Need to Reboot Modem Daily

My plan is 7.1mbps, and I can regularly achieve a little over 6. However, my speed typically runs just below 3 until I reboot the modem. At that time, it immediately achieves around 6mbps down. If I do not reboot, and check it a few hours or maybe a day later, it is back to the lower speed. Reboot, and the speed recovers. If anyone can provide any suggestions they will certainly be appreciated.

If the stats as read at the modem level are o/k, there are three additional signal stats which can't be read by the modem. They can only be read from their end by them polling the CMTS (Cable Modem Termination System) at the local headend facility.
They are the 'Upstream Receive Power Level', the 'uSNR' (upstream Signal To Noise Ratio), and the "ICFR" (In Channel Frequency Response). These are as equally important in diagnosing connectivity issues as are the modem's stats.
You can call in and ask what these figures are. The Upstream Receive Power Level should fall within the range of -2dB to +2dB with 0dB being in the middle and perfect.
The Upstream SNR should be least 31dB, and the higher it is the better.
The ICFR should be no higher than 2 dB.
You could have an intermittent noise ingress issue in only the upstream channel(s) / return path only somewhere.
They will be able to see whether or not everything is in the green zone and also see a history plot for the modem.

Similar Messages

Need to Reboot SB6141 Daily

I've been with Comcast for about 2 months now and my own personal Arris SB6141 has been the only modem I've used. I'm hooking the ethernet out from the modem to my Netgear N900 wireless router. Since day 1, I've had to reboot the modem almost daily. Don't know why. I spoke with an Arris rep about this and they pointed me to some information which suggests that my modem is not the problem, rather it is something upstream. I reviewed that info and all of my values fall with in the recommended ranges. The latest error that I've seen in the modem's log not related to me rebooting the modem (power off/on) is : SYNC Timing Synchronization failure - Loss of Sync . The modem reboots just fine and I'm back on line with great speed...no complaints there. On a couple of occassions, all of the modem's lights are off except the one for power. That has only happened a couple of times. Most of the other times the link light stops flashing or the internet connection light goes out. Reboots always fix it. Not sure how to post my modem stats on here.

If the stats as read at the modem level are o/k, there are three additional signal stats which can't be read by the modem. They can only be read from their end by them polling the CMTS (Cable Modem Termination System) at the local headend facility.
They are the 'Upstream Receive Power Level', the 'uSNR' (upstream Signal To Noise Ratio), and the "ICFR" (In Channel Frequency Response). These are as equally important in diagnosing connectivity issues as are the modem's stats.
You can call in and ask what these figures are. The Upstream Receive Power Level should fall within the range of -2dB to +2dB with 0dB being in the middle and perfect.
The Upstream SNR should be least 31dB, and the higher it is the better.
The ICFR should be no higher than 2 dB.
You could have an intermittent noise ingress issue in only the upstream channel(s) / return path only somewhere.
They will be able to see whether or not everything is in the green zone and also see a history plot for the modem.

WRT350N v1.03.7 always need to reboot daily.

Now I don't know how to make my router work more stable. I guess that my WRT350N cannot free up memory for the ports has opened it after unused them. After working around several hours, internet slowing down and it need to reboot. My PC usually run vuze (azureus). I hope that new firmware can fix this issue ASAP.

If you have to reboot the router daily you must upgrade the router's firmware...
Download the Firmware from here
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Painfully slow or need to reboot

Ever since I installed Yosemite on my MacBook Pro, my computer is either constantly so slow or needs to be rebooted. I NEVER needed to find out before how to do a Ctrl-Alt-Del for a Mac until I loaded Yosemite. Any suggestions on how to make my computer run the way it use to?

