • Where could i find information about the state of my request to change my ipod nano 1st gen?

    my ipod 1st gen is part of the program of replacement, but i dont know where i can find information about the state of my request. some ideas?   

    You can enter the Serial Number and Repair ID on this page to get a stsus update:
    https://selfsolve.apple.com/repairstatus/main.do;jsessionid=0phLTksW2mwLbyQVF3Qs zFtCQMH2Jv5xkMxvMlD6RsKVLhpJjpjj!846893301
    Hope that helps!

  • Someone stole my Ipod and i Need to find it but the person who stole it isn't using wifi how can i find it

    Someone stole my Ipod and i Need to find it but the person who stole it isn't using wifi how can i find it

    Until it's turned on and connected to the Internet you cannot find it.
    What To Do If Your iDevice Is Lost Or Stolen
    If you activated Find My Phone before it was lost or stolen, you can track it only if Wi-Fi is enabled on the device. What you cannot do is track your device using a serial number or other identifying number. You cannot expect Apple or anyone else to find your device for you. You cannot recover your loss unless you insure your device for such loss. It is not covered by your warranty.
    If your iPhone, iPod, iPod Touch, or iPad is lost or stolen what do you do? There are things you should have done in advance - before you lost it or it was stolen - and some things to do after the fact. Here are some suggestions:
    This link, Re: Help! I misplaced / lost my iPhone 5 today morning in delta Chelsea hotel downtown an I am not able to track it. Please help!, has some good advice regarding your options when your iDevice is lost or stolen.
      1. Reporting a lost or stolen Apple product
      2. Find my lost iPod Touch
      3. AT&T. Sprint, and Verizon can block stolen phones/tablets
      4. What-To-Do-When-Iphone-Is-Stolen
      5. What to do if your iOS device is lost or stolen
      6. 6 Ways to Track and Recover Your Lost/Stolen iPhone
      7. Find My iPhone
      8. Report Stolen iPad | Stolen Lost Found Online
    It pays to be proactive by following the advice on using Find My Phone before you lose your device:
      1. Find My iPhone
      2. Setup your iDevice on iCloud
      3. OS X Lion/Mountain Lion- About Find My Mac
      4. How To Set Up Free Find Your iPhone (Even on Unsupported Devices)

  • I have photostream turned on on my iPhone, and my macbook and phone are synced. However, I can't find any of the photos from my phone on my computer. Help!

    I have photostream turned on on my iPhone, and my macbook and phone are synced. However, I can't find any of the photos from my phone on my computer. Help!

    Have you looked in iPhoto on your Mac under the "Photo Stream" area shown on the left sidebar?

  • Inform about the Size of the files stored in DMS as warning message

    hi DMS Gurus,
    We have a critical requirement of informing the users about the size of the file getting stored in SAP DMS, we need to inform the users the size of the file getting stored as this has a implication on flowing the documents in to remote Mobile device, and the concern is, any document above 2 MB would take much longer time or may not flow at all,
    so we need this information available in DIR, so the user can have a choice to choose the file before sending it to Mobile device,
    can i know if this file size is logged in SAP System anywhere?
    Any suggestion is welcome
    Thanks and regards,
    Kumar

    Hi Kumar,
    normally the file size could be found in table DMS_PHF_CD1. You should be able to get the correct entry by using the LOIO- or PHIO-ID which can be obtained by report DMS_KPRO_READ. Other useful tables are DMS_PH_CD1, DMS_PHIO2FILES and DMS_DOC2LOIO.
    Best regards,
    Christoph

  • I need a script to reduce the size of the Fra which has used 34 gb in space

    I need an rman script to reduce the size of the Fra:
    SQL> select * from v$flash_recovery_area_usage;
    FILE_TYPE PERCENT_SPACE_USED PERCENT_SPACE_RECLAIMABLE NUMBER_OF_FILES
    CONTROL FILE 0 0 0
    REDO LOG 0 0 0
    ARCHIVED LOG 0 0 0
    BACKUP PIECE 0 0 0
    IMAGE COPY 0 0 0
    FLASHBACK LOG 69.99 19.33 2357
    FOREIGN ARCHIVED LOG 0 0 0
    7 rows selected.
    SQL> SELECT
    2 ROUND((A.SPACE_LIMIT / 1024 / 1024 / 1024), 2) AS FLASH_IN_GB,
    3 ROUND((A.SPACE_USED / 1024 / 1024 / 1024), 2) AS FLASH_USED_IN_GB,
    4 ROUND((A.SPACE_RECLAIMABLE / 1024 / 1024 / 1024), 2) AS FLASH_RECLAIMABLE_GB,
    5 SUM(B.PERCENT_SPACE_USED) AS PERCENT_OF_SPACE_USED FROM
    6 V$RECOVERY_FILE_DEST A,
    7 V$FLASH_RECOVERY_AREA_USAGE B
    8 GROUP BY
    9 SPACE_LIMIT,
    10 SPACE_USED ,
    11 SPACE_RECLAIMABLE ;
    FLASH_IN_GB FLASH_USED_IN_GB FLASH_RECLAIMABLE_GB PERCENT_OF_SPACE_USED
    50 34.99 11.14 69.99

    In /gateprd/ARCHIVE/*.arc
    This is the script to remove the archives after it has been backup by the netbackup policy named Archive. This policy removes the archives that have been backed up.
    /home/oracle/dba/scripts> more rmovarch.sh
    #!/bin/ksh
    # compress /gateprd/ARCHIVE/*.arc
    find /gateprd/ARCHIVE/*.arc -type f ! -exec echo {} > /home/oracl
    e/dba/lists/ARCHIVElist \;
    if test $(cat /home/oracle/dba/lists/ARCHIVElist|wc -l) -gt 0
    then
    echo "Hay archives. Se corre script de borrar"
    /home/oracle/dba/scripts/ARCHIVE_BACKUP.sh ARCHIVE
    else
    echo "No archives!!"
    fi

  • Need pin out information for the TB2644 J connectors

    The online documentation for the TB-2644 interface block used with the 2532 Switch does not show the pinouts for the output connectors J1-J4. I need this information so that I can run ribbon cables to an external user interface.

