Neo2 Platinum discovery - BIOSes above 1.5 don't like internal IDE cards

I upgraded my BIOS tonight from 1.5 to 1.B only to discover my system wouldn't boot. I thought it was a problem with my SATA drive, so I disconnected all my other drives, and it worked. Because I was having several other problems with this BIOS, even when it was working, I downgraded to 1.9, but the same thing happened: with all my hard drives connected, my system wouldn't boot into Windows. After the DMI prefetch check, it just sat there like a lame goose. I disconnected my hard drives one by one to see which was the culprit, only to discover that the two drives connected to my Promise internal ATA100 IDE card were causing the problem. If those two drives were not connected, the machine booted normally, but when they were connected, the machine hung at start up.
I proceeded to try this for 1.8 and 1.7 with the same results. Only 1.5 seemed to work with my IDE card. I switched around PCI slots, turned off my ethernet slots (I was intermittently getting a Realtek ethernet jack error, which would also prevent me from loading up. This even happened in 1.5, but disabling that got rid of the problem. I use wireless anyway.)
Anyone know why this is the case? I suppose that it is not inherently PCI IDE cards that the BIOSes don't like, but the existence of hard drives on external channels. Because if I disconnect the hard drives from the card, there is no problem, and the OS boots normally.
I have heard of one other person in this forum having this problem, but I don't have the luxury of plugging my extra hard drives in internally.
Thanks in advance for the help/experience.

Quote
Thanks for that guide :-) Found it
Changing the agp voltage to 1.60 (From 1.50) had no effect
The Os is reused (working correctly on any other p.c), any time I try to clean install a new Windows Xp I get "Files not found" errors when it comes to installing any software it extracted to my drive
So far as I know the Nvidia Ide sw driver is not loaded, however it's one of those things I wouldn't know where to look to check pre-os
Chnaging to LBA from auto had no effect on my problem
All in all this has me stumped
(Edit: Congratulations on hitting the big 5000 posts )
Sorry nothing seems to work . I'm stumped too since you have had this rig running .
If you have warranty still valid perhaps you should have the board replaced .
Didn't notice I rounded the 5K

Similar Messages

Difference between K8N Neo2 Platinum & K8N Neo2-F

Can anyone help to clear up what exactly is the difference between these two motherboards? I have the features page printed out and compared them side by side, but I don't see any difference. I understand that the K8N Neo2 Platinum has been on the market for a while, and the K8N Neo2-F is new. Any help is much appreciated.
Here are the links to both of them:
http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo2_Platinum&class=mb
http://www.msicomputer.com/product/p_spec.asp?model=K8N_Neo2-F&class=mb

My Neo2 Platinum was the 54g version with a PCI 802.11b/g card and it seems that for some reason these boards have better power regulation than the standard Plat (at least the early models) as I have not had all the problems (PS/2, PCI, etc) some have had. And I have a Canon Digital Camcorder which only uses Firewire to output to PC.

PC Perspective #1 Leaderboard entry MSI K8N Neo2 Platinum nForce3 Ultra

PC Perspective...ala AMDMB.com has the top to rated pc builds using the MSI K8N Neo2 Platinum nForce3 Ultra.
Whooohooo
PC Perspective
I like Ryan's picks. By the way AMDMB does rock...fantastic forums great info on mobo's not just AMD either.

HI! i'm the one wih the raid problem on a k8n neo2....
That's what a i Did.. i unpacked the exe and copy the files in a floppy... question is: if i do that, windows instaler askme for some files that aren't in the .exe, anway it reconices the raid and everithing goes fine until the first BOOT on windos... it shows a blue screen, butremoves it so fast that i cant read it or pause the system. But i know it's a raid problem because if i install it on a ide disk it works.
The nforce3 drivers are almost a year old, and i'm not sure if nforce4 is compatible...
I think the're compatible because if you enter in msi driver download page and select my model, they put the Nforce3 and nforce4 for win64 and my model is only nforce3. The thing is they havent released the nforce3 for WIN 64.... So.. It's normal that win asks me for some files that ain't in the .zip file (i extracted the files o course) and Which driver should i put the Nvidia one year old nforce3 or the new nforce4. (the nforce3 for 32 bits is rejected by windows) or... i have to wait the new nforce3?
thanks for helps

Few question above the k8n neo2 platinum and raid

hi
i have for now intel 3.4ghz and asus p4c800dlux and 4 sata drives :
2x36giga wd 10000 raptors in raid 0 (connected to the on board promise sata controller)
2x200giga wd 7200 jd sata that (connected to on bard sata ports)
i order a athlon fx-55 and k8n neo2 platinum for a oc (a have 2x512 corsiar pc4000pro and hydro cool 200 ) and its look that its going to be problem
"SATA ports 1+2 will not maintain a lock and you can and will corrupt hard drives placed on these channels if you raise the HTT above 220mhz."
http://www.madshrimps.be/?action=ge...890&articID=228
so im in a problem, if i wont to do nice oc (and i will) i need to leave sata ports 1 and 2 not connected and buy a sata-pci controller for my 2x200giga , im right ?
in that case i need to connect the raptors in raid 0 in the sata 3-4 prots (near the agp) but:
the raid on the noe2 is "NV RAID (Software)" it means that there is no a controller like promise and the cpu need to replace the controller work, so its doing a lower performance.

If you had 4 huge drives I would be more sympathetic. To me every board is a compromise, resulting in me having to abandon something I might have done previoulsy. In you case ditch the two 36gb drives, and slum it with the 200gb drives. Remember that "overclocking" is not a right. There will be many users oblivious of the SATA 1/2 overclocking problems running 4 sata drives in RAID without a problem.

Help! My Neo2 Platinum freezes

hi all,
my system specs;
-AMD 64 3000+ with original fan (0451 FPGW)... No overclocked before
-MSI NEO2 Platinum with 1.5 bios
-Kingston 512MB DDR400 CL3 Ram
-Aopen KA50D case and its Aopen 300W PSU ( ı think it is produced by FSP)
-Xpert Vision 9550 ATI card... No overclocked before
-sound, lan onboard
-Toshiba 16X DVD-Rom, Lite-on 52x32x52 CDRW
this system freezes everytime when C'N'Q option was enabled in Bios and XP with SP1 ("minimum power management" was enabled) and also CoreCenter (1.7.3.0 version) was installed and C'n'Q was activated. first of all ı upgrade my board's bios from 1.4 to 1.5; and with 1.5 bios HT Frequency freezing problem is solved but this kind of freezing problem continues (XP freezing when in screensaver, any kind of game, and surfing in internet) no keyboard(PS2) and no mice(PS2) in action and also not any kind of erors in D-Bracket, all lights are green when freezing. How can I solve this issue? what's the problem I Don't understand. I tested ram 7-8 times in Memtest 86, no problem.
Bios also adjusted in optimized defaults.
Please Help this issue is beginning to drive me crazy
thanx for replies

As i'm in the PSU reply corner . I would suggest to use a more powerful one .
CnQ is putting a very special stress and demands on the PSU with powering , rise and risetime , fast/rapid wattage changes
and voltage drops/increase during this feature usage , and quite a lot of PSU's dont cope with this ultrafast load changes .
There is also some defualt timings in the A64 cpu that has to work in conjunction with the PSU to support
this feature .
It might just be that you are suffering from theese problems because of the PSU you have .
It does say : Power supply of 300 watts (and above) is highly recommended for system stability in the K8N manual .

Audigy 2 on Neo2 Platinum causes LOCK UPs/BSODs!!! Help!

I have a videocard with a HUGE, I mean HUGE custom CPU heatsink attached to it. This leaves me only ONE slot available for my Audigy 2. And that slot is the last slot 5, orange color.
Its the ONLY ONE AVAILABLE. I read on these forums about some incompatibility of Audigy 2 with MSI Neo2 Platinum. Thats what I have. I tried several later and older BIOSes including the official one and the latest beta one.
Still, when I play UT2004 or some other games that demand EAX/Hardware 3D sound - I get a dark blue BSOD without a message (its like a non-WinXP BSOD, its a hardware BSOD as I call it, dark blue color). It comes with a sqeeking sound. I have to restart my PC afterwards.
It happens after 3-4 minutes of playing.
When I REMOVE the soundcard - everything is fine, NO BSOD.
I tried different Audigy 2 drivers, but they all give the same result. This did not happen on my old ASUS A7N8X-Deluxe 2.0, and the soundcard was in PCI Slot 5 as well. I tried to format, and etc., - same thing if the soundcard is in the PCI slot!
I have PCI lock ENABLED (AGP set to 67Mhz, and PCI LOCK DETECTION set to ENABLED).
How do I fix this problem?

Quote
Originally posted by MonarchX
I have PCI lock ENABLED (AGP set to 67Mhz, and PCI LOCK DETECTION set to ENABLED).
When you said that you have PCI lock enabled and PCI lock detection enabled, were you talking about the same thing? If not, where in the BIOS is the PCI lock? I could only find PCI Lock Detection.

KN8 Neo2 Platinum Nightmare - please set me straight!

