Netconnection is not working on Windows7

Hi,
We've ran into an issue with one of our AIR projects:
We have two tandalone chat clients that connect using this tutorial: http://www.flashrealtime.com/local-flash-peer-to-peer-communication-over-lan-without-cirru s/
Both run and connect perfect on windows XP.
When we install both of them on a Windows 7 system nothing works. They don't get connected to one eachother.
The only difference is: we connect to 127.0.0.1:30302 instead of the ip mentioned in the tutorial.
But since this works fine on XP, we expected it to work on Win7
Could anyone help us out on this one?
Thanks!
Regards
Mario

Hi Mario,
Could you send me ([email protected]) your built app so I can give this a try on my systems?
Thanks,
Chris

Similar Messages

NetConnection.proxyType not works

Hi,
I need a solution for this: when the port 1935 is closed, the NetConnection switch rtmpt (port 80). The NetConnection class built in function: proxyType="HTTP" not works or I use not rightly.
In the FLVPlayback class works this function, but I don't know how...
Please help me!
Thank's!

Thank's for the patience:-)
Say if 1935 is not blocked - your rtmp connection is going through fine? It's fine
Now when 1935 is blocked - if you try rtmpt directly does the connection go through. It's fine, but much slower compared to rtmp: connect, sharedObject read-write, etc...is it normally???
if you don't set up proxyType property at all - what results do you see. The rtmp not works, but the rtmpt works. (if port 1935 closed)
Also have you configured FMS to listen to 80? Yes.

Airport in bridge mode not working in Windows7

Hi everyone,
Last night as I was browsing the web on my iPad the internet stopped working...I am using an Airport Express router plugged directly into the wall socket of my apartment which was configured by the ISP.
I have been using this config for the past 7 months with no issues but last night it just stopped working and the yellow indicator started flashing.
I went into Airport utility and it tells me the Double NAT problem has been found (maybe the ISP changed something?)...and they suggest to change the Airport configuration to Bridge Mode ... said and done...now the Internet works fine under OSX and on my iPad but it does not work anymore in Windows 7.
Some of my family uses Windows 7 for some very specific apps and now it's just dead, internet does not work anymore.
Also, in OSX / iOS I didn't make any changes, I just changed the Airport configuration to Bridge mode and it worked right off the bat.
Has anybody else confronted such problems before ? If so, what would be the best way to fix this ?
Thanks!

" I tried trunk port also but it got disabled" <----- if your L2 config is not correct, nothing will work.
What is the setup on the switch ? Trunk or access vlan ?
What is the status of the interface ? up ? down ?
Do you see something in your arp table ?
Gilles.

TX2500Z touchscreen does not work after Windows7 upgrade from HP specific to S/N, etc on laptop.

My TX2500Z touchscreen does not work after I upgraded to Windows 7. I cannot find any support or drivers, etc. to fix. I bought Windows 7 directly from HP specific to my P/N and S/N on my TX2500Z. Any help? Thanks.

after 2,5 days (spending half a day within the apple shop as well with this problem) i have it all back on track.
i did a lot of different things: trying to remove and reinstall iPhoto; did a SL installation over the old SL I had on my HD; backing up all the data of course before and reformatting my HD and installing a new clean SL version on it + a new clean version of iLife9 with all the updates and than I migrate with migrate assistant all the data and setting with time machine back onto it, but all this didn't work, because it also migrated the error/bug through time machine with it.
so at the end i just installed a brand new, clean SL version on my hard drive, than I did the updates and put all my data, photos, docs, movies, mail, bookmarks, music, etc manual back into the system (drag and drop from my external HD, where i had an exact copy of my internal HD) and did all the settings again in all the different programs.
the only thing i used migrant assistant with time machine for was for the programs. it seems to work now all fine and i even got more free space on my HD, because some of the old stuff i always carried with me but i never used, i didn't take over.
basically everything is clean now. At least i hope and works fine. touch wood!

