Neo4 Wont boot.. no screen..HELP

Sighh.. I just recieved my new ram today and i still have the same problems =/ the bracket stalls on 3 red lights and 1 green light.. = memory problem. I have tried just 1 stick of ram.. dual.. every combination you can do..cleared cmos.. still wont boot up.. The motherboard is on my table out of the case with just RAM and CPU.. and D-Bracket LED shows LEDs 1 and 4 orange for a second, , then it goes to the memory error sequence (3 red LEDs, 1 green LED). All of the connected fans are spinning, including the CPU heatsink fan.. I think its the motherboard fault.. because ive tried 3 different ram sticks with this motherboard.. still the same problem.
Ive also took out the RAM and VID CARD and resetted my cmos.. and when i power it up, the dbracket said im missing memory.. so i reseted my cmos and added the ram in.. and it still saids im missing memory =/ but ive tried 3 different ram sticks.. and its still the same.
please help

I think you may have a bad board. You got this from Newegg right? Make an inquiry for an rma. The board shouldn't need any mysterious methods in getting it to POST. You've went the distance in trying to get this up and running. As long as you haven't tried to get your system up and running without having a hs/fan on the processor, I strongly lean toward you having gotten a bad board. It happens.

Similar Messages

HP DV4-1155SE Black Screen and Wont Boot. Please Help!

Hello all I am working on an Hp DV4-1155SE. I have tested the memory modules, the hard drive and everything else that I can take out of the computer easily. Everything works but!, The laptop will not boot into the bios or anything else. Black screen, wont boot and i have the bios file that HP supplies on the support page of the site. I have looked at the instructions that a few people have posted about re flashing the bios and that does not seem to help me at all with this AMD processor. If anyone can please offer any help at all this would be greatly appreciated.
Thank you!

I will search on int 19h....thanks.
My problem started before the bios-screen.
This is what I tried this evening:
- Disconnected all non-essential devices...no effect.
- Cleared the CMOS...system booted to OS! Screens still garbled!
- Put in an older graphics-card...No artifacts!
- Put my MSI NX6600GT (AGP) back in...screen grabled while booting. Once in OS everything
looks fine at first. Later I noticed some odd random pixels. Playing movies is working fine.
Playing 3D games results in all kinds of strange looking artifacts.
- Installed the latest NVidia- drivers...no effect.
Is my problem still MOBO related or Graphics Adapter?
Any further advice?
Thanks!

OSX wont boot - grey screen

Hi, I turned on my imac g4 15" 700mhz today to find that it wont boot osx at all!
When i start up the computer, i hear the chime, the light comes on and i hear the fan, hd etc. Then, the grey screen appears with a central finder logo (Which is normal, i think). This is when the computer freezes....HELP....WHAT CAN I DO?
I have tried several things suggested on the support pages such as booting from the cd which wouldn't allow me to do anthing - even re-install osx!

Not to get off the subject of the original post too much, but:
James,
I've encounted the same problem today on my work computer (a G5 Dual 2.5ghz). You'll likely have to do the same thing i did to recover your data:
Remove the drive, mount in another computer (you mentioned that you tried to firewire it to another G4). Instead, actually remove the drive from your machine and install in the other G4. Boot the other G4. Hopefully the drive will mount as a secondary drive. If so, back up your data. If not, run Disk Utility "Repair Disk" on it. You may have to run a third party app like Tech Tool Pro or Disk Warrior. Doing that should fix the drive enough for you to get the data off.
Even if it does, you should probably flatten the drive and do a clean install of the OS. Make sure you run Disk Utility again off the installer disk to insure the drive is competely repaired.
Worst case, you buy a new drive is you are worried about it crashing again. Either way, you should be able to get to your data with a little work.

Powermac G5 wont boot. Please help!!!

my PowerMac G5 wont boot, power suply or graphics card? When i press the power button is the chime and then after a while (fem minutes) the fans start revving up, all with a black screen........

