Need to understand WebAuth using 3850 MA, 5760 MC and 5508 GA

All,
I would appreciate if anyone could provide clarification on my current understanding of Converged Access mobility design for WebAuth and guest access. My setup is as follows:
(WAP)---(MA)---(MC)---(Firewall)---(GA)
Wireless Access Point (WAP) - 3500
Mobility Agent (MA) - Cisco 3850 (running IPServices)
Mobility Controller (MC) - WLC 5760
DMZ Firewall
Guest Anchor (GA) - WLC 5508 (running 7.5.110.0 and new mobility feature enabled)
I have my mobility domain configured with an SPG and the 3850 MAs configured into the domain. All status indicators are up for MC to MA and MC to GA. The WAPs are connected to the 3850 MA and appear on the MA using the command 'show ap summary'. There are also a number of WAPs that associate directly to the 5760 MC.
My configuration on the MC has a guest wireless service using WebAuth, which anchors over to the GA. Clients connecting to the WebAuth service on WAPs associated directly to the 5760 MC receive and IP address from the GA DMZ and are redirected to the GA WLC. This is as expected with the usual centralized wireless model.
My initial thoughts with the Mobility Agents (MA) was that it was a simple case of pointing the 3850s to the MC and the wireless service (WLAN) configurations would automatically appear. Through configuration tests and converged access deployment guides, I now believe this to no longer be the case. Therefore, for MAs to advertise wireless services they have to be individually configured. Am I correct with my thoughts?
This was proved with a Secure 802.1x WLAN on the MA and it was a simple case of replicating the 5760 Secure WLAN on the MA.
For the deployment of WebAuth wireless services on the MA 3850 switches, I have not managed to find a guide that explains how an MA anchors wireless clients to the GA. I have found documents that describe combined MC/MA configurations to GA, but not when the 3850 is just an MA. Is it is case that:
1. MA WebAuth wireless service is configured to anchor to the GA using the command 'mobility anchor <GA IP Address>'. This would require the DMZ firewall to allow mobility tunnels between the MA to GA and MC to GA, or;
2. MA WebAuth wireless service is configured to anchor to the MC using the command 'mobility anchor <MC IP Address>'. This would mean the traffic from the MA for WebAuth is tunneled to MC and then onwards to GA.
I suspect option 1 is the correct method, but would appreciate confirmation.
Also, I have not configured a Mobility Oracle (MO) since I only have one MC and the GA. If it is advisable to do, then would it be best to enable the MO on the MC or GA?
Thanks in advance
Ian

Hi Ian,
It is a long post & many questions
I will try to answer as much as I can.
"I have not configured a Mobility Oracle (MO) since I only have one MC and the GA. If it is advisable to do, then would it be best to enable the MO on the MC or GA?"
No, you don't want MO unless your set-up is extremely large (it is similar to use of BGP route reflector to reduce complexity of having full mesh)
"My initial thoughts with the Mobility Agents (MA) was that it was a simple case of pointing the 3850s to the MC and the wireless service (WLAN) configurations would automatically appear. Through configuration tests and converged access deployment guides, I now believe this to no longer be the case. Therefore, for MAs to advertise wireless services they have to be individually configured. Am I correct with my thoughts?"
Yes, you have to configure your WLAN configuration in MC & MA, it won't automatically propagate to MA.
"For the deployment of WebAuth wireless services on the MA 3850 switches, I have not managed to find a guide that explains how an MA anchors wireless clients to the GA. I have found documents that describe combined MC/MA configurations to GA, but not when the 3850 is just an MA"
I have not configured this, but this is my understanding. You would configure MA WLAN pointing to GA as mobility anchor. Still traffic will transit through MC as it will manage MA & SPG (any thing outside SPG should go through MC)
Here is the some useful reference information I gathered over the timel. (white paper is the one you should read to cover everything)
https://supportforums.cisco.com/discussion/11984726/converged-access-design-information
HTH
Rasika
*** Pls rate all useful responses ****

Similar Messages

I need To Understand the "Type Cast Function"

Dears,
I need To Understand How the "Type Cast Function" Work, and if you can Give me an Example it will be Apperciated
BR
Ahmed

In its simplest explanation Type Cast allows you to reinterpret a series of bytes. The numeric conversion functions convert from one data type to another and essentially do the same thing that Type Cast does, albeit with just numbers. Type Cast allows you to extend this to convert one data type to another, beyond just numbers. Thus, you could convert an array of 2 U8 values into a single U16 number by using Type Cast like this:
or you could reinterpret an array of lots of U8 values into an array of U16 values like this:
How you use it is entirely up to you, but it is an extremely powerful function. What are you trying to do?
Attachments:
Example_VI.png ‏6 KB
Example2_VI.png ‏11 KB

Is Solaris Cluster 4.0 Free?. whether we need any license for using it?

