Need to monitor 7201 router without package for Ciscoworks

Hello,
I'm a few months away from upgrading our Ciscoworks platform from LMS 2.6 to 3.1. However, I need to monitor a 7201 router and will not be able to to install the package for that system. I 'm getting snmp traps and get request, but the system is shown as unkown because I don't have the package installed. My support has run out until I get the 3.1 LMS software approved for purchase. Until then is it possible to monitor the 7201 router, I am receiving snmp message but Ciscowork doesn't seem to relate them correctly without the package being installed. I want to monitor the system for reachablity and sent a e-mail message out if it fails that test.
Jeff

Perhaps something like eWatch would work for you. Leopard will also offer some tracking and monitoring abilities as part of the upgraded Parental Controls.

Similar Messages

  • Need help on which router to buy for my BB 8320

    Now i know 8320 is dated but at this point i am not planning to change anytime soon .
    So I have a router which is kinda old, it didnt really occur to me since it worked. When i got my bb 8320 i was in a hotel and i could connect through their wireless without any hassle. I could surf, use youtube, name it.
    When i got home i couldnt do anything, i spent countless nights trying to figure out waht was wrong then i realized its my router. If only BB said somethign it wont support old routers then i wouldve saved myself hours of self-loathing.
    Anyways I also have gone to my friends house, and i could connect to her linksys router without any hassle. i was the one who set her router up and we bought it this year. i didnt do anything special, configuration-wise or w/e.
    So NOW i am just going to buy a new router. I really need help!!!!
    I was wondering if this one is good:
    W311R Wireless-N Broadband Router
    W311R integrates the wireless AP, router, four-port switch and firewall in one, and increases over 4 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 2.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate. It is dedicated to SOHOs and students’ dormitory. In addition, URL and MAC address filtering can take it easy for parents and network administrator to manage network life, and QoS bandwidth control over specific computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet.
    Overview:
    * Includes router, wireless access point, four-port switch and firewall in one
    * Provides up to 150Mbps uploading and downloading speed
    * Supports two WPS (Wi-Fi Protected Setup) encryption methods: PBC and PIN
    * Compliant to IEEE802.11n, IEEE802.11g, IEEE802.11b, IEEE802.3 and IEEE802.3u standards
    * Supports far-distance transmission, 100 meters indoor, 400 meters outdoor (depends on the environments around)
    * Supports 64/128-bit WEP encryption, WPA and the latest WPA2 encryption security authentication
    * Supports RTS/CTS protocol and data partitioning function
    * Provides one 10/100Mbps Auto-Negotiation Ethernet WAN ports for WAN connection
    * Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports for LAN connections
    * Supports xDSL/Cable MODEM, static and dynamic IP in community networking
    * Supports remote/local Web management
    * Supports WMM to better smooth your voice and video
    * Supports SSID stealth mode and access control based over MAC address (up to 30 entries)
    * Supports Auto MDI/MDIX
    * Supports wireless Roaming technology and ensures high-efficient wireless connections
    * Supports auto negotiation/manual mode for 802.11b/802.11g/802.11n
    * Supports UPnP and DDNS
    * Supports Firefox 1.0, IE5.5 or above
    * Supports SNTP
    * Supports virtual server, DMZ host
    * Built-in firewall for hacker’s attack prevention
    * Supports DHCP server/client
    * Supports auto wireless channel selection
    * Supports the control over LAN access to Internet
    * Provides syslog to record the status of the router
    * Supports WDS wireless network extension
    * Supports QoS function
    Input Voltage Range
    AC 110~240V
    Output Voltage Range
    9V~1000mA
    Consumption
    20dbm
    Operating Temperature
    0? ~ 40?
    Storage Temperature
    -40? ~ 70?
    Operating Humidity
    10% ~ 90% RH non-condensing
    Storage Humidity
    5% ~ 90% RH non-condensing
    Antenna
    One Non-detachable external antenna (5dBi)
    Frequency Range
    2.4GHz-2.5GHz
    EVM
    -30dB
    Sensitivity
    54M:-74dBm@10% PER; 11M:-85dBm@8% PER; 6M:-88dBm@10% PER; 1M:-90dBm@8% PER
    Outdoor
    400m
    Indoor
    100m
    WLAN?LAN
    93Mbps
    WLAN?WLAN
    93Mbps
    Frequency Range
    2.4GHz
    Gain
    5dBi
    Nominal Impedance
    50
    Polarization
    Linear; Vertical
    Maximum Power
    1W
    * Vertical Beamwidth 360º