Hi,
Thank you very much for reading this post. Any help would be greatly appreciated, as i would like to avoid the RMA process
My problem: Intermittently, machine will not POST – (CD/DVD drives keep flashing/resetting forever)… no “beep”, and pc needs 4sec hold of power to shut down (don’t know if this gives any detail in sequence of post or not).
My Config:
K8N Neo2 Platinum
AMD Athlon 64 3500+
Corsair Dual (Twin) DDR 1GB PC3200XLPRO – in “Auto” originally, now in 2-2-2-5 with 2.75 volts
Antec TRUE POWER 450 (modular PSU)
2x Seagate 200MB HD in Raid 0 (stripe) (on SATA 0 and 1)
Floppy
Sony 4x DVD+/-R and LG 52x CDR on IDE 0
EVGA NVIDIA 6800GT 256
BIOS 1.2 (as shipped)
- NO Overclocking
Sequence of issue:
I built the machine last weekend and hooked everything up (I know a mistake) and machine would not post…. So I started unplugging, started with IDE-0 and it posts fine. So I think – ok so my issue is here….replace IDE cable and move drives to IDE 1 and I am fine. Installed windows…soft rebooted many times, fully installed my whole system, programs, drivers, etc. THEN – I did a HARD REBOOT. Problem comes back. I move CD Drives to IDE 0 and it boots fine again!.... Install games, play games for 5+ hours no problems.
Now I get this non-post issue every 3 hard boots or so. First boot after the problem, bios tells me I have a failed OVERCLOCK, adjust in setup…which is BS but I have to go to bios settings, change nothing, then it boots fine.
One other thing – the memory is supposed to be a 2.75 volts according to Corsair, so I changed that (bios seting is RED – not recommended) and this change does not seem to affect anything (can post and operate normally for a while then get no post again).
I have built 10+ systems and this is the most frustrating issue ever for me!!! My guess was:
1) loose connection – nope – reset everything 3x
2) Power – tried using different power connectors for 6800GT card but don’t know if there are any specific issues here (maybe the card needs a connector with nothing else on it?)
3) RAM / CPU / MB issue: I have tried moving ram in slot 2/3 but same issues. I reeeeely don’t want to have to re-seat the athlon64.
THANKS FOR ANY/ALL INPUT !!!!!!!!!!!!!!!!!!!!!!!

And here's an important thing to read :
It's comming from an article at ModdersHQ community"
Quote
The Noisetaker probably performed the weakest out of all 3 in the test. However, considering this PSU is only rated at 470w, compared to 510w and 550w; and it does not have adjustable rails, it did very well. The rails were all well within reason, but the Noisetaker showed the largest drop, especially on the 12v rail. I think the 6800 Ultra was beginning to suck more juice than the Noisetaker had. Unfortunately, here is where you can see the downside of dual 12v rails: there is no "backup" or "reserve" current.
Each 12v rail has about 15 amps of current, compared to the usual 34 amps or so on a normal PSU. Now, if you add them together, everything is fine. But the problem arises when you suck too much current from a single rail. With a regular PSU, the current ceiling is very high(30a or so), so even though you might be running a ton of fans and drives, chances are you can at least unplug something if the rail drops too low. Also, if you have less fans and drives, then you have more current at your disposal. However, if you are only working with a 15a current, then your ceiling is much lower. You have no "reserve" current to draw from that would be designed for fans and drives. So even if you have a single drive and fan plugged in, you still only have 15a for your motherboard, CPU and graphics card. And there is no way to access that other 12v rail without running a molex from the second rail. That is most likely why you see the dip in the 12v rail from idle to load. Although not huge, it is noticable, and with a smaller PSU would become a problem.
That can explain our problems...!!!

Need help with k8n neo2 platinum

I've just installed a new k8n neo2 platinum s939 board with a venice core 3200+ cpu the htt is 2000 and multiplier 10x.
I've gone to the core cell menu and set the htt to 4x (seemed to be this at default) and the max mem clock at 166 (more about this in a moment), the fsb will go quite easily up to 250mhz even 255mhz, but when I try 260 Mhz the machine when it reboots shows the initial slash screen but then goes to a blank screen with the cursor flashing in the top left hand corner, I can't even get back into the bios setup without clearing the cmos.
The odd thing is that the adjust cpu vid is showing a voltage of 1.50 and not 1.40 or startup.
Anyway with the fsb at 250mhz the bios screen is showing the Current ddr clock at 208 mhz ( not the max memclock setting of 166) the memory in the motherboard ( a crucial 512meg ddr333 single stick) seems to perform OK according to memtest which shows no errors after 2 cycles.
Any attempt to get to 260mhz fsb appears to fail even by upping the cpu vid to 1.525v unless i adjust the cpu voltage setting which by default is set to (by cpu vid) to +3.3%. Doing this enables me to get to fsb 260mhz but the memtest fails ( even when I set the max memclock to 133, which shows my current ddr speed at 174mhz, well below the 208mhz which appeared stable with the fsb at 250mhz?)
So firstly why are there two cpu voltage settings in the bios when my manual only shows 1 (there is no mention of this cpu vid setting?
How is it that my memory is stable at 208mhz with a fsb of 255mhz but unstable at 174mhz with the fsb set at 260mhz?
Why does the memory clock lock not appear to be working, the memory should be fixed at 166mhz but infact increases with fsb?
I have bios revision 1.5.
Please help as I am not familiar with the bios settings for this nforce 3 chipset, they seem rather odd to me. I'm sure my venice core 3200+ cpu can get beyond 250mhz fsb, I have another pc with a venice core 3000+ cpu which runs quite happily at 270mhz fsb.
PS I've tried reducing the htt to 3x but the same thing happens.

OK further feed back, I can get to over 260mhz fsb but the system is not stable the memory runs OK with mem test but I have problems with prime95.
I had to up the cpu core voltage to 1.53v to get to 260mhz using the cpu voltage setting in the bios and setting a 5% increase. increasing the cpu vid setting to 1.55v did not seem to do anything at all the core voltage was still at 1.43v.
I upped the mem voltage to 2.6v from 2.5 but still could not get the system to be stable, it may be that the memory is holding the system back but I don't want to pay for better memory at the moment. Unless anyone has got any other ideas it looks like I may be forced to settle with 250mhz, well still a 500mhz increase maybe not that bad. I've now to try 3d benchmarking using my radeon 9600xt and 3dmark 03.

Neo2 Platinum and AMD X2 ??

I am currently running an Athlon64 3500 in my Neo2 Platinum with
BIOS v1.4.
I want to upgrade my CPU to an Athlon 64 X2 3800 Dual-Core
Will i have to upgrade my BIOS ?
I`m running Windows XP Home. Can i easily flash the
BIOS using Live Update ?
I`ve done BIOS flashes before in the past with a floppy drive.
But now, i no longer have a floppy in my system.
I guess i could borrow one from someone if i really had too !!
I just downloaded and installed Live Update from the MSI web site.
How reliable is it to flash the BIOS with it ??

Quote from: dirtspin on 24-December-05, 09:06:00
I just downloaded and installed Live Update from the MSI web site.
How reliable is it to flash the BIOS with it ??
Noooo! Stop!
Live Update is the absolute best way to guarantee a BAD BIOS flash!
Download & install your BIOS file manually via floppy and flashing utiliy - it's the most reliable way
That being said... You will have to upgrade your BIOS and reinstall XP to make sure it uses both cores effectively. Sounds like a pain, but it's worth it.

Neo2 platinum Encountering Stability Problems /w dual channel memory

Hello,
Recently I built my first computer ever, see bottom. After getting windows installed I then had problems with installing other programs and general stability issues. I tried reinstalling windows and after the reinstall I got the same problems.
Something to do with the instability is when I start it up, and go into BIOS, it states my Athlon 64 3500+ as running at 2211, a half percent overclock. Also, even though I have the FSB set as 200mhz, when I go into CoreCenter on windows it states the FSB as being set 201mhz. In the nVidia system utility, it states my memory as running at 402mhz, and I had to crank that down to 400mhz to get stability, it allowed my to install programs without error, but there were still stability problems like crashes(blue screen, the computer just plain restarting without notice). I took out one of my memory cards, both of them work alone though, I've ran memory test utilities. That had a good effect and the computer runs fairly stable, but I still have problems, and I want to be able to take advantage of dual channel. I'm running my memory on auto and it's using the times of 2-3-3-6-2T.
Another problem I'm experiencing is the AC97 audio not being detected and loaded by windows, it will say I have no audio device, and the speaker will not show up in the notification area in the bottom right-hand corner. This happens inconsistantly.
-Thank You
AMD Athlon 64 3500+
MSI Neo2 Platinum(nForce3 939 socket)rev1.0 BIOS 1.4
2x Mushkin DDR400 512mb CL2 Blue
BFG GeForce6800GT OC
80gb Hitachi Deskstar SATA

hi bknoll,
welcome to the forum.
1) i wouldn't worry overmuch at the 201 issue.
2) Quote
I've ran memory test utilities. That had a good effect and the computer runs fairly stable, but I still have problems
which test utilities did you use, Don't quiet understand Quote
had a good effect and the computer runs fairly stable
3) It may be worth checking the Mushkin site or any documentation you have to verify that the auto settings agree with the quoted settings for the modules. It's not unkown for errors to occur when the memory controller on the CPU to misinterpret the SPD chip setting on your sticks - this is where the auto settings come from. Some memory like certain corsair modules need to run at different settings on AMD64, thus auto timings must be overidden,
4) Have you installed the Realtek drivers from the CD, & enabled onboard sound in Bios. When these are done normally there's the MSI Sound Effect manager in control panel. you just need to set your speaker config in the Windows Sounds & Audio Devices.
5) Usual question What power supply are you using as been underpowered on the 12v rail in particular can be the cause of crashes,