I am able to Download the Solaris Cluster from the Oracle Site. But need to know whether we need any license to use it?

Hello 1577859,
and if you like to get the support updates you need a contract to get access to the Solaris Cluster support publisher.
Hth,
Juergen

What's is the best way to use iPhoto? I need to understand.

What's is the best way to use iPhoto? I need to understand.
I guess the iPhoto is only for people with 5,000 of personal photos.
Or even 200,000, but they can't use this app everyday.
I'm not talk about working as a photographer. They use Aperture.
They may use iPhoto like a family album that you take a look sometimes.
And don't care about putting photos from the camera or from internet everyday.
I have tons of music and I love iTunes 8, works great. So I tried but I can't stand iPhoto anymore.
I have over 173,000 photos. My goal is organize, have total control, crop in Preview and delete them fast as I can.
The iPhoto is too slow. And is not only about performance, more RAM... but the whole concept.
Finder is much better/richer/flexible to organize than iPhoto.
I'm not talking about the photographer workflow.
And I'm not talking about editing and all these great photo features, the search, and all the iLife environment. They are amazing.
When I'm iPhoto, I feel like a prisioner.
I can't open an album/folder/event alone just to take a look, without do lanch the iPhoto app with the all thousand photos together. And it's slow.
I can't use Quick Look there.
So, I'll use Finder for manage/crop/etc. But what's the best way to use iPhoto in my case? Put the best/key ones there to use in iLife/MobileMe? To do a more serious editing? I like the features: keywords/ratings/hidden photos/events... It would be cool this features in Finder.
For example:
iMovie: Manage movies? NO. It's editng only.
iTunes: Manage music/small video/podcast...? OK. Editing the song? OK for tags/convert/artwork/equalizer... For music there's a GarageBand of course.
iPhoto: Manage photos? Yes and No.
I think Finder would kill iPhoto incoporating all the editing features in Preview and the rich manage in Finder.
Jobs said that no one care about iDVD anymore. They care about the web.
Using iMovie to export to MobileMe.
Maybe iPhoto become less important in a near future. With a better Finder+Preview Right?
Sorry for this long text with a short question.
Thanks.

Your post demonstrates exactly why I keep saying that iPhoto is not the application for you.
It would be better an iPhoto organizing photos by words like when iTunes browse his music.
Why on earth would anyone want to organise photos by words? A list mode is entirely pointless in a Photo application. That's like having an old photo album organised with the photos facing inwards so you can read the back of the picture.
Again, this is a characteristic of a File browser. You don't want a Photo organiser, you want a file organiser.
And, in iPhoto, you can search by tags, effortlessly in either the search box or by using a Smart Album.
iPhoto always loads all that events and all the thumbs library to scroll, and I think it's overkill.
So, how is iPhoto to know which ones you want to work with today? Open a library, get the Library.
Would be better a Cover Flow option to browsing in Events.
You've obviously never tried scrubbing along the Event icon.
Imagine iTunes using Cover Flow mode all the time. It won't be too useful.
Many, many people do, including myself on a library of 20k tracks totalling more that 100 gigs, and find it very useful. Same with the Finder.
And if when iTunes Store starts to sell photos?
Why on earth would the iTunes store start to sell photos?
My photos are not junk,
I didn't say there were. Read my post again.
When I said Finder to crop photos I mean Preview. But I feel in Finder. Because what's in Preview? A photo opened with a Preview's menubar and some cocoa APIs like adjustments. Not?
Oh, so you don't count Preview as an application. Fine. It is an application but you don't feel it. As you wish.
My point to you is very simple: Because of the way you want to organise your pics - using lists views and so on - iPhoto is not the application for you. Don't use it. But you keep writing things about the application that are untrue, and I'm aware that other folks search these forums and I don't want them to have inaccurate information about iPhoto.
Regards
TD

I need to understand what parameters will tell me that the E3500 server i'm using is under utilised or optimally or over burdened

I need to understand what parameters will tell me that the E3500 server i'm using is under utilised or optimally or over burdened

I need to understand what parameters will tell me that the E3500 server i'm using is under utilised or optimally or over burdened

I have an Iphone 4 using IOS 4.2.6 and need to upgrade to at least IOS 4.3 or better yet IOS 5. I have never received any update notcies. I understand upgrades are through Itunes but when I go to Itunes downloads there is nothing there.

