Neo 875 Bios setup for RAID - HELP PLEASE

Have tried just about everything. I am unable to access the DISK ARRAY BIOS setup. Any ideas???

Quote
Originally posted by Flyboy747
Have tried just about everything. I am unable to access the DISK ARRAY BIOS setup. Any ideas???
hi
have you enabled the RAID chip in your BIOS?
good luck

Similar Messages

  • My Ipad has been locked (after wrong passcode) and tried to connect to Itunes but no success. Much appreciated for your help please.

    Dear Sir/Madam,
    I tried the following but no success:
    1. Unplug the sync cable from device.
    2. Turned off device (slide to power off).
    3. Pressed and hol the Home botton and pluged in the sync cable.
    4. Hold Home button until "Connect to iTunes" but this message did not appear
    So couldn't go any further than this.
    Looking forward for your help please.
    Kind regards,
    GS

    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    This is an iPad user to user forum. Apple doesn't read or respond.
     Cheers, Tom

  • Need a little help in settings for RAID-0 please

    Hey folks I am trying to over-come some issues and I believe my raid settings are not right. In BIOS what should they read like. I have 2 drives.
    Raid -Enable (got that one right )
    IDE Primary Master Raid-Enable or Disable?
    IDE Primary Slave Raid-Enable or Disable?
    IDE Secondary Master Raid-Enable or Disable?
    IDE Secondary Slave Raid- Enable or Disable?
    SATA1 Raid-Enable or Disable?
    SATA2 Raid-Enable or Disable?
    SATA2 Raid-Enable or Disable?
    SATA3 Raid-Enable or Disable?
    SATA4 Raid-Enable or Disable?
    Thanks for the time and help folks.
    System spec.
    Athalon 64 X2 3800+ Manchester
    Motherboard: MSI KN8-F nForce 4 SLI (MS 7185)(red board)
    Cooling: ARTIC
    Memory: 1 GB Kingston CAS 2.5 value ram (2x512 dual channel DDR400-PC3200 -BIOS set at 2T)
    Video Card: SAPPHIRE X1800XT 256
    Harddisk: 2 Seagate Barracuda 7200.8 in raid 0
    CD/DVD Drive: Sony 810 dl dvd burner/MEMOREX 16X16 DVD DUAL LAYER
    CRT/LCD Model: Samsung 19 SyncMaster
    Case: Antec SonataII
    Sound Card: X-FI FATLITY cambridge dolby digital amp&speakers
    PSU: 450 watt True Power inc. with case
    Software: XP SP2
     

    Quote from: nascarmike on 29-January-07, 07:10:51
    When I reset BIOS they came back all enabled ( primary and secondary and all 4 SATA. How do I determine which channels are in use? Also which area in BIOS allows me to change from 64 to 16K? I'm a little lost noob (or due to age maybe some Alzimers?)thanks in advance.
    RAID is disabled by default.
    Enable SATA as RAID for channels where are your HDD detected: (example: if you are connected your SATA disks to SATA1 & SATA2, configure RAID for  SATA1 & SATA2.)
    after raid is enabled, and configured property leave BIOS (SAVE AND EXIT) you will need to setup your raid configuration, by pushing F10 to enter Raid setup after post:
    hit F10 when menu popup to enter RAID utility.
    •     Now select Striping, Mirroring, Striping+Mirroring, Spanning.
    •    Next push the tab key, and select the striping block size you want.
    •    Push the tab key again, and select the hard drives you want to include in the Raid array.
    •    Then push F7 to save and finish the Raid array.
    Choice Stripping mode for RAID mode and add both HDDs to array. select "Striping Block" to 16k.
    then hit F7 when you done. at next menu make your array bootable by selecting array and hit "B":
    config with "Y" when asked.
    NOTE: Information on both Disk will be lost.

  • I need BIOS setup for 5005-S504

    Hello,
    I no longer have the original disks, the laptop was OFF for 8 years and the CMOS battery was dead. Windows was corrupt and I installed Win Vista. I need to access the BIOS but the Win XP HardWare utility download won't run in VISTA. Hitting ESC when it boots doesn't work. F2 doesn't either.
    How can I access the BIOS setup screens? Is their a reset button somewhere on the motherboard? 
    Any help appeciated.

    Satellite 5005-S504
    You might try one of the methods mentioned in here.
       BIOS Setup / BIOS settings -- access instructions
    If the Esc key doesn't work, you're probably out of luck. Why Vista?
    Can you boot to DOS, BTW?
    -Jerry

  • Satellite X200 - How to find BIOS setup for Intel Storage Matrix?

    Hi everyone,
    I'm willing to enable the Matrix Storage feature on my Satellite X200-24X. The problem is I can't find any relevant option in the BIOS setup...
    Thanks !