K8N Neo2 Platinum Ordered - Advice for a noob please

Hi there,
this seems like a great forum, was hoping someone could give me some advice - Im trying to pre-empt any major probs....
I am a relative noob to building P.C's - done a few P4 based systems before but this will be my first Athlon based. This systems primary use will be gaming. I have the following on order (should be with me next week) : -
a) MSI K8N NEO2 Platinum Edition SCK 939 Motherboad
b) AMD ATHLON 64 3500+ 64bit SCK 939 Retail Inc Fan
c) 160GB Maxtor Calypso 8mb Cache 7200 SATA DHH
Components I have already
a) Graphics Card - Nvidia 6800 GT
b) Memory - Generic 2 X 512MB PC2700 DDR333 RAM
c) Sound Card - Creative SB Live Value
d) PSU - Jeantech 450W (22a on 12V Rail)
e) Case - pretty generic full tower case - no fans attached
f) CPU FAN - COOLERMASTER HYPER 48 SUPER SILENT HEATPIPE
g) Spare Hard drive - 120GB Maxtor IDE Hard drive
h) DVD Drives - 1 x Pioneeer 108 / 1 x Pioneer 104
I) Monitors - Ilyama 17" TFT & Toshiba 32WL36P LCD
I have some 'noobish' questions - apologies for my ignorance : -
1) Memory - Will my memory be okay ? Should I ditch it and buy some Corsair DDR400 (which everyone else seems to have!). Will performance suffer if I stick with the DDR 333 ? Do I need to adjust settings in BIOS regarding memory timing ? (I only picked up on this from reading through other posts on this board, and am totally clueless on 'timing'- Ive never needed to adjust timing on any previous PC's....!)
2) Sound Card - will I be better off sticking with the onboard sound on the MSI K8N neo 2 ? Or for best performance do I go with the SB LIve ? (god its a nightmare trying to get updated drivers for this card), Would I get a noticable performance increase buying an Audigy 2?
3) Vcore / other power issues - Reading this forum Im kinda scared by many posts along the lines of "..for stability I need to change my memory voltage to xx-V" or "...for a stable system I needed to change my Vcore to xx-V". Will I need to change the Bios default values on this system just to get it to run stably??
4) CPU FAN - Are AMD stock fans any good ? My Hyper 48 is quite highly rated....
5) Im completely new to SATA drives, but Ive printed off the very useful install guide on this site (which I intend to use). Is there anything I need to look out for concerning adding my IDE drive also.
I think thats about it just now - if anyone can see any other potential problems with my specs then please let me know. Im really not trying to be negative / pessimistic - after all the reason I have went for this motherboard is that it is rated as one of the best. Im just a bit paranoid that the dreaded B.S.O.D awaits me!
On a more positive note - does anyone have similar system specs they use for gaming ? How well does HL2 / Doom3 / Farcry etc fly J ? I cant wait !
Thanks for the time

you may find these helpful
Overclockers Uk Power Supplies
This Week Only Enermax Noisetaker 485W EG495AX-VE(G) SFMA ATX2.0 PSU (CA-007-EN) Might be tempting
Scan International Power Supply

SATA HDD installation on K8N Neo2 Platinum, Non-RAID, Non-Bootable

Hi-
I’m a rank newbie on this forum (first post). I have a K8N Neo2 Platinum Mobo, which I’ve recently gotten up and running, with Windows XP-Pro SP2 installed on a single IDE drive. I would now like to add 2 SATA drives. I don’t need or want the SATA drives to operate in a RAID array, nor do I want them to be bootable. I want to use them independently for data storage. I read the following thread (I am posting here on a separate thread per the author’s wishes not to get his original thread too junked-up) :
Single SATA or Multiple Drive Array Setup FAQ
I have not yet plugged-in either of my SATA drives, because I don’t want to risk corrupting my existing boot (IDE) drive. I just had a few questions about the procedure given in the referenced thread, in the Single Drive Setup:
- Step 14 States: “Make sure the “RAID Mode” is Stripping and Striping Block at 64k or Optimal. Hit F7 (Finish)”. Is this correct for a single non-boot drive?
- Step 22 States: “As most of you know when you enter the Setup for Win2k/WinXP you will need to hit F6 to load additional drivers for other SCSI devices.” I assume this means I need to boot from the Windows CD. Is this true even if I already have Windows installed on an IDE HDD on this system? At what point will I need to hit <F6> ? Will I be prompted to do so?
- I have downloaded (from the MSI website) the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total). Should I put these on a floppy? Or can I access them from a directory on my OS HDD?
- Should I go ahead and plug-in both of the 2 SATA drives I want to add to the system before beginning the driver installation? The only reason I would consider installing them one at a time is if it eliminated any confusion between RAID vs. independent (I want independent operation). If I do install them one at a time, do I have to install the driver twice?
Any help would be appreciated.
- the bbdude

OK Thanks JeanGuy and ssjkakaroto,
I have connected both of my SATA drives. They are enabled in BIOS but not set to RAID. I booted up to Windows on my IDE drive. In Disk Manager, the display shows Disk 0 (C: System), Disk 1 and Disk 2 as uninitialized, and my DVD (D:) drive. At this point, I could probably go ahead and run the Initialize and Convert Disk Wizard to get these disks formatted and be dome with ot now. Before I do that though, I just have a couple of more questions.
- I had already loaded the nVidia nForce3 system driver prior to installing the SATA drives, but I went ahead and did that again after installing the SATA drives and restarting Windows. I used Live Update, which went out to the MSI site and found version 5.03 of the nVidia nForce3 system driver. I'm not sure how to find the "Nvidia 5.10 driver package which include the latest SATA driver", ssjkakaroto referred-to. The Live Update install procedure did ask if I wanted to install IDE driver and I said yes. It then asked to over-write what I already had there (I said yes to that too). As the file names streamed-by, I though I saw some filenames with nv... listed. So, bottom line, is I'm not sure if I have the lates and greatest nVidia SATA drivers installed. How can I find out what drivers are installed?
- As I mentioned in my previous post, I have also downloaded and unzipped the NVIDIA RAID CLASS DRIVER & NVIDIA Nforce Storage Controller (20 files, 1.3 MB total) from the MSI site; however, I don't know how to "install" this now that I have the files. There are a couple of .exe and a .bat file (bit no setup.exe).
I may already have everything I need to partition and format these drives. I just want to bve sure I'm not skipping a step that is essential to optimal performance.
Thanks -
- bbdude

MSI neo2 platinum problem, forced to reset BIOS everytime I turn on the PSU

I just got my neo2 platinum mobo. Everytime I switch it ON all the led's at the back (diagnostic) turn red/orange and never turn green.
I have to reset the bios everytime to get it to post successfully. (bios is the original bios, no flashes done)
Processor: 3000+ (939)
Anyone else have this problem? what causes it?
[update] the bios version is 1.3 which is the latest on the msi website
System Specs..
AMD Athlon 64 3000+ 90nm (socket 939)
MSI K8N Neo2 Platinum
1 GB Kingston HyperX DDR 400 CS2
SBlive
Nvidia GeForce4 Ti4200 128MB MEM
Logitech MX510
1x80GB WD HDD with 8MB cache
1x120GB WD HDD with 8MB cache
Lite-On 48x CD-RW
NEC 16X DVD RW Drive
RAIDMAX Black Aluminum Gaming Case with 6 case fans and 420W PSU

I think the power supply may be the problem
Once you reset the bios you don't need the amps to spin up the drives, as they are already spinning, saving you about 3 amps I bet. If the newer bios doesn't help, try unplugging half those case fans, the non boot drive, and take the cd's out of you optical drives so they dont spin up, then try cold booting your box a couple times. If it works you know you need a new power supply.
If it doesn't perhaps you've got a grounding problem? Are you positive that nothing metal is touching your motherboard where it shouldn't? If that isn't it, Id assume the cmos never really clears, and then take the battery out of the motherboard for a good hour while the power supply is unplugged, then give it another shot. I've seen a bunch of DFI boards do weird stuff like that before, the exact same thing actually. Nvidia has a few odd issues with the nforce chipsets and the cmos.
Oh, since you asked, 3000+ is 1.8 ghz. It will probably run at 2.4ghz easy (1.4 volts), thats a 90nm chip

