Netgear DG834G setup with Airport Extreme Base

Until yeseterday my home network consisted of an ADLS modem connected by ethernet to an Airport Extreme base, to get additional range I have an additional Airport Extreme Base downstairs ( life before ap express). I also have a USB printer in the 1st base - all was good and life was wonderful.
Then..... the adsl modem/router died. It was recommended that I get the Netgear DG834G as it was easy to setup blah blah blah... Long story short it is set up and I do have internet access wirelessly to part of my house - the range is terrible. I would like to use the two airport base stations I have to get acceptable coverage and also to use my printer via the USB again.
Can anyone please tell me how to make the airport bases talk to the Netgear. BTW ... Base #1 is sitting next to the Netgear box so if it needs to be connected by ethernet it is no problem.
Thanks much Susan

You can connect your AirPort Extreme base station (AEBS) to the Netgear via Ethernet. Configure the AEBS so that the option to distribute IP addresses is disabled.

Similar Messages

Creating a bridge with airport extreme (base) and airport express

i am having trouble creating a bridge with airport extreme (base) and airport express. i got the airport express to connect to my network. Airtunes sees it fine. i have an iMac (running Tiger) connected to the airport express via ethernet which i was hoping to get internet on (the iMac doesn't not have built in wireless and i had a spare airport express). now the airport express is no longer visible to the airport setup assistant on that iMac. but, like i mentioned, Airtunes is working fine, and the light is green.
i'm new to the wireless stuff. i am sure i just missed a step. how do i get the iMac to connect to the internet via my airport express bridging to my airport extreme wireless network?
your help is appreciated.

You can do this with the equipment you have. Configure the AirPort Extreme base station (AEBS) to act as a WDS main base station and configure the AirPort Express (AX) to act as a WDS remote base station. That will allow you to use the Ethernet port on the AX.
Unfortunately WDS also causes the available wireless bandwidth to be cut in half.

Printing wirelessly to MacBook Pro with Airport Extreme Base Station

I have an Airport Extreme Base Station that I used to use wirelessly until I got Verizon Fios. The Fios technicians said the base station couldn't be used and so it's been sitting unused for a few months. However, I really, really miss printing wirelessly, and was wondering if it was possible to use the Airport Extreme Base Station ONLY to print wirelessly, and not connect it any way to my internet (I don't want to mess with any of the fios stuff at all).
If it's not possible, is there any other way to print wirelessly without purchasing another product or special printer. I have a HP c4480 printer.
Thanks!

If your printer has a USB cable the easy way to go about this in my opinion is to plug that USB cable into your Extreme base station. I have the Extreme ABS that looks like a flying saucer. I plug the usb cable into the port that has the symbol that doe NOT look like this <--> rather it looks like a Saguaro cactus.
My computer then sends print documents to the Extreme via WiFi and then Extreme sends them to the printer via the USB cable.
If your Airport status is not showing in the Mac's menubar go to system Prefs/Network/Airport and check a little box so it will show up in the menu bar.
Now if your Extreme is plugged in the wall and powered up your Mac should be able to find it. Click on that menubar item for Airport and scroll down and select your Airport Extreme. I don't know for sure what its name will be. It should still be the same as it used to be when you used it last.
Now try printing a simple document. In the print dialog window you should be able to select what printer you want to use. If your new Extreme printer is listed select it. You may need to click on Print & Fax and figure out how to select it from there, and choose it to be the new default printer.
I think this info will do the job. Whenever you want to print you have to go to the Airport icon in the menubar and change your airport connection from your Verizon stuff to your Extreme. Then of course you have to change back when you are done. That is why it would be great to toss the Verizon WiFi radio out the window and just plug your Verizon modem into your Extreme WiFi radio transceiver (router). But I understand you cannot deal with that at this time.
If this does not do the job, if I have missed something, I will bet you 5 bucks that you can still figure it out if you just look at any error messages and/or look at the Print&Fax prefs and the Print dialog windows etc. and see what I may have missed. Maybe you have to go to SystemPrefs/Sharing and allow your printer to be shared. I don't think so. The way I figure any of this stuff out is to just look at stuff and think and try things and see what happens.
Your Verizon setup should be something like this.... a cable comes into your house and goes to a 'modem'. From there and ethernet cable (CAT-5 cable) goes from that modem to your Verizon router (WiFi radio transceiver).
As for getting rid of the Verizon router, when you are ready to give it a go, simply unplug the ethernet cable (it has a plug on the end that looks like the kind of plug that telephones use to plug into the wall, except it is a bit wider, but still has that same kind of snap-lock tab) that comes from the Verizon modem (the modem has the heavy round cable and probably many blinking lights) and plug it into the Extreme. Mine has an icon on the Extreme that is many dots in a circular pattern.
At this point you may have to unplug the Verizon modem form the wall AC power and the Extreme also. Then plug them back in, wait a minute, go to your Airport icon on your Mac menubar, Select Extreme and start surfing the web.
It really is that simple with a Mac. Maybe Verizon has found a way to make things difficult but my guess is no. Any password should be taken care of in your Airport Setup Utility program. It should be the same password(s) as you used before when you used your Extreme.

