Neo 2 865PE Setup Options-Opinions Wanted

Hi, I finally got my new PC set up and I have some setup questions I'd like to get some opinions on:
1) My Hard drive is an ATA133 from Maxtor. Is it better for me to use the IDE1 slot or the Promise IDE3 slot? If I use the IDE3 slot, I will be able to run all of my IDE using peripherals as masters and I wont have to slave anything.
2) Sound- Is the onboard sound better then a Creative Labs Soundblaster Live card?
3) Bios Settings....what are the best performance settings I should use considering the following hardware:
- MSI Neo 2 FISR 865PE Motherboar
- 2.6GHZ 800FSB P4 CPU
- two 256MB Giel 533MHZ PC4000 RAM (512MB total)
- Gainward Ti4200 G4 128 MB "golden sample" video card.
I read in Toms Hardware in this article that I should be able to Overclock the BUS to 900 and perhaps 1000 with a setup like the one I have...the only major difference is that I got 512MB of RAM where in the article he uses 1000 MB of RAM.
http://www.tomshardware.com/motherboard/20030812/index.html
Any comments or suggestions are appreciated.

There'll be no difference of ATA100 and ATA133, the speed is not easy or almost impossible to be detected on daily usage.
I'm pretty happy with my NEO2's onboard AC97' chip, it delivers good quality sound for average users like me, regardless in terms of gaming, musics or movies. Unless you want very high quality sound likewise DTS, THX or doing music ripping, then you may need a better sound card like Audigy 2.
Your setup is ok, but be very careful with your RAMs as the NEOs are not yet very stable at support RAMs of more than 400MHz in speed, during the setups, if you're encountering instabilities, I'll recommend you to lower your RAMs speed to 400MHz and lower all latencies and increase the RAMs Voltage to 2.7v, set AGP/PCI Freq to 67.01/33.50Mhz.
All the Best... :D!!!

Similar Messages

Email setup options

Please help friends. I recently purchased a BlackBerry Curve 8320 and when running the setup wizard I mistakenly selected the option 'I want to skip email setup' thinking that I could go back and do this at a later time. Now, I am unable to set up my personal email accounts as the option 'I want to create or add an email address' is missing in the wizard. The only option I have apart from skipping is 'I want to use a work email account...etc'. Also, I cannot find the setup internet email icon in the home screen menu. I need help urgently. Thanks.

Both of you need to make sure you are subscribed to a BlackBerry Data Plan with your carrier. You must have that for the "personal email set" icon to appear. You need to call your carrier and get that Data Plan put on your account.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Don't Have Personal Email Setup Option

When I go to to "Email Setup" in the "Setup Wizard" on my 8100 Pearl, I only have one email type option that says "I want to us a work email account with Blackerry Enterprise Server".   I don't get the option of selecting the "Blackberry Internet Service Email Options" which is the option I want so I can use my personal email Pop3 type email.

pmagdy wrote:
Dear Sir,
i've tried your solution but it didn't work for me .any other idea how to solve that error ?
Hi and Welcome to the Forums!
To use the proprietary RIM Push email capability, you must have an adequate data plan from your carrier. The carriers host BIS for their BB users. Typically, BIS is not available via generic data plans. Many carriers call what is necessary The Blackberry Data Plan. Whatever they call it, it is the carrier who delivers BIS to their BB users -- contact them for assistance. Once you have a BIS-capable data plan on your BB (at whatever fees your carrier will charge, btw), you will then have Personal Email added to the email setup wizard.
http://www.blackberryfaq.com/index.php/What_do_I_need_a_Data_Plan_for%3F
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

If i selected to "Create a new backup" and then cancelled that option but want to go back and select "Inherit backup history"; how do i go back and do that since now when i plug in my HD, that option doesn't appear anymore?? Any Help?

If i selected to "Create a new backup" and then canceled that option but want to go back and select "Inherit backup history"; how do I go back and do that since now when I plug in my external hard drive, that option doesn't appear anymore?? Any Help? I bought a MacBook Air, but decided to return it for the newest model, and I wanted to back it up so that I can then back it up on my new MacBook Air. I didn't understand the option to Inherit or start a new back up, and therefore selected the option to create a new backup. I believe I should have selected to Inherit backup history so that when i back it up on the new MackBook Air, it appears the same as the one I'm returning.... Is there anyway that i can re-select the option to Inherit backup history for time machine?