New/modified voltage.ini for MBM5 5.3.7.0 to fully support K8N Neo2 Platinum

I have been fed up with the misread of MBM5 with Neo2 since i made the switch from Neo1
Fixed :
vcore fixed calibration
+3.3v fixed (showed to low level)
+5v calibrated
+12v fixed ( showed to high level)
New section to select Neo2 Platinum as the voltage configuration .
Here's the whole voltage.ini file in the code box .
Just save the previous one as voltage.ini.bak and paste this in a new file , restart MBM .
Code: [Select]
/* Voltage file for MBM */
/* Dated: 18-Jun-2004 08:41:37 */
/* [name] = sensorchip name -exactly- as in chipinfo.ini */
/* VT = number of voltage configurations start at 0 */
/* Vx = where x is voltage config number */
/* this holds the name of voltage config */
/* VxVy = where x is the voltage config number */
/* where y is the voltage number default this is */
/* 1 core 0 */
/* 2 core 1 or 1.5 or 2.5 */
/* 3 3.3 */
/* 4 5 */
/* 5 12 */
/* 6 -12 */
/* 7 -5 */
/* this holds the register and calculation for */
/* the voltage in question */
/* As of MBM 5.3.0.0 you can use a total of 16 */
/* calculation, if for example you want sensor */
/* to show a voltage that MBM does not show */
/* right now then add an 8th line, place your */
/* code in there and set MBM voltage sensor 8 */
/* to MBM Fixed */
/* 255 = should always be used if a voltage is not */
/* supported by this voltage config selection */
/* $xx = a register from the sensor chip, any $xx */
/* value in the string will be replaced with */
/* the value from that register of the sensor */
/* chip */
/* B = option to use bank switch on ISA based */
/* sensor chips, always use at end and always */
/* followed by a bank number in hexadecimal */
/* | = needed on dual sensor chips, always use it, */
/* followed by 0 or 1 for the 1st or 2nd sensor */
/* chip found */
/* - = a calculation with a negative number is only */
/* possible if that number is between ( ) */
/* example: $12*(-0.4) will work */
/* $12*-0.4 will NOT work */
/* // = remarks, don't use anything else */
/* . = in ALL calculation use a dot as the decimal */
/* symbol, even if it's not your normal decimal */
/* symbol. */
/* if you feel you have a new voltage configuration for */
/* your board then feel free to send it to support at */
/* [email protected] */
[None]
VT=0
V0=None
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[National LM78]
VT=2
V0=LM78 Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=$25*(-0.016)*3.47
V0V7=$26*(-0.016)*1.5
V1=LM78 Epox
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*4
V1V6=$25*(-0.016)*4
V1V7=$26*(-0.016)*1.666
V2=LM78 Tekram
V2V1=$20*0.016
V2V2=$21*0.016
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016*3.8
V2V6=$25*(-0.016)*3.94
V2V7=$26*(-0.016)*1.5
[National LM78j]
VT=2
V0=LM78j Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=$25*(-0.016)*3.47
V0V7=$26*(-0.016)*1.5
V1=LM78j Epox
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*4
V1V6=$25*(-0.016)*4
V1V7=$26*(-0.016)*1.666
V2=LM78j Tekram
V2V1=$20*0.016
V2V2=$21*0.016
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016*3.8
V2V6=$25*(-0.016)*3.94
V2V7=$26*(-0.016)*1.5
[National LM79]
VT=2
V0=LM79 Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=$25*(-0.016)*3.47
V0V7=$26*(-0.016)*1.5
V1=LM79 Epox
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*4
V1V6=$25*(-0.016)*4
V1V7=$26*(-0.016)*1.666
V2=LM79 Tekram
V2V1=$20*0.016
V2V2=$21*0.016
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016*3.8
V2V6=$25*(-0.016)*3.94
V2V7=$26*(-0.016)*1.5
[Winbond W83781D]
VT=0
V0=W83781D Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=$25*(-0.016)*3.47
V0V7=$26*(-0.016)*1.5
[Winbond W83782D]
VT=1
V0=W83782D Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=(($25*0.016)-3.6)*5.14+3.6
V0V7=(($26*0.016)-3.6)*3.14+3.6
V1=W83782D Abit BP6
V1V1=$20*0.016
V1V2=$21*0.016B$05
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*3.8
V1V6=(($25*0.016)-3.6)*5.14+3.6
V1V7=(($26*0.016)-3.6)*3.14+3.6
[Winbond W83783S]
VT=3
V0=W83783S Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=(($25*0.016)-3.6)*5.14+3.6
V0V7=255
V1=W83783S Soyo 7IZB+
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*3.8
V1V6=(($25*0.016)-3.6)*5.14+3.6
V1V7=(($26*0.016)-3.6)*3.14+3.6
V2=W83783S K7NCR18D/G
V2V1=$20*0.016
V2V2=$21*0.016
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016
V2V6=$25*0.016
V2v7=255
V3=W83783S Tekram P6BX-A
V3V1=$20*0.016
V3V2=$21*0.016
V3V3=$22*0.016
V3V4=$23*0.016*1.68
V3V5=$24*0.016*3.8
V3V6=(($25*0.016)-3.6)*5.14+3.6
V3V7=(($26*0.016)-3.6)*3.14+3.6
[Genesys Logic GL518SM]
VT=0
V0=GL518SM Standard
V0V1=($0D+2) * (2.38/128)
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[Genesys Logic GL520SM]
VT=0
V0=GL520SM Standard
V0V1=($0D-0.18) * (2.43/128)
V0V2=($14-0.18) * (2.43/128)
V0V3=($15+3) * 2.5 * (2.43/256)
V0V4=($13-0.18) * (2.43/128)*4.191489
V0V5=255
V0V6=255
V0V7=255
[Analog Devices ADM9240]
VT=0
V0=ADM9240 Standard
V0V1=$21*0.014
V0V2=$25*0.014
V0V3=$22*0.0172
V0V4=$23*0.026
V0V5=$24*0.062
V0V6=((($25*0.014)-(5+(5-($23*0.026)))) * 2.879-(5+(5-($23*0.026))))
V0V7=255
[National LM80]
VT=2
V0=LM80 Standard 1
V0V1=$25*0.01392
V0V2=255
V0V3=$21*0.016431
V0V4=$23*0.025050
V0V5=$24*0.06
V0V6=$23*0.105476 - $20*0.052105
V0V7=255
V1=LM80 QDI BrillianX IS
V1V1=$23*0.014736842
V1V2=255
V1V3=$22*0.017366666
V1V4=$20*0.02632653
V1V5=$24*0.063156146
V1V6=$25*(-0.064432432)
V1V7=$26*(-0.027526881)
V2=LM80 QDI BrillianX I
V2V1=$23*0.014736842
V2V2=255
V2V3=$22*0.017366666
V2V4=$20*0.02632653
V2V5=$24*0.063156146
V2V6=$25*(-0.070114942)
V2V7=$26*(-0.027526881)
[Winbond W83627HF]
VT=11
V0=W83627HF Standard 1
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=(($25*0.016)-3.6)*5.14+3.6
V0V7=(($26*0.016)-3.6)*3.14+3.6
V1=W83627HF Standard 2
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*3.8
V1V6=(($25*0.016)-3.6)*5.14+3.6
V1V7=255
V2=W83627HF Standard 3
V2V1=$20*0.016
V2V2=$21*0.016
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016*3.8
V2V6=$25*(-0.016)*3.47
V2V7=$26*(-0.016)*1.5
V3=W83627HF Standard 4
V3V1=$20*0.016
V3V2=$21*0.016
V3V3=$22*0.016
V3V4=$23*0.016*1.68
V3V5=$24*0.016*3.8
V3V6=$25*(-0.016)
V3V7=$26*(-0.016)*1.5
V4=W83627HF Standard 5
V4V1=$20*0.016
V4V2=$21*0.016
V4V3=$22*0.016
V4V4=$23*0.016*1.68
V4V5=$24*0.016*3.8
V4V6=$25*0.016
V4V7=$26*0.016
V5=W83627HF Abit BE7/ KX7
V5V1=$20*0.016 // core
V5V2=$21*0.016 // ddr
V5V3=$22*0.016 // 3.3
V5V4=$23*0.016*1.68 // 5
V5V5=$24*0.016*3.8 // 12
V5V6=$25*0.016 // vtt
V5V7=$26*0.016 // vddq
V5V8=$51*0.016B5 // vbat
V5V9=$50*0.016*1.515B5 // 5vsb
V6=W83627HF Abit NF7
V6V1=$20*0.016 // CPU
V6V2=$21*0.016 // DDR
V6V3=$22*0.016 // +3.3V
V6V4=$23*0.016*1.68 // +5V
V6V5=$24*0.016*3.8 // +12V
V6V6=(($25*0.016)-3.6)*5.14+3.6 // -12V
V6V7=(($26*0.016)-3.6)*3.14+3.6 // -5V
V6V8=$50*0.016*1.515B5 // +5V Stand By
V6V9=$51*0.016B5 // +3.3V Dual
V7=W83627HF EPoX 8RDA3+
V7V1=$20*0.016 // MB (Vdd)
V7V2=$21*0.016 // CPU
V7V3=$22*0.016 // RAM
