Neeeed help please with lan
hello there
i use pppoe to connect to the internet using eth0 as the card
i am trying to share an internet connection with another linux computer via eth1
i do an ipconfig eth1 192.168.1.1 netmask 255.255.255.0 up when i reboot
i have firestarter installed and went through the gui setup but i dont think my eth1 or nat or iptables are set up right.
i can ping eth1 (192.168.1.1) but not the computer connected to it. (192.168.1.2)
i have given it permission through firestarter, but still cannot get through.
it worked in debian. just one last hurtle to being able to use Arch permanently.
here is the rc.conf
lo="lo 127.0.0.1"
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
#eth1="eth1 192.168.1.1 netmask 255.255.255.0"
INTERFACES=(lo !eth0 !eth1)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# (prefix a route in ROUTES with a ! to disable it)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Daemons to start at boot-up (in this order)
# (prefix a daemon with a ! to disable it)
DAEMONS=(syslog-ng hotplug !pcmcia adsl iptables network netfs httpd crond)
and ifconfig
eth0 Link encap:Ethernet HWaddr 00:50:BF:93:D0:81
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:308 errors:0 dropped:0 overruns:0 frame:0
TX packets:291 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:231087 (225.6 Kb) TX bytes:27930 (27.2 Kb)
Interrupt:16 Base address:0x2000
eth1 Link encap:Ethernet HWaddr 00:11:D8:2B:41:A7
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::211:d8ff:fe2b:41a7/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0xec00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:160 errors:0 dropped:0 overruns:0 frame:0
TX packets:160 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:11847 (11.5 Kb) TX bytes:11847 (11.5 Kb)
ppp0 Link encap:Point-to-Point Protocol
inet addr:63.97.188.33 P-t-P:63.97.188.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:268 errors:0 dropped:0 overruns:0 frame:0
TX packets:251 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:222731 (217.5 Kb) TX bytes:19948 (19.4 Kb)
and modprobe.conf
# OSS Compatibility
install snd-pcm modprobe -i snd-pcm ; modprobe snd-pcm-oss ; true
install snd-seq modprobe -i snd-seq ; modprobe snd-seq-oss ; true
# --- BEGIN: Generated by ALSACONF, do not edit. ---
# --- ALSACONF verion 1.0.8 ---
options snd device_mode=0666
alias snd-card-0 snd-via82xx
alias sound-slot-0 snd-via82xx
# --- END: Generated by ALSACONF, do not edit. ---
alias eth0 via_rhine
alias eth1 8139too
any ideas on how to set up nat here ? i need to share the net with the other computer.
thanks
Not quite sure why you want to start your interfaces manually (eth0, eth1 are commented out and interfaces has a "!" before both). Perhaps adding a route during startup before adding interfaces manually is stopping things working?
Try stopping the firewall, probably:
/etc/init.d/firewall stop
do a "route -n"
mine gives
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0
0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0
[root@night rc.d]#
To get an internet connection working requires only three things:
an interface
a default route/gateway
a name server
Once you've got an interface, you should be able to "ping" that interface 192.168.1.1 and (I believe) anything on that subnet 192.169.1.2 to 192.169.1.254.
Once your got a default route/gateway, you should be able to ping any IP address such as 66.249.87.104 (www.google.com)
Once you've got your name servers IP addresses in /etc/resolv.conf you should be able to lookup and ping www.google.com
Similar Messages
-
Help please with FaceTime. My built in app seems to have disappeared.
If K Penguin's suggestion doesnt work, you will have to go to you iTunes and do a reset, that is if you do not have it in your back up library.
-
Little help please with forwarding traffic to proxy server!
hi all, little help please with this error message
i got this when i ran my code and requested only the home page of the google at my client side !!