I have an Iphone 4 using ios 4.2.6 and need to upgrade to at least ios 4.3 or better yet ios 5. I have never received any update notices. I understand upgrades are through Itunes but when I go to Itunes downloads there is nothing there. Help!

Thanks, I tried this and it didn't work. I have a windows xp computer and connected the iphone to it. When I click on the iphone link that comes up under my computer i only get my iphone photos. No other options come up.

Ask the Expert: NGWC (3850/5760): Architecture and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about NGWC (3850/5760): Architecture and Deployment.
Ask questions from Monday, April 13th, 2015 to Friday, April 24th, 2015
This Ask the Expert Session will cover questions spanning NGWC products (3850/5760) on Implementation and Deployment from the Wired and Wireless perspective. This will be more specific to Customer’s and Partners questions covering 3850/5760 configuration, Implementation and deployment.
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Wireless CUWN and NGWC Product line. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC-Written) and CCIE Wireless certification.
Naveen Venkateshaiah is working as a Customer support engineer in High-Touch Technical Services (HTTS) handling and supporting Lan-switching and Data center Products. His areas of expertise include Catalyst 3k,4k , 6500 , Nexus 7k Platform He has over 7 years of industry experience working with large Enterprise and Service Provider networks. He also holds CCNA, CCNP (RS) and CCDP-ARCH,CCIE-R&S Written, AWLANFE, LCSAWLAN Certification.
Find other https://supportforums.cisco.com/expert-corner/events.
**Ratings Encourage Participation! **
Please be sure to rate the Answers to Questions

Hi Dhiyadav,
thank you for your reply it cleared some doubts that were in my mind but i need your more support to guide me a converged access deployment which i am going to deploy within few days.
i have
2x5508 in HA as MC
30x3850 switches, and all will be used as MA(s) with multiple SPGs
2X5508 1:1 as an anchor controller
1xISE 1.3 for guest access
1xCPI for wireless mgmt and monitoring purpose
1xMSE3355 with wips and context aware licenses
200x cisco 3702i WAP
50x WSSI module for monitoring the channels
can you please put a light on the design and guide me that which are the best possible solutions to get this job done very smoothly.
i will also let you know about my proposed design scenario but for sure i need your recommendations as well :)
so,
i will use 2x5508 wlcs in HA as a MC which are AP-Count and HA licensed..
3850 switches will be MA and i ll configure SPGs per floor switches stacks
WAPs will join on these 3850 MAs base on each floor
i would have 2 ssid like employee and guest
i will configure them on each 3850 stack MA along with their SVIs for users access like (empolyee and guest ssid)
here my question is for guest ssid and its vlan... do i configure it here or on anchor controller???
i want ISE to be integrated with wireless for employee 802.1x and for guest web Auth. so, how i will integrate ISE with wireless. i mean weather i will integrate it anchor controller or with each 3850 MA???
between foreign and anchor controller i will use new mobility instead of old EOIP!!!
where shall place ISE in my network, in DMZ or with Core switch?
my target for guest users to do not have access to any corporate network sources ?
MSE:
can i use both wips and context aware on the single MSE box?
if yes, than what is the best practice for configuring them?
are each 3850 MA will be added in MSE?
WSSI module . will be used for monitoring purpose for wips and context aware profiles.
all access point will be worked in local mode for serving users access.
thank you

I need help understanding how the Apple components integrate to create a system across all my devices?

I need help understanding how the Apple components connect to create a whole system across all my devices?
Is there a resource that describes current system and associated functionality?
For example:
Buy A, B, C to achieve "X"
You will need:
an internet provider which supports <specs>
add D to achieve "Y"
You will need:
an internet provider which supports <specs>
add "E" to achieve "Z"
You will need:
an internet provider which supports <specs>
For example, I am looking at the Gen 6 Airport extreme. For intended performance do I need broadband? if so what are the specs, or will basic internet service suffice? Do I need the internet provider's modem or does the Airport extreme replace that? And then I think, if I am doing this, I should also look at Apple TV....What do I need and Why? Then I look at the New Desk top coming out in the fall, and I think well, if I wait and get this, what does this component do for the system, and what becomes redundant? What does this awesome desktop do for my ability to sit and use a new macbook air when I travel or sit on the couch in my PJs?
If there was a place that plainly stated "if you buy the new dektop you can configure a system including only these components and achieve <this result> and by adding <additional components> you will achieve this result.
I have been to the genius store a few times, but I come out of there more confused unless I have SPECIFIC questions or already know what to buy.
A "System Configuration App" would be a really great sales tool--Just saying.