V7V4=$23*0.016*1.68 // +5V
V7V5=$24*0.016*3.8 // +12V
V7V6=$25*0.016 // AGP
V7V7=(($26*0.016)-3.6)*3.14+3.6 // -5V
V7V8=$50*0.016*1.515B5 // +5V Stand By
V7V9=$51*0.016B5 // +3.3V Dual
V8=Abit IC7/IC7-G
V8V1=$20*0.016 // core
V8V2=$21*0.016 // ddr
V8V3=$22*0.016 // 3.3
V8V4=$23*0.016*1.68 // 5
V8V5=$24*0.016*3.8 // 12
V8V6=$25*0.016 // vtt
V8V7=$26*0.016 // vddq
V8V8=$51*0.016B5 // vbat
V8V9=$50*0.016*1.515B5 // 5vsb
V9=W83627HF Aopen MX3S-T / MX3SP-T
V9V1=$20*0.016
V9V2=$21*0.016
V9V3=$22*0.016
V9V4=$23*0.016*1.68
V9V5=$24*0.016*3.8
V9V6=(($25*0.016)-3.6)*5.14+3.6
V9V7=$26*(-0.016)*1.5
V10=W83627HF EPoX 8RDA/8RDA+
V10V1=$20*0.016 // NorthBridge (Vdd)
V10V2=$21*0.016 // CPU
V10V3=$22*0.016 // DDR RAM
V10V4=$23*0.016*1.68 // +5V
V10V5=$24*0.016*3.8 // +12V
V10V6=(($25*0.016)-3.6)*5.14+3.6 // -12V
V10V7=(($26*0.016)-3.6)*3.14+3.6 // -5V
V10V8=$50*0.016*1.515B5 // +5V Stand By
V10V9=$51*0.016B5 // +3.2 V Battery
V11=W83627HF Standard 6
V11V1=$20*0.016
V11V2=$21*0.016
V11V3=$22*0.016
V11V4=$23*0.016*1.68
V11V5=$24*0.016*3.8
V11V6=(($25*0.016)-3.6)*5.14+3.6
V11V7=(($26*0.016)-3.6)*3.14+3.6
V11V8=$50*0.016*1.51B5 //5VSB
V11V9=$51*0.016B5 //VBAT
[Asus AS99127F]
VT=2
V0=AS99127F Standard 1
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=($25*(-0.016))*3.97
V0V7=($26*(-0.016))*1.503
V1=AS99127F Standard 2
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*3.8
V1V6=(($25*0.016)-3.6)*5.14+3.6
V1V7=(($26*0.016)-3.6)*3.14+3.6
V2=ASUS P4S533-E
V2V1=$20*0.016
V2V2=255
V2V3=$22*0.016
V2V4=$23*0.016*1.68
V2V5=$24*0.016*4
V2V6=255
V2V7=255
[Texas Instruments THMC50]
VT=0
V0=THMC50 Standard
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[FairChild FMS2701]
VT=0
V0=FMS2701
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[Sis SiS5595]
VT=0
V0=Sis 5595 Standard
V0V1=$20*0.016
V0V2=255
V0V3=$21*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=255
V0V7=255
[VIA Via686A]
VT=2
V0=VIA 686A Standard 1
V0V1=(($22*25 + 133)/2628)*1.25
V0V2=(($23*25 + 133)/2628)*1.25
V0V3=(($24*25 + 133)/2628)*1.67
V0V4=(($25*25 + 133)/2628)*2.6
V0V5=(($26*25 + 133)/2628)*6.3
V0V6=255
V0V7=255
V1=VIA 686A FIC SD-11
V1V1=(($22*25 + 133)/2628)*1.143
V1V2=(($23*25 + 133)/2628)*1.143
V1V3=(($24*25 + 133)/2628)*1.67
V1V4=(($25*25 + 133)/2628)*4
V1V5=(($26*25 + 133)/2628)*9.6
V1V6=255
V1V7=255
V2=VIA 686A Standard 2
V2V1=(($22*25 + 133)/2628)*1.21
V2V2=(($23*25 + 133)/2628)*1.25
V2V3=(($24*25 + 133)/2628)*1.67
V2V4=(($25*25 + 133)/2628)*2.6
V2V5=(($26*25 + 133)/2628)*6.3
V2V6=255
V2V7=255
[Winbond W83697HF]
VT=13
V0=W83697HF Standard 1
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=(($25*0.016)-3.6)*5.14+3.6
V0V7=(($26*0.016)-3.6)*3.14+3.6
V1=W83697HF Standard 2
V1V1=$20*0.016 // core
V1V2=$22*0.016 // agp
V1V3=$25*0.016 // 3.3
V1V4=$23*0.016*1.68 // 5
V1V5=$24*0.016*3.8 // 12
V1V6=$26*0.016 // vdimm
V1V7=255
V2=W83697HF Standard 3
V2V1=$20*0.016 // core
V2V2=$26*0.016 // agp
V2V3=$22*0.016 // 3.3
V2V4=$23*0.016*1.68 // 5
V2V5=$24*0.0643 // 12
V2V6=$25*0.016 // ddr
V2V7=255
V3=W83697HF Standard 4
V3V1=$20*0.016 // core
V3V2=$22*0.016 // 1.5
V3V3=$25*0.016 // 3.3
V3V4=$23*0.016*1.68 // 5
V3V5=$24*0.016*3.8 // 12
V3V6=$26*0.016 // vdimm
V3V7=255
V4=W83697HF Standard 5
V4V1=$20*0.016 // core
V4V2=$25*0.016 // agp
V4V3=$22*0.016 // 3.3
V4V4=$23*0.016*1.68 // 5
V4V5=$24*0.016*3.8 // 12
V4V6=$26*0.016 // vdimm
V4V7=255
V5=ABIT KX7 333
V5V1=$20*0.016
V5V2=$21*0.016
V5V3=$22*0.016
V5V4=$23*0.016*1.68
V5V5=$24*0.016*3.8
V5V6=($25*(-0.016)*5.14)+5.91
V5V7=($26*(-0.016)*3.14)+2.94
V6=AsRock K7VT2
V6V1=$20*0.016
V6V2=$21*0.016
V6V3=$22*0.016
V6V4=$23*0.016*1.68
V6V5=$24*0.016*3.8
V6V6=$25*(-0.016)*3.78 //V -12.00
V6V7=$26*(-0.016)*1.575 //V -5.00
V7=AsRock K7S8X
V7V1=$20*0.0164 // core
V7V2=255
V7V3=$22*0.0163 // 3.3
V7V4=$23*0.0164*1.68 // 5
V7V5=$24*0.0163*4 // 12
V7V6=255
V7V7=255
V8=Abit AT7 MAX
V8V1=$20*0.016 //VCORE
V8V2=$22*0.016 //VIO
V8V3=$23*0.016*1.68 //+5V
V8V4=$24*0.016*3.8 //+12V
V8V5=$25*0.016 //AGP
V8V6=$26*0.016 //DDR
V8V7=$50*0.016*1.51B5 //5VSB
V8V8=$51*0.016B5 //VBAT
V9=Asus P4SDX
V9V1=$20*0.0154
V9V2=$21*0.016
V9V3=$22*0.016
V9V4=$23*0.016*1.68
V9V5=$24*0.016*4
V9V6=255
V9V7=255
V10=W83697HF Standard 6
V10V1=$20*0.016
V10V2=$21*0.016
V10V3=$22*0.016
V10V4=$23*0.016*1.68
V10V5=$24*0.016*3.8
V10V6=(($25*0.016)-3.6)*5.14+3.6
V10V7=(($26*0.016)-3.6)*3.14+3.6
V10V8=$50*0.016*1.51B5 //5VSB
V10V9=$51*0.016B5 //VBAT
V11=W83697HF Epox 8K3A(+)
V11V1=$20*0.016 // Core
V11V2=$22*0.016 // AGP
V11V3=$26*0.016 // DIMM
V11V4=$25*0.016 // + 3.3
V11V5=$23*0.016*1.68 // + 5
V11V6=$24*0.016*3.8 // +12
V11V7=$50*0.016*1.68B5 // 5VSB
V11V8=$51*0.016B5 // VBAT
V12=Abit KD7
V12V1=$20*0.016 // Vcore
V12V2=$22*0.016 // Vagp
V12V3=$25*0.016 // +3.3
V12V4=$23*0.016*1.68 // +5
V12V5=$24*0.016*3.8 // +12
V12V6=$26*0.016 // Vdimm
V12V7=$51*0.016B5 // Vbat
V12V8=$50*0.016*1.515B5 // 5Vsb
V13=Cluster Labs CPU450
V13V1=$20*0.016 // Core
V13V2=$26*0.016 // RAM
V13V3=$22*0.016 // 3.3
V13V4=$23*0.016*1.69 // 5
V13V5=$24*0.016*3.8 // 12
V13V6=(($25*0.016)-3.6)*5.14+3.6 // -12
V13V7=$51*0.016B5 // Battery
[Analog Devices ADM1025]
VT=0
V0=ADM1025 Standard
V0V1=$21*0.012
V0V2=$20*0.013
V0V3=$22*0.0172
V0V4=$23*0.026
V0V5=$24*0.062
V0V6=((($25*0.014)-(5+(5-$23*0.026)) )* 2.879-(5+(5-$23*0.026)))
V0V7=255
[National LM87]
VT=1
V0=LM87 Standard 1
V0V1=$21*0.014
V0V2=255
V0V3=$22*0.017366666
V0V4=$23*0.016*1.632
V0V5=$24*0.016*3.9
V0V6=255
V0V7=255
V1=LM87 Standard 2
V1V1=$21*0.014
V1V2=$25*0.014
V1V3=$22*0.017366666
V1V4=$23*0.016*1.632
V1V5=$24*0.016*3.9
V1V6=255
V1V7=255
[VIA Via686B]
VT=3
V0=VIA 686B Standard
V0V1=(($22*25 + 133)/2628)*1.25
V0V2=(($23*25 + 133)/2628)*1.25
V0V3=(($24*25 + 133)/2628)*1.67
V0V4=(($25*25 + 133)/2628)*2.6
V0V5=(($26*25 + 133)/2628)*6.3
V0V6=255
V0V7=255
V1=VIA 686B ABIT VP6
V1V1=(($22*25 + 133)/2628)*1.24
V1V2=(($23*25 + 133)/2628)*1.25
V1V3=(($24*25 + 133)/2628)*1.665
V1V4=(($25*25 + 133)/2628)*2.54
V1V5=(($26*25 + 133)/2628)*6.4
V1V6=255
V1V7=255
V2=VIA 686B Asus A7VL-VM
V2V1=(($22*25 + 133)/2628)*1.88
V2V2=255
V2V3=(($24*25 + 133)/2628)*1.66
V2V4=(($25*25 + 133)/2628)*2.4
V2V5=(($26*25 + 133)/2628)*16
V2V6=255
V2V7=255
V3=VIA 686B MSI K7T Turbo
V3V1=(($22*25 + 133)/2628)*1.20
V3V2=255
V3V3=(($24*25 + 133)/2628)*1.67
V3V4=(($25*25 + 133)/2628)*2.6
V3V5=(($26*25 + 133)/2628)*6.3
V3V6=255
V3V7=255
[MySon MTP008]
VT=1
V0=MTP008 Standard 1
V0V1=$20*0.016 // cpu 0
V0V2=$23*0.016 // cpu 1
V0V3=$21*0.016 // 3.3
V0V4=$26*0.016 // 1.5
V0V5=$22*0.016*3.9 // 12
V0V6=255
V0V7=255
V1=MTP008 Standard 2
V1V1=$20*0.0158 // cpu 0
V1V2=$23*0.0158 // cpu 1
V1V3=$21*0.016 // 3.3
V1V4=$26*0.016*1.68 // 1.5
V1V5=$22*0.016*3.9 // 12
V1V6=255
V1V7=255
[National LM87 Dual]
VT=1
V0=LM87 Dual Standard
V0V1=$21*0.014|1 // cpu 0
V0V2=$25*0.014|0 // cpu 1
V0V3=$22*0.0017366666|0 // 3.3
V0V4=$23*0.016*1.632|1 // 5
V0V5=$24*0.016*3.9|1 // 12
V0V6=$25*0.014|0 // VTT
V0V7=255
V1=LM87 SM PIIIDME/370DE6
V1V1=$21*0.0136|0 // cpu 0
V1V2=$21*0.0136|1 // cpu 1
V1V3=$22*0.017366666|0 // 3.3