Thanks for sharing this link.
I've posted a question here https://discussions.apple.com/message/22049103#22049103 describing my situation. Are you able to suggest me the right option?

I have a problem with my viber.It has stopped working.I tried reinstalliing it again .On the setup option after entering my phone number and continuing ..it either exists or gives no service message .

I have a problem with my viber.It has stopped working.I tried reinstalling it again .On the setup option after entering my phone number and continuing ..it either exists or gives no service message .My other applications are working fine ..other applications that require internet too are working fine.

Please get in touch with Viber's customer support.

DRAM wound too tight??????? Neo 865PE Board Advice needed

RapidShare Account-ID: 14334524
Password: QfYkRMdt
First - My computer is normally rock solid with no problems.
I turned my computer on today and it would not even boot to the BIOS.
It was if there was no power going into it but then it started to boot for about 1 second
then died. I tried again and the same thing kept happening.
I opened it up, checked the Main Board, reseated the graphics card and power cables.
This time it booted but before the bios kicked in it gave the following message:
'DRAM is wound too tight'.
I have not changed anything in the BIOS as I would not know what to change but
it then booted to the BIOS and under the power settings it says the following:
Dynamic Over Clocking = Private
Performance Mode = Slow
CPU Ratio Selection = Locked
DRAM Frequency = Auto
Spread Spectrum = Disabled
Adjust CPU Bus Clock(mhz) = 200
DDR Clock (mhz) = 333
Adjust AGP/PCI Clock (mhz) = 66.66/33.33
CPU VCORE Adjust = No
DDR Power Voltage = 2.50v
?GP Power Voltage = 1.50v
If anyone can make any suggestions I would be most appreciative as I cannot
afford to loose my computer or any data that is on it.
I'm worried that the Main Board maybe failing or maybe the RAM or PSU?
In case it matters this is what is in my system.
MSI Neo 865PE Board
AMIBIOS V3.31a
2 matched pairs of Kingston HyperX RAM KHX2700K2/1G
Intel P4 3Ghz CPU
Intel ICH5R SSATA
Port 1 = Crucial Solid State Drive (Main OS Drive)
Port 2 = Lite-On SATA CD-RW
IDE Port 1 = 300GB Samsung HD
Promise SATA
Port 1 = WD Caviar Green 1.5TB HD
Port 2 = WD Raptor 150GB HD
IDE Port = Sony CD-RW
Power Supply = Q-Tec 550 Watt Dual Fan Gold
USB Mouse/Keyboard
All housed in a 19" Rack Mount Server case.
Thanks in advance.

thanks for the replys everyone.
I take it then that my problem is the PSU?
I am shocked that you rate the Q-Tec one so badly, it is the one that was supplied
with my computer and has worked with out a problem for about 3 years or so now.
I cant take a chance with it so its going in the bin.
Having done some checking I have located a trusted stockest who has
Corsair VX 550W ATX Power Supply (CMPSU-550VXUK) [CMPSU-550VXUK]
or
Corsair TX 650W ATX SLi Compliant Power Supply (CMPSU-650TXUK) [CMPSU-650TXUK]
for just ubder £80 in the UK.
Are either of these any good and is one better for me than the other considering what
main board I have. Also the new CPU has got to fit in my computer case so its physical size must match the old one.
I am not a modder so this is all a bit alien to me so any tips or hints much appreciated.
Thanks again
Kenny

I would like to change the project page layouts, but setup option in Project Superuser are not available. How can I change the selected page layouts?