I have no idea what "fully optimized" means.
No Apple device will let you watch broadcast TV. The Apple TV is a good option for watching streaming TV from iTunes, NetFlix and Hulu. If you want to watch from other sources, you may need to look at other devices.
Any Mac computer or iPad will allow you to surf the web.
What business software?
Time Capsule is a good option for back ups.
Update what across all devices?
For accessing documents from all devices, a service like Dropbox is your best bet.
I have no idea what "step as far away from an internet provider as possible" means. If you want Internet access, you need an Internet provider.
Lighting fast speed for what? Processor? The specs are listed for all devices in the Online Store. Internet? We're back to the service provider.
Technology changes. The only way to keep pace with it beyond a couple of years is to buy new stuff.
The bottom line is you need to look at the specs for devices availble and at your budget and decide what best meets your needs. If you are unable to do that on your own, there are lot of technology consultants out there who will, for a fee, look at your exact situation, make recommendations and even handle the purchase and set up. Perhaps that would be the best route for you.
Best of luck.

I need to understand better, what can be done with sync and what cannot

i setup 2 windows boxes + 2 linux boxes to sync and got a mess in less than a day. apparently, i do not understand, what it does/should do, and what not.
As one having done work in distributed environments, namely in database replication scenarios, i understand, there have to be limitations, especially, as all of my 4 boxes are running most of the time.
next, i found, that copying profiles wouldnt have worked either, as the windows boxes (have to) use different add-ons/plugins compared to linux (like fireshot - to give a simple example - needed a replacement on linux). - So just moving profiles doesnt help. But the promise to catch open windows/tabs, history, and so forth doesnt seem to work either. Maybe TabMixPlus is killing the whole mechanism?
I found very detailed documentation on where to click to get it all started, but nothing about the internals nor limitations, thus being very disappointed now to find sync actually NOT working at all.
Furthermore, while setting up the whole thing, every machine had a "sync setting" as to how to use that one machine: initial distribution/sync/receiver only/and so forth. Does this only concern the initial setup? - I wasnt able to see this configuration option ever again to be able to change it after the initial setup had been done.
So i obviously need to understand better... as to me it looks like some real messy replication scenario, with not all backends sharing the same tables. And apparently adding/removing add-ons needs to get replicated manually anyway.
What time delay do i have to expect? When shall i use "Syncronize" manually? And so on...
I mean: I trusted Mozilla solution more than any other one, but it doesnt seem to live up to my expectations.
(sorry: i had to reenter the whole thing after my email address ran out)

Ok then! Thanks for answering! Can you still transfer music over? I can't even get that to work! I have set my nephews up with no problem..obviously not a sec generation... please help again!

Project Server 2013: I am using Project Server Permission Mode and need help with permission assignments?

Hi
Project Server 2013: I am using Project Server Permission Mode and need help with permission assignments?
How can I change Permissions for the individual users to see specific projects or all projects in project center and to see specific quick launch items?
For Example: if i have 4 users, A, B, C and D. what i want is:
User A can see everything and act as a project manager or Admin.
User B can view all projects in project centre but can change the schedule or resource assignment etc.
User C can only act as approver of projects and can view all projects in project centre.
User D can only view specific projects for which permissions are given.
can i have some expert help in sorting and understanding permission modes... as i was playing with project server mode permissions and can't figure out how to apply the above scenario to set of my user.
Thanks in Advance
Cheers
AJ
Ajay Kumar