V1V4=$23*0.016*1.632|1 // 5
V1V5=$24*0.016*3.9|1 // 12
V1V6=255
V1V7=255
[ITE8712F]
VT=13
V0=ITE8712F Standard 1
V0V1=$20*0.01565
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$28*0.016 // vbat
V0V5=$24*0.016*3.8
V0V6=(($27*0.016)-3.6)*5.14+3.6
V0V7=255
V1=ITE8712F Standard 2
V1V1=$20*0.01614 // cpu 0
V1V2=$21*0.01614 // ??
V1V3=$22*0.01614 // 3.3
V1V4=$23*0.01614*1.68 // 5
V1V5=$24*0.01614*3.9 // 12
V1V6=255
V1V7=255
V2=ITE8712F Standard 3
V2V1=$25*0.01614 // cpu 0
V2V2=$21*0.016 // cpu 1
V2V3=$22*0.016 // 3.3
V2V4=$24*0.016 // 5
V2V5=$23*0.01614*3.9 // 12
V2V6=255
V2V7=255
V3=ITE8712F Standard 4
V3V1=$20*0.016 //V P4
V3V2=$21*0.016 //V AGP
V3V3=$22*0.016 //V +3.3
V3V4=$23*0.027 //V +5.00
V3V5=$24*0.06564 //V +12.00
V3V6=$25*0.016 + 4.25*($25*0.016 - 4.096) //V -12.00
V3V7=$26*0.016 + 2.20*($26*0.016 - 4.096) //V -5.00
V4=GA-8PE667
V4V1=$20*0.01653 //V VCore
V4V2=$21*0.016 //V 1.5 line
V4V3=$22*0.016 //V +3.3
V4V4=$23*0.02684 //V +5.00
V4V5=$24*0.06398 //V +12.00
V4V6=255
V4V7=255
V5=CT-7NJS
V5V1=$20*0.016 // CPU Core
V5V2=$21*0.016 // +2.5
V5V3=$22*0.016 // +3.3
V5V4=$23*0.027 // +5.00
V5V5=$24*0.06369 // +12.00
V5V6=(($25*0.016)+(-3.299555556))*5.142857143 // -12
V5V7=$26*0.016 // V_DDR
V5V8=$27*0.016 // V_AGP
V5V9=$28*0.016 // Battery
V6=GA-8IK1100
V6V1=$20*0.01565 // core
V6V2=$23*0.016 // 2.5
V6V3=$22*0.016 // 3.3
V6V4=$24*0.016*1.68 // 5
V6V5=$21*0.06564 // 12
V6V6=$25*0,016 // 1.5
V6V7=$27*0.016 // V_AGP
V7=Shuttle SB61G
V7V1=$20*0.016 // CPU Core
V7V2=$21*0.016 // +2.5
V7V3=$22*0.016 // +3.3
V7V4=$23*0.027 // +5.00
V7V5=$24*0.06369 // +12.00
V7V6=(($25*0.016)+(-3.299555556))*5.142857143 // -12
V7V7=$26*0.016 // V_DDR
V7V8=$27*0.026 // +5VSB
V7V9=$28*0.016 // Battery
V8=GA-8IPE1000Pro
V8V1=$20*0.01653 //V VCore
V8V2=$21*0.016 //V 2.5 line
V8V3=$22*0.016 //V +3.3
V8V4=$23*0.032 //V +5.00
V8V5=$24*0.064 //V +12.00
V8V6=$28*0.016 //V Battery
V8V7=255
V9=GA-8KNXP
V9V1=$20*0.016 // VCore CPU
V9V2=$21*0.01565 // VMem DRAM
V9V3=$22*0.016 // +3.3V
V9V4=$23*0.032 // +5.00V
V9V5=$24*0.064 // +12.00V
V9V6=(($25*0.016)-3.6)*5.72 // -12V
V9V7=(($26*0.016)-3.6)*2.33 // -5V
V10=Gigabyte GA-7N400-L
V10V1=$20*0.016 // V_core
V10V2=$21*0.016 // ram
V10V3=$22*0.016 // 3.3
V10V4=$23*0.016*2.00 // 5
V10V5=$24*0.016*4.00 // 12
V10V6=$25*0.016 // AGP
V10V7=$26*0.016 + 2.20*($26*0.016 - 4.096) // -5V?
V11=Asus A7V8X-X
V11V1=$20*0.016 // Vcore
V11V2=255
V11V3=$22*0.016 // +3.3
V11V4=$23*0.0265 // +5.00
V11V5=$24*0.0654 // +12.00
V11V6=255
V11V7=255
V12=GA-8PE667 Ultra
V12V1=$20*0.01653 //V VCore
V12V2=$21*0.016 //V 1.5 line
V12V3=$22*0.016 //V +3.3
V12V4=$23*0.02684 + .7 //V +5.00
V12V5=$24*0.06398 //V +12.00
V12V6=255
V12V7=255
V13=Elitegroup N2U400-A
V13V1=$20*0.016 // CPU Core by MBM
V13V2=$21*0.016 // Core 1 by MBM
V13V3=($22+500)/185 // +3.3V by Bulli; min. 2.7V ($=0), max. 4V ($=255)
V13V4=($23+400)/100 // +5V by Bulli; min. 4V ($=0), max. 6,5V ($=255)
V13V5=($24+1100)/100 // +12V by Bulli; min. 11V ($=0), max. 13,5V ($=255)
V13V6=-($25+1100)/100 // -12V by Bulli; min. -11V ($=0), max. -13,5V ($=255)
V13V7=-($26+400)/100
[ALi M5879]
VT=2
V0=ALi 5879 Standard 1
V0V1=$22*0.0161 // cpu 0
V0V2=255
V0V3=$20*0.0161 // 3.3
V0V4=$23*0.016*1.68 // 5
V0V5=$21*0.016*3.8 // 12
V0V6=255
V0V7=255
V1=Ali 5879 Standard 2
V1V1=$22*0.0161 // cpu 0
V1V2=255
V1V3=$20*0.0161 // 3.3
V1V4=$21*0.016*1.68 // 5
V1V5=$23*0.016*3.4 // 12
V1V6=255
V1V7=255
V2=Ali 5879 Standard 3
V2V1=$22*0.0161 // cpu 0
V2V2=255
V2V3=$20*0.0161 // 3.3
V2V4=$21*0.016*1.68 // 5
V2V5=$23*0.016*3.41 // 12
V2V6=255
V2V7=255
[Winbond W83L784R]
VT=0
V0=Winbond W83L784R Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=255
V0V6=255
V0V7=255
[Analog Devices ADM1024]
VT=0
V0=Analog Devices ADM1024 Standard
V0V1=$21*0.014
V0V2=$24*0.014
V0V3=$22*0.0172
V0V4=$23*0.026
V0V5=$25*0.062
V0V6=$20*0.013
V0V7=255
[Sis SiS5595 - rev 2.0]
VT=1
V0=Sis SiS5595 - rev 2.0 Standard 1
V0V1=$20*0.016
V0V2=255
V0V3=$21*0.016
V0V4=$22*0.016*1.68
V0V5=$23*0.016*3.8
V0V6=255
V0V7=255
V1=Sis SiS5595 - rev 2.0 Standard 2
V1V1=$22*0.016
V1V2=$23*0.016
V1V3=$21*0.016
V1V4=$20*0.016*1.68
V1V5=255
V1V6=255
V1V7=255
[Sis950 / ITE8705F]
VT=13
V0=Sis950 / ITE8705F -1
V0V1=$20*0.01614 // cpu 0
V0V2=$21*0.016 // 2.5
V0V3=$22*0.016 // 3.3
V0V4=$23*0.01614*1.68 // 5
V0V5=$24*0.01614*4 // 12
V0V6=$25*(-0.01614)*3.55 // -12
V0V7=255
V1=Sis950 / ITE8705F -2
V1V1=$20*0.01565 // cpu 0
V1V2=$21*0.016 // 2.5
V1V3=$22*0.016 // 3.3
V1V4=255
V1V5=$24*0.01614*3.9 // 12
V1V6=$27*(-0.01614)*3.47 // -12
V1V7=$28*(-0.016)*1.503 // -5
V2=Sis950 / ITE8705F -3
V2V1=$20*0.01614 // cpu 0
V2V2=$21*0.01614 // 2.5
V2V3=$22*0.01614 // 3.3
V2V4=$23*0.01614*1.68 // 5
V2V5=$24*0.01614*3.9 // 12
V2V6=$27*(-0.01614)*4 // -12
V2V7=255
V3=Sis950 / ITE8705F -4
V3V1=$20*0.01565 // cpu 0
V3V2=$21*0.016 // 2.5
V3V3=$22*0.016 // 3.3
V3V4=$23*0.016*1.68 // 5
V3V5=$24*0.016*3.9 // 12
V3V6=$27*(-0.016)*4.1 // -12
V3V7=$28*(-0.016)*1.65 // -5
V4=Sis950 / ITE8705F -5
V4V1=$20*0.01614 // cpu 0
V4V2=$21*0.01614 // 2.5
V4V3=$22*0.01614 // 3.3
V4V4=$23*0.01614*1.68 // 5
V4V5=$24*0.01614*3.96 // 12
V4V6=(($25*0.016)+(-3.299555556))*5.142857143
V4V7=(($26*0.016)+(-2.792727273))*3.142857143
V5=Sis950 / ITE8705F -6
V5V1=$20*0.01630 // cpu 0
V5V2=$21*0.01630 // 1.2
V5V3=$22*0.01630 // 3.3
V5V4=$23*0.01630*1.68 // 5
V5V5=$24*0.01630*3.96 // 12
V5V6=$25*0.01630 // ddr
V5V7=$26*0.01630 // agp
V6=Sis950 / ITE8705F -7
V6V1=$20*0.016 // cpu 0
V6V2=$24*0.016 // 2.5
V6V3=$21*0.016 // 3.3
V6V4=$22*0.016*1.68 // 5
V6V5=$23*0.016*3.96 // 12
V6V6=$25*0.016 // ddr
V6V7=$26*0.016 // agp
V7=SOYO DRAGON KT400 ULTRA PLATINUM
V7V1=$20*0.01614 // cpu 0
V7V2=$24*0.016 // 2.5
V7V3=$21*0.01614 // 3.3
V7V4=$22*0.016*1.69 // 5
V7V5=$23*0.01614*4.02 // 12
V7V6=$24*0.01614 // ddr
V7V7=$25*0.01614 // agp
V7V8=255
V8=ECS L7S7A2
V8V1=$20*0.01614 // cpu 0
V8V2=255
V8V3=$22*0.016 // ddr
V8V4=255
V8V5=255
V8V6=255
V8V7=255
V9=GA-8SQ800ULTRA
V9V1=$20*0.01614 // cpu 0
V9V2=$21*0.01614*1.300 // 2.5
V9V3=$22*0.01614*1.02 // 3.3
V9V4=$23*0.01614*1.68 // 5
V9V5=$24*0.01614*4.07 // 12
V9V6=(($25*0.016)+(-3.299555556))*5.16 //-12
V9V7=(($26*0.016)+(-2.792727273))*3.68 //-5
V9V8=$27*0.016 // DDR
V10=ECS L7S7A2
V10V1=$20*0.01614 // cpu core
V10V2=$21*0.016 // +2.5v (ddr)
V10V3=$22*0.016 // +3.3v
V10V4=$23*0.01614*1.68 // +5v
V10V5=$24*0.01614*4 // +12v
V10V6=$27*0.01614*1.68 // 5vsb
V10V7=$28*0.016 // vbat
V11=GA-8IK1100
V11V1=$20*0.01565 // core
V11V2=$22*0.016 // 3.3
V11V3=$24*0.0268 // 5
V11V4=$21*0.0736 // 12
V11V5=$27*0.016 // V_AGP
V12=Shuttle FX41
V12V1=$20*0.016016 // CPU VCore 1.75 (modified)
V12V2=$21*0.016 // VDDQ 3.3
V12V3=$22*0.016 // 3.3
V12V4=$23*0.016*1.68 // 5
V12V5=$24*0.016*3.9 // 12
V12V6=$27*(-0.016)*4.1 // -12
V12V7=$28*(-0.016)*2.463 // -5 (modified)
V13=SOYO KT400 DRAGON Lite
V13V1=$20*0.01614 // CPU core
V13V2=$24*0.01614 // DDR
V13V3=$21*0.01614 // +3.3
V13V4=$22*0.01614*1.663 // +5
V13V5=$23*0.01614*3.94 // +12
V13V6=$25*0.01614 // AGP
[Genesys Logic GL525SM]
VT=1
V0=GL525SM Standard 1