See if it will come up into Open Firmware and let you do an NVRAM reset.
Hold the cmd-option-O-F key combination when powering. If the screen actually comes up, you should see a light background with black letters. To do the resed, enter the following three commands.
reset-nvram <enter>
set-defaults <enter>
reset-all <enter>
I don't have a lot of hope, in one sense, but it you get the OF terminal screen, then that says at least that at its basic guts, the machine is sort of working, and we can go from there. And, if it does make it into OF, the resets might actually clear things up.

IPad wont boot after screen replaced

Just replaced the screen on my sons iPad 4 and now it wont boot...
any suggestions please?
Thanks

Who did the replacement? If the screen was replaced due to a drop, there may be some internal damage or loose connection.
Some iPad users have been able to revive their dropped iPad. Turn the iPad over and give it a HARD SLAP on the back. May take several slaps.
dropped iPad
https://discussions.apple.com/thread/4474708?tstart=30
Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased.
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

T60 wont boot ~ I NEED HELP ~

H'ok.. So I was going to try to fix my friends T60 but I'm worried this is kinda over my head..
She came to me and said the OS was currupt and asked me to install a new os onto her laptop..
I was only able to install anything when the built in Wireless card was disabled..
Whenever you enable the wireless card, windows wont boot (all versions) nor will Windows installer boot..
Linux will boot though with the wireless card enabled.. but wont see a wireless network.
I've checked the hard drive and the ram.. both are ok.
I tried swapping the wireless card, but that didn't fix the problem..
Could it be the motherboard?
I need help! PLEASE WILL SOMEONE HELP!
~Jonny B

Could you try doing a system update using an ethernet cable? What OS are you using?
ThinkVantage System Update here:
http://support.lenovo.com/en_US/downloads/detail.page?&LegacyDocID=MIGR-66956
Here is the link for the ThinkVantage Productivity Center download:
http://support.lenovo.com/en_US/downloads/detail.page?&LegacyDocID=MIGR-61378
Think link lists all of the available ThinkVantage Technology Tools for your T61:
http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-61432#productivity
Let us know if that helps.
Did you find a post awesome? A great response? Kudo them!
Did the post you read answer your question? Did someone help you figure out your problem? Hit Solution Provided and give that person a 'thank you' for helping you out!

T60 froze. wont boot. black Screen

Hello.
My T60 2007 QPG froze.
Pushed the power button to shut down.
Now it wont boot: fan starts then stops, just a blank black screen, no beep or beep sequence.
After reading the board i removed cmos battery, ram, hdd: no beep indicating an error.
Any suggestion?
Thanks

Hello mate,
If you have no beep when you remove the RAM, your motherboard is dead.
Knowledge is of two kinds. We know a subject ourselves, or we know where we can find information on it.
ThinkPad T510 4313-CTO Windows 8 x64 - Intel Core i7-620M - NVIDIA NVS 3100M - 8GB RAM - 240GB SSD- Intel Centrino Ultimate-N 6300 - Gobi 2000.
ThinkPad Helix 3697-CTO Windows 8.1 x64 - Intel Core i7-3667U - Intel HD Graphics 4000 - 8GB RAM- 256GB SSD - Intel Centrino Advanced-N 6205 - Ericsson C5621gw

K8N NEO4 wont boot

hi,i have been given a pc that wont boot,the motherboard as far as i can gather is an msi K8N NEO4 MS-7125 N1996(thats all the info i can see on the motherboard) . 4 gig of ram not sure about the graphics card/pentium/hard drive because i havnt seen the machine working as yet.as soon as the machine is plugged in and power on plug socket is switched on i get a blue led flashing on the front panel and nothing else,i even get the light flashing when the psu power button is in the off position.i havnt tried unplugging everything from the mb yet,i just wondered if any of you guys knew what the flashing led was about? thanks

Quote from: Henry on 17-February-12, 13:11:59
"...board is relatively recent."
If you think 7 years as "relatively recent" that is. That's plenty of time for caps in PSU & MB to go bad, especially in PSU and not knowing what the original owner had, bad PSU is a good possibility for damaging MB.
Original was a Corsair 400 apparently.
It depends how you interprete "relatively". All my stuff is older than that so to me it's recent.