DV9930US Internal Microphone not working (Vista & Windows7)

Hi,
I've had my DV9930US for awhile, but up until recently, I haven't used either the webcam or the internal microphone.
I'm preparing for a trip, so I thought I'd see if I could get something like Skype setup, but I'm finding that the internal microphone doesn't seem to work (doesn't hear anything). Audio output seems to work fine, and, also, if I plug an external microphone into the jack in the front, under the keyboard, that seems to work... it's just the internal microphones (there are two, I think, at the top of the display, surrounding the webcam) that are not working ...
Everything seems to be ok in Device Manager. Under "Sound", I have "Realtek High Definition Audio". The driver is dated 1/15/08, V6.0.1.5548.
I've tried testing with Sound Recorder, and I've also tested using the "Configure Microphone", but it never shows any bars, and the file that Sound Recorder recorded is basically silent.
I still have the original Vista Home Premium on this machine and also Windows 7 Ultimate (I dual boot), and even the original Vista seems to have the same problem.
I've seen some posts here with problems with G60s, but no resolutions, so I was wondering if anyone might know what
the problem might be?
Thanks!
Jim
This question was solved.
View Solution.

Hi,
For the record, I finally found the problem.
In the DV9930US, there's a small (1"x1") PCB called the "power button board". This has the power button, and 3 pinned connectors, plus a flat cable connector.
The microphones in the display bezel connect to one of the 3 pinned connectors, and the flat cable goes, I think to the actual audio board.
I had replaced the microphones, which didn't fix the problem, so I bought a replacement power button board, which luckily, came with a new flat cable.
It turned out that the original flat cable going from the power button board to the audio board was bad.
I replaced the flat cable, and then the internal mics worked.
Jim

X1 Carbon 2014 Function keys not working in windows7

Hello.
I have a brand new X1 carbon(model: 20A7-005KMD) that was installed with our company image, running windows 7.
Alle drivers in device manager has been installed, and system update is updated.
The carbon has the "touch" function keys and they only partly work.
When booting the computer i can swap between the different functions, but when i get into windows, its is "stuck" with only the options F1-F12. The F keys work, but i cant change settings by pressing the FN key on the left side og the touch display, and get sounds/brightness settings etc.
as said, this works just fine during the boot.
Any ideas what can be causing this and even more important - a fix?

Hi Guys,
We are currently having the same issue on the X1 Carbon 20A7 models (20A7000LAU). In BIOS or during boot the function changing works without issue (limited to two (2) function screens how-ever), it stops working once you log in. If you then lock the computer you can change the functions, but then once you unlock the device, it stops working.
When the drivers are installed and the device is restart we get the above behaviour, if we uninstall the drivers the function keys will function as expected till the device is restarted. This is very strange behaviour.
On a device received by Lenovo there are 4 function changes/screens in total, we can only make two work temporarily as listed above. We have tried the following.
1. MDT 2013 Delivered Windows 8.1 x64 image image. All drivers/software components installed from the lenovo website. We receive above issue and cannot resolve by uninstall/reinstalling.
2. Vanilla Windows 8.1 ENT x64 image installed from Microsoft Volume Licensing portal, installed all drivers supplied from the Lenovo Website. The same behaviour is seen as above and is reproducable.
3. We have als compared all drivers/software installed on the factory supplied model to a manually built device, still the above behaviour is witnessed.
4. We have manually exported drivers from the X1 Carbon device from lenovo and injected them into the vanilla Windows 8.1 ENT or PRO newly imaged device, still the same behaviour above.
Please let me know what I'm missing, I'm certain this is a bug in the drivers for this model.
Regards,
Nic

Lumira 1.17.1 is not working in windows7 32 bit OS

Hello Experts,
We recently upgrading the lumira desktop enterprise edition from 1.15 to 1.17.1 version in windows 7 SP1,32 bit OS.(4GB RAM)
We have installed 32 bit lumira desktop version with admin rights and installation was done without any errors.
When we click on SAPLumira.exe file,there is no action and nothing happen and we are not able to get the lumira screen.
Need your suggestions.
Regards,
Vinay

Hi,
is the problem systematically reproducible on all 'upgraded' workstations?
Are you able to try Uninstall SP15, then Install SP17 in 2 steps to see if that makes any difference?
before re-installing, additionally I would recommend deleting these locations (and their contents):
C:\Users\<user>\.sapvi
C:\Users\<user>\AppData\Local\SAP\Lumira
first, shut down any other windows applications, then try 'run as admin' when starting/launching the application.
this could well be a platform/resource problem. 32 bit is not optimal for Lumira, hence the proposed move over here: http://scn.sap.com/message/15190775#15190775
Regards,
H