Hi Ajay,
Please refer to this link for detailed explanations about PS2013 security model.
http://technet.microsoft.com/en-us/library/cc197638(v=office.15).aspx
Actually, it will take a couple of days to explain in detail the security model that is a fundamental and tricky aspect of every PS implementation. But basically, you NEVER set permissions for a single user. You have groups in which your insert users. Groups
define "what users can do". Then you associate groups to a corresponding category. Categories define "what user can see". Thus the association of a group with a category will set "what the user can do on the objects he can see". Then, for more advanced security
level, you can use the RBS that will consist in "branches" in which you'll insert users. Based on those branches, you'll customize categories to fine-tune what user can see (for projects and resources) depending on the RBS branch and level.
I'd advice you to start "playing" in a test environment with the default categories/groups that might probably cover your need.
Concerning your 4 users:
user A : add him to the "administrator" group. Be careful that you're mentionning either project manager or administrator, which are 2 groups/categories with totally different permissions level.
user B : basically can see everything and change everything? it could be in the project manager group, assuming that there are no project visibility restrictions on the category via the RBS.
user C : waht do you mean by "approver"? Workflow approvals? Then it will be the portfolio manager group. Task update or timesheet approval? Then it is another long topic: please refer in the documentation to the "status manager" and "timesheet manager"
concepts. There are not related to the security model. In a few words, the status manager is the owner of the project plan, is defined for each task and approves tasks updates. The timesheet manager is an attribute defined for each resource in its parameters
and approves resource timesheet.
user D : you have to define which permission level must be given to this user. Basically it could be a team member that will see only projects he's in the project team. Note that team member cannot interact with the project plan in another way than submitting
timesheets and/or tasks updates which must be approved.
Once more, those are large and complex subjects that require a deep dive into your business model and tons of tests in a test environment.
Hope this helps.
Guillaume Rouyre - MBA, MCP, MCTS

HT1218 What do I need to do to use the Airplay feature with Jango Radio from my iPhone or Mac?

What do I need to do to use the Airplay feature with Jango Radio from my iPhone or Mac?

Thanks Community! I solved the problem. In fact it was not a problem but lack of understanding. These guys at Apple are way ahead in thir thinking. I will try to explain as short as I can.
In Lion, ihe Prefferences/Display show only two choices: 6-7 steps of resolution and some color tab. No two screens, no two display to overlap, nothing for us to do. "That was the problem"! Everything is automatic.
When I connected the HDMI cable to the Miniport into a T-bolt slot, the TV screen showed the "spiral galaxy" how Zyriab is calling it. In fact he gave me the best clue. That shows the connection is good. But where is the Mac Book image?
You have to drag it to the right out of the Mac Book display area, and "voila!" it will continue on the TV screen. The same with the mouse pointer, push it out ofthe Mac Book display area and you see it on the TV sreen. Good image, you can keep the max resolution, etc. The sound is still on the Book's speakers. I have to figure that out.
Thank everybody, especialy Zyriab, ne was the closest.
High regards to everybody

