Neo4 Plat CPU and VGA cooling

Just wanted to get a few opinions on good and quiet cooling for my CPU and Vid card.
Neo4 Plat board; AMD Athlon 64 3500+ CPU
GeForce 6800 Ultra
I've read a lot of reviews and it seems that Zalman is the quietest way to go.
VF700-AlCu for Vid card
and
CNPS7000-AlCu for CPU
Is anyone using this setup, can you post your opinions?
Other recommendations?
Thanks.

Agree with that GPU cooler
I used to have a Arctic silencer, but the fan is only balanced @100% (I tested 3), therfore to noisy 4 my taste. I put the Zalman on the NBfan connector, and the NB fan on a handy 5v connector that came with the Zalman.
This way corecenter manages the fan speed, which is handy cus the Zalman also blows over the HTT hub hsf 8)
Best cooler 4 ur board is the thermalright XP90, according to this list:
http://www.overclockers.com/articles373/p4sum.asp
Get a Vantec Stealth or Panaflo fan to mount on it. @stock u should be able to keep it round 1000rpm.

Similar Messages

Cpu and chipset cooling,recommendations?

Trying to figure out what the best HS is for a 3400 on the K8N and chipset cooler. Stock HS running about 35-41 sys temp and 40-51 cpu (Idle/load). sitting at 41 sys and 45cpu right now, weird.... Its all in a coolermaster "stacker?" case. Good airflow (1x120, 2x80 front and 1x80 side intake, 1x120, 3x80 out...) Going to add the "crossblower" fan as soon as I can find it in stock. Had thoughht about the coolermaster hyper 6 but its huge, would have to tie it off to the psu plate or something to keep it from shifting I think
I was looking at the ZALMAN CNPS7000A-AlCu
http://www.newegg.com/app/viewProductDesc.asp?description=35-118-108&catalog=23&manufactory=BROWSE
I like the idea of quiet but summer is coming up and temps rise.... I also was thinking of running a duct from an 80 on the back or side to the HS fan as in intake and I dont think you can do it with the zalman. Any ideas? Not looking for a 92mm tornado setup, have to please the wife...
the chipset cooler gets me, have never bought one. Would like to be able to get one with a fan and plug into the board. Any thoughts on which one will work best?

Check some of the signatures here on the nVidia Athlon64 section of the Forum. That will give you a good idea of the Heatsink/fan combinations that are used!
I think the stock HSF is O.K., and I personally use the Zalman 7000AlCu....but there are other good ones!
P.S. while playing around yesterday....I opened the case up and put an additional fan on the exposed areas and it definitely dropped my temps about 8 deg. I'm thinking of adding a side case fan to help ventilation. I've got the Lian-Li PC-65 black aluminum case.

CPU and NB cooling queries...

Hello to all...
I'm wondering if anyone has removed the MSI lightshow heatsink and fan combo from the northbridge chip and put on something else, say like the Zalman NB coolers? I was thinking of the ZM-NB47J cooler but as the mobo has those slots in the board for the hooks rather then holes for punch throughs, i wasn't sure if anyone had got it to work.
i was thinking that the crossbar from the stock heatsink and fan might be able to work with the Zalman, but wanted to check with other users first.
As for CPU coolers, i just changed from my Antec Sonata case to a Overture and now my Zalman 6500 cpu heatsink and fan won't work as the fan mounts to the PCI rail and there's not enough height in the case for that. I figure i'll try a 7000 series...but there seem to be mixed answers on whether or not it will fit properly as the socket isn't centered within the mounting brackets. Any help there would be appriciated.
Your thoughts, comments, ideas are appriciated.
Thanks.
G.

Quote
Originally posted by Upstart
So i take it you're happy with the combo of the Zalman 7000, heatpipe on your vid card and the swiftec NB heatsink? I think i might follow suit.
Yeah, that combo works well for me. I haven't tried many other cooling options, so there may be better options out there. There's a new video card heatsink similar to the Zalman with two heatpipes and a Swiftech CPU heatsink with heatpipes. If I had to do it over again, I'd give those a try.
If your goal is low noise (like mine), you can't beat the undisputed champion of low-noise CPU heatsinks - the beautiful Heatlane Zen. I used this heatsink in another PC and it performs quite well. With a case that moves enough air, the Heatlane Zen is worth a try.

