Need to take MIB File for Call Manager

Hi,
Can anyone help me how to take MIB file for Call Manager. We have a cluster of 6 CUCM servers (1 pub + 5 Sub). we need this MIB file for monitoring purpose. If you need anyother information regarding this please let me know.

Hi
Below MIBs are supported in CUCM.  Refer the link attached for details. Btw which Version are you running ?
•CISCO-CCM-MIB
•CISCO-CCM-CAPABILITY
•CISCO-CDP-MIB
•CISCO-SYSLOG-MIB
http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cucm/managed_services/cisco_mibs.html
Thanks.

Similar Messages

  • Need SNMP MIB files For Cisco SF 300-48 48-Port 10/100 Managed Switch

    Hi All,
    I need SNMP MIB files for Cisco SF 300-48 48-Port 10/100 Managed Switch.
    I have gone through cisco site but not able to get it.
    Can anyone please provide me.I have stuck with this.
    Thanks
    Ram

    Hi Ram, yes the MIB can be used. The switches are essentially the same in many regards (especially on a software level).
    I do not know the OID for bandwidth. If you're looking for a particular OID may be this tool helps you
    http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=dot1dTpPortTable&translate=Translate&submitValue=SUBMIT&submitClicked=true
    -Tom
    Please mark answered for helpful posts

  • 6140 MIB File for SNMP/6140 Monitoring

    Hi,
    i�m looking for a MIB file for 6140 Disk Array. I found only 3510 MIB file, but nothing related to 6140.
    The target of my actual task is setting up monitoring on a 6140 Array from a customer. We are using Big Sister Monitoring Software.
    3510 monitoring was no problem due to the fact that it was easily getting some status infos via Command Line Tool, this has changed since 6140 is using a new kind of management application, which doesn�t seems to give useable output directly (regarding to a colleague) and requires login.
    Any Suggestions e.g. other ways than snmp for monitoring? Status-Sites from the web-frontend?
    Thanks in advance!
    I

    Hi,
    I have the same problem : finding the 6140's mib to identify traps.
    I guess that SUN-SAM-MIB.mib may be the good one, but I'm not sure.
    to get it, I have downloaded StorageTek SAM-FS 4.6 and searched for mibs inside.
    could someone confirm I found the good mib
    thanks
    thomas

  • HT3669 I only have a HP printer and why I need to install a file for all the HP printers drivers 590MB??? if normally the size of my file should be 5MB.  some one could me help to avoid installation of 590MB for my new mountain lion software???

    Hi guys..!!
    I would like to know if someone could help on this:
    I just have a HP printer (HP Designjet 100) and for some reason I need to install a file for all the HP printers drivers in total 590MB to be able to use my printer in my mountain lion???
    If normally the size of my files in the for previous software was more or less 5MB why now i need to install 590?
    Some one could help me how to avoid installation of 590MB for my new mountain lion software???
    Thanks

    If you go to http://support.apple.com/downloads and locate the HP Printer Drivers installer, you will find that it is 473.4 MB (for version 2.11). If you install this, it will install the full set of drivers for every model of HP printer that is supported by the drivers distributed through Apple. The disk space occupied once installed will probably be larger than the download, since the downloaded file is compressed.
    On the other hand, if you have an HP printer connected and you use Software Update (or the Update tab in App Store), that should offer you a much smaller set of HP drivers, which are only applicable to your printer (and possibly a few similar ones). These updates are typically only tens of megabytes rather than hundreds of megabytes.
    If Software Update doesn't offer you any HP drivers then it either thinks you have the latest drivers installed already, or the printer model is not supported by the drivers available from Apple.
    This article lists all of the printer models for which Apple distributes the driver:
    http://support.apple.com/kb/HT3669

  • I need to download installation files for my Adobe Acrobat Standard 9.5.5.

    I need to download installation files for my Adobe Acrobat Standard 9.5.5. There are no links to be found for this version on the adobe site..
    I have two licenses for adobe acrobat, but cannot find my software. Any help with a direct link to the standard version would be helpful.
    The professional version does not work with the standard licens.

    if you purchased from adobe, log in to your account and check your order history, https://www.adobe.com/account.html
    if you acquired via dell, https://smartsource.dell.com/
    if you purchased elsewhere, contact the vendor.