    Flip UltraHD.
    Shoots mp4 H264 format files. Fits in a shirt pocket and records 2 hrs worth of material to an internal card. Charges from your USB port as you download. If you are just trimming clips, you can use QT Pro without conversion. If you need to edit, convert to ProRes 720p30. Works like a dream.
    Just make sure you have it solidly placed when you pull the trigger as there is no image stabilization.
    Oh, and it is only $199 US.
    x

  • Advice needed - multiple monitors, what software is right for this?

    I have an Intel Mac Pro (10.6) at work with 4 monitors, with screen sharing activated. I have an Intel mac Pro (10.6) at home with 2 monitors. I'd like to be able to do screen sharing, and the clients I've tested so far are driving me nuts - I can't figure out how to see all the monitors (one at a time if need be). What's the right solution - will ARD allow me to see the other monitors conveniently, or do I need Mobile Me, or ?? Advice would be greatly appreciated.
    thanks,
    Mike

    Hi Mike
    If the remote computer has multiple screens attached, ARD gives you the option to show all as one large screen or individual 'sessions' for each screen.
    ARD 3 features here-
    http://www.apple.com/remotedesktop/upgrade.html

  • Need simple copy UI command (without selection) for KM items

    In a list of documents in KM I want to be able to do a simple copy operation without having to choose the target folder to put the copied item in. I simply want to duplicate an item in the folder it resides.
    I cannot find other relevant copy commands in the flex UI than the ones that are under the category 'UI Commands with Selection'.
    Anyone?
    Henning

    Hi,
    Well, I don't think there is one but you can implement one pretty easily.
    If you need help with that let me know.
    Best regards,
    Avishai Zamir

  • I need help choosing the right adobe package for my health records

    can you please advise who i can meet and discuss the needs of my business in regard to making health records and keep them safe. the cloud ideas sounds good but i have a legal responsibility for privacy of my clients to ensure files are protected.
    can you advise who or how i can preferrably meet with someone who has solid knowledge in adobe products to advise me  please

    fredfromhuntington beach wrote:
    Thanks again for the reply (from some time ago!). I hope to get a reply from you based on my following simplification of how I intend to use my backup. No...I haven't moved forward on my decision of what/how to conduct my backups!
    1) I prefer to use a single backup device for each computer
    2) I would like to be able to create DVDs of movies, and (if time becomes an issue) do a backup of the DVD
    How would you modify your suggestion(s) to me based on these changes?
    Thanks!
    OK, were I starting from scratch, I would go with the docking station from the OWC link.  (I think the price has actually come down $20 since my original post!  Man, I love pricing on electronics stuff!)  You can easily move it from one computer to another and bare drives are cheaper to purchase and easier to store.   If you want a full-time device for each computer, I would probably still recommend the docking station, especially with the price falling like it is.
    IMHO, the best storage solution for bare drives is this box from Wiebe Tech, which is sturdy ESD plastic and nearly as compact as the 3.5 inch drive.  My backups rotate through a safe deposit box that can hold a bunch of them, though I usually have only two offsite at any one time.
    For DVD backups, I have in the past imaged DVDs using Disk Utility, which works out nicely, especially when I need to burn more copies.  And you can just mount the image of a video DVD and DVD player comes up and you can watch from the hard drive.