GET / HTTP/1.1
Accept: image/gif, image/x-xbitmap, image/jpeg, image/pjpeg, application/vnd.ms-excel, application/vnd.ms-powerpoint, application/msword, application/x-shockwave-flash, */*
Accept-Language: en-us
UA-CPU: x86
Accept-Encoding: gzip, deflate
User-Agent: Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; InfoPath.2; .NET CLR 2.0.50727)
Host: www.google.com
Connection: Keep-Alive
Cookie: PREF=ID=a21457942a93fc67:TB=2:TM=1212883502:LM=1213187620:GM=1:S=H1BYeDQt9622ONKF
HTTP/1.0 200 OK
Cache-Control: private, max-age=0
Date: Fri, 20 Jun 2008 22:43:15 GMT
Expires: -1
Content-Type: text/html; charset=UTF-8
Content-Encoding: gzip
Server: gws
Content-Length: 2649
X-Cache: MISS from linux-e6p8
X-Cache-Lookup: MISS from linux-e6p8:3128
Via: 1.0
Connection: keep-alive
GET /8SE/11?MI=32d919696b43409cb90ec369fe7aab75&LV=3.1.0.146&AG=T14050&IS=0000&TE=1&TV=tmen-us%7Cts20080620224324%7Crf0%7Csq38%7Cwi133526%7Ceuhttp%3A%2F%2Fwww.google.com%2F HTTP/1.1
User-Agent: MSN_SL/3.1 Microsoft-Windows/5.1
Host: g.ceipmsn.com
HTTP/1.0 403 Forbidden
Server: squid/2.6.STABLE5
Date: Sat, 21 Jun 2008 01:46:26 GMT
Content-Type: text/html
Content-Length: 1066
Expires: Sat, 21 Jun 2008 01:46:26 GMT
X-Squid-Error: ERR_ACCESS_DENIED 0
X-Cache: MISS from linux-e6p8
X-Cache-Lookup: NONE from linux-e6p8:3128
Via: 1.0
Connection: close
java.net.SocketException: Broken pipe // this is the error message
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:115)
at java.io.DataOutputStream.writeBytes(DataOutputStream.java:259)
at SimpleHttpHandler.run(Test77.java:61)
at java.lang.Thread.run(Thread.java:595)
at Test77.main(Test77.java:13)please could just tell me what is wrong with my code ! this is the last idea in my G.p and am havin difficulties with that cuz this is the first time dealin with java :( the purpose of my code to forward the http traffic from client to Squid server ( proxy server ) then forward the response from squid server to the clients !
thanx a lot,
this is my code :
import java.io.*;
import java.net.*;
public class Test7 {
public static void main(String[] args) {
try {
ServerSocket serverSocket = new ServerSocket(1416);
while(true){
System.out.println("Waiting for request");
Socket socket = serverSocket.accept();
new Thread(new SimpleHttpHandler(socket)).run();
socket.close();
catch (Exception e) {
e.printStackTrace();
class SimpleHttpHandler implements Runnable{
private final static String CLRF = "\r\n";
private Socket client;
private DataOutputStream writer;
private DataOutputStream writer2;
private BufferedReader reader;
private BufferedReader reader2;
public SimpleHttpHandler(Socket client){
this.client = client;
public void run(){
try{
this.reader = new BufferedReader(
new InputStreamReader(
this.client.getInputStream()
InetAddress ipp=InetAddress.getByName("192.168.6.29"); \\ my squid server
System.out.println(ipp);
StringBuffer buffer = new StringBuffer();
Socket ss=new Socket(ipp,3128);
this.writer= new DataOutputStream(ss.getOutputStream());
writer.writeBytes(this.read());
this.reader2 = new BufferedReader(
new InputStreamReader(
ss.getInputStream()
this.writer2= new DataOutputStream(this.client.getOutputStream());
writer2.writeBytes(this.read2());
this.writer2.close();
this.writer.close();
this.reader.close();
this.reader2.close();
this.client.close();
catch(Exception e){
e.printStackTrace();
private String read() throws IOException{
String in = "";
StringBuffer buffer = new StringBuffer();
while(!(in = this.reader.readLine()).trim().equals("")){
buffer.append(in + "\n");
buffer.append(in + "\n");
System.out.println(buffer.toString());
return buffer.toString();
private String read2() throws IOException{
String in = "";
StringBuffer buffer = new StringBuffer();
while(!(in = this.reader2.readLine()).trim().equals("")){
buffer.append(in + "\n");
System.out.println(buffer.toString());
return buffer.toString();
Edited by: Tareq85 on Jun 20, 2008 5:22 PM -
Can anyone help please with my Time Machine, I have been getting the following message The backup disk image “/Volumes/Mac Backup/Stephen Smith’s iMac.sparsebundle” is already in use.