Partition ERROR - 1023040 - msg from remote site : need to understand

hi,
I currently have a problem with the partitions between two cubes.
Architecture:
      80 countries database (source)
      1 world database (destination)
Process :
- The partitions are created dynamically by maxl scripts :
spool on to $1;
Alter application $2 comment '**_batch_**';
Alter application $4 comment '**_batch_**';
Alter system load application $2;
Alter system load application $4;
Alter application $2 disable startup;
Alter application $4 disable startup;
Alter application $2 disable connects;
Alter application $4 disable connects;
/* Create Transparant Partition between Country cube to Mond cube */
create or replace replicated partition $2.$3
AREA
'"S_R_N",
&curr_month,
&local_currency, "D_EURO",
@IDESCENDANTS("P_Produit"),
@LEVMBRS("M_Marche",1),"M_Marche",
@IDESCENDANTS("B_Marque"),
@IDESCENDANTS("U_Sourcing"),
@REMOVE (@DESCENDANTS("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS("I_Divers"),
@IDESCENDANTS("NA_Nature"),MCX'
to $4.$5
AREA
'"S_R_N",
&curr_month,
"D_DEV", "D_EUR",
@IDESCENDANTS("P_Produit"),
@LEVMBRS("M_MixClient",0),"M_MixClient",
@IDESCENDANTS("B_Marque"),
@IDESCENDANTS("U_Sourcing"),
@REMOVE (@DESCENDANTS("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS("I_Divers"),
@IDESCENDANTS("NA_Nature"),MCX,
&country_name'
mapped globally ('',D_$7, "D_EURO", "M_Marche") to (W_$6,D_DEV, "D_EUR", "M_MixClient")
refresh replicated partition $2.$3 to $4.$5 all data;
drop replicated partition $2.$3 to $4.$5;
Alter application $2 enable startup;
Alter application $4 enable startup;
Alter application $2 enable connects;
Alter application $4 enable connects;
Alter application $2 comment '**_enable_**';
Alter application $4 comment '**_enable_**';
Alter system unload application $2;
Alter system unload application $4;
Spool off;
Logout;
exit;
- Defragmentation cubes, launch replications countries successively one by one to the world cubes sequentially .
the order of the country is not the same from one month to another .
Treatment is initiated each month.
Symptoms :
- Partition fall into error with the following message but not systematically .
message:
MAXL > refresh replicated partition PGC_ESP.Pgc_esp PGC_MOND.Pgc_mond to all data ;
   ERROR - 1023040 - msg from remote site [ [ Wed Nov. 29 10:21:03 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error ( 1023040 ) msg from remote site [ [ Wed Nov. 29 10:21:02 2013] hprx1302 / PGC_ESP / Pgc_esp / PGC_ADMIN / Error (1023040) msg from remote site [ [ Wed Nov. 29 10:21:01 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error ( 1042012 ) Network error [ 32] : Can not Send Data ]]] .
We note that the error occurs in the following cases:
- The errerur happens generally when the average clustering ratio is low. (cube fragmented) for cubes source and / or destination
- When beacuoup replication were done before: in the last 10 to 15 cubic remaining replicate.
- We mistake once on the environment recipe on the first cube with average clustering ratio to 0.96 but the server recipe is much less efficient.
We noticed that when doing a defragmentation cubes source and destination once the error obtained treatment replication was no longer falling into error.
Problem: defragmentation cube world take 10 hours.
We also made the following observation:
OK/INFO - 1051034 - Logging in user [PGC_ADMIN].
OK/INFO - 1051035 - Last login on Friday, November 29, 2013 10:19:46 AM.
OK/INFO - 1053012 - Object [Pgc_esp] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [Pgc_mond] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [54116855] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [39843334] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [54116855] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [39843334] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Target] - Partition definition is not valid: [Cell count mismatch: [1279464568200] area for slice [1] members per dimension [63 1 2 1 6 26 7 245 1 37955 ]].
OK/INFO - 1053012 - Object [25586652] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [11329970] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [25586652] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [11329970] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Source] - Partition definition is not valid: [Cell count mismatch: [47895484140] area for slice [1] members per dimension [63 1 6 7 2173 2 17 1 245 ]].
OK/INFO - 1053013 - Object [Pgc_esp] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [Pgc_mond] unlocked by user [PGC_ADMIN].
OK/INFO - 1051037 - Logging out user [PGC_ADMIN], active for 0 minutes.
OK/INFO - 1241124 - Partition replaced.
Following these findings we need to understand what is happening.
We would like to understand why partitons fall errors?
why we have the message "Partition definition is not valid" in the logs when creating the partition?
Regards,
Oliv.

Hi SreekumarHariharan,
Tx to your anwers, but we are already try all the solution proposes to Essbase FAQ.
a)Increase the values for NETDELAY and NETRETRYCOUNT in essbase.cfg file.Restart the essbase server.
We are changed the two value in the essbase.cfg but nothing to do. The same error appears
b)Make sure that the all source members and target members used in partition are in sync
All member are diferent between source and target but a mapping are defined in the partition (see the partition maxl in my below message.
c)Validate the partition (look at the validation tab, it will give the numbers for each side of the partition ie source area and target area)
You can see the logs of validation partition :
WARNING - 1241137 - [Target] - Partition definition is not valid: [Cell count mismatch: [1279464568200] area for slice [1] members per dimension [63 1 2 1 6 26 7 245 1 37955 ]].
OK/INFO - 1053012 - Object [25586652] is locked by user [PGC_ADMIN].
OK/INFO - 1053012 - Object [11329970] is locked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [25586652] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [11329970] unlocked by user [PGC_ADMIN].
WARNING - 1241137 - [Source] - Partition definition is not valid: [Cell count mismatch: [47895484140] area for slice [1] members per dimension [63 1 6 7 2173 2 17 1 245 ]].
OK/INFO - 1053013 - Object [Pgc_esp] unlocked by user [PGC_ADMIN].
OK/INFO - 1053013 - Object [Pgc_mond] unlocked by user [PGC_ADMIN].
OK/INFO - 1051037 - Logging out user [PGC_ADMIN], active for 0 minutes.
OK/INFO - 1241124 - Partition replaced.
d)Rerun the Partition script again
The same error appears.
Tx to your help.
Regards,
Oliv.