  • Delivery without reference for stock transfer within the same plant 311

    Dear all,
    I need to create a delivery without reference for stock transfer within the same plant, movement 311,  i.e. just from 1 storage location to another storage location.
    I tried to use VL01NO with delivery type UL.
    Now my question is how can I assign a receiving plant for a customer?
    I can't do the MIGO or MB1B document because I need the delivery document (packing list, forms, Texts,...).
    It's possible this option???
    Thank you very much.

    Hi,
    What is the item category you are assigning while doing VL01NO?  Check the schedule line category for that item category assignment.  That Schedule line category has an option for one step GI.  There you can assign 311 or create a separate item category and schedule line category and in that SC assign 311. 
    Thanks
    Krish.

  • Number of structures in package for ABAP proxy

    Hey guys,
    do we need 4 levels of structures in package for a simple ABAP proxy to file scenario,isn't there any inbuilt package which can be used(cant we jst use $TMP as it is )?
    thanx
    ahmad

    hi,
    they (those structures) look like the messages interface that you created in the Integration repository
    have a look at the data type (on which message interface is based on)
    and this weblog
    /people/ravikumar.allampallam/blog/2005/03/14/abap-proxies-in-xiclient-proxy
    the structure will have all the fields from the
    data type
    is it clearer now ?
    Regards,
    michal
    <a href="/people/michal.krawczyk2/blog/2005/06/28/xipi-faq-frequently-asked-questions"><b>XI / PI FAQ - Frequently Asked Questions</b></a>

  • My 10 yr old wants to text from his iPod touch. We have 1 family Apple ID. How can I monitor his texts without receiving all of his friends messages? Do I need a separate Apple ID or can I link a new email address to the same Apple ID?

    My 10 yr old wants to text from his iPod touch. We have 1 family Apple ID. How can I monitor his texts without receiving all of his friends messages? Do I need a separate Apple ID or can I link a new email address to the same Apple ID?

    Just an email address
    MacMost Now 653: Setting Up Multiple iOS Devices For Messages and FaceTime

  • Hi there, can anyone tell me how to make make Garageband ignore HDMI as an audio output-device on a 2013 Mac Mini? Now it keeps on prompting me: Do you want want to use the HDMI device (monitor without audio) for audio output? Thanks in advance, Grtz T.

    Hi there,
    Can anyone tell me how to make make Garageband ignore HDMI as an audio output-device on a 2013 Mac mini i7 using an Apogee jam as an input for bass and a Behringer USB DAC with RCA audio output? Now it keeps on prompting me: Do you want want to use the HDMI device (monitor without audio) for audio output? I'm also suffering massive audio lag issues with the Apogee jam after waking the mini from sleepmode, wich pretty much renders it useless.
    Thanks in advance,
    Grtz T.

    I think the easiest way to do this is to have the EyeTV app running in one user account and sent via HDMI to the TV, and use a separate user account for Screen Sharing. Both logins can be active at the same time and with Lion you can connect via screen sharing to which ever login you need.
    With regards to the Mac video resolution changing, when it is not the current input on your AV receiver. This is 'normal', if the Mac sees no signal it drops down the a lower level. What you need is to buy a HDMI Detective Plus which tricks the Mac in to always seeing a signal and hence it will not drop down the resolution. See http://www.gefen.com/kvm/dproduct.jsp?prod_id=8005
    The Mac mini does have an IR receiver. This can be used with the EyeTV app, iTunes, and similar. Yes I believe EyeTV would run for prolonged periods quite happily, it is has been around for a long time and had most of the rough edges polished off. However one issue you will have to deal with is that it does not automatically update its program guide data. For this you might have to write or modify an AppleScript. Elgato support or their user forums will be a lot of help.
    You can set EyeTV to convert recordings to an iTunes (Apple TV) compatible format and then delete them from EyeTV.
    The HDMI Detective should solve your handshaking problems.