V0V1=$20+3 * (0.020078 * 1)
V0V2=255
V0V3=$22+3 * (0.020078 * 1)
V0V4=$23-3 * (0.020078 * 5/3.5)
V0V5=$24+3 * (0.020078 * (1.0+15.0/4.7))
V0V6=$25+3 * (0.020078 * (210/28))
V0V7=255
V1=GL525SM Standard 2
V1V1=$20+3 * (0.020078 * 1)
V1V2=$21+3 * (0.019 *1)
V1V3=$22+3 * (0.020078 * 1)
V1V4=$23-3 * (0.020078 * 5/3.5)
V1V5=$24+3 * (0.020078 * (1.0+15.0/4.7))
V1V6=$25+3 * (0.020078 * (210/28))
V1V7=255
[Analog Devices ADM1024 Dual]
VT=0
V0=ADM1024 Dual Standard
V0V1=$21*0.014|0 // core 0
V0V2=$21*0.014|1 // core 1
V0V3=$23*0.026|0 // 3.3
V0V4=$20*0.026|0 // 5
V0V5=$24*0.062|0 // 12
V0V6=$20*0.010|1 // 1.5
V0V7=255
[Dallas SM DS1780]
VT=0
V0=Dallas DS1780 Standard
V0V1=$21*0.014
V0V2=$20*0.013
V0V3=$22*0.017
V0V4=$23*0.026
V0V5=$24*0.0625
V0V6=$25*0.096 - 29
V0V7=255
[Analog Devices ADM1025 Dual]
VT=0
V0=ADM1025 Dual Standard
V0V1=$21*0.012|0 // core 0
V0V2=$21*0.012|1 // core 1
V0V3=$22*0.0172|0 // 3.3
V0V4=$23*0.026|0 // 5
V0V5=$24*0.062|0 // 12
V0V6=((($25*0.014)-(5+(5-$23*0.026)) )* 2.879-(5+(5-$23*0.026)))
V0V7=$20*0.013|1 // ??
[Dallas SM DS1780 Dual]
VT=2
V0=Dallas DS1780 Dual Standard 1
V0V1=$21*0.014|0 // core 0
V0V2=$20*0.013|0 // 2.5
V0V3=$22*0.017|0 // 3.3
V0V4=$23*0.026|0 // 5
V0V5=$24*0.0625|0 // 12
V0V6=$25*0.096-29|0
V0V7=255
V1=Dallas DS1780 Dual Standard 2
V1V1=$21*0.014|1 // core 0
V1V2=$20*0.013|1 // 2.5
V1V3=$22*0.017|1 // 3.3
V1V4=$23*0.026|1 // 5
V1V5=$24*0.0625|1 // 12
V1V6=$25*0.096-29|1
V1V7=255
V2=Dell PWS 420
V2V1=$21*0.014|0 // core 0
V2V2=$20*0.013|0 // 2.5
V2V3=$22*0.017|1 // 3.3
V2V4=$23*0.026|0 // 5
V2V5=$24*0.0625|0 // 12
V2V6=255
V2V7=255
[Analog Devices ADM1030]
VT=0
V0=ADM1030 Standard
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[Analog Devices ADM1031]
VT=0
V0=ADM1031 Standard
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[ITE8693F]
VT=0
V0=ITE8693F Standard
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.28
V0V5=$24*0.016*3.8
V0V6=$25*(-0.016)*5.2
V0V7=255
[PC87366]
VT=0
V0=PC87366 Standard
V0V1=255 // can't be done via ini file
V0V2=255 // can't be done via ini file
V0V3=255 // can't be done via ini file
V0V4=255 // can't be done via ini file
V0V5=255 // can't be done via ini file
V0V6=255 // can't be done via ini file
V0V7=255 // can't be done via ini file
[VIA Via8231]
VT=2
V0=VIA8231 Standard 1
V0V1=(($22*25 + 133)/2628)*1.25
V0V2=(($23*25 + 133)/2628)*1.25
V0V3=(($24*25 + 133)/2628)*1.67
V0V4=(($25*25 + 133)/2628)*2.6
V0V5=(($26*25 + 133)/2628)*6.3
V0V6=(($27*25 + 133)/2628)*2.6
V0V7=(($28*25 + 133)/2628)*6.3
V1=VIA8231 Standard 2
V1V1=(($24-3) * (2+10) / 10) / 95.8 // core 0
V1V2=(($23-3) * (2+10) / 10) / 95.8 // 2.5
V1V3=(($26-3) * (2+3) / 3) / 95.8 // 3.3
V1V4=(($22-3) * (14+10) / 10) / 95.8 // 5
V1V5=(($25-3) * (47+10) / 10) / 95.8 // 12
V1V6=255
V1V7=255
v2=EPIA Ezra
V2V1=(($24*25 + 133)/2628)*1.04 // core0
V2V2=(($23*25 + 133)/2628)*1.26 // 2.5
V2V3=(($22*25 + 133)/2628)*1.67 // 3.3
V2V4=(($25*25 + 133)/2628)*2.4 // 5
V2V5=(($26*25 + 133)/2628)*6 // 12
V2V6=255
V2V7=255
v3=EPIA Samuel 2
V3V1=(($24*25 + 133)/2628)*1.04 // core0
V3V2=(($23*25 + 133)/2628)*1.26 // 2.5
V3V3=(($22*25 + 133)/2628)*1.67 // 3.3
V3V4=(($25*25 + 133)/2628)*2.4 // 5
V3V5=(($26*25 + 133)/2628)*6 // 12
V3V6=255
V3V7=255
[Winbond W83627HF/W83782D Combo]
VT=1
V0=Standard W83627HF/W83782D
V0V1=$20*0.01614|0 // core 0
V0V2=$20*0.01614|1 // core 1
V0V3=$26*0.01614|1 // 3.3
V0V4=$23*0.01614*1.68|0 // 5
V0V5=$22*0.016*3.8|0 // 12
V0V6=(($25*0.016)-3.6)*5.14+3.6|0 // -12
V0V7=255
V1=Tyan Tiger MP 2460
V1V1=$20*0.01614|0 // core 0 (CPU 1)
V1V2=$21*0.01614|0 // core 1 (CPU 2)
V1V3=$22*0.01614|0 // +3.3 Volts
V1V4=$23*0.027205|1 // +5 Volts
V1V5=$24*0.075845|0 // +12 Volts
V1V6=$25*(-0.38375)|0 // -12 Volts
V1V7=255 // -5 Volts not implemented
V1V8=$22*0.01614|1 // AGP Volts
V1V9=$24*0.01614|1 // DDR Volts
V1V10=$26*0.01614|1 // standby 3.3 Volts
V1V11=$51*0.01614|1 B5 // battery Volts (on bank 5)
[SMSC LPC47M192-NC]
VT=1
V0=LPC47M192 Standard
V0V1=$21*0.012
V0V2=$20*0.013
V0V3=$22*0.0172
V0V4=$23*0.026
V0V5=$24*0.062
V0V6=$50*0.008
V0V7=$51*0.009
V1=Dell Precision 650
V1V1=$21*0.0114 // CPU voltage
V1V2=$20*0.013 // +2.5V
V1V3=$22*0.0171 // +3.3V
V1V4=$23*0.026 // +5V
V1V5=$24*0.06 // +12V
V1V6=$50*0.0171 // SIO voltage
V1V7=$51*0.0078 // AGP voltage
V1V8=$25*0.0093 // +1.8V
[Winbond W83637HF]
VT=1
V0=W83637HF Standard 1
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=(($25*0.016)-3.6)*5.14+3.6
V0V7=(($26*0.016)-3.6)*3.14+3.6
V1=ECS Photon PF2 Lite
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=255
V1V6=255
V1V7=255
[Analog Devices ADM1028]
VT=0
V0=not support by this device
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[Asus ASB100 (Bach)]
VT=1
V0=ASB100 Standard 1
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*3.8
V0V6=($25*(-0.016))*3.97
V0V7=($26*(-0.016))*1.666
V1=ASB100 Standard 2
V1V1=$20*0.016
V1V2=$21*0.016
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$24*0.016*4
V1V6=($25*(-0.016))*4
V1V7=($26*(-0.016))*1.666
[Analog Devices ADM1027]
VT=0
V0=ADM1027 Standard
V0V1=$21*4*0.00293
V0V2=$20*4*0.0032
V0V3=$22*4*0.0042
V0V4=$23*4*0.0065
V0V5=$24*4*0.0156
V0V6=255
V0V7=255
[ITE8722F]
VT=0
V0=ITE8722F Standard
V0V1=$20*0.01565
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$28*0.016 // vbat
V0V5=$24*0.016*3.8
V0V6=(($27*0.016)-3.6)*5.14+3.6
V0V7=255
[Asus Mozart2]
VT=0
V0=Mozart2 Standard
V0V1=$20*0.016
V0V2=255
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*4
V0V6=255
V0V7=255
[National LM85]
VT=0
V0=LM85 Standard
V0V1=$21*0.01176
V0V2=$20*0.013
V0V3=$22*0.0172
V0V4=$23*0.026
V0V5=$24*0.0627
V0V6=255
V0V7=255
[Winbond W83627HF/ADM1027 Combo]
VT=1
V0=W83627HF/ADM1027 Combo
V0V1=$20*0.016|0 // core0
V0V2=255
V0V3=255
V0V4=$23*4*0.0065|1 // +5
V0V5=$24*4*0.0156|1 // +12
V0V6=255
V0V7=255
[Winbond W83627HF/ADM1027 Combo]
V1=Tyan 2665
V1V1=$20*0.0.016|0 // core0
V1V2=$21*0.01471|0
V1V3=$22*0.032|0
V1V4=$23*4*0.0065|1 // +5
V1V5=$24*4*0.0156|1 // +12
V1V6=255
V1V7=255
[Analog Devices ADM1025/1030 Combo]
VT=0
V0=ADM1025/1030 Combo
V0V1=$21*0.012|1
V0V2=$20*0.013|1
V0V3=$22*0.0172|1
V0V4=$23*0.026|1
V0V5=$24*0.062|1
V0V6=$25*0.0172|1
V0V7=255
[Analog Devices ADM1030 Dual]
VT=0
V0=ADM1030 Dual
V0V1=255
V0V2=255
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[WinBond W83L785TR]
VT=0
V0=WinBond W83L785TR
V0V1=$20*0.044
V0V2=$21*0.044
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[WinBond W83L785R]
VT=0
V0=WinBond W83L785R
V0V1=$20*0.044
V0V2=$21*0.044
V0V3=255
V0V4=255
V0V5=255
V0V6=255
V0V7=255
[Winbond W83627THF-A]
VT=6
V0=Winbond W83627THF-A
V0V1=$20*0.016
V0V2=$21*0.016
V0V3=$22*0.016
V0V4=$23*0.016*1.68
V0V5=$24*0.016*4
V0V6=255
V0V7=255
V1=Asus P4P800
V1=Asus P4P800
V1V1=$20*0.01567
V1V2=255
V1V3=$22*0.016
V1V4=$23*0.016*1.68
V1V5=$21*0.016*3.8
V1V6=255
V1V7=255
V2=ASUS PC-DL
V2V1=$20*0.00488 + 0.69 // VCORE (pin 100) (+ 1.5V)
V2V2=$51*0.016B$05 // VBAT (pin 74) (+ 3.0V)
V2V3=$22*0.016 // VIN1 (pin 98) (+ 3.3V)
V2V4=$23*0.016*1.68