IMac wont boot...Help!!

(reporting live from my PC) I've got a 24" 2.4GHZ iMac (the hub of the house) that this morning when I went to get on it, was running INCREDIBLY slow, and none of the apps were responding and I couldnt Force Quit. So, I had to do a hard power off. When I restarted it, it seemed to be back to normal....for only about 10 minutes, then got sluggish as it previously did. Same routine. I rebooted a total of 3x. Now, when I power it on, I get the "Dong" sound, a grey screen with the Apple logo and spinning progress for 30-45 seconds, and it goes black and powers off. It wont even boot now!!
What do I do??? Thanks

You mention you are almost out of space, if you have less than 10% left that could be your problem however if not let's talk about HD upgrades. The difference in price between a 750 and 1TB isn't that much so as long as you're doing surgery my vote goes for the 1TB or even 1.5 TB. Any 3.5" is fine, I'd recommend 7200 RPM, 32MB buffer such as the Seagate Barracuda. Other World Computing (OWC ) has a good selection and helpful support staff too that can assist on a choice.
However back to the "Just about out of space on my 320 GB drive" comment. If you have less than 10% capacity left then you might try to get the system to boot up in Safe mode, transfer some material off to DVD or an external drive and then try booting in normal mode. If it works then I'd say that was the problem.
320 GB is a pretty good size drive although small by today's choices so you might want to evaluate what you're filling it up with. If you filling with photos or music or other HD hogs then you might want to consider storing that info on an external drive. For example I recently got into DSLR photography and shoot in raw, each picture is between 5-8 MB, so it became apparent it wouldn't take that long to fill up my 320 GB internal drive. For example today I went out and shot about 175 pictures which came to 1.8 GB. The solution was to get a 500 GB FW 800 drive and store photos and music there and use a 750 GB FW 800 external as my TM drive. And just for safety's sake I keep a redundant backup of all music and photo's on a slow USB 2.0 external, it's slow but it gets the job done.

T41 Series wont boot/Blank Screen

Hi Guys and Girls,
My Girlfriend recently inherited a T41 from her father and I decided to give it a clean up for her as her father had no anti spyware protection or anti-virus, so after installing a few programmes like AVAST and Spybot to clear it up we turned it off and yestreday when we tried rebooting for the first time, it went to the dreaded blue screen. So my GF resetted and now it wont even boot, power is commin through, the lights are on, I can here the drive on, but screen is blank, and nothing is happening. Can anyone help? would it be caused by the anit-viral programmes? or is ther something nasty at work here? I do know that the USB plugs had stopped working a few months ago, but I thought that was due to driver issues whihc I was goin to correct..if that info helps. Thanks in advance for eny help provided

Hardware failure doesn't necessarily refer to dropping the laptop or spilling liquids onto it. It refers to the end of the life of a particular component, which would then need replacing. Laptops are not made to last forever. Everyone knows that the only thing that lasts "forever" are diamonds.
Now back to your situation, you said that the IBM screen doesn't show up. If you look very closely to the LCD while booting up, are you able to see anything?
Message Edited by ortegaluis on 04-06-2009 08:26 AM
\\ I do not respond to PM regarding individual tech support. Keep discussions in the forum for the benefit of others //

L512 Wont Boot , Splash Screen then stuck blank screen and Fan in full throttle

I was using the laptop, then it went to suspend mode due normal timeout.
When it came back, the fan start to spin full throttle but it was functionating beside that, normally.
I restarted but then it never boot again.
This is the process where it gets stucked
Boot to Splash Screen, Beep, then a black screen and the fan start to spin at full speed.
(In the post in diagnostic mode, shows no error, pass the memory check, shows the info of the processor )
I tried this:
Retired Hard Disk,
Press 60 Seconds (Reset BIOS) - without battery and power cord
Press 10 times the power button an then 30 seconds -- without battery and power cord
Visually there is no damage in the usb ports, maybe i will need to disassembly to get a better view to check if there is a short somewhere.
With this symptoms , what should else i try. Could be a memory issue?
Thanks for any help you can provide me.