  • Cisco view for Cisco 7201 router

    Hi ,
    We have LMS 3.0.1 and we are not able to get cisco view for Cisco 7201 router.
    Any help would be appricated.
    thanks,
    Samir

    Make sure you have version 22.0 of the Rtr7000 CiscoView package loaded.  You can update your CiscoView packages under Common Services > Software Center > Device Update.

  • Help needed: making a psptoolchain package for arch

    Hi....
    I'm very new to archlinux (now using it for 3 weeks), but I really like it
    Now I tried to make a archlinux package for the psptoolchain (PSP's are so nice )
    I already got a working package for the psp-gcc and the psp-binutils (wrote my own PKGBUILD's) which came with the psptoolchain.
    But now I got stuck with psp-newlib and pspsdk.
    At the moment I'm building all the packages separately, but later I'll try to make one package for the whole psptoolchain....
    So here comes my problem with psp-newlib and pspsdk...
    psp-gcc -march=i686 -O2 -pipe -G0 -Wall -I../../src/base -I../../src/kernel -c sceAtrac3plus.S
    sceAtrac3plus.S:0: error: bad value (i686) for -march
    Assembler messages:
    Error: Bad value (i686) for -march
    make[3]: *** [sceAtrac3plus.o] Error 1
    make[3]: Leaving directory `/mnt/data/archlinux/packages/psptoolchain/pspsdk/src/pspsdk/src/atrac3'
    make[2]: *** [all-recursive] Error 1
    make[2]: Leaving directory `/mnt/data/archlinux/packages/psptoolchain/pspsdk/src/pspsdk/src'
    make[1]: *** [all-recursive] Error 1
    make[1]: Leaving directory `/mnt/data/archlinux/packages/psptoolchain/pspsdk/src/pspsdk'
    make: *** [all] Error 2
    ==> ERROR: Build Failed. Aborting...
    And here comes my PKGBUILD for psp-newlib:
    # Contributor: [email protected]
    pkgname=newlib
    pkgver=1.13.0
    pkgrel=1
    pkgdesc="GCC for psp-devel"
    url="http://ps2dev.org/psp/Tools/Toolchain/"
    depends=()
    makedepends=()
    source=(ftp://sources.redhat.com/pub/newlib/$pkgname-$pkgver.tar.gz)
    md5sums=('3d07cc367a22b78c44227456b0d3b7dc')
    build() {
    export PSPDEV="/usr/local/pspdev"
    export PATH="$PATH:$PSPDEV/bin"
    cp $startdir/newlib-1.13.0.patch /$startdir/src/$pkgname-$pkgver
    cd $startdir/src/$pkgname-$pkgver
    cat newlib-1.13.0.patch | patch -p1
    cd /$startdir/src/$pkgname-$pkgver
    BUILDDIR="/tmp/pspdev" PSPDEV="/usr/local/pspdev" ./configure --prefix=/usr/local/pspdev --target=psp
    make || return 1
    make DESTDIR=$startdir/pkg install
    I know, using newlib as pkgname is bad, but later I'll change it to psp-newlib and I'll replace the $pkgname's with newlib (I hope this idea isn't too bad)
    One last thing: psp-binutils and psp-gcc are installed in "/usr/local/pspdev"
    I hope you can help me
    thanks, and have a nice day
    XazZ