K8N Neo4 Plat, SATA2 and Shutdown Problem...

Hi, new here.
Glad to have a board like this to ask some questions to other users.
Purchased the board a few months ago, and apart from the noisy NB fan, all was ok.
Then recently bought a 200GB SATA2 drive (see specs in signature).
Since its installation, but not before, I've had a systematic shutdown and reboot problem: the shutdown proceeds as usual, the "Windows is shutting down" and "Saving preferences" dialogs come and then disapear... but then only the mouse cursor is left on blank screen (it can even be moved), and the shutdown process doesn't go further; after several minutes I just shut it down with the power button.
The event logs don't show anything problematic.
A few more details:
My drivers are the most recent (official) from MSI.
I've installed Win2000 in ACPI Uniprocessor PC Mode.
The drive is recognized as a sata2 device.
I use the SATA#1 (nVidia) port.
I've put the pagefile on that drive.
Nothing is overclocked, CoreCenter is disabled.
I've installed the UPH Clean tool from Microsoft, but that didn't help.
Memory passed lengthy memtest session.
Strangely, the SATA2 drive appears in the "Unplug or Eject Hardware" list in the tray, usually reserved for connectable devices (USB, etc): is that normal? (I'm new to sata drives)
I've searched this board for similar problems, but they seemed to be mostly in RAID context, which isn't the case for my system.
Any idea what might be the problem ? Anyone experienced the same problem (non-RAID) ?
Apart from above problem, drive seems to function normally.
Thanks in advance.

@gerasimatos: maybe he used xsetup? didn't try it yet, will have a look. In the BIOS, all RAID-related settings are disabled.
@kakarocht: the power managment in the BIOS has the default settings.
Will try to change a few params here and there.
I have not tried yet other ports on nVidia controllers.
I may eventually try the Sil ports, in last resorts, BUT I would prefer to solve this issue with nVidia ports first (I think at the price we pay these things we shouldn't be precluded from half the SATA ports! )
I tried to list as much relevant specs as I could in the signature and post. Here are others:
memory used at 2.5-3-3-7 1T setting (memtest passed)
regular ps/2 keyboard
ms intellimouse (using ps/2 connection)
the asus graphic card used in single monitor mode (recent drivers)
when I said "CoreCenter" disabled above, meant "Cool'n'Quiet" disabled (not stressing system yet, so 'cool' isn't an issue; as for quiet, if the board can't lower the NB fan speed, it's a non-issue!!!)
using on-board sound-card
using onboard gigabit port for internet connection
no other peripherals installed presently
hard drives temps stay under 40 C (not stressing system lately)
I removed DigiCell and CoreCenter from loading at startup (don't need them for now)
closing firewall (zonelalarm) before shutdown didn't help (although didn't try unloading the service yet)
... what else might be of help to list?...
Again, I'd like to know if it's normal that a SATA2 hd drive appear in the "Unplug and Eject Hardware" tray icon list; I wasn't expecting that, but I'm new to this kind of connection.

NEO4 Plat/sli and the Active armor/network issues

Ok first of all my computer was running fine with my ethernet pluged into the primary nforce gig lan. After installing this software it worked for about 5 hours then just cut off my internet. I then plugged it into the Yukon pci-e gig lan and it worked then. After uninstalling this software i can no longer get a connection on my Nvidia lan. it connects but wont send/recieve any packets. Also windows will not even let me repair my connection without it locking up the network settings. If anyone can help i will appriecate it.
Andrew

no yellow marks in device manager the card says its working but i disabled it because it wouldnt work. i have the newest drivers and the most updated windows xp sp2.
Andrew

Max stable CPU voltage supported by K8n Neo4 Plat.?

