Neo4 and amd3000+ s939 O/C help
my system is;
msi neo4 platinum
amd 3000+ s939
2x256 twinmos pc3200 ddr
msi 6200 td pcı express
I want to overclock this system. How to configure my system on beos for advice "Athlon64 3000+ (90 nm) @ 2.46 GHz (308 FSB), vcore = 1.450V, stock CPU fan, 3x HTT
PC3200 RAM @ CL2-3-3-6-1T, 2.8V,"
Hight performance mode : manuel
aggressive timing : disable
dynamic overclocking : disable
Adjust CPU FSB Frequency : 308
HT Frequency : 3x
HT Width : ? ? (how to)
SATA spreed spectrum : disable
PCIE spread spectrum : disable
PCIE Clock : 100
SSE/SSE2 : enable
Cool'n Quiet : disable
Adjust CPU ratio : ? (haw to)
Adjust CPU VID : ? (how to)
CPU voltage : 1.450
Memory voltage : 2.8
NF4 voltage : ? (how to)
memory setting ---------------------
Timing mode : ?
memclock index value : ?
CAS# latency (Tcl) : 2
Min RAS# active time : 6
RAS# to CAS# delay : 3
Row precharge time : 3
Trc : auto
Trfc : auto
Trrd : auto
Twr : auto
Twr : auto
Twtr : auto
Trwt : auto
Tref : auto
user config mode : auto
Botton of 32bit : ? ?
1T/2T Memory timing : 1T
Read Preamle value : ?
async latency value : ?
no bosd here, memory set to 2t after suggestion at 3-4-4-8, which is default for the 200mhz ram. system very stable upon boot with ht at 4 X 230, cpu at 2.07G, and ram at 460mhz. no ram issue here, tested it, even tried dropping the ram to 166mhz but same thing, MY SYSTEM WONT BOOT 2 TIMES OUT OF 10, OR APPROXIMATLY THAT. it wont even post, my screen doesnt even turn the green light, no speaker confirmation too, and the weird thing is that , i dont even have to clear my cmos. , upon pressing 2 or three times my restart button my system boots normally in o/c mode. no dynamic o/c or aggressive timings here. i like very much my board,and every thing is perfectly stable and reliable, i dont thing that its the psu, its a new thermaltake tr2 single rail 430w with 30amps.so thats the most ive couldve put out of it, and i dont want to force it more cuz its enough for, at 2.07g, my sempron outruns by far the athlon 3200+ in the sandra benchmarks. i dont want to repeat myself but thats the weird thing it doesnt boot always, but most of the time yes it boots.
thanx a lot
Similar Messages
-
When i disconnect my iPod 2nd Gen from my laptop, its display goes off and working freezes. Please help me.
The computer freezes? There may be something wrong with the USB port. If the laptop has more than one port, does this happen on any port? If you are disconnecting the shuffle cable from the computer, does it make any difference if you disconnect the shuffle at the other end of the cable first, then disconnect the cable from computer? Or if you currently disconnect the shuffle from cable first, try it the other way.
You may be able to work around this problem, if you get a self-powered USB hub. Something like this one
http://eshop.macsales.com/item/NewerTech/USB2HB7PRO/
There are many choices, but be sure to get one that has its own power supply. You can leave the shuffle cable connected to the hub, and connect the shuffle to the hub, instead of directly to the computer. This may provide a "buffer" for whatever is causing your laptop to shut off when the shuffle is disconnected. Since the hub has its own power supply, it will not rely on the computer for power to re-charge the battery. -
ipod nano 3rd gen - tracks (whole albums) have disappeared from ipod but are showing ticked in itunes library and ipod is synched, have bought tracks from itunes since this happened and they are fine, any help please
You may have transferred all your songs, but your iPad is seeing the library as a different entity.
The following article(s) may help you.
Moving your iTunes library to a new computer -
My iphone 4S stopped receiving and sending text messges. Help!
My iphone 4S stopped receiving and sending text messges. Help!
Hi J.A. Curie!
Here is an article that can help you troubleshoot this issue:
iOS: Troubleshooting Messages
http://support.apple.com/kb/ts2755
Thanks for coming to the Apple Support Communities!
Cheers,
Braden -
My Itunes is no longer allowing me to manage my music on my phone i can no longer select on my iphone to make playlists and delete music. Please help fix my problem. Iphone4s, 32gigs, IOS 7.1.2
I don't know why it stopped working but it happened a month or two ago but the option on this phone that's usually all the way to the left when you select your device but now its not and I don't know what caused it. ive already tried troubleshooting my problem but have found no help.Hello Salmomma,
Thank you for the details of the issue you are experiencing when trying to connect your iPhone to your Mac. I recommend following the steps in the tutorial below for an issue like this:
iPhone not appearing in iTunes
http://www.apple.com/support/iphone/assistant/itunes/
Additionally, you can delete music directly from the iPhone by swiping the song:
Delete a song from iPhone: In Songs, swipe the song, then tap Delete.
iPhone User Guide
http://manuals.info.apple.com/MANUALS/1000/MA1658/en_US/iphone_ios6_user_guide.p df
Thank you for using Apple Support Communities.
Best,
Sheila M. -
Hi
I've a big problem with adobe acrobat reader XI pro and I hope you can help me.
The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reader (adobe pdf reader, internet browsers, ...etc.).
This problem started to happen since yesterday when I installed adobe acrobat reader XI pro to try it before I buy it, and before that when I was using the free adobe pdf reader I was totally able to copy any text from any pdf and past it anywhere with nothing wrong.