    After a long break I decided to work on the PKGBUILD again.
    Now I got two PKGBUILD's: one for the psptoolchain and one for pspsdk (pspsdk gets updated very often, so I decided to create an extra PKGBUILD).
    I'm not sure if my PKGBUILD's fit the PKGBUILD-standard
    First thing before I post my PKGBUILD's: I'm not finished with adding all required fields (as license and so on)!
    Here comes the one for psptoolchain:
    pkgname=psptoolchain
    pkgver=2211
    pkgrel=1
    pkgdesc="A collection of tools to create executables for the Sony PSP"
    url="http://ps2dev.org/psp/Tools/Toolchain/"
    depends=('subversion' 'texinfo')
    makedepends=()
    license=('GPL')
    source=(ftp://ftp.gnu.org/pub/gnu/binutils/binutils-2.16.1.tar.bz2 ftp://ftp.gnu.org/pub/gnu/gcc/gcc-4.0.2/gcc-4.0.2.tar.bz2 ftp://sources.redhat.com/pub/newlib/newlib-1.15.0.tar.gz)
    md5sums=('6a9d529efb285071dad10e1f3d2b2967'
    'a659b8388cac9db2b13e056e574ceeb0'
    '4020004b1b7a56ca4cf7f6d35b40a4cb')
    sha1sums=('5c80fd5657da47efc16a63fdd93ef7395319fbbf'
    'f1b714c6398393d8f7f4ad5be933b462a95b075d'
    'f6860b36e48fb831a30bab491230bbc7ce2669a2')
    arch=('i686')
    _svntrunk=svn://svn.pspdev.org/psp/trunk/psptoolchain
    _svnmod=psptoolchain
    _svntrunk1=svn://svn.pspdev.org/psp/trunk/pspsdk
    _svnmod1=pspsdk
    build() {
    cd $startdir/src
    svn co $_svntrunk $_svnmod
    cd psptoolchain
    cp binutils-2.16.1.patch $startdir/src/binutils-2.16.1/
    cp gcc-4.0.2.patch $startdir/src/gcc-4.0.2/
    cp newlib-1.15.0.patch $startdir/src/newlib-1.15.0
    export PSPDEV="$startdir/pkg/usr/local/pspdev"
    export PATH="$PATH:$PSPDEV/bin"
    msg "patching and building binutils..."
    cd $startdir/src/binutils-2.16.1
    cat binutils-2.16.1.patch | patch -p1
    ./configure --prefix=/usr/local/pspdev --target=psp --enable-install-libbfd
    make clean || return 1
    make || return 1
    make DESTDIR=$startdir/pkg install
    msg "building and patching binutils finished"
    msg ""
    msg "patching and building gcc..."
    cd $startdir/src/gcc-4.0.2
    cat gcc-4.0.2.patch | patch -p1
    mkdir objdir
    cd $startdir/src/gcc-4.0.2/objdir
    ../configure --prefix=$startdir/pkg/usr/local/pspdev --target=psp --enable-languages="c" --with-newlib --without-headers
    make || return 1
    make DESTDIR=/ install
    msg "building and patching gcc finished"
    msg ""
    msg "building pspsdk-headers - we'll only need them temporary"
    cd $startdir/src/
    svn co $_svntrunk1 $_svnmod1
    cd $_svnmod1/
    ./bootstrap
    ./configure --prefix=/usr/local/pspdev -with-pspdev=/usr/local/pspdev
    make clean || return 1
    make DESTDIR=$startdir/pkg install-data
    msg "building pspsdk-headers finished"
    msg ""
    msg "patching and building newlib-psp"
    cd $startdir/src/newlib-1.15.0
    cat newlib-1.15.0.patch | patch -p1
    ./configure --prefix=$startdir/pkg/usr/local/pspdev --target=psp
    make || return 1
    make DESTDIR=/ install
    msg "building newlib-psp finished"
    msg ""
    msg "building gcc-c++"
    cd $startdir/src/gcc-4.0.2
    mkdir build-psp-c++
    cd $startdir/src/gcc-4.0.2/build-psp-c++
    ../configure --prefix=$startdir/pkg/usr/local/pspdev --target=psp --enable-languages="c,c++" --with-newlib --enable-cxx-flags="-G0"
    make clean || return 1
    make CFLAGS_FOR_TARGET="-G0"
    make || return 1
    make DESTDIR=/ install
    msg "building gcc-c++ finished"
    msg ""
    msg "removing unnecessary code"
    cd $startdir/pkg/usr/local/pspdev/psp
    rm -rf sdk
    msg "Now you need to build and install pspsdk!"
    And here the one for pspsdk:
    pkgname=pspsdk
    pkgver=2209
    pkgrel=1
    pkgdesc="A collection of Open Source tools and libraries written for the Sony Playstation Portable (PSP)."
    url="http://ps2dev.org/psp/Tools/Toolchain/"
    depends=('psptoolchain')
    makedepends=()
    arch=('i686')
    license="custom"
    _svntrunk=svn://svn.pspdev.org/psp/trunk/pspsdk
    _svnmod=pspsdk
    build() {
    export PSPDEV="/usr/local/pspdev"
    export PATH="$PATH:$PSPDEV/bin"
    cd $startdir/src
    svn co $_svntrunk $_svnmod
    cd $_svnmod/
    ./bootstrap
    ./configure --prefix=/usr/local/pspdev -with-pspdev=/usr/local/pspdev
    make clean || return 1
    make DESTDIR=$startdir/pkg install-data
    make clean || return 1
    ./configure --prefix=$startdir/pkg/usr/local/pspdev -with-pspdev=/usr/local/pspdev
    make || return 1
    make DESTDIR=$startdir/pkg install
    Some explanation: I've used this one very often: --prefix=$startdir/pkg/usr/local/pspdev
    Explanation: When I wanted to create only one PKGBUILD for the psptoolchain, some dependences were in $startdir/pkg. If you take  --prefix=/usr/local/pspdev he won't get some depencies (mostly header files), which means I had to create single PKGBUILD's for every part of the psptoolchain (that would be 6 single parts).
    Those --prefix-changes don't stop my psp environment from working! (tested it myself - I comiled almos all sample apps which were included in the pspsdk - and all compiled well)
    I hope we can find a better solution than mine.
    Thanks in advance
    XazZ

