NetFlow/NetQOS on a 3750x switch
Hello, I have 3750x running c3750e-universalk9-mz.122-55.SE5 layer 3 capable. Im trying to enable net flow on the switch but for some reason the flow commands dont appear to be available in config t mode. Are there some other global commands that have to be enabled first in order for the netflow commands to be available or is it the image that doesnt support netflow?
Andy
Thanks Rajeevsh,
I ran the command I got the output below, i do see ipbase in there but dont know if that means its active..
Maybe it needs to have IP services as you pointed out..
Thanks for looking at this..
andy
inmu-tcs-inet1-sw#sh license all
License Store: Primary License Storage
StoreIndex: 0 Feature: lanbase Version: 1.0
License Type: Permanent
License State: Active, Not in Use
License Priority: Medium
License Count: Non-Counted
StoreIndex: 1 Feature: ipbase Version: 1.0
License Type: Permanent
License State: Active, In Use
License Priority: Medium
License Count: Non-Counted
License Store: Evaluation License Storage
StoreIndex: 0 Feature: ipservices Version: 1.0
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
License Priority: None
License Count: Non-Counted
I also ran it on another 3750x where netflow commands seem to work and the output is different..see below:
dmz-srvdist1a-sw#sh license all
License Store: Primary License Storage
StoreIndex: 0 Feature: ipbase Version: 1.0
License Type: Permanent
License State: Active, In Use
License Priority: Medium
License Count: Non-Counted
License Store: Evaluation License Storage
StoreIndex: 0 Feature: ipservices Version: 1.0
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 8 weeks 4 days
Evaluation period left: 8 weeks 4 days
License Priority: None
License Count: Non-Counted
Similar Messages
-
10Gb module uplink for 3750x switch issues
Hi All,
We build a network consists of 3 x 48 ports 3750X switches and this network is uplink to the Core with 10GB uplink.
We bought 3 x 48 port 3750x with 10GB modules plus enough10GB SFPs.
The problem is for the 10GB module , we can only have 2 x 10GB SFP connections or 4 x 1GB sfp uplinks.
How do we get around with the 3rd switch which need an extra 10GB uplink to the core ?
we do not want to buy another 3750x switch and stack to the third switch to give it more 10GB ports.
Any solution is much appreciated.
Thanks
PLeHi,
Can u shar the BOM which includes 10Gig module part code and a proposed digram which u wanted to deploy.
Vivek -
Cisco 3750X Switch, Observing change in Running & Startup Config
Hi,
I have a cisco catalyst 3750X switch running with c3750e-universalk9-mz.152-1.E1.bin, where I'm able to see the running configuration & Startup configuration on the device is not in Sync even after saving configuration to the NVRAM.
Startup Configuration is the one which is required for my network to work properly, but as I'm able to see running configuration is adding some of the configuration which is not actually required in the template. Can anyone help me to get this issue addressed.
Configuration attached.Can you try this command:
Switch#copy startup-config running-config
And then check if you are still face the same issue?
HTH
Regards
Inayath -
Cisco 3750x switch. Turning off a port at night
Hi everyone,
I have a question regarding power management for the Cisco 3750x Switches. Is it possible to power down switch ports
automatically at a specific time and if so how. I would like several Ports to be powered down between 2 and 3 o clock at night.
Can anyone tell me how i can realise this? (these switches have Energie Wise capabilities)
I hope to hear from you soon.
Thanks in advance!
Kind regards,
Wouter Platteeuwfew things to try:
Go to your email setup, go to the account in question, go to filters, Check the box that says "do not forward messages to the device" Set this back to the default if this doesn't work.
Something else: try using the blackberry firewall
http://btsc.webapps.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB23877
I think this will block all email though, but you can take a look at the options.
Please click the Thumbs Up icon if this comment has helped you!
If your issue is resolved, please click the solution button on the resolution!
Every BlackBerry should have BlackBerry Protect, get it now! | Follow me on Twitter | Bring Back BBM Music! -
I have a 3750x switch stack of three switches.
One of the switches has reset 2 times and rejoined the stack.