  • What flash player to use on iPad 2 that is similar to Adobe Flash Player?  Need this to choose files for upload of assignments to my online university.  I started my profile using my iPad 2 and couldn't choose a picture to upload as well.  Hmm

    What flash player to use on iPad 2 that is similar to Adobe Flash Player?  Need this to choose files for upload of assignments to my online university.  I started my profile for this site using my iPad 2 and couldn't choose a picture to upload as well.  Hmm

    There is no "flash player similar to Adobe Flash Player". Flash is a proprietary Adobe product. There is currently no version of Flash for iOS.

  • Trying to find MIB file for 4506

    Hi,
    I am trying to find the MIB files for a cat 4506, after the CPU utiliazation for MRTG.
    Any help appreciated.
    Chris.

    Hi Chris,
    MIB file for CPU utilization is CISCO-PROCESS-MIB. YOu can use the MIB locator for better results. Hope that helps
    http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&mibName=CISCO-PROCESS-MIB
    CISCO MIB locator : http://tools.cisco.com/ITDIT/MIBS/MainServlet?IMAGE_NAME=4500
    Regards,
    Sathvik K V

  • Phone License for Call Manager express

    Dears ,
    Is the phone license required for Call manager express or the license on the voice gateway enough for operating the phones ?
    Regards,

    Hi Ian,
    I think I may have given you some bad info here. Sorry about that
    Right to Use Feature Licenses
    The following licenses do not Cisco software activation and you can begin using the features upon receipt of the Right to Use Notification
    Feature License Name
    Prerequisites
    License Types
    CME
    IP Base & UC
    Feature (Counted)
    SRST
    IP Base & UC
    Feature (Counted)
    VXML Gateway
    IP Base & UC
    Feature (Counted)
    CUBE
    IP Base & UC
    Feature (Counted)
    Land Mobile Radio
    IP Base & UC
    Feature
    You should be good to go. But a quick note to
    [email protected]
    would be a fair idea.
    Cheers!
    Rob

  • SNMP MIB file for Grid Control

    Looking for the MIB file for traps coming out of Grid Control 10gR2. It looks like they're under enterprises.111.15 in the traps I've seen.

    check in AGENT_HOME/network/doc

  • 7975 firmware for call manager express

    i would like to add 7975 phone to call manager express.
    where do I get the firmware for 7975 for cme?
    i tried from software.cisco.com but it's for call manager only.

    Hi pranavluhar,
     check this link cme-153-3Mv2.rar (in 10.0 option).There is a 7975 version for CUCME.
    Hope this helps.

  • Config Archive for Call Manager

    Hello,
    It give me the attahced error fo r config archive for call manager.

    The supported devices page shows each supported device, and what features are supported:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html

  • CDR FIles in Call Manager version 7.1.5-30000

    Good Morning:
    I have a cluster of servers Cisco Call Manager version 7.1.5.30000; 01 Publisher and 02 subscriber. The publisher server passes CDR files to a call accounting application PC-SYSTEL on another server. At one point the CDR files are no longer spend the Call Manager to the application PC-SYSTEL
    Call manager services are reviewed, the part of CDR Management in Cisco Unified Serviciability right. The only solution is doing a RESTART to PUBLISHER server,  and then again go CDR files to the application PC-SYSTEL
    Please anyone has any solution other than to give a RESTART PUBLISHER server, or is this the only way to restore this service.
    Expect your news.
    Thanks in advance for any ideas.
    Regards.
    Fernando.