    Hi
    The Intel Storage Manager is a driver and not an option in BIOS. The only option that you have in BIOS is the HDD access mode. There you can change between AHCI and Compatible.
    For AHCI mode that is faster you need Intel Storage Manager driver. For Compatible mode you dont need additional drivers.
    You want to know how to install Storage Manager? Just use the forum search, you will find hundreds of results. ;)

  • Getting error message2324 when downloading the new update for itunes help please

    getting error message 2324 when downloading the latest update of itunes help please.
    Will not let me uninstall itunes from my computer, gives me the message that I don't have access need administrator. ( I am the only user of this computer)
    Thank you
    Chris

    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (Later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    See also HT1925: Removing and Reinstalling iTunes for Windows XP or HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    Should you get the error iTunes.exe - Entry Point Not Found after the above reinstall then copy QTMovieWin.dll from:
    C:\Program Files (x86)\Common Files\Apple\Apple Application Support
    and paste into:
    C:\Program Files (x86)\iTunes
    The above paths would be for a 64-bit machine. Hopefully the same fix with the " (x86)" omitted would work on 32-bit systems with the same error.
    tt2

  • ISync for Mac - Help please!

    I have a Nokia N70 and am trying to update my contacts from my Address Book. I have up-to-date OSX 10.4.10 and iSync 2.4 and the phone is being recognised, so a good start! My problem is that my updated Address Book entries are not being transferred, somehow an old version of my Address Book is being used by iSync.
    I've tried restarting the Mac, clearing all contacts from my phone and sync-ing again (repeatedly), but I still get the contacts from the old version of Address Book loaded into the phone.
    I'm not a Mac expert, can anyone smarter than me help please?
    Thanks for your time.
    MacAndy
    PS Any tips on useful software for making the N70 otherwise more compatible with music and any other areas would be very welcome.

    There's an actions folder. It's your hard drive>library>application support>adobe>photoshop elements>8.0>Locale>en_US (this one is different if you aren't in the US)>workflow panels>actions

  • MSI GT70 0NC Unlocked Bios Request - For me too please

    Hello,
    Can I please get an unlocked bios for my MSI GT70 0NC too? I would love the unlock to apply to the latest bios so I can update and unlock at the same time.
    Can you please unlock everything?
    PM me for the cost please so I can deposit.
    Thank you.
    Details
    Model - MS-1762
    Current Bios
    Version E1762IMS.10M
    Build date  17/06/2012
    EC Version 1762EMS1V4.05
    Build date 04/03/12
    ME FW - 8.0.0.1351
    IGFX VBios - 2126

    Hello,
    I just noticed it is possible to disable the discrete card. That would be very important for me as I use Linux and don't game much so it would save power etc.
    When the bios update happens does it also update the IGFX firmware etc?
    Looking forward to your reply

  • Battery Level Gauge for E61i - Help please

    The battery indicator on the menu of these phones is hopeless and don't appear to be any better in the various themes available. Does anyone know where I can get a good basic battery guage - preferably freeware but I don't mind paying a few ££.
    Thanks for any help.
    Queensparker

    With the headset switched on and connected wirelessly go to:
    Settings > Accessories and you'll see the battery level there.
    If you don't see it you need to make sure your Nokia apps are fully up to date, especially Accessories and Audio. You can find the codes to update them on this link:
    http://discussions.nokia.com/t5/Pool-of-Knowledge/​Nokia-Windows-Phone-8-App-Updates/td-p/1640082

  • The five Rs wont work for me- help please!

    My boyfriend is stuck in Iraq on duty with and Ipod he just bought this month, and it isnt responding to anything. Its a hassel getting the ipod from one country to another so if there is anything that will fix the problem would be awesome! This is what he says its the problem (he cant get online often btw):
    when i try to turn it on with it now plugged into the computer, the apple screen with turn on then it goes to a screen that has a folder with one of these marks ( ! ) and below that it says www.apple.com/support/ipod, then it turns off. and then when i plug it into my computer it does the samething but it does not turn off it just says do not disconnect. my itunes does not reconize my ipod. i tryed the whole 5 R's thing, but the ipod uploader program will not let me restore my ipod, it just freezes up on me.
    (so its a combination of problems- thanks for the help!)
    Also- does anyone know of a good case that will keep anything from getting inside (like sand? cause hes scratching ipod real bad)

    You say you've tried different FireWire ports on the G5 ..but that often seems to be the problem ..or the fix!
    Do you have a 3rd-party FireWire card installed in the G5..? If so, try connecting the cam to one of those ports instead of the built-in ports. Or try pulling out the 3rd-party card, and then try the built-in ports.
    Do you have someone else's codec installed? Toast? Flip4Mac? To avoid those, try creating a new User (..System Preferences>Accounts and press the + at the bottom of the left pane..) then log in as that User instead, and see if it works. If so, you have conflicting software in your main User account.
    However, it's not usually that: it's most often (..with a G5..) a hardware (FW port) problem, by all accounts. [..Even the Apple Store in London couldn't get their FX1 to work with their G5 when I wanted a demo of import times!..]
    So there has to be a solution (my FX1 works fine with PowerBooks and a Mac mini, but I don't have a G5) ..I'd suspect a bad interaction between different ports - or recently-connected FW hardware - on the G5.
    P.S: "..Then viola... iMovie crashes and all goes downhill from there.." Try removing the viola; it takes up too much space. Try a violin.