My vcore voltage fluctuates between 1.44v and 1.50v. In the bios I have 1.42+6.6%(see my sig). I have ran prime 95 for 24h stable, but recently I tried OCCT(a french program). The first test ran for 30min OK, the torture test froze my computer within an hour or two. My question is what is Max stable CPU voltage supported by K8n Neo4 Plat.?Because obviously when the mobo drops it to 1.44 it IS NOT ENOUGH. Difference of .06v obviously is critical for the stability. Anyway it should be 1.425+6.6%=1.519 which is nowhere near 1.44. I currently run at 36-38C idle and 45C under load. Is it a bios problem? I use 1.6 bios and I don't have any problems whatsoever.
Any opinions appreciated.
BTW tried to raise the mobo voltage at 1.55(1.50 default) but seems that there is no difference.
BIOS shows my voltages as follows:
+3.3v=3.12 to 3.15 mostly stays at 3.14 pc wizard shows 3.14, core center shows 3.22
+5.5v=4.96 to 4.99
+12v =11.96 to 12.22 core center shows 11.96, pc wizard shows 12.22

Quote from: gerasimatos on 30-September-05, 09:17:54
dont blame MSI for your financial situations. If you could afford the proper hardware then you wouldnt need to overclock and such. JMO.
I can afford the proper hardware. In fact, I bought a DFI Lanparty nF4 SLI DR to replace the defective K8N Neo4 SLI board.
As soon as the new K8N board comes back from RMA, I figure to sell it - say half off. I think for something that may or may not work as advertised, half price is fair.
And speaking of processors, these Venice chips are really phenomenal - they're just like (or maybe even better than) the good old XP1700 JIUHB chips. I still have one of those - and strangely enough, it's still running - in an MSI K7T Turbo 2 board (KT133A). That JIUHB served me well - it'd do a 500MHz overclock with no strain at all. If I had water cooling, I bet I coulda got 1 GHz out of it.
The two Venice 3200 processors I have both seem to be really good overclockers. The one that was in the rig I RMA'd is the best - right now in the new Lanparty board, I've got it running at 2.5 GHz (1:1 @ 250 MHz) with about 1.55 volts. It's idling at about 30c and only runs at about 44c under load - and the AS5 hasn't even cured yet!
That chip is gonna be one helluva overclocker!
I'll let it run at 2.5 GHz for another week or so till the AS5 has cured, then I'll see just how far I can go (without the temps getting too high). The way it's gone from this point, I think 2.7 GHz is very reasonable for a goal.
And as I think newbie222 pointed out, as long as the temps are kept reasonable, there is no actual risk to the processor.
The point I was making is that with my old, defective K8N, that would not have been possible - BECAUSE THE BOARD WAS DEFECTIVE. It was defective because the vcore did not operate up to spec (wouldn't go as high as it was advertised to) and because of the voltage fluctuations.
How would you feel if you bought a new car that was advertised as getting 24 MPG highway and it only got 17 MPG? Or if you ordered Comcast's 8 Mb/s downstream Gold Tier and only got 6 Mb/s downstream? Or if you ordered a 102 channel cable package that turned out to only have 88 channels?
It's all the same exact, precise thing.
If MSI advertises you can get a vcore of 1.7> volts then you fer damned sure better be able to get it.
The main reason people buy boards like the K8N is to overclock - it's the "enthusiast" community that the board is targeted to.
I find it hard to believe anyone would even want to buy one of these boards and not overclock. What's the point? If all someone wants is something that will run at stock speeds, then they oughta save a few bucks and buy a Dell or whatever.