Hi
I updated the page layouts for a project in Project Management. Now I woujld like to change those chosen page layouts, but the setup options for the project are no longer available for me to change. How can I update the original chosen page layouts (for performance management) to different layouts or change the chosen layouts to the default (blank) layouts?
Thanks
Chris van de Graaf

AppleMan,
It all began inside the settings of my Sanyo VPC-HD2000A when somehow the selection got switched from 1280 x 720 to that other setting with so-called 25fps. Also, I don't know whether the mishap occurred before or after I took my new footage.
I edited the clips last night and now they are on my blog and channel and they seem ok but slightly fuzzy.
I used a Sanyo VPC-HD2000A .7x wide angle lens with macro and I notice that when I zoomed in to the little sun conure, the picture blurred. I think that might be something that happens when one zooms the focus.
Also, I was born and raised to a teenager in Hawaii, but now Southern California has me in its grip.
-L

I do not have the Print To PDF Setup option

the instructions to intall the Adobe CreatePDF printer are below. I do not have the "Print to PDF Setup option on my Adobe site. Can someone help me with this?
Install Adobe CreatePDF Desktop Printer
In Adobe PDF Pack, click Print To PDF Setup.
Click Download Installer.
Double-click the AdobeCreatePDFDesktopPrinterSetup.exe file you downloaded and follow the prompts to install Adobe CreatePDF Desktop Printer.
Note: You need administrator rights to install the Adobe CreatePDF Desktop Printer.

To install Adobe CreatePDF Desktop Printer:
1. Log into https://createpdf.acrobat.com/signin.html with your Adobe ID and password
2. Select “Convert to PDF” tool from right pane
3. Click “Download CreatePDF Desktop Tool” link
4. Click “Download Installer” button
5. Click “AdobeCreatePDFDesktopPrinterSetup.exe” file
6. During the installation , you need to enter your Adobe ID and password
If your system is Win 7 SP1 please install a hot fix to update inetpp.dll file from http://helpx.adobe.com/acrobat-com/kb/createpdf-desktop-printer-windows-7.html
If you have not installed Adobe Postscript(PS) printer driver please install it:
How to Install PS printer:
1. Open Start menu > Devices and Printer ( or from control panel) and select "Add a printer"
2. Select "Add a local printer"
3. Select "Use an existing port: LPT1: (Printer port)
4. Select any company and any PS printer with Adobe PS printer driver(not clone) such as Xerox and Xerox Phaser 6120PS
thank you.
Hisami

I am trying to set up family sharing and do not have the setup option when logged in, help!

I am trying to set up family sharing and do not have the setup option when logged in, help!

Hello Carney10,
Thank you for visiting Apple Support Communities.
When you say you do not have the setup option for Family Sharing, that seems like you log into the iCloud System Preference but the "Set Up Family" button is not there.
Is your Mac updated to Yosemite?
Family Sharing - Apple Support
iOS 8 and OS X Yosemite are required to set up or join a Family Sharing group and are recommended for full functionality.
Where in the setup are the options not available or working?
OS X Yosemite: Set up Family Sharing
Best regards,
Nubz

Just updated to iCloud, but I can't find the 'purchased' list on the itunes store on my iphone. There's no button for it on the toolbar or under the 'more' option. Want to play/download my puchased music via iCloud on my iPhone.... Help someone please?!

Just updated to iCloud, but I can't find the 'purchased' list on the iTunes store on my iPhone. There's no button for it on the toolbar or under the 'more' option. Want to play/download my puchased music via iCloud on my iPhone.... Help someone please?!

Hi again Limons,
just got your last reply per mail, re: 'presently only available in the USA.'
Unfortunately, you're right. Just found this article: http://www.digitalmusicnews.com/stories/061011icloud
seem like it's going to be a while before this gets sorted out . . .
Frustrating outcome to my question, but thanks a lot for helping me sort out what the problem was :-)
All the best to you.

Reference monitor seems to be missing the setup option

http://imageshack.us/f/11/referencemonitor.jpg/
My reference monitor seems to be missing the setup option also it is displaying in a format I do not understand.

I'm based in th UK and working with PAL mini DV. I imported the footage in and then created the sequences using a clip, so the sequence settings should be correct and having checked them, it seems they are. Admittedly, I've never used this function before and this: http://library.creativecow.net/articles/devis_andrew/YC-Waveform-graph-Premiere-Pro/video- tutorial is my frame of reference. The problem I have is I cannot convert the scale he is working with (IRE) to what I'm working with (V).