Problem description:
MacBook Pro is extremely slow or freezes to the point of needing to reboot
EtreCheck version: 2.0.6 (91)
Report generated October 21, 2014 at 9:59:11 PM EDT
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10 (14A389) - Uptime: 5 days 0:59:29
Disk Information: ℹ️
TOSHIBA MK3265GSXF disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / [Startup]: 318.84 GB (119.89 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 319.21 GB Online
MATSHITADVD-R   UJ-8A8
USB Information: ℹ️
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.philips.iokit.DLconnect (85) Support
Problem System Launch Agents: ℹ️
[failed] com.apple.AirPlayUIAgent.plist
[failed] com.apple.BezelUI.plist
[failed] com.apple.CallHistoryPluginHelper.plist
[failed] com.apple.CallHistorySyncHelper.plist
[failed] com.apple.cmfsyncagent.plist
[failed] com.apple.coreservices.appleid.authentication.plist
[failed] com.apple.coreservices.uiagent.plist
[failed] com.apple.EscrowSecurityAlert.plist
[failed] com.apple.gamed.plist
[failed] com.apple.iconservices.iconservicesagent.plist
[failed] com.apple.pbs.plist
[failed] com.apple.pluginkit.pkd.plist
[failed] com.apple.printtool.agent.plist
[failed] com.apple.recentsd.plist
[failed] com.apple.sbd.plist
[failed] com.apple.scopedbookmarkagent.xpc.plist
[failed] com.apple.secd.plist
[failed] com.apple.security.cloudkeychainproxy.plist
[failed] com.apple.spindump_agent.plist
[failed] com.apple.warmd_agent.plist
Problem System Launch Daemons: ℹ️
[failed] com.apple.AssetCacheLocatorService.plist
[failed] com.apple.awdd.plist
[failed] com.apple.cache_delete.plist
[failed] com.apple.corestorage.corestoragehelperd.plist
[failed] com.apple.coresymbolicationd.plist
[failed] com.apple.ctkd.plist
[failed] com.apple.diagnosticd.plist
[failed] com.apple.icloud.findmydeviced.plist
[failed] com.apple.iconservices.iconservicesagent.plist
[failed] com.apple.iconservices.iconservicesd.plist
[failed] com.apple.ifdreader.plist
[failed] com.apple.Kerberos.digest-service.plist
[failed] com.apple.MobileFileIntegrity.plist
[failed] com.apple.nehelper.plist
[failed] com.apple.periodic-daily.plist
[failed] com.apple.periodic-weekly.plist
[failed] com.apple.sandboxd.plist
[failed] com.apple.softwareupdate_download_service.plist
[failed] com.apple.spindump.plist
[failed] com.apple.sysmond.plist
[failed] com.apple.tccd.system.plist
[failed] com.apple.wdhelper.plist
[failed] com.apple.xpc.smd.plist
Launch Agents: ℹ️
[running] com.newwellnesssolutions.DLconnectMonitor.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
User Launch Agents: ℹ️
[failed] com.facebook.videochat.[redacted].plist Support
[loaded] com.google.keystone.agent.plist Support
User Login Items: ℹ️
iTunesHelper UNKNOWNHidden (missing value)
Microsoft Messenger Application (/Applications/Microsoft Office 2008/Microsoft Messenger.app)
Dropbox Application (/Applications/Dropbox.app)
TimehopSync Application (/Applications/TimehopSync.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 Support
Default Browser: Version: 600 - SDK 10.10
Flash Player: Version: 15.0.0.152 - SDK 10.6 Mismatch! Adobe recommends 15.0.0.189
LogMeIn: Version: 1.0.730 Support
CouponPrinter-FireFox_v2: Version: Version 1.1.7 - SDK 10.5 Support
QuickTime Plugin: Version: 7.7.3
LogMeInSafari32: Version: 1.0.730 Support
OfficeLiveBrowserPlugin: Version: 12.3.6 Support
LogMeInSafari64: Version: 1.0.730 Support
Silverlight: Version: 5.1.30317.0 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 7 Update 67 Check version
Safari Extensions: ℹ️
Pin It Button
Keeper - Password and Data Vault
3rd Party Preference Panes: ℹ️
Flash Player Support
Java Support
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
      7% WindowServer
      6% coreaudiod
      3% com.apple.iCloudHelper
      3% syncdefaultsd
      3% launchd
Top Processes by Memory: ℹ️
60 MB Mail
43 MB com.apple.WebKit.Plugin.64
39 MB WindowServer
39 MB Safari
30 MB mds
Virtual Memory Information: ℹ️
25 MB Free RAM
995 MB Active RAM
983 MB Inactive RAM
1.19 GB Wired RAM
70.76 GB Page-ins
2.47 GB Page-outs

Stratosphere garbled calls, need to reboot

I have a Samsung Stratopshere, almost daily I am needing to reboot my phone. I will be on a call, all the sudden the caller will hear crackling and screeching. If I call them back they instantly hear the screeching/crackling. In order to resolve this I have to reboot, this has been going on for quite some time now...getting quite frustrating!

yadavs wrote:
i have tried resets multiple times
Besides the multiple resets, have you tried a restore? That is the next step in the user troubleshooting. If you have done a restore, did you do both from backup and as a new phone?
If you have done all of these, plus what you have done with AT&T, the next step is Apple. If you do not want to travel to the Apple Store, you can call AppleCare and ship the phone to Apple, however you would be without a phone until it is returned. At least if you go to the Apple store, you walk out with a phone, either the one you came in with, or a replacement. You can make your appointment on line at http://www.apple.com/retail/geniusbar That way you walk in and are taken care of when you appointment comes. If you go without an appointment, you have to wait for the first available opening.