Cooling gpu, cpu and viedo question!!

hi guys.. i have been really concern about the temps in my pc and sometime corecenter tkae me out of a game becouse of the temps.. so i descided to get ths
GPU: Vantec Iceberq Solid Copper VGA and Chipset Cooler - 10.95$
Memory: Vantec Iceberq DDR Copper Memory Cooler - 8.95$ x2
Video: Arctic Cooling ATI Silencer 4 (R420, X800) - 27.50$
CPU: i dont know wich one to get buecouse i dont know wich one is better and wich one will fit in my system any recommendations?? something aroud 50$ or less but i need this urgently
Ok,, what do you think?? will all this fit?? the vantec chipset cooler with the arctic silencer??? is tehre a better chipset cooler???
Which cooler should i buy for my cpu?? somethng taht fits but really get that cpu cooler.. This ones in the follow list are the ones that i cna get
Thermaltake xp-90 - 38.99$
Thermaltake xp-120 - 49.99$
Cooler Master Hyper 6 - 48.95$
MCX6400-V - 54.95$
Thermaltake Extreme Venus 12 - 39.95$
Thermaltake PIPE101 3 in 1 - 48.95$
Thermaltake Silent Tower Universal Heatpipe Cooler - 49.95$
Zalman CNPS7000A-AlCu - 38.50$
Zalman CNPS7000A-Cu - 48.50$
in casethat the heatsink come without fan.. wich one should i get???
My system is
AMD 3400 Clawhammer CG - 2200 Mhz Stock
MSI Nforce 3 250GB K8N Neo Platinium Edition - Bios 1.55 - 201FSBx11M
2x512 Corsair Value Select - 1T 2.5,3,3,6
Ati X800XT Platinium Edition - 520,560 stock - Catalyst BETA 4.10
2x80GB Western Digital 7200RPM
Lite-On 52x24x52
A4Tech 480 Watts
tks for all the comments and suggestions

I'd go with one of these
Zalman CNPS7000A-AlCu - 38.50$
Zalman CNPS7000A-Cu - 48.50$
Stay in the high 30's with the pure copper one. Best HSF out. I love mine.

K8N Neo4 Plat and 3500+ venice?

I have searched this but am more confused now than before. I am thinking of upgrading to the 3500+ venice with a K8N Neo4 Plat or sli is this a good combo.Tiger Direct has the Plat. and the SLI for the same price $149. Does this cpu work better with one or the other board?

i have the sli/plat and the 3500+ venice and it seems to work well with the 3.4 bios dont know about the plat but its basically the same. just my input

Will Zalman's passive VGA-cooling work with their CPU-cooler on K8N?

I'm thinking of getting the
¤ Zalman ZM80D-HP VGA Dual Heatpipe
combined with
¤ Zalman ZM-7000A-CU
Will they both fit on a K8N? EDIT: What I'm asking is wether there is enough space to fit them both, not compatibility.
What other passive VGA-cooling will work/won't work?
Thanks!

Quote
Originally posted by sui
well, you could compromise and get an arctic cooling vga silencer... they are very quiet. the only issue is room above the nf3 chipset and it will take up 2 pci slots below.
OK, I'll think about that and read some reviews. I've allready read good stuff about it, just haven't considdered it, cause I thought 'why go low-noise if you can go no-noise', but since this cooler draws air out of the case, other fans could possibly spin slower, so it may be a contestant.
Quote
Originally posted by Fladlish
Hmm yes you can use them togehter, but you'll have to do some ghetto Modding though.
And One or two PCI holders won't be useable.
And It won't be pretty at all.
I know, I did it
se http://it.hule.harryda.se/itda00b/freejs/data
The 9800 Pro doesn't have any temp reader, but with the fan @ 5v it got really hot to the touch, now days I'm using a potentiometer controlling all the fans in the computer, and surfing the web etc it doesn't really matter if the GPU get's a little hot.
That was innovative! Don't have the guts to do such a thing though. Since I haven't bought my stuff yet, I'll rather play safe and try other solutions.
BTW: Do you mind if a post a link to this modding on the sweclockers forum? It might help someone there.