  • Gmx email setup can anyone help please

    hi i cant set up my email for gmx on my iphone5 can anyone help please

    What happens when you try? Have you asked for their help on how to set up email on a mobile device?

  • WHAT BIOS SETTINGS FOR RAID 0 MSI NEO4 SLI-F-AMD 3800+MANCHESTER

    What are the M-Board settings for raid-0 I have 2 Seagate 7200.3 500gb drives MSI NEO4 SLI - f board and a AMD 3800+ Manchester. Thanks

    Setting up raid
    http://www.nvidia.com/object/feature_raid.html
    There are two guides here :
    Media Shield User's Guide  PDF
    RAID Floppy Disk Install  PDF
    Most things are covered in thees guides if running a nForce4 system.
     

  • BIOS setup for SSB boot drive and 2 RAID 0 data drives

    I'm  trying to setup my new rig.  I was able to get Win 7 to see all drives when plugged into the white SATA connectors.  This with no BIOS RAID.  If I change the BIOS from AHCI to RAID, Windows fails to boot completely.
    After some research, I tried plugging the SSD boot drive into the JMicron controlled blue SATA 7 connector.  It works.  The 2 WD 640's are in the South Bridge controlled SATA 1-6 connectors (3 & 4).  Windows sees the drives with On-Chip ATA Devices set to AHCI.  I can setup the 640's with On-Chip ATA Devices set to RAID and the BIOS sees them during boot up, but Windows can't.  I did install the RAID drivers as specified in the manual Appendix B.
    My system specs are  in my sig.  I don't see them in preview, so I hope the show up.
    So, what did I miss?  Thanks if advance for any assistance!
    Scott

    I did this from the manual appendix B:
    Installing the RAID Driver Under Windows
    (for Non-bootable RAID Array)
    1. Insert the MSI DVD into the DVD-ROM drive.
    2. The DVD will auto-run and the setup screen will appear.
    3. Under the Driver tab, click on AMD chipset drivers by your need. The AMD chipset
    drivers includes RAID Driver.
    4. The driver will be automatically installed.
    Plus, I installed the JMB36x drive under the RAID button on the MSI CD.

  • PT880 Neo 4 red led, Need your help please!!

    Hello all
    It is my first post and I need your help. Today I purchased a combo P4 3/800 E Box CPU, MSI PT880 Neo FSR Mboard  and DDR 512MB 3200 VS Corsair 400Mhz 184 Pin Dimm from Fry's Electronic. I can not get my system to boot , no beep but only 4 red led and nothing on the screen. I used on my system Enermax 300W with DVD burner, DVD player, 60G HD, SBlive 5.1, ALL in Wonder Radeon 32Mb..After I am following all recommendation in the defferents Topic, I have no luck it won't boot. The 4 red leds are still on. Help me please thank you
    Brono85

    I've just got my Noisetaker 470watts too, it has the same rails as CoolerGiant , but I like CoolerGiant's active cooling system for both CPU and PSU , just that it's too lengthy and my chassis was small in size .
    Back to the topic, likewise anr11 mentioned, you may need a BIOS flash and you can use Memtest86 to test your RAMs out .

  • Setup Problem - Need Help Please!!

    My problem is a low hum eminating from my speakers every time I connect my MPC2000 sampler to my audio interface.
    My setup consists of the MPC2000, a Dj Mixer, and my laptop which has an M-Audio interface which I use to connect the mixer & MPC. Basically, as soon as I remove the cables that connect my MPC or my mixer to my interface, the hum stops. I've tried different cables, new cables, a ground adapter for the MPC to change it to 2 prong, and nothing helps. The only thing that DOESN'T cause this hum when plugged into my interface, is my keyboard, so i'm quite sure the interface itself isn't the problem.
    Does anyone know what might be causing this interference that's resulting in a hum? I have exhausted all my own theories and am desperate for some sort of help! Many thanks in advance!!!

    Hi beirut,
    Try the following:
    1.Put the mpc2000,the dj mixer and your computer all in the same power outlet from the wall.
    2.Go to home despot and buy a few gray-colored ground lift plugs (they must be gray)
    3.With these gray ground lift plugs,lift the MPC2000.test the system.No hum=solved problem.hum still there or different,list the DJ mixer.
    4.Is your DJ mixer hooked up to turntables? If so,you need to ground the turntables to a proper ground.Good turntables have a little wire coming out of them,just for that purpose.
    5.Try turning off any TVs,refridgerators,fluorescent lighting(the ones that look like office lights),and other things around your place,and see if the hum goes away.
    6.Try using a DI box for your DJ mixer,to plug it in to the DI,and then out to the audio interface.
    7.And Most Importantly... RUN AND BUY A DIFFERENT BRAND OF AUDIO INTERFACE!!!!!!!!!! M-Audio...yucky yucky yucky!!!
    Cheers

Maybe you are looking for