Media Manager not working in Windows7

I installed media manager a few months ago................. and it seemed to work OK for a couple of weeks. Now i get a pop up saying Media Manager has stopped working ( checking for a solution ) a problem caused the program to stop working correctly. Windows will close and notify you if a solution is available....(which it never does).............. Why cant you guys fix this **bleep**@ This has happened multiple times before......too amny time for me to count...... i wind up uninstalling and reinstalling with the same outcome??? Come on NOW.

lmun wrote:
I don't think you actually read the post above. I have the exact same problem and have uninstalled/reinstalled on a Windows 7 (64 bit) system. It loads the first screen for a few seconds and then demands to close and posts the following:
Problem Event Name: BEX
Application Name: Verizon Media Manager.exe
Application Version: 9.5.67.0
Application Timestamp: 4e98682f
Fault Module Name: Avance.dll
Fault Module Version: 6.0.19.0
Fault Module Timestamp: 4cc5a04b
Exception Offset: 00041ae6
Exception Code: c0000409
Exception Data: 00000000
OS Version: 6.1.7601.2.1.0.256.48
Locale ID: 1033
Additional Information 1: 1ead
Additional Information 2: 1ead641666d0da3ef93d23ec2c5e4612
Additional Information 3: 7872
Additional Information 4: 78728a79bda53a68145a89f6fb03040f
Is the program actually ready for prime time???
I'm running it on a Windows 7 64-bit system and it works just fine. Have you unistalled it and tried to reinstall it as a full administrator? FYI there is an unistall program in the Verizon start menu folder, but you should also try doing it via the programs and features control panel.

Help is not working in Form Builder 6i

Hi all,
I'm using Forms builder 6i in Windows7 system. When i go to Help menu and click 'Form Builder Help Topics' a error message is coming.
I've reinstalled it many times. In Windows XP system it's working fine. Why it's not working in Windows7?
Any suggestions??

Check this:
http://support.microsoft.com/kb/917607
Regards

Hp deskjet 5650 is not working with windows 7

i've connected the printer to a new lenovo laptop.
the printer shows in the devices & printers as default but will not print.
the icon appears as though it should but says "0 documents pending".
what am i doing wrong?

hp laser printer p1077 is not working in windows7 ,32 bit OS... all the installation process were successful but when the page is asked to print its not printing... even the test page is not printing so please help me fix this problem please...thank you.. I think This printer no support to Windows 7 ???? Please confirm this or advise how we can solve this problem Becoz i don't know why this problem is coming all thing are fine. Deepak Joshi

Hide mouse cursor when typing is not working in IE11 Windows7

Hide mouse cursor when typing is not working in IE11 Windows7 - I saw a post that devs were looking at this in 2011? Slow progress huh?
This is really annoying when you have to move the cursor to see what you are typing...

Hi,
Please first make sure that Mouse Properties\Pointer options\Hide pointer while typing is ticked.
If this option is already ticked, then try following steps to troubleshoot:
Update the driver for the mouse to get the best performance.
Choose a different cursor as Rob said for a test.
If this issue occurred recently, check if you have any newly installed programs or IE add-ons which cause this issue, you can test this in no add-ons mode, click start button, type "internet" in the search box, choose "internet explorer (No add-on)".
* I test in My IE, I have Hide pointer while typing checked, and in some typing boxes in IE the cursor will hide automatically, while some are not, but I think it's not an annoying issue for me.*
Regard
Yolanda
TechNet Community Support

Acrobat Pro XI not working at all in Windows7 64bit - tried everything

I am using Acrobat Pro XI not working at all in Windows7 64bit - tried everything. About a month ago I built new computer. Acrobat worked fine. In last week it started not producing PDFs using Save As and would crash when processing scanned document. So I redownloaded exe file, used the acrocleaner to erase existing program, and reloaded Acrobat Pro XI.
No the program will not start at all. Freezes when opening by clicking PDF file or by opening program icon.
plz help