See > http://pondini.org/TM/C12.html
-
Help please with 2006 Macbook 13inch, for tv hook up.
Help please with 2006 Macbook 13inch, to hook up to tv for streaming. The display works through VGA but the audio isn't working. Got a plug that goes into headphone jack on computer and connects into the audio jack on the back of tv but no sound. I'm not quite sure what the issue is, whether its the wrong plug, the tv, or the computer. Best Buy says this is the right plug and it seems that it would be, but who knows. If anyone has any experience in this, I would appreciate the help!
Make sure those audio plugs are matched with the VGA plug. With your MacBook running something with audio switch between your sources on the TV Component, Composite and such. See if the sound is coming from another source. If so then you've got your audio plugs in the wrong jacks.
Also could you post the make and model number of your TV. -
I need to install the ADB Interface for the X2 onto my computer. Does any one know how or where I can get this driver?
<Duplicate post. Please see Help Please with Driver for any replies. This post will be closed.>
-
Need Help Please with Flash Professional - No Cursor Change on Buttons/Links in Mac OS
Hi Folks, I am relatively new to Flash Professional but I recently built a very nice flash website with very little problems. I noticed after I uploaded my site to my server, that my mouse cursor did not change from an arrow to a finger on any of my buttons. It did change on the hyperlinks, but not on the buttons. Everything still worked fine but there was no indication to the user that an object was in fact an interactive button. I found this code: button1.buttonMode = true; button1.useHandCursor = true; and inserted it for all my buttons and that seemed to fix everything, I tested the site on firefox, ie, and safari. I am using a PC with windows 7. When I went to check the website on a Mac powerbook, the cursor did not change on any of the buttons and it does not change on any of my hyperlinks either. I have searched all over trying to find a solution and have had no luck. Can anyone please help me with this problem or point me in the right direction? Any advice would be very much appreciated. Thanks so much!!!
Thank you so much for replying! I did in fact let flash professional create the HTML page for the site and have not altered it at all. Would you have any other suggestions as to why it's not displaying my links/buttons on a Mac? I checked out the browsers Firefox, ie, and safari on my pc, but looking thru safari on the Mac, the cursor does not change on any of my links or buttons. Thanks again so much for the reply, nice to hear from a human instead of reading thousands of posts! Very much appreciated!!!!!
-
Help please with my navigation buttons
Can anyone please help me with my vertical navigation buttons. I'm trying to set up my nav bar so that all the buttons have a background image (button.jpg) behind them at all times and the only thing that changes when touched or the mouse rolls over them is that the colour of the text changes, except when the sub buttons appear, because the name of some of the sub buttons are so long i have created another button image that is longer (button2.jpg), i only want this to appear on sub buttons otherwise the buttons will end up taking most of the pages space. I'm having great difficulties getting the sub buttons to appear with the correct image (button2.jpg) and am getting increasingly frustrated with it, can anyone please help!!!
www.milesfunerals.com/index2.htmlindex2.html is a broken link for sure. The main index page looks like it's working fine.
A little styling critique if it's okay... Personally I'd have gone with a CSS or Javascript multi-level menu across the bottom of the header. Saves visitors from having to scroll all the way down the page to see every menu item. And I'd rethink the color of the "Miles & Daughters" in the header image. It kinda gets lost in the roses.
If you have a link to the "broken" page please put it up so we can analyze it. -
Help please :) with do not disconnect.
I disconnected my ipod and I still get that "Do not disconnect message" And it doesnt even flash.
Can somone please help me with thisTry Resetting your iPod. Hold down the MENU and SELECT (centre) buttons for five or ten seconds until you see the Apple logo appear then the menu button to go to the normal display. Have a look at this link as well:
iPod won't turn on
iPod stops responding or will not waken from sleep -
Urgent help please with MIDI pedal
I just got an old awesome midi pedal called the X-15 Ultrafoot.
The pedal has two expression pedals, and 10 pushbuttons/pads. (and two buttons to cycle through additional banks, and a "mode" and "bypass" button)
Somebody please help I am on the verge to having amazing control.
What I want to do is have each pushbutton be assigned to a parameter, which is easy to program. Then I want to make the expression pedal(s) also be assigned to that last selected parameter. How do I do this?