Checked and worked fine for windows xp x64 pro version too .
Just replace the voltage.ini
MBM 5.3.7.0 64bits can be downloaded at http://www.planetAMD64.com

Install issue nForce3 Ver. 5.11 on Neo2 Platinum

Hello,
I am putting together a PC using the K8N Neo2 Platinum motherboard (bios 1.C), Athlon XP3200+ (Venice Core) CPU, an ATI Radeon X800Pro AGP graphics card, 2 X 512mg sticks of ram, one 160gig SATA hard drive and LG4163 DVD burner. The on board sound has been enabled in the bios.
I had no problems with a straight forward install of Windows XP Pro. However, when I ran the chipset driver install (nForce3 -V5.11) that I downloaded from the nVidia website, the machine rebooted into a blank screen. I tried rebooting back into Windows without success. The boot sequence would post but Windows would just hand on a blank screen!
The only thing I could do (i have done this twice now) was a complete reinstall of Windows to try again. Unfortunately, when I tried to install those 5.11 drivewrs the same thing would happen. I have finally had some success by using ver. 5.03 from the MSI website and everything now seems ok. However, I would like to install the latest drivers especially if this is a known issue which has been resolved. Anyone gfot any advice on this??
Thanks

It's better to used the ver 5.10 as it much more stabile rather than 5.11 as it causing many problems.
Quote from: Tyrant on 14-August-06, 04:39:18
There are major problems with its IDE and LAN drivers. For example I get a BSOD or my rig reboots when it tries to install the network driver. After that Windows refuses to work again. Also the IDE driver has a SATA2 bug (when you use a SATA2 drive on the SATA1 nForce3) that causes a 30 second black screen delay right when XP starts to boot.
Latest official nForce3 driver is from 2005, and latest x64 driver is from 2004 and its beta... Now thats what I call being a lazy arse. You suck at drivers NVIDIA!
I also using SATAII hdd but jumpered it to SATA mode but yet i has no problem with that.
Also using the IDE n Sata drivers has no problem

Neo2 Platinum discovery - BIOSes above 1.5 don't like internal IDE cards

Similar Messages

Maybe you are looking for