Hi dufflebag123,
Please try the following basic troubleshooting steps:
> Enable the hidden Admin Account on Windows 7 ( Ref : http://www.howtogeek.com/howto/windows-vista/enable-the-hidden-administrator-account-on-wi ndows-vista/ )
> Disable all Non-Microsoft Startup Services. (Ref : http://helpx.adobe.com/x-productkb/global/disable-startup-items-services-windows.html )
> Disable all the Antivirus softwares like CA, Norton,Mc Afee etc. temporarily from the computer.
Reboot and try installing in the new enabled Admin user account and check.
Regards,
Rave

Hi,my name is Hemanth.Im using ipod touch and my ipod is not detecting in itunes but detecting in my computer.Im using windows7 os.I tried the troubleshooting process given in web but still it not working please help me.

Hi,my name is Hemanth.Im using ipod touch and my ipod is not detecting in itunes but detecting in my computer.Im using windows7 os.I tried the troubleshooting process given in web but still it not working please help me.

Did you try everything here:
iOS: Device not recognized in iTunes for Windows
Then try a different computer to help determine if yo have an IPod or computer problem.

NetConnection httpIdleTimeout on Android not working

Hi all,
I connect to web services using a NetConnection. This works very well, except on Android when there is no network connection.
Even though httpIdleTimeout is set to 5000ms, making a call with NetConnection will not respond for about 7-8 minutes, until finally an error event is received.
NetStatusEvent, HTTP: failed
I'm using AIR 15 on a Nexus 7, but same result on a Galaxy Nexus (and others).
Cheers,
Peter

I am having essentially the same problems as those described by J_Miller. This is my 3rd Galaxy S4 (which I love). I broke the first two. I have not had ANY problems with the first two S4s. I just activated my 3rd (new) S4 last night (Sat/4/4). Thought all was good. Today I discovered the problems that J_Miller describes. All phone functions work fine, except for calls. With calls to/from others and with chk'g voice msgs, the phone acts as though calls are taking place, but I hear no sound. People on the other end of a call also hear no sound.
I noticed a "headphone" icon at the top of my phone. I have never seen that before. I don't own headphones. I've never used or installed anything to do with headphones on my phone. I've never listened to music on any phone I have ever owned, ever.
The icon leads me to suspect that my phone thinks I have a headphone installed on the phone and that all sound is being sent to the headphones.... rather than through the device itself, speakerphone, or Bluetooth headset. Also, when I pull down the notification window, there is a menu bar that states: "Recommended apps (Earphones)". I have never seen this menu bar before. It includes icons for: Messaging, Settings, Google Maps, Contacts, and AccuWeather.
Since I just activated this phone, I was planning to do a factory reseat and start over. But after reading J_Miller's thread, I'm afraid that solution won't work.
Any thoughts would be appreciated.
Thank you!
GRuss150

What if sync with new computer does not work. logical connection to old with WindowsXP, 32 bit version of iTunes. New is Windows7 with 64bit version

What if sync with new computer does not work?
logical connection to old with WindowsXP, 32 bit version of iTunes.
New is Windows7 with 64bit version

Syncing to a new iTunes library or computer will erase your iPod. Only if you back up your iPod manually before syncing, you can restore your device from that backup again. A manual backup does not include the sync process.
Do this:
Disable autosync in iTunes, connect your iPod to your new computer and right click on it in the device list and choose backup. iTunes will backup your iPod without syncing.
Transfer your purchases the same way, choosing "transfer purchases" this time.
When you connect your phone for the first time, all media content will be erased. But you can restore your settings and app data from your manual backup afterwards.
Don't forget to set up at least one contact and event on your new computer to be able to merge calendars and contacts when you sync the iPod for the first time.
Music is one way only, from the computer to your device, unless you bought the songs in iTunes and transferred your purchases.
There is 3rd party software out there, but not supported by Apple, see this thread: http://discussions.apple.com/thread.jspa?threadID=2013615&tstart=0
About backups and what's saved: http://support.apple.com/kb/HT4946
How to back up and restore:http://support.apple.com/kb/HT1414
How to download apps for free again:http://support.apple.com/kb/HT2519
Saving other data is also described here. How to back up your data and set up as a new device
If your iPod can't be recognized by Windows, try these tips: iOS: Device not recognized in iTunes for Windows

Netconnection is not working on Windows7

Similar Messages

Maybe you are looking for