How can I make the expression pedals control over the parameter remain exclusive to just the last selected parameter?!
Somebody save me please thanksmr kglad i really hope my ( too many replies and questions ) don't bother you.. but please excuse me if they sound foolish or something im a beginner as mentioned...
There must be something wrong with whatever im doing ... ( im so desperate and since you are the only one who replied on me i really need your help please.. )
1- i published the first fla as a swf (10.3 ) with a button with the code you've given me )
2- i published the second fla as a swf (10.3) with another button with the same code you've given me )
3- i made a main page where there are two buttons.. one for english and one for foreign language
English button with this code :
Engbutton.addEventListener(MouseEvent.CLICK, fl_ClickToLoadUnloadSWF_4);
import fl.display.ProLoader;
var fl_ProLoader_4:ProLoader;
//This variable keeps track of whether you want to load or unload the SWF
var fl_ToLoad_4:Boolean = true;
function fl_ClickToLoadUnloadSWF_4(event:MouseEvent):void
if(fl_ToLoad_4)
fl_ProLoader_4 = new ProLoader();
fl_ProLoader_4.load(new URLRequest("englishformFIN.swf"));
addChild(fl_ProLoader_4);
else
fl_ProLoader_4.unload();
removeChild(fl_ProLoader_4);
fl_ProLoader_4 = null;
// Toggle whether you want to load or unload the SWF
fl_ToLoad_4 = !fl_ToLoad_4;
and the other button with the same code ( the second fla )
IT DOESNT WORK WHEN I TEST THE MOVIE.. the return buttons nor the main ones..why why why why why... ???
i really need your help
THANK YOU in advance -
I'm new to OS X Server and am attempting to set-up a very simple, small network. I've got stuck with HostNames. I gave my Primary DNS Name as 'name.private' during installation. I then read about changeip -checkhostname which, on running, told me my Current HostName was 'name.private', but my DNS HostName was 'Unknown- then lots of digits ending with .lan'. Understanding they needed to be the same, I attempted to change the latter using changeip, but only succeeded in changing the former instead. I've now used changeip again to change that back again. (Will I have damaged anything doing this?)
For someone new to all this, is it essential that the two names are the same and, if so, how do I change the DNS name so that it matches the Current name? (Hope the question makes sense!)
All help gratefully received.There are two elements to DNS, commonly referred to as 'forward DNS' and 'reverse DNS'.
Forward DNS takes a hostname (e.g. 'name.private') and maps that to an IP address (e.g. 10.1.2.3)
Reverse DNS takes an IP address (e.g. 10.1.2.3) and maps it to a hostname (e.g. 'name.private')
changeip can only affect the forward DNS - it changes the name associated with your machine.
Your problem, though, is reverse DNS. You have a hostname (name.private) that maps to an IP address (10.1.2.3), but you don't have reverse DNS setup to map that IP address back to the name.
How you resolve this depends on your DNS setup - how are you running DNS? Do you have your own DNS server? Are you using your ISP?
Is your server on a private LAN or does it have a real-world IP address?
If your server is on a private LAN then you will need your own DNS server in that LAN who knows the LAN address of your server (and any other LAN devices).
If your server has a real-world address and you're using your ISP for DNS resolution, you probably need to talk to your ISP about reverse DNS for your IP address. -
Help please, with port forwarding settings
I have an MSI RG60 wireless router (Ethernet hard wired to my XP Home PC) and don't know what settings to use for port forwarding, to enable my WinMX and BitTorrent clients to work successfully.
I have the port numbers, and assume that this information goes in the Service Port box, i.e. 6699, or 6881-6889.
I know which ports are TCP and which are UDP, but I don't know what IP address to enter or which Common Service Port type to choose. Can anyone help please?
I'm pretty sure that other settings in my PC are OK as I have successfully been running a Belkin router for a couple of years, and have only replaced it with the new MSI unit due to reliability problems.It does indeed have port triggering, but it wants incoming and trigger port protocol info, along with trigger and incoming port numbers.