Everything appears to be working fine except that every port light is flashing green light.
No one touched mode button.
Is this a warning of some kind?Leo
Thanks again for the help.
I was also showing this issue to another source and he suggested exactly what you said above."It looks like the switch is having problem keeping power"
The people at the site say there have been no power surges but I agree that is seems like power is the problem.
Switch 2 is the master now so I cannot do a session 2.
switch 1 was the original master and it has only been up for 5 days.
KBCUK2Stack01#sess 2
%ERROR: cannot redirect to itself
KBCUK2Stack01#sh ver
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(1)SE3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 30-May-12 13:41 by prod_rel_team
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
KBCUK2Stack01 uptime is 1 year, 37 weeks, 2 days, 2 hours, 7 minutes
System returned to ROM by power-on
System restarted at 10:08:26 GMT Sat Nov 24 2012
System image file is "flash:/c3750e-universalk9-mz.150-1.SE3/c3750e-universalk9-mz.150-1.SE3.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: ipservices
License Type: Permanent
Next reload license Level: ipservices
cisco WS-C3750X-24P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1641Z06H
Last reset from power-on
9 Virtual Ethernet interfaces
1 FastEthernet interface
84 Gigabit Ethernet interfaces
6 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : E4:D3:F1:BF:C5:00
Motherboard assembly number : 73-12551-06
Motherboard serial number : FDO164109FB
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C3750X-24P-E
Daughterboard assembly number : 800-32727-03
Daughterboard serial number : FDO164013UH
System serial number : FDO1641Z06H
Top Assembly Part Number : 800-31325-03
Top Assembly Revision Number : B0
Version ID : V03
CLEI Code Number : COMJR00ARC
Hardware Board Revision Number : 0x04
Switch Ports Model SW Version SW Image
1 30 WS-C3750X-24 15.0(1)SE3 C3750E-UNIVERSALK9-M
* 2 30 WS-C3750X-24P 15.0(1)SE3 C3750E-UNIVERSALK9-M
3 30 WS-C3750X-24 15.0(1)SE3 C3750E-UNIVERSALK9-M
Switch 01
Switch Uptime : 5 days, 15 hours, 12 minutes
Base ethernet MAC Address : E4:D3:F1:DC:FC:00
Motherboard assembly number : 73-12530-06
Motherboard serial number : FDO16410YN5
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C3750X-24T-E
Daughterboard assembly number : 800-32727-03
Daughterboard serial number : FDO16410QPM
System serial number : FDO1641X18T
Top assembly part number : 800-31327-03
Top assembly revision number : B0
Version ID : V03
CLEI Code Number : COMJV00ARC
License Level : ipservices
License Type : Permanent
Next reboot licensing Level : ipservices
Switch 03
Switch Uptime : 1 year, 36 weeks, 6 days, 2 hours, 19 minutes
Base ethernet MAC Address : 30:F7:0D:CD:29:80
Motherboard assembly number : 73-12530-06
Motherboard serial number : FDO16281H00
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C3750X-24T-E
Daughterboard assembly number : 800-32727-03
Daughterboard serial number : FDO16281FSD
System serial number : FDO1628V1J6
Top assembly part number : 800-31327-03
Top assembly revision number : B0
Version ID : V03
CLEI Code Number : COMJV00ARC
License Level : ipservices
License Type : Permanent
Next reboot licensing Level : ipservices
Configuration register is 0xF -
3750X switches - get the port duplex by SNMP
Hello,
I'm trying to get the 3750X switch port duplex state by SNMP. It looks like the only available OID is portDuplex, but this is for operational duplex, not the admin duplex.
So, if the portDuplex shows full(2) for a port in SNMP, you can't tell if the port is hard set to "full" or auto-negociated to "full".
As oposed to the CLI, where a "sh int status" command will show "full" for the hard-set ports and "a-full" for ports that auto-negociated to full.
For port speed, it looks like "portAdminSpeed" OID does the job.
So, my question is, using SNMP, how can I tell if a port's duplex is hard set or not??