    Hello KLP,
    Welcome to the NI Discussion Forums!  If you search for 2644 on ni.com, you will get a link to the TB-2644 product page.  This page contains some useful information on the terminal block.  In the resources tab open the manuals link and you will see the 8 manuals associated with this device.  The NI TB-2644 Installation Instructions has the information you are looking for.  You can see the pinouts for the column and row connections on page 3 of the manual as well as some ribbon cables that will fit these connectors.  The 2644 is used for matrix expansion in the Dual 8x32 and 2-wire 8x32 matrix modes for the card.  The NI-Switches Help (installed when you install the switch driver) shows this information.  You can find this help file in Windows in the Start menu under Programs -> National Instruments - > NI-Switch -> Documentation -> NI Switches Help (the documentation folder also has the specifications sheets for each switch and terminal block supported by your version of NI-Switch).  If you go to the Devices section in the help file you will find the NI PXI-2532 listed.  There is section on the 2-Wire 8×32 Matrix Topology and the 1-Wire Dual 8×32 Matrix Topology.  If you check these you can see how each column and row is assigned to one of the connectors on the terminal block.  The terminal block installation guide will show you the ordering of the pins.  Hope this helps!
    Regards,
    Browning G
    FlexRIO R&D

  • Need help finding information about a photo taken on my iphone, date, gps

    I took a photo a few months ago and I still have the photo on my phone, I need to find out the date, time and GPS coords of the photo, I had an app a long while back that would do this and I am pretty sure its free but I have no idea what it was called and its long since been deleted. I dont care what app I have to buy I really need this info and the phone itself will only show the location on a map but not give me the rest (as far as I can tell).
    Thanks!

    I'm not sure which iPhone app provides for this, but a photo viewing software on your computer should.
    Import the photo from your iPhone's Camera Roll with your computer and use a photo viewing software on your computer that reveals this data for the photo.

  • HT6195 Where can I find out what the size of update files are, before I download them?

    My provider charges based on data usage (which is very costly here!), so I need to be able to locate file sizes prior to downloading them in order to stay within my budget.   The last (single file) update cost me $54.00, so yes, it matters!

    only option is to use a download manage and stop the download if the size is unwanted
    http://mac.appstorm.net/general/three-download-managers-for-mac-and-do-you-need- them/
    more
    https://www.google.dk/search?q=download+manager+mac&oq=download+manager+&aqs=chr ome.2.69i57j0l5.3907j0j7&sourceid=chrome&es_sm=91&ie=UTF-8

  • Images in LR and finder 10% of the size they should be?!

    Hi guys,
    I just imported every photo I've ever taken into LR (21,000+ images, took about 4 days!). I had previously imported them into an Aperture trial, but Aperture was stupidly, impossibly slow, so now I imported them into LR. When I view them both in Finder and the "Develop" window, they're about 10% of the size they should be. When I zoom to even 25%, they're all pixellated.
    Of course, I"m freaked out that all of my images were somehow reduced 90%, though I have no idea how this could have possibly happened. Anyone know what the deal is?
    Alec

    More detail:
    It seems LR imported 10,269 images as thumbnails (approximately half of my 21,366 photo library) to a folder 2000>December 31, with the files dates renamed (as I specified) as "Date-Number" (ex: 20060710-14857). These files are what shows up when I click "Reveal in Finder" from LR.
    However, when I look in the LR-created folder 2006>July 10, the actual files are still there and intact. Why doesn't LR show these files when I click "Reveal in Finder"? Why a huge folder of thumbnails the size of half my library?
    Did Aperture make thumbnails and then LR imported them?
    I don't get it - can any explain to me what's going on here?
    Alec

  • I find information about the performance of the ATG scenario engine.

    Hi all,
    It is a big point that I can release a business user directly by using a scenario of the ATG.
    It is the strongest that I can use the information that tracked a site for the element of the scenario.
    I almost collect the tracking information of the site for the site business in Japan.
    However, it is the present conditions to use only the analysis of the count level.
    I want to reclaim the world of totally new digital marketing in Japan.
    It is necessary to release many scenarios to realize 'one to one marketing '.
    However, such as the performance there is a question.
    At first do you know the example that you use a scenario positively, and realizes an offer and recommend?
    In addition, do you know which part of the sizing is important when you come true?
    Regards,
    hirofumi

    ATG scenario engine is one of the feature that ATG provides for a personalised user experience, but the major limitation of scenario is it is event driven, you need to design your ecommerce application in such a way that you have to identify the possible events anddecide on appropriate actions. This will help in very few scenarios but a larger ecommerce application concerns it is very limited.
    --At first do you know the example that you use a scenario positively, and realizes an offer and recommend?
    This will be very difficult to achieve using a scenario, you can display some basic promotions to the customer but not a real recommendation. First to remember that scenario is not a recommendation engine.
    Also this will not useful in case of anonymous customer since tracking anonymous customer behaviour is extremely difficult without a proper recommendation engine. either you have to custom build or go with a third party recommendation engine.
    Cheers
    R

Maybe you are looking for