How can I type ipconfig into either of teh clients...WinMx or Bit Torrent? -
Help Please With iPod Player On My 3GS
Hello, Could anyone help me with a problem with my iPod part of my iPhone 3GS. The iPod will start to play my desired Playlist, but during the playback, the track album covers forget the last played track and franticly search for it. The album covers can rotate for ever and eventually lock the phone up and steel the album cover images at random. I have to then re-sync with iTunes to get them back. My last 3G phone did the same thing and I had it replaced, but still the same with the new 3G. Now I have a new 3GS, so the problem must be in iTunes Folder. I have a lot of tracks & platlists so I don't want to rush to reformat iTunes. Any ideas please? Jeff
I'm having the same issue - did you ever find a solution?
-
Hi, I have a bunch of logos in a file and want to animate with caurina, so I had create a timer to show ( fade in - fade out) the logos one by one;
I had previously fade all the logos with alpha =0; but don´t any idea about how to call it inside the caurina function. my logos all are called logo1, logo2,logo3 etc and I try it to create a variable to hold a number and them put the first part of the name(logo) + the variable to call the movieclip but it didn´t work.Please if someone could help me with this problem.
//this variable hold the 2nd part of the name
var logoContador:Number = 1;
var miTimer:Timer = new Timer(3000);
miTimer.addEventListener(TimerEvent.TIMER, goTimer);
function goTimer(TimerEvent:Event):void
Tweener.addTween(logo+logoContador,{alpha:1,time:1,transition:"easeInQuad",});
Tweener.addTween(logo+logoContador,{alpha:0,time:1, delay:1.7,transition:"easeInQuad",});
logoContador++
miTimer.start();yes, you where right it was the extra coma before the end, works very soft and cool, and even using a conditional inside can use it as a loop.
Thanks so much for your help, here is the whole script, could be useful to other people.
import caurina.transitions.*;
//this variable hold the 2nd part of the name
var logoContador:Number = 1;
var miTimer:Timer = new Timer(3000);
miTimer.addEventListener(TimerEvent.TIMER, goTimer);
function goTimer(TimerEvent:Event):void
Tweener.addTween(this["logo"+String(logoContador)],{alpha:1,time:1,transition:"easeInQuad" });
Tweener.addTween(this["logo"+String(logoContador)],{alpha:0,time:1, delay:1.7,transition:"easeInQuad"});
if(logoContador>=6)
logoContador = 1;
else
logoContador++
trace("im runing");
trace(logoContador);
miTimer.start();
//- end of script -
Help please with Mail attachements
Can anyone help please. When I send an email with an attachment such as a jpeg to a Windows user the recipient complains that the attachment is embedded in the email and can not be extracted to forward, or print for example. I end up having to use Entourage for Mac to send attachments which works for them but is a pain to me.
What do I need to do to have truly Windows Friendly attachments?
Thanks in anticipation.When a PC Outlook user gets a jpg you have attached, even clicking USE WINDOWS FRIENDLY ATTACHMENTS will not alter it. We've done several experiments here and it seems that if you select USE RICH TEXT for formatting in mail preferences MAIL determines that you want to imbed the graphic rather than attach it. If you select use plain text, the jpg will attach properly, but you lose any HTML signatures you have set up, which is a problem for me.
If a yahoo mail is sent from the Mail client, it automatically changes to plain text.
I like Mac Mail, but I want control over how the attachments are sent, so I can have my jpg not imbedded and my HTML signature.
Nancy
Maybe you are looking for
-
I NEED SOME ASSIGNMENTS! TO TEST OUT MY SKILLS!
hey people, i have learned about if, for, and System.in.read() and stuff like that, can someone give me a project for me to work on? like homework to test out my skills? thanx
-
How do I get rid of a false paper jam notice on officejet Pro 8500 909A?
I called tech support and viewed paper jam video. Did all the recommended steps however paper jam message continues to be displayed. There is absolutely no paper jam any where. Can someone suggest what else I can try to resolve my problem.
-
Re: Invalid user ID/Password with OVI Sync
I have same problem on my 5800xm. When I try to sync to OVI server from phone with WIFI. Can anyone help me? Message Edited by spark11 on 22-May-2009 01:04 PM
-
How do I eliminate old addresses from my email list?
How do I eliminate old addresses from my email list?
-
Version conflict while targeting a vi to RT engine
When i am targeting a vi to Labview RT engine the message "Version Conflicts between Host Labview and RT engines" is coming. I am using a CFP-2100 and want to run a vi on it. (No PC should be connected with it) After targetting how will i execute it