Need help ASAP: No video card signal for neo4 plat

I just bought a new case, motherboard, ram, video card, power supply, and CPU. i took my drives from my old Dell and placed them into this case and the MSI neo4 plat. motherboard (specs at the bottom). after getting it to post, i noticed there was no video. i triple checked for anything that wasn't hooked up or loose. everything seemed good. i'm using a VGA monitor. i looked at the D-bracket 2 and noticed that it had 3 red lights and one green in the lower right hand corner. in the manual this means no video signal... well obviously. what does this mean and how can i fix it? my video card's fan is working. i see no spot for a PCI express power input. any ideas? i use my computer a lot and need to do some things before i leave for vacation on the 15th. i'd like to resolve any issues before i leave so i can relax about it when i get back.
thanks,
Zack

well it seems things have gotten worse, after taking out the ram the other day and putting it back in thinking it was a ram problem, which it turned out not to be, it is giving me a ram problem. i just snapped em in a few times in all possible configurations and nothing is changing.

Newbie with MSI neo4 Plat

hey there,
my 1st post here.
MOBO: MSI Neo4 Plat
Graphic: MSI 7600GS
CPU : AMD X2 3800+
power supply: 500W
recently i got this problem. Randomly my display goes blank, like the PC is on standby. The pc seems to be running but the monitor seems to be set to standby.
after i restart the PC(only able to do by the reset button, cannot Ctrl+Alt+del) everything seems to be ok.
the problem seems to occur randomly.
anyone have any idea what's going on here?
thanx for reading.
cheers!

Quote from: okta on 02-June-06, 00:35:16
hey there,
my 1st post here.
MOBO: MSI Neo4 Plat
Graphic: MSI 7600GS
CPU : AMD X2 3800+
power supply: 500W
recently i got this problem. Randomly my display goes blank, like the PC is on standby. The pc seems to be running but the monitor seems to be set to standby.
after i restart the PC(only able to do by the reset button, cannot Ctrl+Alt+del) everything seems to be ok.
the problem seems to occur randomly.
What kind of monitor, how is it connected and does it use calibration software. I've seen this with Samsung (and some OEM brands made by Samsung) monitors, which use Magictune, connected to the DVI port. Basically Magictune is crap ands clobbers the monitor's EDID info so that it switches to the VGA port - you can check this by plugging in the VGA cable. Depending on the monitor, it can cause permanent damage to the monitor's firmware which requires a firmware re-burn... or as apparently in your case, temporary damage which is fixed with a reboot. The only solution is to get a newer version of Magictune.. or dump it completely.

CPU Fan Speed- (Cool 'n' Quiet)

Recently I did a reformat of my computer and now I’m having a weird issue.
I’ve always had Cool ‘n’ Quiet enabled and my system would spin down the fan accordingly (not the CPU speed) but now my fan is at around 3200rpm until I turn on Core Center, it drops to about 1000rpm (as it was the case before my reformat)
My question is there any way to enable Cool ‘n’ Quiet without turning on Core Center, or any 3-rd party application for that matter. (as was the case for me previously)
Also if I turn off power management in windows my CPU gets throttled, I do not want this, I only want the fan to throttle accordingly
Neo4 Plat. 1.x (BIOS 1.D)
TIA!

Ohh... is that what it is... I saw that setting but i just ignored it. I musta had it on previously. So setting it to say 50C should do the trick?