Thanks to the Mod!
It happens that if i wait for about 30 secs, then it will boot up, asking a proper boot media.
I was testing it and was workiing fine, except for the Fan working at full speed, Not suspending or shuting down or Hibernate. Only blinking power button led. So a rude disconnection /Battery Extraction needed to acomplish full shutdown.
But Now in the bios diagnostics splash shows
2201: Machine UUID is invalid
The bios shows only 0s in the uuid section.
i was looking for some imformation about this problem, and i found tah can be solved using some kind of floppy for servicing the laptop.
I ve already downloaded a copy, Havent tried yet, But plan to do some test. as soon i can get some spare time.
It appear tha some comand will let me regenerate the UUID, and with some luck, reflashing the bios will solve my problem.
I'll update as any new steps performed

Windows Vista Wont Boot!! HELP!!

Hello -- I have owned and Acer Aspire M5641 for 4 months with Windows Vista Home Premium preloaded by Acer.
I started having problems with random shut dows, restarts, blue screens. The last blue screen was 0x0000007B. I couldnt get past it, not even in safe mode. So I emailed Acer Support (apparently I have to pay to call) and explained the problem to them, asked for help. They told me to do a System Restore back to Factory Defaults.
I went ahead, completed that and now when I turn on the system I get the Acer splash screen, and then a black screen "Windows Boot Manager" that says: Windows failed to start. A recent hardware or software change might be to blame. Well isnt it setting back to factory defaults, How can there be a software/hardware problem? Anyways, it continues to say : To fix the problem insert installation disc and restart computer. If you dont have this disc, contact the computer manufacturer/system administrator.( I have contacted Acer, they are no longer responding to my pleas for help. I refuse to call and pay $300 for them to probably decide not to help me anyways.) The screen also says,
File: \windows\system32\ntoskrnl.exe
Status: 0xc0000221
Info: Windows failed to load because the kernel is missing or corrupt.
It also gives me an option instead of loading Vista (which I cant) to use a tool: Windows memory diagnostic tool which comes up with, status: Hardware problems were detected, to identify and repair those problems, contact your system administrator/computer manufacturer.
I have tried to contact Acer, thus far they havent helped/responded. I tried booting from a Vista Recovery CD, but that was of no help either.
Can I use a Recovery DVD from another computer manufacturer? (a friend has one from HP) Or is there a way to get a Vista install disc from somewhere? Without buying new from store. I have the product key from the preloaded version that came on the computer.
Any Ideas/Suggestion would be greatly appreciated!! Thank You!!

From what I could find on your particular error code, it appears that the computer had an error as a result of a "INACCESSIBLE_BOOT_DEVICE". Microsoft support can associate that error with a boot sector corruption possibly as a result of a virus. I would possibly lean towards corruption and not a hardware issue because the computer is only 4 months old. Still, to remove the possibility of a failing hard drive, I suggest you bring the unit into your nearest Geeksquad® and have them run diagnostics under the manufacture warranty. Inform the Agent of what you were doing before the error occured so they might be able to give you tips on how to prevent it. But in your current situation, I would suggest reloading the operating system after talking to an agent in a store who can better examine the computer. Recovery discs are unique to your computer and recovery discs from a friend's HP will not work. Call Acer and they should not charge you to inquire about getting a new set of recovery discs. Recovery discs are generally $10 - $30. As an alternative, go to Acer's support site (http://www.acerpanam.com/synapse/forms/webpage.cfm?website=AcerPanAm.com/us&siteid=7293&areaid=7) and order the dics from there. Agent Kevin - CIA Precint 00135
Agent Kevin - CIA Precinct 135