Thank you,
LauraHi,
How to check whether its stack cable problem or stack port problem on respective switch.
Most of the time the issue is the stack cable and not the port. Try inserting the cable all the way into the slot. With 3750x switches the slots are narrow and some times you need a flash light to look to make sure the cable is in all the way.
If I change the stack priority on switch 2 and switch 1 , do I need to reboot whole the stack so that new priorities for switch 2 and switch 1 would change to new values.
Yes, reboot the entire stack, after the election switch 2 should be 14 and switch 1 13.
I would correct the stacking cable issue as well before rebooting.
HTH -
Enabling Netflow on Production 6500 Core switch
Hi All,
I am looking for a little expert advise regarding Cisco Netflow. For monitoring I need to enable Netflow feature on 6500 core switch or 6500 load balancer with CSM module installed, but I am just concern about the CPU hits on the devices. we are not using any dynamic routing protocols. Can someone please advise how will it effect on the local resources when using Netflow? Is it fine if I enable this feature on these devices in production?
Thanks in advance,Hi Mudassar,
Enabling netflow will not have a major impact on CPU or memory but you will want to keep a close eye on the switches TCAM utilisation. Features like netflow, TCP intercept and WCCP can use resources from “NetFlow TCAM Table”.
Use the "show mls netflow table-contention detailed" command to monitor TCAM utilisation.
Regards
Brett -
Device Package for 3750X Switches
Is there a Cisco Works Device Package for the new 3750X switches? Just bought
159 3750X-48PS-S switches to go with over 1000 3750G switches.Thanks for the correction - I missed them when checking my earlier post.
3750X's ARE on both the LMS3.2 support list and the LMS4.0 / 4.01 support lists.
As you mentioned, applying the latest device support package will add them to the fold. -
Replace 3750x switches with equivalent fibre models
We are currently using cisco 3750x's as our edge switches in our network (mix of 24 and 48 port switches).
The office is being reconfigured and existing cabling is going to be replaced with fiber.
What Cisco switch would be suitable (similar to 3750x) for gigabit fiber connectivity to desks?
ThanksDisclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Most like your existing 3750X's would be, as noted by Leo, the 3750X-24S. You can also, of course, stack them with your existing 3750X units.
Regarding whether, as Leo suggests, they are "a sure waste of money", well I guess much would also depend on your cabling plant. If your existing edge 3750X are in closets, and there's just a couple per closet, and you're just replacing floor copper, they probably are the most cost effective option.
Unfortunately, they are getting dated, and I see Cisco has recently revised the product page to suggest considering the 3850 (or 3650) series, although those don't have an all fiber model. -
Rate Shaping/Traffic Shaping 3750x Switch Internet Access Circuits
Hello, I have 3750x running c3750e-universalk9-mz.122-55.SE5 layer 3 capable. I have two internet access circuits on the switch both 100Mbps however there subrated down to 14Mbps by the ISP. Id like to rate shape out bound traffic toward the ISP so we dont drop traffic that exceeds the 14Mbps rate.
It appears this can be done at the layer 3 SVI or at the Layer 2 switch port level. Not sure which is the best way? Please could anyone show me the commands for acheiving the rate shaping?
AndyHey Andy,
i believe this is a good point to start:http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/12-2_55_se/configuration/guide/3750xscg/swqos.html#wp1200681
HTH.
Regards,
RS. -
3750x Switch Inter-Vlan routing
Hi
I would just like to find out what feature set the 3750x needs to be able to enable the "ip routing" command.
It currently has the LAN base feature set, which does not have this command.
Can it be done on the IP BASE feature set ? or the IP SERVICES set ?
ThanksHi,
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-3750-x-series-switches/qa_c67-578933.html
As noted here you can do static routing with LAN Base.
Regards
Alain
Don't forget to rate helpful posts. -
How to configure multiple cisco 3750x switches
Hi All,
we recently bought 25 x 3750-48PS switches and need to roll them out with similar IOS and configuration.
I normally get a console to the switch from my laptop and do one by one.
is there a better way or software which can speed up the process ?