CPU and GPU slow down after system upgrade

Ok, I can't find anything similar to the question I have...but this forum goes on forever
As my system specs appear below, my machine was running quite comfortably a week ago, with same setup...minus the acrylic case and second 120GB hard drive.
At that stage I had "nomal" benchmarking scores 3dmark03 - 5850, Aquamark3 41.000, PC mark 2002 - cpu7020 mem8438 hdd1050.
Life was good and I loved my system
Then I decided it would be cool to upgrade to an acrylic case (which has better cooling with 3 fans) and a second 120 GB HDD to make a striped raid array.
My first concern was the raid Array. I was carefull to buy the exact same seagate hard drive, size etc. the original was only a month old anyway. The second was to use the intel southbridge chip for SATA RAID or the Promise controller? After researching these forums I decided to go with the Intel as it has more possible bandwidth and doesn't sit on the PCI bus.
I got the new case and wearing those stupid white gloves, proceeded to move the components over and trash my "old" metal case.
The windows NTFS format (full) flew by in 30 seconds and I was really impressed.
Once windows xp and all it's drivers and updates were installed, incl sound and graphics etc. I did a 3Dmark 2001 test before upgrading to Dx9...what a bad mark! 3Dmark2001SE - 9950 (terrible for this system).
I thought it was a DX problem...so I installed Dx9
Then opened that corecenter program (the old one, the one that doesn't crash...)
and my CPU was about 5c hotter than usual, it was running at 40-42c (I have standard intel cooling fan). It went up to 55 at times when running PC mark 2002.
This didn't concern me too much a the system was stable at 32-34c and the northbridge read 60c (but we all know that's not true , more like 35ish.
My PC mark 2002 is now cpu4200 - mem4800 - hdd1800
(at least the HDD improved!) LOL
I ran Aquamark3 next...29,900 (ouch!)
Previously my CPU was 8,700 and GPU was 5300
now the CPU read 4400 and the GPU 4600
I don't really notice the speed loss when working, but games and benchmarks tell a different story.
So, My question: What has happened? Why is my CPU power cut in half? and the graphics card slightly slower? The memory speed stayed the same and the HDD speed improved....not a worthwhile upgrade IMO
What went wrong?
Here are my theories.
1) The CPU and system case is getting too hot
Does the CPU "throttle" when it overheats? this could be the reason.
Also both HDD get really hot and the fan in front blows air over them, this hot air could be going over the CPU or GPU. Maybe get 2 HDD coolers?
should I buy a better CPU cooler like the Thermaltake spark7+ ?
2) The PSU does not have enough watts
I couldn't find traces of voltage lack or spikes...but it could still be a problem
3) The RAID0 array is a strain on the CPU and chipset
I'm not sure about this.
My appologies for the lengthy thread, but I wanted to be sure that anyone trying to figure this out had as much info as possible
Thanks if u can help me figure this out.

Quote
Originally posted by Reaver
When I originally installed the intel p4 cooler, I used artic silver ceramique paste...and the CPU temp operates at 36-38c with no load.
Perhaps I should upgrade the overall cooling. Get a Thermaltake copper fan and two HDD coolers.
Well, your temps sound allright, no need to worry them, if they really operate at that level.
Quote
The solution to set the FSB to 201Mhz sounds good. But do I set this in the BIOS or with Corecenter in windoze?
Propably meant to adust your FSB at BIOS, at least that is what I would suggest.
Quote
I will try to re-install the VGA drivers because something strange DID happen when I first installed them. I started with the hercules driver CD, this installed CAT 3.2 drivers. I then upgraded to CAT 3.7 and before it completed I got an error window (send, dont send).
Remove drivers AND ATI control panel first, and then re-install. Use drivers from ATI site, and rather Catalyst 3.7. I Have had problems with 3.8 Catalysts.
Quote
Still wouldn't explain why the CPU seems so crippled. I have managed to get a "normal cpu score of 7000+ in PCmark2002 by shutting down, restarting later and killing every process except explorer.
Do you have any processes that seem to eat more juice thant hey should? Arrange your processes by CPU usage and see if there is something strange.
Quote
If this cant be fixed I will reinstall over the weekend. Does anyone know of the RAID0 array on the southbridge causing a system slowdown?
I'm using Intel RAID and it works perfectly, no extra CPU usage is shown and it's pleasantly fast!
And Install latest Intel INF updates and Application Accelerator from Intel site. That's what I'm using, and works fine.