How do i set up time capsule to work with airport extreme base to extend wireless network?

i have a airport extreme base, how do i set up a time machine to extend the wireless network i have with airport extreme? i have also 3 airport express's connected to the same network to extend my wifi all over my house. thanks in advance.

Much better graphics, thanks.
You can leave the Time Capsule connected by Ethernet from the Linksys and configure for a "roaming" network as mentioned previously.
To do this, open AirPort Utility - Manual Setup
Click the Wireless tab below the icons
Wireless Mode = Create a wireless network
Wireless Network Name = Same name as the AirPort Extreme
No check mark needed next to Allow this network to be extended
Radio Mode = Same setting as the AirPort Extreme
Channel = Automatic
Wireless Security = Same setting as the AirPort Extreme
Wireless Password = Same password as the AirPort Extreme
Confirm Password
Click the Internet icon, then the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings and allow the Time Capsue to restart
Then power down the entire network
Wait a minute or two
Start the modem first and let it run a full minute
Start the AirPort Extreme the same way
Power up the switch
Power up the Time Capsule for a minute
Keep starting devices one at a time about a minute apart
Now, your computer will automatically pick up a wireless signal from either the AirPort Extreme or Time Capsule, whichever device is closer and providing the stronger signal.

Communication errors with airport extreme base station

Please help.
I am able to surf the internet wirelessly on my two macs via my Airport Extreme Base Station. However I am unable to print wirelessly via my new HP printer connected to the USB port on the base station.
More worryingly I am unable to use Airport Admin Utility, Airport Set-Up Assistant or Airport Firmware Updater. Whenever I try to use one of these applications they experience errors communicating with the base station. I wonder if this is related to the printer problem?
I have performed soft and hard resets on the base station in addition to removing the power cord - none have been sucessful.
Can anyone please help me.

I may have a solution. I recently upgraded from an ibook to a macbook pro, and had the apple store "migrate" my files, etc., from one to the other. Got it home, everything's fine, airport conects, no problem. Go to print, can't print, decide to run Airport Setup Assistant to reconfigure (why not ?) and, lo. when it gets to "Network Configuation," I get : "An Error Occured while trying to communicate with this base station." Try all the usual tricks, including hard restart (internet connection is fine throughout), but the set-up assistant couldn't get past that point. Talked to apple support, we ran through all the options. He did suggest wiping the network preferences for airport off the harddrive and starting over, but since I had a good internet connection, I decided to wait.
So here's the thing: I got on Airport Administrative Utitity, clicked "Configure," and then "Network." I know next to zip about advanced options, but I decided to click "Distribute IP Adress" And under "Airport Client Computers" selected "share a single address." I left everything else alone. It reset to to the new options, and then, out of curiosity, I opened up set-up assistant, and TA-DA, I got past the screen I was stuck on, and when the next asked me if I wanted to keep all the same settings, I said yes. I kept selecting "Keep/yes", and then saved or okayed the changes. I then got a message that it would restart base station, I was also configured to print (my printer hp laser 1320 was plugged into the base station for all this), and, yes, it does now print.
I don't know if this is the hard way of doing something that I could have done more easily, and/or if even though I had an internet connection, the base station or the set up was still looking for the ibook. I'm sorry for such a long reply, but wanted to include all the steps I took and the exact situation. Does anyone know if I've endangered my security by checkig the "Distribute IP option ?" This is a home computer. Good Luck and hope this helps someone