875P Neo-LSR Setup problems

I posted this message last night but I think it got lost in space.
My System
MSI 875P Neo LSR
Intel 2.4C with H/T
2 X 512 Infineon memory sticks
Enermax 350W P/S
ATI AIW 8500DV
Seagate S ATA 120 H/D Partition with 85/35 partitions on SER1
Western Digital P ATA 80 H/D on IDE 1
LG 52 X CD ROM on IDE 2 primary
LG DVD/CDRW Combo IDE 2 slave
19 Samsung Syncmaster
I am having problems with my new 875P LSR. Installed O/S and software using FAT 32 and it wiped on 2 occasions. Could not boot up trying all the sugestions on the web. Using Partition MAgic rescue disk I could still see the drives and was able to check for errors but when I used my old 98 boot disk C: came up with a message of invalid media but D: was still readable? During both the previous setups I used the F6 option and loaded the Intel raid XP driver for ICHR, was this the reason for my loss of system.
On my third try I used the same partitions but did not use the F6 option and also formatted in NFTS (by accident). Everything appeard to be working so far BUT!!!!!. I don't want the system to do over clocking I just want a secure setup for stability in normal use. I do not play games, I use the inter4net, edit my home movies and normal word processing,
Questions
What am I doing wrong?
What should the cofigreration for the bios onboard ID chip be. I have Mine set in Native mode, P ATA + S ATA, NO, NO, Both, S ATA 1st channel, S ATA PO1 PO2 Raid NO
Do I need to use the Intel IAA driver -or- does XP have drivers -or- do I have to download some other driver or controler for the S ATA.
Can anyone suggest a better layout for my system and how can I tel if the computer is operating with the proper drivers for S ATA, P ATA, H/T and all the other gagets on board. Any suggestions and advise will be appreciated
Swan705 in Ontario Canada

Hi back
Thanks again for the response, followed your instructions now I show a 82801eb under the controler section. Is that all I needed? Another question I like to keep a copy of windows 98 se on my other drive and would like to use the F11 key to boot to it. Is there a procedure of installing it so I don't screw up my XP system. I use a disk tray to keep the drive in so I can take it out for safety as I also store backups of my personel files on it. Your sugestions are really appreciated. Swan705

Crystal 2008 - New Page Setup options - need explanation please

I have been unable to locate documentation on the new Page Setup screen for Crystal 2008. I am specifically looking on detailed documentation about the following check boxes:
Printer Options:
     No Printer
Page Options section:
     Dissociate Formatting Page Size and Printer Paper Size
Margins section:
     Adjust Automatically.
Can someone please detail for me these options. I'd like to know why I would use them and how do they work when combinations of them are selected. I am most interested in the second option (above), but would like explanations about all of them.
Thank you.

I do not think the No Printer option is valid for us as our reports are not web based.
Does the Adjust Automatically apply to the reports as they are run from a runtime client? or does this just adjust for design mode?
This is why I am asking about the 'Dissociate Formatting Page Size and Printer Paper Size'. It sounds like this is the setting we may want to check when creating our reports before we distribute to runtime clients.
Here is why I want to know.
We develop our reports to fit 8.5 inch x 11 inch paper. We distribute our reports to our clients along with the runtime merge modules. We have a VB.Net 2005 program that our non-vb.net software application executes in order to print the reports (using the Crystal for .NET methods, etc.) from our software application.
Some of our clients are in Europe. They use A4 paper. We have re-designed some of our reports so the fields will fit within both paper sizes (8.5x11 and A4). However, we have over 500 reports we distribute, so we have not modified all reports. Therefore, prior to Crystal XI, we recommended to our runtime users that if the data on the report did not fit on the A4 paper (it was truncated), then they need to go into the printer properties (from the printer dialog box...these are users running the report, not developers) and change the report from portrait to landscape before they print. This would print the report landscape with data across 8.5", and then white space on the right/remainder of the page, but all the data would print, nothing truncated. After we installed Crystal XI, using this option of selecting landscape at print time, no longer worked. The report would print with the orientation in which it was created (in our case portrait) regardless of what the user selected from printer properties.
This is why I am asking about the 'Dissociate Formatting Page Size and Printer Paper Size'. Can someone at SAP elaborate on this please?