I Need To Hear Modem Sounds Because I Sometimes Travel To Places You Have Never Heard Of.

I Need To Hear Modem Sounds Because I Sometimes Travel To Places You Have Never Heard Of.
Hi!
I have an EliteBook 8740w with Windows 7. I NEED to hear my modem sounds! HELP!
Thanking you in advance,
Ira

Niels approach to get the BootCamp Assistant back is recommended because usually the correct way to remove your Windows partition is to use the BootCamp Assistant again which should give you the option to remove the made Windows partition and revert back to one OSX volume.
After that's done a reboot of your Mac might be advisable.
Only if that's not working (whatever the reason) :
1) boot your Mac from your OSX install DVD
2) choose your language and then 'ignore' (cancel) the installation
3) from the Top Menu (Utilities) start Disk Utility (DU)
4) in DU click on your harddisk (not any partition) in the left pane (the first item listed)
5) in the right pane use the 'Partition'-Tab
6) click to highlight on the ex-Windows partition you want to delete
7) click on the small '-' Button at the bottom
That should delete your former Windows partition
After that's done successfully
8) Drag the partition separator line until it encompasses the entire drive and then select apply.
9) Quit Disk Utility
10) reboot your Mac from your harddisk.
Since you are 'fumbling' with your OSX partition you should consider having/making a backup of it before trying the a.m. procedure. Just in case.
Stefan

I Beta tested 4.0 RC1 and now can not upgrade to 4.0. Error message is need to reboot to complete prior instalation. Have removed all previous versions of Firefox, rebooted and still same error message.

I Beta tested up to and including 4.0 RC1 without major problems. However I can not now upgrade to 4.0. Same error message time and again, "need to reboot to complete prior upgrade instalation". I rebooted several times, then tried first removing all previous versions of Firefox using both MS Add/Remove and then iolo System Mechanic, then again downloading 4.0. Even after rebooting same error message. I can not therefore install/use Firefox.

Do a clean (re-)install:
* Download a fresh Firefox copy and save the file to the desktop.
* Firefox 4.0: http://www.mozilla.com/firefox/all.html
* Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
* Don't remove personal data if you uninstall the current version.
* It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
Your bookmarks and other profile data are stored elsewhere (not in the Firefox program folder) and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.

My Macbook pro has the message on a black screen need the reboot disc then press any key to continue. Any Ideas, because I have no discs.

My Macbook pro has the message on a black screen need the reboot disc then press any key to continue. Any Ideas, because I have no discs.I am running Lion OS

Was this a dark gray screen that appeared with the message to restart the computer in five different languages? If so that's a kernel panic. It would help if you can post the panic log: Mac OS X- How to log a kernel panic. Also visit The XLab FAQs and read the FAQ on diagnosing kernel panics.

IPAD MINI RETINA SCREEN VERSION IOS 7.1.2 can't success download apps , need to reboot every times only can download apps. Is iOS problem or hardware issue.? Local agent switch sale and tech support can't fix my problem.

I Purchase iPad mini retina screen on July 7 2014 at Malaysia local apple sale agent switch store somehow now my iPad did restore to latest iOS 7.1.2, before that and after also facing 1new issue is my iPad mini cant success download apps and error message show can't download at this time, either retry or click done. My internet is good condition no line down, I reboot my iPad only can download but sometime can't need to reboot twice only can download. Very sad local sale and tech support can't help to solve my problem...

Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, tap Settings > General > Reset > Reset All Settings
If that doesn't help, tap Settings > General > Reset > Reset Network Settings
You will have to re enter your Wi-Fi password.
No data is lost due to a reset.
If nothing above helped, try here > iOS: Troubleshooting Wi-Fi networks and connections

HP Envy m6, Updated for Windows 8.1, hard drive needs to reboot

Hey,
I've just updated my software to get the new Windows 8.1. On completing my updates, I recieved a message saying my hard drive has changed and that I need to reboot it. How do I do this? Do I risk losing my files? HELP
HpEnvym6beats

Hello hpenvym6beats. Thank you for posting on the HP Forums. I understand the computer provided a message, indicating the hard drive has changed. It shouldn't become a huge issue, as it does occur sometimes, after completing updates. Just turn off the computer and turn it back on. Your files should not be lost, after completing this task.
Please respond if you have any other questions or concerns.
Mario
I worked on behalf of HP.

Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.

Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.
The first one, my private home email, works fine. With the other 3, I get the message "Cannot get mail: The connection to the server failed"
All were working fine before the 8.3 upgrade. I did try the old trick of making one minor change on the account and resaving, but that did not change anything. I even deleted my work account and re-entered it from scratch, but again, sadly, no luck. For the time being, I am successfully getting the email via IMAP, but this ***** compared to exchange. Anyone have any idea what is happening or if a fix is in the works?