Networking with AirPort Extreme Base Station

I am connected to the Internet with an SBC dsl modem, which I have had for a couple of years with few problems. However, I have been having issues networking my Mac G5, 1.8 Mhz machine since I purchased it some time ago.
In the beginning (before the Mac or -- BM as I like to call it) I was using a D-Link DI-614+ router and running a desktop PC and a laptop PC wirelessly with success. Then I bought my Mac (which I dearly love) and introduced it into my wireless network. At first it seemed to work OK. Gradually and occassionally it would lock up while trying to access an Internet site. Often the problem was resolved by rebooting the DSL modem, the D-Link router and all the computers. This would give me up to several days with no problems, but then things would rapidly deteriorate and I would have connection problems again.
I thought that if I bought an Airport Extreme base station, that would solve the problems but again, at first things were fine, then rapidly went downhill. I have worked exensively with SBC dsl techs and we have determined that the problem is not with the SBC network or with their dsl modem.
As it stands now I only get a maximum of a couple of hours of time before the slowing down of the network begins. Some of the error messages I get seem to indicate that there is a problem with the distribution of IP addresses. TCP/IP is set to use DHCP, and I connect by setting PPPoE to my SBC connections settings. "Connect using PPPoE" is unchecked. Location is currently "Automatic" although I have used the connection assistant a number of times in an attempt to get the system up and running.
I have the same problems in interconnecting the Mac with the two PCs that are on my system. In fact this is even more erratic than connecting to the Internet.
I have spent many hours with my limited knowledge of these things trying to resolve these issues but have had no success. I have scoured .Mac and other Internet sources and cannot find any specific solution to this problem. I am at a real loss as to where to go next. I am hoping someone here can help or point me in a direction where I might find a solution.
Thanks,
Don
Power Mac G5 Mac OS X (10.4.7)

Thank you very much for your response. Yes, the Mac is set to use PPPoE and the SBC information is stored there.
Just to clean things up, I removed the PPPoE configuration on the Mac and left it unchecked.
Here is other information about how the system is set up.
Note: + means item is checked, - means item is unchecked
Apple Base Station V5.7
WAN Ethernet Port: Automatic (Default)
+Enable SNMP Access
+Enable Remote Configuration
-Enable Default Host at
+Enable Remote Printer Access
-Enable NAT Port Mapping Protocol
Internet:
Connect Using: PPP over Ethernet (PPPoE)
+always stay connected
Network:
+Distribute IP addresses
Airport client computers:
+Share a single IP address (using DHCP and NAT)
((Use 10.0.1.1 addressing))
Power Mac G5 Mac OS X (10.4.7)

Magic Packets with AirPort Extreme base station

Ok, so I would like to be able to wake my iMac with magic packets over the internet. It is connected to the internet via an AirPort Extreme base station, and I know that it won't work over wireless networks, but the iMac is connected and gets internet via ethernet from the AirPort. Is there any way I can set up port forwarding or something like that to wake my iMac remotely?

...should I have AirPort on my iMac turned off or on...
Since you are connected via Ethernet you would turn AirPort off.
Does the connection automatically default to Ethernet, even if AirPort is set "on," because presumably Ethernet is faster.
No. It gives priority based on how they are ordered in the list of network connections.

Configure protocol with airport extreme base station

Need powerbook g3 wireless internet compatible password. roamabout 802.11b cabletron card does not have wpa password option. There does not appear to be a compatible encryption type to use airport extreme base station with this card.

...should I have AirPort on my iMac turned off or on...
Since you are connected via Ethernet you would turn AirPort off.
Does the connection automatically default to Ethernet, even if AirPort is set "on," because presumably Ethernet is faster.
No. It gives priority based on how they are ordered in the list of network connections.

