Neo2 BIOS 3.3 Disables VIA SATA Raid AND Promise IDE3 RESOLVED

I recently corrputed my VIA SATA Raid installation of Windows by overclocking my FSB. I have since read that you can't do this, and I definitely learned my lesson.
But in the process of attempting recovery, I upgraded my BIOS from 1.8 to 3.3. (I know, didn't really keep up on that =)
Now I have a strange problem. I can't have both the Promise controller ENABLED as well as the VIA SATA enabled. During boot, if the Promise controller is Enabled and has an IDE HDD plugged into it (important!) which was created by this Promise controller a few months ago, the VIA SATA section of BIOS boot does not show up. It will not even show the text where it is looking for attached drives. Herein lies the problem.
Here are a few scenarios. If I unplug all drives from the Promise IDE connector, but leave it enabled, it will proceed to the VIA section of BIOS boot right after the Realtek initialization. It will also show the VIA section of the BIOS boot if I disable the Promise in the Integrated Devices section of the BIOS.
But, if I leave a single drive connected to the Promise IDE connector, and have them both enabled in BIOS (VIA "On Board" is ENABLED and Promise is set to RAID) then the only boot options I see are the Promise section, where it will correctly identify the IDE drive connected to it (remember, it was made a drive by that very same controller chip a few months back) and then proceed to the Realtek initialization. After that, there is no VIA section at all.
Interestingly, if you hit DEL to go into setup anytime during the scenario where there is no VIA init section, the VIA SATA drives do not show up on the Boot Sequence at all. It is like it is not there at all, which I suspected since it wasn't showing up during BIOS boot.
SO. This leaves me with the unfortunate scenario of not being able to use one or the other. The only thing I can think of is that I updated my BIOS revision. Please, is someone able to duplicate this, or is there a known workaround? I would hate to lose half of the functionality of the mboard as far as additional controllers goes.
I will add my config below just in case that helps:
K8T Neo 2
AMD 3500+
2 x Kingston 3500 HyperX 512
Antec NeoPower 480w
2 x 36GB Raptors SATA (Drives I am attempting to run on VIA for boot)
2 x IDE drives (Maxtor 250GB and WD 160GB) on the Promise IDE 3 channel (sometimes anyway =)
2 x CD ROM on IDE 1
2 x IDE drives (WD 60GB and WD 120GB) on IDE 2 (I leave these unplugged during windows install and T/S'ing this problem)
ATI Radeon X800XTPE
I hope that is all you would need to know about the box.
Thanks for your ideas.

Quote from: Tiresmoke on 09-April-05, 22:52:31
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=608&kind=1
I trslly would suggest first though to do a Bios reset and then re-examine the problems if any and let's see if we can track and sort them out.
The first thing I found odd is that you claimed to have updated the Bios from 1.8 and there is no version 1.8 for the Neo2's. Their Bios range starts at 3.0 and that is the lowest number you should have been at.
Second let's take a look at your Bios settings. Typically when you flash a Bios you have to go back and reset the bios again to what is needed for your rig. Otherwise the default settings may not allow you to run your system at all properly.
I appreciate your looking at this with me Tiresmoke. You must be right on the previous BIOS version. It is my original Neo that I am thinking of for 1.8. Now that you mention that, I don't know what the previous BIOS version is, but I am now going to assume it was the original.
Tracking through it though has been strange. Another change I noticed is that my RAM would no longer run at DDR400. It was stuck at DDR333 no matter what I did. I had to move the Kingston 3500 that I had from 1/2 to 1/3 to get it to work. Something must have changed in the BIOS update to make that happen, as it was running fine before that, and differences in operation at that level have nothing to do with whether I corrupted my RAID based windows install.
The boot order is as follows:
1) Promise Controller (Press CTRL + F)
2) Realtek LAN Boot (Press SHIFT + F10)
>
3) VIA RAID Controller.
It is #3 that will not show up if there is a drive attached to the Promise controller. This has got me completely stumped. Is there a direction we can go with T/S'ing this?
Thx.