Window setup option on the boot menu after fixing Blue Screen Errors

Hello Everyone, this is my firs t request.
I spent two days fixing the Blue Screen Errors (BSoD) on my computer but one thing keeps bothering me is that everytime I start or reboot my computer, it gives me TWO OPTIONS; 1. windows xp home edition 2.windows setup (default). I want to disable the second option. I had attempted to re-install windows but later changed my mind, and found an alternative to fix the Blue Screen Errors. I believe the reason Blue Screen Errors (BSoD) showed up was that I had created a new user profile and copied over old user profile files so improperly that it duplicated drivers, and gave me a list of STOP errors with blue screens for both new and old users.
The bootini file currently shows:
[Boot Loader]
Timeout=5
Default=C:\$WIN_NT$.~BT\BOOTSECT.DAT
[Operating Systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Home Edition" /noexecute=optin /fastdetect
Does anyone know what to edit for the bootini file so that I don't get two options at the startup??? My system details are:
IdeaPad, S10-4231
Windows XP Home Edition SP3
4-year old
Thanks,
Lenovo User

Hi
Welcome To Lenovo Community
As per the Default Sample of Boot.ini the default value after timeout section needs to be modified
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Home Edition" /fastdetect
Before making any changes please save a copy of Boot.ini
Save a Backup Copy of Boot.ini
<script type="text/javascript">//
loadTOCNode(2, 'summary');
// </script>
Right-click My Computer, and then click Properties.
-or-
Click Start, click Run, type sysdm.cpl, and then click OK.
On the Advanced tab, click Settings under Startup and Recovery.
Under System Startup, click Edit. This opens the file in Notepad ready for editing.
In Notepad, click File on the Menu bar, and then click Save As.
Right click in an empty area of the Save As dialog box, point to New in the context menu, and then click Folder.
Type a name for the new folder, for example temp, and then press the ENTER key to create the folder named temp.
Double-click the new folder named temp, and then click the Save button to save a backup copy of the Boot.ini file.
Please try modifying the following
Default=C:\$WIN_NT$.~BT\BOOTSECT.DAT
to
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
Hope This Helps
Cheers!!!
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with Kudos!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follo @LenovoForums on Twitter!

Photoshop Script - save as PDF, how to programmatically use "Use proof setup" option

Hello,
I'm trying to create a jsx script for Photoshop CC that will automaitically convert the given file to PDF format. The requirement is that the PDF must be saved using two options available on "Save as" dialog:
- Use proof Setup: Working CMYK
- ICC Profile: U. S. Web Coated (SWOP) v2
(screenshot: http://screencast.com/t/hnnVejK5)
I couldn't find any examples on the Internet. I experimented a bit and created the following script, it saves the pdf, but it does not seem to use the mentioned options.
app.displayDialogs = DialogModes.NO
var fileRef = File("C:\\test\\7000_tif_colors.tif")
var docRef = app.open(fileRef)
var fileName = "C:\\test\\7000_tif_colors.pdf"
pdfFile = new File(fileName)
pdfSaveOptions = new PDFSaveOptions()
pdfSaveOptions.PDFCompatibility = PDFCompatibility.PDF14
pdfSaveOptions.downSample = PDFResample.NONE
pdfSaveOptions.colorConversion = true
pdfSaveOptions.profileInclusionPolicy = true
pdfSaveOptions.embedColorProfile = true
pdfSaveOptions.destinationProfile = "U.S. Web Coated (SWOP) v2"
pdfSaveOptions.preserveEditing = false
pdfSaveOptions.layers = false
pdfSaveOptions.outputConditionID = "Working CMYK"
docRef.saveAs (pdfFile, pdfSaveOptions, true, Extension.LOWERCASE)
docRef.close (SaveOptions.DONOTSAVECHANGES)
Thank you in advance for any help.

You may want to post over at
http://forums.adobe.com/community/photoshop/photoshop_scripting?view=discussions
Have you recorded the operation with ScriptingListener.plugin and tried using the resulting code?

Neo 2 865PE Setup Options-Opinions Wanted

Similar Messages

Maybe you are looking for