Well, the one set up on exchange 2k3 is now working fine, although no changes were made on either the iPhone or the exchange side, so that's fun, but it still is throwing errors when connecting to the other 2 exchange accounts. The common elements are that both non-functioning exchange accounts are google apps for business accounts. So is one of the ones that's working, by the way. The settings on both accounts are the same as the one that's working, and both worked fine before the 8.3 upgrade. I have no issue accessing both of these accounts on my ipad which is currently on 8.2.x. If it's not the iphone OS at fault, I'm at a loss as to what it could be.

I downloaded Firefox 4 Beta and everytime I tried to open up the browser, I get a message stating I need to reboot the computer in order to complete the upgrade; I've rebooted the computer at least 4 times.

I downloaded Firefox 4 Beta and everytime I tried to open up the browser, I get a message stating I need to reboot the computer in order to complete the upgrade; I've rebooted the computer at least 4 times. I even tried to download a previous version of Firefox and I am still getting the same message that I need to reboot the computer in order to complete the previous upgrade.

I have a very similar problem myself. Error 42408. And my phone isnt being recognized. I have restored my phone with no luck. I completely uninstalled itunes and reinstalled and it worked then when I ejected unplugged and plugged it back in it had the same problem over again.. I have no idea what to do?

I need to reboot my HP Elitebook 6930p hard drive but no F11

I need to reboot the hard drive on my HP Elitebook 6930p. I'm using Windows 7. I hit escape upon turning the computer on and then F9 and chose the hard drive reboot option but then after hitting escape again there is no F11 option to take me to System Recovery. The F11 key does nothing and it's not even listed as an option. Does this mean I need to get discs to reboot and if so, does anyone know where I can buy them low price? If not, is there a step here in the reboot process that I'm missing? Any help would be appreciated. Thank you. Paul

Hi:
Yes you can get any version of W7 that the product key on your notebook is good for at the link below.
Use the applicable SP1 Media Refresh ISO file as they are the latest ones.
http://forums.mydigitallife.info/threads/14709-Windows-7-Digital-River-direct-links-Multiple-Languag...
After you download the ISO file make sure you got the whole advertised file size.
Then use this tool to transfer the ISO file to a 4 GB USB flash drive or DVD.
The tool will also make the media bootable.
http://www.microsoftstore.com/store/msusa/html/pbPage.Help_Win7_usbdvd_dwnTool

Do I need a new modem or a router or neither?

I realise this may dovetail with other posts but I need one or two things to be clarified... Just got airport express which I haven't used before. My modem is ADSL with a USB connection so it's no good for connecting to the airport; I presume I need a new modem with ethernet connection (yes? no?) or, as PC users keep telling me (wary of taking any advice from them) I need a modem router. Can anyone help to shed light on this as I don't know enough yet about wireless connection. Thanks

Just to add a bit to Franks post as to why you would choose a modem or router.
The advantage of an Ethernet modem being that no additional configuration is necessary on the Airport Express and all the features such as iChat AV will work without complicated port forwarding etc. But steer Clear of the D-Link DSL-300T as it is currently incompatible with the latest Airport Firmware.
The Advantage of a router is that they typically have multiple Ethernet ports so as well as wireless computers you can connect Ethernet equipped devices at the same time such as computers, networked printers and game consoles. The problem is that you then need to configure the Airport with "Distribute IP Addresses" switched off and you will then typically need to fiddle about with port forwarding in the router to get things like iChat AV to work properly. Also setting up WDS to use a second Airport to repeat the wireless signal becomes more difficult with this configuration as the Apple WDS system expects "Distribute IP addresses" to be switched on.
Mac OS X (10.3.9) I work for ADSL Nation

After a download update 4.0, I cannot launch. Message says I need to reboot to complete a previous update. I rebooted 5 times to no avail. What now?

After a download update 4.0, I cannot launch. Message says I need to reboot to complete a previous update. I rebooted 5 times to no avail.I have tried searching for xpicleanup.dat to no avail as suggested. What now?

I was able to get live chat support to solve the problem in my post. It worked immediately. Here is what I was told to do. I needed to perform a clean installation Hopefully, it will work for you, too.
"To perform a clean installation, first close Firefox completely. (This chat window
must be closed if it's in Firefox) Then, rename "Mozilla Firefox" to "Old Firefox".
(On 32-bit Windows, this is C:\Program Files\. On x64 Windows, this is
"C:\Program Files (x86)". On Mac, Firefox is in /Applications) Finally, re-install
Firefox normally from http://www.firefox.com"
Since I had already downloaded 4.0, I just went to my download file after renaming the file and ran it.

Need to Reboot Modem Daily

Similar Messages

Maybe you are looking for