KT3 Ultra2 R and VGA problem

I wonder if I could please get some ideas as regard this rather odd problem which I am encountering. This problem occurs when while the pc is 'shut down' if I disconnect the power supply ie switch off power by way of the switch on the psu. When I switch power back on again and boot, the pc begins its booting sequence it begins to launch windows and then it stops and a little red square (with a bit of green) appears in the top left hand corner of the screen. Now this problem does not occur if I shut down the pc normally (but don't cut off power supply). I have several partitions on my HDD and they are all affect at the same time. The end result is that I boot into safe mode I look at the refresh rate which is set to 'unknown' change it to 'adapter default' then reboot but upon reboot I get windows displaying screen at 640x480 with standard vga colours. I check in device manager under 'display adapters' what driver it's showing and it's the driver which I last loaded ie the correct one. I cannot change screen resolution , bit colour and the refresh rate only allows for 2 options, either 'optimal' or 'adapter default'. In order to get back to where I was, I have to remove and re-install my VGA driver and then everyting is back to normal (until I switch off power again at psu then back to square one). I have spoken to the manufacturers of the graphics card and they say that if the card works ok when I shut down pc normally and restart then cannot be the card. I described my problem in greater detail to MSI support and they said either VGA or O/S.
In essence I wanted to isolate the problem to, is it 'hardware or 'software'.
I would be grateful if anyone can shed some light.
KT3 Ultra2 R (5.5 not the right one but the cpu clock speed is correct at post)
XP 2600+ 333 T'Bred
Crucial 512 Mb PC 2700
Leadted Ti 4400 128 MB Vivo (det 44.03)
Creative Audigy
Enermax 432W
Windows 98SE (via 4-1 v 4.34)
Seagate 60Gb 7200rpm I am running the HDDs as independant drives on the
Seagate 40Gb 7200rpm Raid controller ie one on IDE3 & one on IDE4

Odd as it might seem I have to follow the proceedure listed below if I want to switch off power altogether to work on my pc.
1. Cold boot system with 166FSB and let O/S install
2. Reboot enter Bios and reduce FSB to 133 make sure to set memory speed as HCLK and let O/S load
3. Shut down and switch off power supply
4. Reconnect power and boot system. Enter bios set FSB to 166 (the mem speed will be HCLK)
5. System continues to boot and loads O/S
From that point on, cold boots (without cutting power supply) are not problematic as once the 166FSB is 'registered' everything works ok (at every cold boot). So anytime I wanna work on my pc I guess I have to do the above 5 steps. They seem to work but need to try it out a few more times before I am confident that this process will always work.
I am sure you agree that this is one strange mother of a problem.
I suppose the only 2 things left are a total O/S reload or trying another 333 cpu because I have tried everything else. I guess I will have to live with it.
I have also cut some additional front vents so that front fan draws more air in and it appears to have dropped my idle Temp to 40.5C on CPU (running at clock 2083Mhz).
As as said earlier in my post my system ran perfectly with XP2000+ and 512Mb PC2100. I merely upgraded the CPU to XP2600 and mem to PC2700 and it has thrown up this very odd problem. And to boot (if you will pardon the expression) when I first installed new CPU and memory it booted first time at 166FSB. osnavi, in case you upgrade your CPU to a XP2600 and you get this weird problem at least you can come back to to this thread and find this workaround.
I wonder if anyone can fathom out why this is happening.......If not as I said I can live with it.
wonkanoby, I will try the link to the memtest. That is the only thing I have not tested so will give that a try.
-MSI KT3 Ultra2 Raid
-AMD XP2600+ 333 T'Bred
-Evercool CUD 725 Cooler
-2x256 Mb PC 2700 Crucial
-Leadtek Ti4400 128Mb Vivo
-Creative Audigy
-LiteOn DVD 16x
-Liteon CDR48125w
-HP CDR 9710i
-Seagate Barracuda IV 60Gb (I am running the HDDs on the raid
-Seagate Barracuda IV 40GB controller as 2 independant drives)
-2 Case fan
-Enermax 431W

MOVED: K89 NEO4 PLAT/SLI Do I have to send it back?

This topic has been moved to AMD64 nVidia Based board.
K89 NEO4 PLAT/SLI Do I have to send it back?

No worries.
As for the Bios flash all you need to do with a newer core top get it to come up for posting or Bios Adjustments/Flashing is to use a single Stick of RAM. That forces the CPU's Memory Controller into single channel and that will get it done. If you try to post in dual channel with older Bios's that do not fully support a newer chip it will lock and you need then just to remove all RAM except from Slot 1 and reset the Bios as per your user manual.
No worries as it is not as hard as it sounds.

Neo4 Plat CPU and VGA cooling

Similar Messages

Maybe you are looking for