What can I do?
thank you a lot.There is no product called Adobe Acrobat Reader Pro. There is
- Adobe Acrobat Pro ($$)
- Adobe Reader (free)
Which do you have? And are you a programmer? -
I have an ipad mini 1st gen 64 gb (wifi only) and i have problem with some of my apps. These apps have lags when you play with them for a few seconds the apps are having lags are call of duty strike team, gta San Andreas and nfs most wanted.pleas help me
I'm going to guess videos buffer for a while also...
Two possibilities, one is you should close apps on the iPad, the other is your internet speed is not able to handle the demands of a high speed device.
To close apps: Double click home button, swipe up to close the apps.
To solve internet problem, contact your provider. Basic internet is not enough for video games and movies. Your router may be old and slow. -
My apps wont open and i keep downloading new apps, hard resetting, syncing and nothing works! PLEASE HELP
Then restore the iPod. First from backup and if problem persists, restore to factory defaults/new iPod.
-
i spend a long time to try to sync my itunes music on my ipod 160 GB Classic, but after waiting so long get a pop up message that itunes stop syncing because of error 46, some times giving me 58, 1469, and many other numbers, please help am using macbook pro
That is precisely what my mid-2010 MacBoook Pro 13 was doing before the drive finally died after an Apple Genius rebooted it a dozen or so times. I have since read about the exact same thing happening to others, including a writer for The Atlantic magazine who had never had an issue with a Mac before. Do a back-up ASAP to make sure you don't lose anything and see about replacing the HDD. It is only about $140 for a new drive. The real issue is if you lose your data, too. So, make sure you do that back-up!
-
I have tried restoring an Ipod Nano 6th Generation but it seems to keep looping back and saying it is in recovery and needs restoring, can anyone help?
Try doing a level reformat of the iPod's flash storage instead to see if that kills the restore loop using the instructions in the article below.
http://www.methodshop.com/gadgets/ipodsupport/erase/
B-rock -
I can't open PSE. Get error message 150:30 and restarting computer doesn't help. Any suggestions?
Please try out the instructions mentioned in this article.
Thanks!! -
Unable to load ITUNES onto PC HP, windows 7 Home Version. Error message reads "Application Application Support not found". "Uninstall and reload". I have done that 4 times on Explorer and Firefox without success. Help??
I had gotten a similar problem, except with "provider services", i believe, but i solved it by copying sqlite3.dll from E:\Program Files\Common Files\Apple\Apple Application Support to E:\Program Files\Common Files\Apple\Mobile Device Support. doing that solved my first problem, but now i have been getting the error described in this topic (unable to load dataclass info... etc.). i tried reinstalling itunes (i already had 9.1.1, and thats what i reinstalled) by using the method described on apples site (using the "remove programs" tool in the control panel) and then downloading and installing itunes. when i opened it again, i still got the same error, and just now i got an error saying "the instruction at "0x00aadb6b" referenced memory at "0x00000008". the memory could not be read" it gave me the option to cancel and debug, or to press ok and terminate the program. I tried pressing cancel, and the popup went away but nothing else happened. a minute later the popup was back, so i pressed ok and itunes quit. Upon opening Itunes again, i got the very same error. sorry for the long post, but its really been bugging me. thanks for any help you might give, and if you need anymore info, feel free to contact me.
-
i can't use indesign since upgrade, it keeps asking me to upgrade java which I have done and still wont open please help me i have a deadline
DL the SE 6 JRE from http://support.apple.com/kb/DL1572.
27" i7 iMac (Mid 2011) refurb, OS X Yo (10.10.1), Mavs, ML & SL, G4 450 MP w/10.5 & 9.2.2 -
my iphone 4s wont turn on with out being pluged in and when i unplug it it dies instantly i pluged it in put it in dfu mode and tried to restore it hoping it might help but its stuck in dfu and has restore error 21 help!!!
Hey jestinsinclairr,
Thanks for using Apple Support Communities.
After reviewing your post, it sounds like you had one issue and then got a second trying to resolve the first. A frustrating situation for sure. The first article linked has what to do if it is not powering on unless plugged in. The second article addresses the error you are receiving when trying to restore.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Resolve iOS update and restore errors
http://support.apple.com/kb/TS3694#10
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
Have a nice day,
Mario -
I updated my iPod touch 4g 64gb to iOS 6.1 and now it's been very slow, safari keeps crashing, apps being very slow and crashing ? Can anyone help ?
Next
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Go to Settings>Safari and Clear Cookies, Data and History
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
Maybe you are looking for
-
Corrupted RAW files show in Bridge but not Photoshop?
Hi, I have recovered some RAW files that were accidently deleted but most of them are corrupt in windows explorer (using recuva). Adobe Bridge can see them but nothing else will open the files (or see them). I really need to edit these files, any h
-
Can I use any Class in a Use Bean Tag of a JSP
I have tried to modify the existing EditForm.java file and created a new Class File which changes the presentation(render method)in the Edit Form. can I use the new class as a Bean in the use bean tag of a JSP.
-
What is the scenario to get TRANCODE 25 ?
What is the scenario to get TRANCODE 25? Thanks in advance.
-
[svn] 4885: Flex SDK Framework - Update mx.filters API and class hierarchy
Revision: 4885 Author: [email protected] Date: 2009-02-06 16:12:32 -0800 (Fri, 06 Feb 2009) Log Message: Flex SDK Framework - Update mx.filters API and class hierarchy - Removed BaseFilter.as, BaseDimensionFilter.as, and GradientFilter.as - Renamed IB
-
Exporting from Fireworks to Dreamweaver
Hey guys/gals I have a problem. I have posted two previous posts, and got some really helpful answers. I am basically done with my website (I just need to make text boxes editable, put some more links) and that is it. By the looks of it, all of this