Re:- SAP GUI - Need to understand what is installed as part of GUI

Dear experts,
I need to understand what is installed as part of the SAP - GUI installation for windows like what are all the ocx/ dlls installed, ini files, changes in services files and change in registry things like that.
Does any one has the details. Please help
Warm Regards

Hi,
Please check this links.
This might solve your queries.
http://www.oit.duke.edu/techsupport/sap/sapgui/win/index.html
http://web.mit.edu/sapr3/sw_dist/winstruct.html
http://info.cba.ksu.edu/mchaney/sap.doc
Please reward if useful
Thanks.

Need help!! How to use super in equals() method and makeCopy() method?

This is my Name class:
class Name {
    private String title;
    private String name;
    public Name(){
         title=" ";
         name=" ";
    public Name(String title){
         setTitle(title);
         name=" ";
    public Name(String title,String name){
         setTitle(title);
         setName(name);
    public void setTitle(String title){
         this.title=title;
    public String getTitle(){
         return title;
    public void setName(String name){
         this.name=name;
    public String getName(){
         return name;
    }   This is my Person Class
class Person extends Name{
    private String address;
    private String tel;
    private String email;
    public Person(){
         super();
         address=" ";
         tel=" ";
         email=" ";
    public Person(String name){
         super(name);
         address=" ";
         tel=" ";
         email=" ";
    public Person(String title,String name,String addressStr){
         super(title,name);
         setAddress(addressStr);
         tel=" ";
         email=" ";
    public Person(String title,String name,String addressStr,String phoneNum){
         super(title,name);
         setAddress(addressStr);
         setTel(phoneNum);
         email=" ";
    public Person(String title,String name,String addressStr,String phoneNum,String emailStr){
         super(title,name);
         setAddress(addressStr);
         setTel(phoneNum);
         setEmail(emailStr);
    public void setAddress(String add){
         address=add;
    public String getAddress(){
         return address;
    public void setTel(String telephone){
         tel=telephone;
    public String getTel(){
         return tel;
    public void setEmail(String emailAdd){
         email=emailAdd;
    public String getEmail(){
         return email;
     public boolean equals(Person inputRecords){
         boolean equalOrNot=false;
         if(inputRecords.super(getTitle()).equals(title))         //this is wrong
              if(inputRecords.super(getName()).equals(name))           //this is wrong
                   if(inputRecords.getAddress().equals(address))
                        if(inputRecords.getTel().equals(tel))
                             if(inputRecords.getEmail().equals(email))
                                  equalOrNot=true;
         return equalOrNot;
        public void makeCopy(Person copyInto){
             copyInto.super(setTitle(title));             //this is wrong
             copyInto.super(setName(name));           //this is wrong
             copyInto.setAddress(address);
             copyInto.setTel(tel);
             copyInto.setEmail(email);
}How can I correct the wrong part?
I don't understand how to use super in equals() method and makeCopy() method.

Try something like this ...
public boolean equals(Object other) {
if (other==null || !(other instanceof Person)) return false;
Person that = (Person) other;
return getTitle().equals(that.getTitle())
      && getName().equals(that.getName())
      && getAddress().equals(that.getAddress())
      && getTel().equals(that.getTel())
      && getEmail().equals(that.getEmail())
Notes:
* This overrides Object's public boolean equals(Object other), which is (probably) what you meant.
* You don't need to call "super.getWhatever" explicitly... just call "getWhatever" and let java workout where it's defined... this is better because if you then override getTitle() for example you don't need to change your equals method (which you would otherwise probably forget to do, which would probably have some interesting side effects.
Cheers. Keith.

I am trying to "personalize my cs2 software online download with the serial number from my original boxed cd set and it didn't work. I tried using the download serial number and that doesn't work either. Need help!

I am trying to "personalize" my cs2 software online download with the serial number from my original boxed cd set and it didn't work. I tried using the download serial number and that doesn't work either. Need help!

I understand that you have also used the download link & serial number from Adobe - CS2 Downloads, if still the CS2 is not working, then please refer to the system requirement for e.g System requirements | Photoshop
The issue can be that the present operating system might not be compatible with the CS2.
Regards
Rajshree

Need to understand WebAuth using 3850 MA, 5760 MC and 5508 GA

Similar Messages

Maybe you are looking for