Similar Messages

VIA SATA RAID Drivers

I lost the floppy disk containing the VIA SATA raid drivers for Windows Installation. My M/B is the KT600 FISR. So I kinda need the drivers as I am setting up a SATA drive.
Can someone please say where I can get the drivers, or email me the attached drivers.
My email is:
[email protected]
Thanks,
Sam

I am worried my floppy drive controller or something on the motherboard is not working. I tried the floppy disk containing drivers and Windows Installer said still said "Please insert the manufactuer's disk", I took out the disc and got the same message.
Then I booted up Windows Installer with the same floppy disk in a different MSI motherboard (a P4 mobo I have) and it detected the drivers fine.
Tried all the updated drivers you specified, and the floppy drive reads fine from Windows and is brand new (same problem with old one which I replaced only to find the same problem :
The mobo is still under warranty, should I give MSI / dabs.com a call?
Sam

VIA K8T800 RAID and Highpoint RocketRAID 1540 PCI card

I've had this old HighPoint SATA RocketRAID 1540 PCI card sitting around for awhile now and I thought I would maybe use it to beef up my system. I am currently running a RAID striping array with a pair of WD 74GB Raptors via the K8T800 chipset (no pun intended) on my MSI K8T Master2-FAR workstation and a pair of 80GB Western Digital drives (separate partitions) that I currently use for storing raw data/projects that can be used to rebuild my system in the event of an OS crash (striping array is a bit more risky so I like having this around). My idea is that I would put the WD 80GB drives on a mirroring array and use them for data storage. The catch is that this coming week I am going to reformat and install a dual WinXP/SuSE boot partition on my Raptor striping array, and I will need to make sure that the mirror'd backup drive is accessible by both WinXP and Linux.
Has anyone out there ever tried anything remotely like this?
Thanks!

I assume this Highpoint has it's own RAID-BIOS?
If it does, you could be in trouble, the K8T-Master isn't very happy with controllers that use 2 instances of a controller.
I have tried to get a lot of SCSI Raid controllers working, but no luck, they are the same pricipe.
I tested:
Ami MegaRaid 1600 Elite, windows saw it, but wasn't useable.
Adaptec (forgot the model very old one), board refused to even boot.
IBM Raid (very old as well) would boot, drivers would not install.
Several other have seen the same problems, it has to do with the INT19 (software IRQ) where the controller needs to hook into.
(At least I came to that conclusion)
It doesn't hook into that, but the controller does show up, but can't use the RAID-Processor/BIOS for anything.
A normal SCSI controller like the Adaptec 2940 or such are no problem, but they only use 1 instance.
The difference between a RAID and Non raid controller is that the Non-Raid uses only 1 IRQ and Address, RAID (intelligent ones) use 2 IRQ's and 2 Addresses, and for some reason, the Mobo's BIOS doesn't want to hook both during boot.
In Windows the drivers will load, sometimes, but when you try to access it, Windows is not able to communicate with the Raid-CPU and all sorts of nast things happen, if you even get that far.

SATA RAID and K92A Platinum

OK Guy’s
I need your assistance here. I just purchased a MSI K92A Platinum motherboard and having the darnest time setting up RAID 0 (or any RAID period). Before I go any further this is my setup.
SATA 1 Western Digital WD2500JS 250GB SATA
SATA 2 Western Digital WD2500JS 250GB SATA
SATA 3 LITE-ON 20X DVD SATA MODEL LH-20A1S
SATA 4 Western Digital WD2500JS 250GB SATA
SATA 5
SATA 6
Floppy drive installed
Memory: Kingston Hyper 2GB 1066 (x2)
Processor: AMD 6400+ (3.2)
Video: Ge Force 8800 GTX
In the basic (CMOS) screen I see all my drives. When I move to the advance screen and select RAID. All the drives including my DVD disappear from the basic (CMOS) screen. In the RAID utility, I see all three hard drives (minus the DVD drive). I created my RAID 0 with two of the drives and left the last drive free for future use. The problem arises when I reboot and try to use my DVD drive with Windows VISTA. After the initial boot from the Windows CD, I followed the on screen instruction by selecting the install tab. It would prompt me for my license number and move to the next screen. After that it would return with the error unable to find DVD/CDROM (no further installation possible). Just remember it had booted off the CD in the first place. Not sure what is the problem. Unfortunately I can’t install WINDOWS on a RAID drive until I figure out why when I select RAID that my DVD is not seen correctly after booting .
All things being equal, I have no problem installing WINDOWS without defining a RAID device on this motherboard. All the drives are seen including my DVD. A little history I just came from using an ASUS MSN-SLI Deluxe motherboard and I did not have any of these problems. At this point is seems ASUS had the easiest RAID utility. Final note, hardware is good and tested. Any response would be greatly appreciated.
Thanks in advance
Richard