HT1338 Wont boot (black screen)

Hi my mac are really slow when it boots, some times i get a black screen.
The hardware starts but no boot and the screen remains black.
Pls help
MacbookPro 17" 2009. OSX Leopard
I have reinnstalled my mac one day ago but got the same problem

Hello Fredrik,
Boot off your *original* Install Disk while holding down the *d key*, (not c key), then run the extended Apple Hardware Test. Some disks require you to use the Option key at bootup to select AHT. Some models have a separate AHT CD. Some have it on the Disc #2.

GF615M-P33 - 3 beeps and it wont boot (black screen)

Moved to https://forum-en.msi.com/index.php?topic=133091.0 with more information
Thanks

Hi there!
My computer broke down a couple of week's ago and i have been using my laptop meanwhile.
Now i finally got some new parts to my computer.
So the current computer:
AMD Athlon X2 250, 3,0 ghz, AM3, 2MB, 65W
MSI GF615M-P33, Socket-AM3, m-ATX, GeForce 6150se, DDR3, SATA II, GbLAN, PCI-Ex16
Sahpire Radeon HD 4670 512MB GDDR3 PCI-Express 2.0, DVI-I, native-HDMI, HDCP, Lite-Retail
Kingston ValueR. DDR3 1333MHz 4GB, CL9, Kit w/two Matched ValueRAM 2GB DDR3
Samsung HD501LJ, 500GB, 7200rpm, 16M
Windows XP Pro 32 bit, right now, will upgrade later to Windows 7 Ultimate.
Huntkey Delcato PSU-422 450W DC Output: "+5V=35A(RED), 12V1=15A(YELLOW), +3.3V=30A(ORANGE), +12V2=17A(YELLOWBLACK), -12V=0.5A(BLUE), +5Vsb=2.0A(PURPLE), PG(GREY)
So the problem is that when i inserted all of my components and then just went to boot it, it gave me 3 beeps and a black screen.
My flatmate has the same motherboard and i tried the RAM, CPU and Video card on it, and it worked fine with one beep and i got a screen and came to BIOS.
I tried his RAM, CPU and Video Card on my motherboard and it still gave me 3 beeps and no screen.
So i have no clue how to troubleshoot anymore.
Tell me if you need anymore information
Please help me!
Thanks in advance!!

P6N SLI V2 wont boot, blank screen

Hi, Ive just baught on eBay the MSI P6n SLI V2 mobo and i got it unwrapped it carefully as you do, took out my Abit P35 Pro and wacked this new board in (i want SLI so this was the best option with my budget (as the Abit board only supports Crossfire (and at a appalling x4 speed) so ive installed it all and ive put all the wires in following the instructions and it boots up perfectly, making all the normal sounds.
Now heres the problem... i have only 1 G card atm (lending the other out to someone) so i put it in NoN SLI mode, and i jsut get a blank screen. ive tryed other cards, allways a blank screen, and the cards all work in other pcs.
The cards i am trying to put into it are duel Geforce 8800 GT Fatal1es (1gb DDR2) and i have also tryed it with an ATI Radeon X 1860 (or something) but to no avail.
I have flashed the CMOS and tested to see if it was my RAM (Corsair Duel channel 4gb DDR2 800mhz (2x 2gb)
nothing happened...
so am i going to have to get my money back or is there something i havent done???

>> Posting Guide <<
You have not provided enough info to help you. Please provide CPU model and PSU model and amps for +3.3V, +5V & +12V.
"I have flashed the CMOS"
What do you mean by that? You 'cleared CMOS' or 'flashed BIOS'? Two entirely different things.

Neo4 Wont boot.. no screen..HELP

Similar Messages

Maybe you are looking for