  • HT1379 The USB ports on my 30" Cinema are not working.  The monitor has not been used for a year or so, and the computer is a Mac Book Pro, 1012 model running OS Mavericks.  I need to move the computer between two locations, and the other monitor is a 27"

    The USB ports on my 30" Cinema HD display appear to not work.  The monitor has not been used for almost a year, when I upgraded to a new Mac Book Pro and the 27" retina display.  Now I need to move the computer back and forth between two locations using the two displays.  The need for operating USB ports is essential.  Any ideas.  The display appears entirely normal.  Am running OS X 10.9.

    Disregard, problem solved.

  • I bought a song on itunes a while ago and I couldn't back up my ipod because I needed more storage. Once my ipod was updated, ALL of my memory was deleted (since it wasn't backed up) and I couldn't get my song back without paying for it again. Is there a

    I bought a song on itunes a while ago and I couldn’t back up my ipod because I needed more storage. Once my ipod was updated, ALL of my memory was deleted (since it wasn’t backed up) and I couldn't get my song back without paying for it again. Is there a way to retrieve it without paying for the second time?

    Just follow these instructions:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • Macbook hard drive crashed, i lost windows for mac, bought a disc when i got the mac, no longer have the disc, need my apps, don't wanna pay for it again.  know how to get it quick without having to give my mac to the genius bar at apple store overnight

    macbook hard drive crashed, i lost windows for mac, bought a disc when i got the mac, no longer have the disc, need my apps, don't wanna pay for it again.  know how to get it quick without having to give my mac to the genius bar at apple store overnight?

    What is it you need - Windows installer disc or something else?  Your question is unclear.  Could you be more specific?

  • I need a monitor power supply for HP2711X. Where can I buy one?

    I need a monitor power supply for HP2711X. Where can I buy one?
    This question was solved.
    View Solution.

    Because the XP597A3 (actually any of these product numbers; XP597AA, XP597A3, XP597AS) is a HP 2011x 20" LCD/LED widescreen monitor. The OP was looking for an A/C adapter power supply for the HP 2711x 27" LCD/LED widescreen monitor, which is product # XP600AA or XP600A3. The adapter power supply I linked to, is the correct part for the 2711x monitor.... that is why not those other parts.
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Maybe you are looking for