No, you can use as many as you would like. It's just that RAID 0 with three drives is not possible on the Promise controller (red ports), as it has only two ports. Therefore you will need to use the SB600 controller, which is somewhat picky about SATA RAID drivers...
Anyway, the Promise controller is already disabled. Set your SB600 controller to RAID in your BIOS, then enter the FastBuild utility using CTRL + F when prompted. Build the array to your likings and save the settings, then boot from your Vista DVD. If you're lucky the drivers from the MSI CD (for Vista) will work. Otherwise you will have to start trying SB600 SATA RAID drivers from other manufacturers, those from DFI are known to work quite well.

Confused about SATA RAID and SATA DVD

I'm planning to build a system based on the P965 Platinum board and I'm considering implementing a RAID 0 array. However, I have read of many problems with RAID and SATA DVD writers. Are most problems just due to BIOS problems or are there more inherent problems? Are people successfully running this board with a RAID array and SATA DVD? Can you boot from the SATA DVD drive?
If I have a pair of drives in a RAID array, can I add further hard drives that will not be in a RAID array? I won't trust RAID for all my data and I don't want to use mirroring.
I'm confused and I can't seem to find any definitive answers on this.
Thanks
Teresa

Quote
Thanks Maesus. Will the drive from an AHCI machine only work in another machine set up with AHCI?
Teresa, yes but not always, this AHCI is driver bound. And because this AHCI is driver bound, it makes it hard to change from IDE to AHCI for a IDE driver installed OS, as the OS doesn't have AHCI driver installed. So when you change to AHCI setting in the BIOS, the OS refuse to load further. AHCI is driver bound, and it is also controller/chipset bound. If you installed an OS with AHCI settings enabled in an AMD system, you may not run that in an AHCI Intel system. Vice versa.
Quote from: Teresa on 20-May-07, 19:51:36
I ask this because there's a thread here that gives instructions on how to turn on AHCI after Win XP has been installed. That tends to suggest that AHCI makes a difference to an operating system install.
This is only because the OS installer doesn't have AHCI driver built-in. If you slip-streamed your OS installer with AHCI drivers, your OS installation will go smoothly.
Quote
Or is it a case that the disk's data can still be read on another machine without AHCI but it can't be used to run Win XP? I just need to know that I can pull my data hard disk out of my system and access it on another older machine that doesn't have ACHI.
Yes, the disk's data still can be read anywhere else. Just that it cannot be used to boot up to WinXP, if that WinXP doesn't have AHCI driver installed.
Quote
Hopefully one day soon I'll reach a critical threshold of knowledge and actually start ordering the parts for my build.
Teresa
Let's make it simple. Treat IDE, AHCI and RAID-0 as different HDD drivers. WinXP has IDE driver built-in. Vista should have all drivers built-in. IDE and AHCI data structure is the same. However, RAID-0 data structure stored in the HDD is different and is controller-bound.
For AHCI mode installed HDD, you can read in IDE mode without single issue.
For IDE mode installed HDD, you can also read in AHCI mode without issue, provided AHCI drivers are installed upfront.
For RAID-0 installed HDD, you cannot read in IDE or AHCI mode, and you may not be able to read in other different controller/chipset systems even though you set them as RAID-0 exactly.