Thanks
QlRead this: ZeroTouch SmartInstall
If configured properly you can load the correct configuration & load the correct IOS in 20 minutes. The entire pile in 20 minutes! -
Unable to enable routing in 3750x switch
im unable to enable ip routing in the WS-C3750X-24T-L switch. Tried with SDM prefer routing option but still same issue.
Can some suggest on this?
MOdel: WS-C3750X-24T-L
IOS :flash:c3750e-ipbasek9-mz.122-55.SE5.bin
sh license
Index 1 Feature: ipservices
Period left: 0 minute 0 second
Index 2 Feature: ipbase
Period left: 0 minute 0 second
Index 3 Feature: lanbase
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Priority: Medium
License Count: Non-Counted
regards,
Ezra.Index 3 Feature: lanbase Period left: Life time License Type: Permanent License State: Active, In Use
You don't have the license to run routing. -
Can IPV6 QOS support in Cisco 3750x switches
Hi
I have tried IPv6 qos using class map in Catalyst 3750 switches but the platform is not support.
Can anyone configured the IPV6 qos in Cisco 3750-X switches. Does it support?
Cisco 3750 config
policy-map up
class bwtest-up
police 2048000 128000 exceed-action drop
policy-map down
class bwtest-down
police 512000 128000 exceed-action drop
trust dscp
class-map match-all bwtest-up
match access-group name bwup
class-map match-all bwtest-down
match access-group name bwdown
ipv6 access-list bwup
permit ipv6 2402:xxxx:x:x::/64
ipv6 access-list bwdown
permit ipv6 any 2402:xxxx:x:x::/64
L3(config)#int g1/0/4
L3(config-if)#service-policy input up
QoS: class(bwtest-up) IPv6 class not supported on interface GigabitEthernet1/0/4 ( error)
Please help!interface GigabitEthernet1/0/4
description ##Test LAN-IPV##
no switchport
bandwidth 2048
no ip address
load-interval 30
speed 100
duplex full
ipv6 address 2402:xxxx:x:x::1/64
ipv6 enable
ipv6 ospf 200 area 0
end
switch sw version
Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Mon 03-Mar-14 22:45 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02F00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
Cherry uptime is 6 days, 7 hours, 23 minutes
System returned to ROM by power-on
System restarted at 07:04:50 IST Thu Mar 19 2015
System image file is "flash:/c3750-ipservicesk9-mz.122-55.SE9.bin" -
3750X Switch-to-switch TrustSec(MACsec)
Hello,
I had read about this here and on the others site and I'm not sure if I understand everything good. I want to secure connection between 2 C3750 with TrustSec. The was said that this is impossible without srvice module. Do I try to do this with vlan, trunk and macsec. Is this possibly. What I have to do?This link should help you out-
https://supportforums.cisco.com/thread/2157453
Maybe you are looking for
-
How to convert Web app into a channel?
To whom it may concern, Does anyone know how to convert a Web app into a channel inside the Portal server 6.0? I developed the web app and tried to create a provider and a channel for it, but the Portal server did not recognize the WEB-INF folder and
-
List of users who have access to multiple mailboxes
Hi, I got the list of around three hundred generic mailboxes Please help me with the command which can help me to get the report of all users who has access on those generic mailbox.
-
Quicktime latest version will not install
I Quicktime did not install I have old itunes but got iphone today it requires latest itunes but quicktime will not install. I updated VBScript but stil get error code 2738 Help!
-
Ipod does not respond to computer/Itunes, but reboots constantly.
I have been using the same Ipod since 2/14/2006 (Black 30GB-5th Generation). Never had any problems with it at all. About 4 days ago, I updated to the latest version of Itunes (Ver 7.6.2.9.) and I have been having problems with my Ipod ever since. Ev
-
Host variables in SQL Developer not showing decimal places
I'm a very newbie, taking my first PL/SQL class, so please be gentle! I think this may be a SQL Developer problem, because when I run the same thing from terminal-line SQLplus on my Linux install, it works right. I'm working with a procedure, and pas