    Hi Fernando,
    Please check the following.
    (1) Confirm that the billing server is configured correctly (verify the IP address). From the Cisco Unified Serviceability page, navigate to Tools > CDR Management to view the billing server parameters.
    (2) Check if you can ping the billing server from the Publisher. From the Publisher CLI, you can use the following command:
    utils network ping a.b.c.d
       where a.b.c.d is the IP address of the billing server
    (3) Check if the FTP (or SFTP) service/software running on the billing server.
    (4) Check if the billing server is running out of disk-space.
    (5) Check if the CDR Respository Manager service is running on the Publisher. If not, start the CDR Repository Manager service.
    (6) On the Publisher, check the 'preserve' and 'destinationX' (X can be 1, 2 or 3) directories for CDR flat files. For example: if transfer of CDR files to billing server is broken from Jan 6th, then use the following commands:
    file list activelog /cm/cdr_repository/preserve/20110106
    file list activelog /cm/cdr_repository/destination1/20110106
      (if multiple billing servers are configuration, the location will be similar to above, but the corresponding directories will be named destination2, destination3). This location contains symbolic links to files under preserve. CDR Repository Manager service uses these soft-links to determine what files need to be transfered to billing server.  
    If you don't observe files in either the 'preserve' or the 'destinationX' locations for the specific date, then it means that problem does not reside on the Publisher. Either the CDR records were not generated by the server that handled the call or it could mean that CDR Agent service on that server could not transfer flat files to the Publisher. Was the 'CDR Enabled Flag is enabled in CallManager service' enabled on that particular date ? Is the CDR Agent service running on the node that handled the call ?
    If you observe files in the 'preserve' directory for the specific date, try restarting the CDR Repository Manager service on the Publisher. If the file transfer to the billing server does not commence, then set the trace level for the CDR Repository Manager service to Debug, wait 10 minutes, download CDR Repository Manager logs via RTMT and engage Cisco-TAC for further troubleshooting.
    HTH
    Manish

  • Importing Data from SQL DB or Text File to Call Manager 8.5.1

    Hi Everyone,
    I would like to import from an external DB or text  file, what have you, the Employees Single reach Number to Call Manager.  Please let me know your suggestions.
    Thanks

    I don't see why not. This additional requirement would likely require you go the AXL API route so that you can remove unnecessary manual steps. If you are looking for a "trigger" event, then that would be trickier. You may be able to craft something from audit logs or tomcat logs but I don't know if that would be worth the headache. It would require some additional thought.
    You could do a scheduled sync. You will need to ensure you understand all database dependencies and account for some of the additional end user customizations (like time of day and allow lists). The database schema (data dictionary) for your version is here:
    www.cisco.com/en/US/docs/voice_ip_comm/cucm/datadict/8_5_1/datadictionary_851.pdf
    HTH.
    Regards,
    Bill
    please rate helpful posts

  • Virus scan failed Error on deploying a web application having a jar file for calling the applet on the jsp page

    Hi,
    I have an applet application that i want to deploy on the Oracle cloud.
    So i have created a jar file for the applet application and i am using this jar to call the applet on a jsp page.
    But when i am delpoying my application on the java cloud, its giving me the below error:
    2014-10-28 03:16:41 CDT: Starting action "Virus Scan"
    2014-10-28 03:16:41 CDT: Virus Scan started
    2014-10-28 03:16:49 CDT: ----------------------------------------------------------------------
    2014-10-28 03:16:49 CDT: File Scanned: "Application7.ear".
    2014-10-28 03:16:49 CDT: File Size: "106698122".
    2014-10-28 03:16:49 CDT: File Status: "INFECTED".
    2014-10-28 03:16:49 CDT: ----------------------------------------------------------------------
    2014-10-28 03:16:49 CDT: Virus scan failed.
    2014-10-28 03:16:49 CDT: "Virus Scan" complete: status FAILED
    Can't we deploy any application having applet or swing component's onto the cloud?
    Or do we need to request for any extra permissions for the same?
    Thanks,
    Manoj

    I don't see applets mentioned in the supported features nor in the unsupported features so not sure if they are supported you would likely need to contact the operations team to confirm.
    Jani Rautiainen
    Fusion Applications Developer Relations
    https://blogs.oracle.com/fadevrel/

  • MOH Sources for 2 800 #'s for call manager

    Hey all,
    How would i go about configuring 2 MOH sources for 2 different 800 numbers coming into call manager?
    Im stuck at trying to find the location in call manager where the 800 numbers are configured?
    Where abouts would you be able to see what incoming pri configurations are in call manager or am i looking in the wrong place.
    Bascially, i want to use a different MOH source file for a second 800 number.
    Thank you everyone!

    What you translate is dependent on what the telco is sending you and the value configured for Significant Digits in the gateway configuration. If the telco sends you 10 digits and the Significant Digits field is set to All, then you would translate the entire 800 number.
    For Unity, you configure MOH using the device pool of the Unity ports. You can configure the device pool under System -> Device Pool and assign the device pool to the Unity ports under Feature -> Voicemail -> Cisco Voice Mail Port. So, to have 2 different MOH sources for your 800 numbers, you would have to have 2 device pools assigned to 2 sets of voicemail ports and ensure that the numbers get translated to a hunt pilot that uses the proper ports.
    Brandon

Maybe you are looking for