975X Platinum PowerUp 2*SATA/RAID and 1*IDE CDROM configuration help

I have latest official BIOS version 7.3
I’m trying to setting up the bios to handle 2 SATA harddisk in RADI 0+1. Furthermore I have IDE CDROM connected to the IDE1.
I have no problem setting up the 2 SATA harddisk as RAID 0+1 and it works perfect.
Unfortunately I don’t know how to setup the bios to make the IDE CDROM drive visible in windows.
Please help?
(I have tried to enable the JMicron, but then I can’t boot, because the mainboard loses the RAID controller. I have read that this has been a problem with BIOS version 7.2 and 7.3)
Regards,
Stigtk

Quote from: Jack the Newbie on 03-February-07, 07:58:12
Are you sure, that your are using IDE1? (blue slot)
Ups.. It was not the ’blue slot’. I have been using hours of solving this problem, and then it was so obvious.
Thanks.

Will SATA raid and MBP 2.16 Ghz ok for this....

I will be doing color correction of a 90 min film with 2 video tracks where the first track is the edited movie and second track, some Titles.
Usually, i upconvert the footage to 8 or 10 bit uncompressed format for color correction and final ouput.
I would like to try and takle this job with my MBP c2d 2.16 Ghz with a Sonnet SATA pluggeg into the expansion 34 card slot. Do all the work then bring the finished film to a post house for ouput.
Has anyone tried this and will such a set up powerful-stable enough to perform such a task without any problems ?? Thanks.

I will be doing color correction of a 90 min film with 2 video tracks where the first track is the edited movie and second track, some Titles.
Usually, i upconvert the footage to 8 or 10 bit uncompressed format for color correction and final ouput.
I would like to try and takle this job with my MBP c2d 2.16 Ghz with a Sonnet SATA pluggeg into the expansion 34 card slot. Do all the work then bring the finished film to a post house for ouput.
Has anyone tried this and will such a set up powerful-stable enough to perform such a task without any problems ?? Thanks.

SATA RAID conflics with POMISE T3 RAID Bios

I've read quite a few of the RAID setup issues concerning the "Extra" RAID settings under "integrated peripherals" for the K9A2 Platinum. My problem seems to be a bit unique. I can't get both the SATA RAID and the Promise "Fast Track" to work together. If I enable the Extra RAID Controllers the Fastrack Bios does not recognize my SATA RAID.
This simply means that for some reason the motherboard SATA RAID conflicts or disables the PROMISE RAID Bios and vice versa. So I have not been able to activate my eSATA ports or use anything connected to the SATA5-6 ports without going into the CMOS and setting SATA DEVICES to IDE and then turning on the EXTRA Raid Controller under "Integrated Peripherals" in the CMOS. Unless I'm wrong. I am almost sure that this scenario is right.
The second issue is that I cannot get my ram to go in DUAL CHANNEL mode. But I will post that issue another time.
thx
Please Advise.
Ami Bios v1.4
K9A2 Platinum MB, 790FX,
AMD 9850 Black Edition,
8GB GSkill RAM (800Mhz),
Samsung 500GB SATA11 (x4),
Radeon HD 3870 512 MB Video,
Rosewill 950Watt PSU,
Pioneer DVD RW,
NEC DVD RW,
9-in-1 USB Card Reader
2 ext (USB/eSATA) hard Drives (eSATA will not work because these ports are controlled by the PROMISE T3 Bios)

With Vista Ultimate SP1 on my machine the USB Flasher Tool kept on crashing when the BIOS was at v 1.2 on the KA92 mainboard.
The DOS window came up fine but it appeared that every susequent module that was brought up for detecting the motherboard caught some kind of conlfict and terminated causing Vista to summon the program terminated message box. Eventually the dos prompt would state that it could not detect the motherboard and close. All in red text. This happened only when I flashed the BIOS with v1.2. I wanted to go back to 1.3 just to verify that the BIOS version was the cause and the only reason I got back to 1.3 or 1.4 easily was becaus it was backed up by the tool so all I had to do was rename the backup.bin file(s). Again everything went as expected with the USB Flasher Tool until I loaded the v1.2 BIOS. It could not even detect the mainboard.
The only reason I didn't need the tool anymore was that it backed up the versions of the bios for each time that I had flashed the bios previously.
Ami Bios v1.2
K9A2 Platinum MB, 790FX,
AMD 9850 Black Edition,
8GB GSkill RAM (800Mhz),
Samsung 500GB SATA2 (x4),
Radeon HD 3870 512 MB Video,
Rosewill 950Watt PSU,
Pioneer DVD RW,
NEC DVD RW,
9-in-1 USB Card Reader

SATA RAID problem on K8N Neo2 Platinum (nForce3 ultra) & winXP x64

I entered on MSI driver dowload page, put my model, and i found out that the RAID driver for win x64 wasn't released (nforce3 ultra), but in the same page was the driver for the nforce4, so I supposed it was compatible. I made the driver disk. press F6 and he askme for the drivers, ok, i introduce BOTH drivers, he detects perefctly the SATA RAID (stripping) format the disk, copy the files and ask me for some .CATof teh raid driver that wasn't on the zip file.... omit files, reboots, completes the instalation, but on the first boot of win x64 when it's just about to show the windows screen, a bue windows, and resets the pc so fast that's unreadable. fail safe start.. same crash.
I Installed win on an IDE and it run prefectly... In th other hand... without installing any driver the windows instalation recognices the SATA drives, but not the RAID. Maybe I just got to install the raid driver but not the SATA driver... the nforce3 driver form nvidia.com is pretty old... The real funny is that when i installed winXp x64 BETA i hadn' any problem... (winXP 64 doesn't admit the 32 bit driver=
Which driver i'm supposed to install? to INSTALL winxp64 on a SATA RAID and make it boot from there?
Thaks a lot

HI! i'm the one wih the raid problem on a k8n neo2....
That's what a i Did.. i unpacked the exe and copy the files in a floppy... question is: if i do that, windows instaler askme for some files that aren't in the .exe, anway it reconices the raid and everithing goes fine until the first BOOT on windos... it shows a blue screen, butremoves it so fast that i cant read it or pause the system. But i know it's a raid problem because if i install it on a ide disk it works.
The nforce3 drivers are almost a year old, and i'm not sure if nforce4 is compatible...
I think the're compatible because if you enter in msi driver download page and select my model, they put the Nforce3 and nforce4 for win64 and my model is only nforce3. The thing is they havent released the nforce3 for WIN 64.... So.. It's normal that win asks me for some files that ain't in the .zip file (i extracted the files o course) and Which driver should i put the Nvidia one year old nforce3 or the new nforce4. (the nforce3 for 32 bits is rejected by windows) or... i have to wait the new nforce3?
thanks for helps

K9A2 Platinum Sata Raid Problems

I could not get my 2 500 gb seagate 7200.11 drives to work on the sb600 raid controller, in raid 1 (set to raid mode in bios). I'd set it up and it would remain functional until I formatted it and put stuff on it. Then when I restarted, it says critical and can't locate the second drive, but it shows up in the list of definable drives. My older 200 gb seagates 7200.9 in the same setup do not have this problem. I finally got my 500s working by hooking them up to the promise controller instead. (Although no longer a current problem, I wouldn't mind knowing what would cause this for future occasions.)
My new problem is, I had to unhook all but the drive I wanted to install Windows XP on (A separate 120 JBOD configured drive) so I could get it to be C:/. This all went fine. However when I hooked up the 500s again, Windows XP would not boot, the screen just stayed black, with them not hooked up, it boots just fine, with the 200s as well. When running the Windows XP setup again, the 500s appear as C:/ instead of the 120 in the disk select screen of the install. It's like the 500s took over the drive letter when they are hooked up and thus can't load. Is there some way to stop it from doing this or am I completely off on this.
My computer spec is:
K9A2 Platinum
AMD X2 6000
2*2gb OCZ PC6400
ATI Radeon 3870
700 Watt OCZ PSU
Update: Installing XP ignoring the fact its not C: fails. It copies all the files onto it, then after restarting I get a black screen.
Another Update: On a whim I tried disabling the SB600 raid and set it to AHCI instead as I read that other people were having problems with it and it all works perfectly now. It's too bad this doesn't work, but I'll just put the 200s back in my old computer instead.

I'm having the exact same problem you did. Same Mobo. Except I started off with Promise RAID 1 because when I tried using SB600 RAID, my SATA DVD drive would not function in Vista Ultimate x64. So I had my Raid 1 configured on Promise T3 with BIOS 2.8.1030.0021 using 2 320GB drives. One of them Seagate, one WD, both 3GB/s transfer, only difference was that Seagate has 16MB cache, while the WD has 8MB. But both drives worked fine in the array for some time, and then after doing some updates from Windows Updates now the Raid config shows that encountered a critial status, "A disk member of an array has failed or is not responding", "Problem is detected with Array : 1". And when I go to the see the Array status it shows the Seagate drive on ID channel 1, but for the 2nd drive it shows questions marks all the way through the item line. I checked the drive, it seems fine. And even when I go to define a second Array, it shows the WD available on channel ID 3. So it definitely see both drives, but how do I re-add that WD drive that it doesn't see to my earlier defined array without loosing data on my Seagate drive?

Unwanted SATA RAID

I've got a K8N Neo4 Platinum (non-sli) with the latest official bios (from live update)
My question:
Is it possible to disable the SATA RAID software that appears on boot. (The one wanting you to press [f4] or [ctrl + s] as it really adds alot of time to the boot proccess and is totally uneccesary with my one Ide drive ... lol

You should be able to disable it in the bios under integrated peripherals. Something like SATA controller.
Good Luck
Jeremy

Help! getting k8MM-V SATA RAID to allow Mode 0 (stripping)

Greetings all!
Help!
I can't get my motherboard's SATA utility to show RAID mode 0 (stripping)!
I only get choices for "Auto for security" and "RAID 1 (Mirror)."
I'm using the G72-VASA052 VIA SATA RAID Driver for VT6410/VT6420/VT8237 disk that came with the motherboard (I use this when I hit F6 for special drivers at Windows installation).
System:
K8MM-V motherboard
AMD Athlon 64 3000+
1 GB PC3200 (DDR400) SuperTalent ram (in 2 512 MB pieces)
2 Western-Digital 120 SATA drives (currently mirrored) :(
ATI Radeon 9800 Pro 128 (AGP)
I even ran the RAID MSI tool and the buttons for SPAN are greyed-out.
Any help here would be greatly appreciated...
Please post here or e-mail me at [email protected]
Thanks in advance,
- Sean Roberts

Thanks AGAIN for your help with this...
Yes, the manual is great for the physical things on this mobo... jumpers and pins... but it SUCKS for anything relating to the RAID controller. There is even a typo in the language of the RAID bios! It says that when creating a new raid, all data will be :"destriod" - bad translation, I guess.
You are saying that having existing partitions on one or more of the disks will PREVENT the SATA Raid bios from being able to choose RAID level 0?
I do remember that when I only had 1 WD 120 GB SATA drive that RAID was unavailable (requiring at least 2 disks). I got the second identical drive SPECIFICALLY to add in to create a RAID 0.
When I created my current RAID, the bios told me that everything on the disks would be destroyed.
How sure are you that existing partitions will prevent RAID level 0 from being shown as an option?
I ask because I will have to reload ALL my software to test this and do not want to do this unless you are SURE about your suggestion...
Thanks again, and I look forward to your reply.
Kind regards,
- Sean Roberts

Pt880 neo sata raid o corruption

i have a pt880 neo with a celeron d cpu 2 raptors in raid 0 using onboard raid .
runs great till i overclock , at 150 fsb raid array corrupts , using bios 1.5 .
any ideas ? maybe promise pci raid card or another mother board?.
what other motherboard chipset with on board raid will overclock.
i chose the celeron d as it is suppose to be a good overclocker 3.6 gig ?.
and i want to run the raptors in raid 0 for speed.
the pci card raid will be slower than onboard?.
thanks

I am using a celeron d based on the prescott , power supply is raidmax 420 watt.
i am certain that tha via sata raid controler can not handle the overclock it is not in the pci bridge and i don;t think it is or can be locked , used sata drives no raid same corruption at 150 fsb . when using pata drives no problems overclocks to 190 fsb today .
i want to use the raptors in raid 0 , so what m/b with onboard raid sata will work?
i don't want to change m/b only to have new one have same problem , also don't want pci raid runnig at 33mhz , whats the point , would like onboard raid that will allow overclock>?
thanks for everyone help
now help with selection of new motherboard.

915P Combo for SATA RAID

Okay, I just recently purchased a 915 P combo. I'm trying to setup a SATA raid and I don't have the option. The bios version is 1.2 and it's southbridge is a intel ICH6R. When I go into ATA/IDE configuration [Enhanced] I only see IDE and AHCI but no RAID. I have two 200gig WD hard drives. I don't know if this means anything either but the post screen says found primary master IDE drive and then says found secondary master ide drive. I'm not sure if it should say SATA or something else then IDE. Any help would be greatly appricated.

I purchased the 915P Combo from NewEgg.com which says:
"SATA/RAID: 4x SATA, 2x ATA(VT6410) 133 with RAID 0/1/0+1"
which led me to believe that it could do SATA RAID. My 915P box even says "SATA RAID - supports SATA and IDE interface RAID 0, 1 or 1.5". On the front of the box, like someone else mentioned, there is a big sticker that says "Intel ICH6/6R Test OK" which I can understand would not necessarily guarantee it had the 6R.
Looking closer at the sticker on the side of the mobo box it does say "P4-800, 915P, ICH6, ...." and not "ICH6R", but until reading this thread, I didn't even know what ICH6/ICH6R was, and wouldn't have helped me before purchase.
I think this is misleading and I'm pissed off- I purposely purchased two SATA 160gig drives when buying the parts for my new computer, soley to do RAID striping, and now I can't. I will be asking NewEgg for a refund and will likely not be buying another MSI product.
IF I were to purchase another MSI board, what SHOULD I get to have the SATA RAID features? (and will accept my P4-3GHz 800M LGA775 530, and DDR2)

Need SATA RAID driver for RS480M2-IL(ms-7093) to install XP

Greetings,
I have lost my floppy to install the driver for my SATA RAID and can't seem to find the right one anywhere on the web.
It's an ATI SB400 chipset that has a SIL 3112a RAID controller.
The driver doesn't appear to be on the support page: http://global.msi.com.tw/index.php?func=proddesc&maincat_no=1&prod_no=214
If anyone can point me in the right direction, you'd be my hero.
Thanks in advance,
Jeff

Well, I found the correct driver, I think. It was in the ATI System driver package, on this page: http://global.msi.com.tw/index.php?func=driverfile&dno=2427&i=1
However, I still can't get XP to recognize my drive by pressing F6 at install. Perhaps I'm not using the right files from this package (287MB!). I found what I thought might be the correct drivers in the following folder: ATIDrv/SBDrv/RAID4xx and copied all the files to a floppy. Windows sees this driver and loads it, but when it gets to the point of formatting a drive (or whatever the next step is after you hit F^ and load the driver), it says no HD found, hit F3 to restart (sure would be nice to have other options here, like load another driver).
So, here's more info about my system (read the posting guidelines since last time
mobo: RS480M2-IL BIOS 7093v39
PS:Thermaltake TR2-430NP
RAM: G.Skill PC3200 1GBx2
HD1:Seagate Barracuda 7200.10 160GB
HD2:Maxtor Diamondmax20 160GB
Problem started when co-worker shut the machine off hard. On reboot, Invalid System Disk error and looking at RAID Bios shows drives in SYNC state. Removed the drives and attached to another machine, one looks fine so I clone it for good measure. The other is corrupted, XP wants to format as soon as it's mounted. Checking it with Filescavenger3 shows the files are still there, but I just reformat it since I have the good image of the other disk. Now I'm trying to fix the other drive, since it still comes up as Invalid System Disk, so I want to try either using the Recovery Console to FixMBR, or do a repair install of XP. I can't find the right driver to make this happen. I do have a disk with LastXPv2.11 that will recognize the drive, but it doesn't allow me to get into the recovery console or offer to repair xp. If you know how to extract the drivers from a slipstreamed disc, that might work too. Finally, I don't know if I've update the RAID bios, or if that happens when you update the mobo bios. I did update that to v39 and the RAID BIOS shows 4.2.50.
Sorry this is so long, any ideas to help get me going here would be fantastic
Cheers,
Jeff

Neo2 BIOS 3.3 Disables VIA SATA Raid AND Promise IDE3 RESOLVED

Similar Messages

Maybe you are looking for