Several PC and Mac connectivity issues with Airport Extreme Base Station

Hello,
This is not all necessarily airport base station related, but there is some crossover, so I'm posting all of these issues...
Here is the laundry list of things that I can't make work in a home network that contains a PC w/ XP Home, MacBook 1.83 w/ 10.4.7, and Airport Extreme Base Station w/ Modem.
1. Can't see the PC from the Mac.
a. "Connect to server -> Browse" does not find the PC
b. "ipconfig" on PC provides valid looking IP address
c. ping from mac to PC IP address times out
d. Firewall on XP is disabled via control panel
b. Windows file and printer sharing is enabled
2. Can't see mac from PC
a. Windows file sharing enabled on mac
b. Firewall on mac disabled
c. I used \\MacIPAddr\shortusername
d. ping times out
3. Using dial-up to access internet, how do i tell airport to dial using PC?
a. this feature is working fine from mac
b. If already connected (via instruction from mac), can surf the internet fine from PC
c. Is this even possible from the PC?
4. Can't see printer connected to base station from PC
a. See it fine from mac
b. How do i "find" the printer on the PC?
c. Is Bonjour required for this? (I don't have it on the PC yet)
5. Can't see a "shared" printer on the PC from the mac
a. printer is connected directly to PC
b. Mac's add printer wizardry looks like it may "see" the printer, but then it asks for username and password for PC. This is XP home, with no usernames or passwords. Single user. Nothing seems to work in the credentials pop-up dialog.
Any suggestions on any of these issues is very welcome.
Thanks

Is the PC running any kind of internet security or firewall software?
1. Can't see the PC from the Mac.
2. Can't see mac from PC
Sharing files between an XP PC and a Mac running OS 10.4.x
http://www.ifelix.co.uk/tech/3020.html
3. Using dial-up to access internet, how do i tell
airport to dial using PC?
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com
4 . Can't see printer connected to base station from
PC
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://www.ifelix.co.uk/tech/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://www.ifelix.co.uk/tech/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://www.ifelix.co.uk/tech/1012.html
5. Can't see a "shared" printer on the PC from the
mac
Printing to a printer on a XP PC from a Mac running 10.4.x
http://www.ifelix.co.uk/tech/3015.html
Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows
http://www.ifelix.co.uk/tech/3014.html
iFelix

Using an External USB soundcard with Airport Extreme Base Station

Hello, I own a macbook, an airport extreme base station and a Native Instruments Audio Kontrol 1 USB 2.0 external sound card that works like a charm with my macbook. I have a printer and a hard drive connected to the USB from the Airport base station through a hub, and I was wondering if there is any way I could make my macbook recognize the external sound card when connected to the base station's USB port. I would like to be able to play music wirelessly through the base station but the application/driver from Native Instruments does not recognize the sound card plugged to the router.
Thank you

if there is any way I could make my macbook recognize the external sound card when connected to the base station's USB port
First welcome the the Apple Discussions Forum!
To your question - it's highly unlikely, sorry!

Printer that works with Airport Extreme Base Station

Hi. We are very new to Macs (2 weeks). Have a Mac Book and AEBS. Both work fine. Our HP printers, however, only work if connected directly to the Mac Book. I'm informed that we need to get a printer that works with the AEBS if we wish to have wireless printing. If anyone can recommend a printer that works with AEBS, we'd be grateful. Thanks.

Hello Jungle-cat. Welcome to the Apple Discussions!
Check out the following iFelix site to see which printers are known to work (not not) with the new 802.11n AirPort Extreme Base Station (AEBSn).

Airport Extreme Base Station and xBox wireless

We have 2 macs with Airport Extreme Base Station connecting to Cable modem for internet connection.
Recently bought an xBox with a USB wireless adaptor. When xBox is connected to the wireless network, internet connection of other computers dropped out and no longer can use internet until xBox is disconnected from the wireless network. It is the same problem even other computers are connected to Base Station with Ethernet cable.
Any settings in Airport Utility might fix this problem ?

We didn't have any problem before using the xBox wireless.
There are 2 Macs (iMac 20" & Macbook Pro 15") and they're connected to the Base Station via wireless.
The cable modem is Motorola Surfboard SB5100i and there is no login required from ISP for internet connection. Yes, the modem is connected to the WAN port of the Base Station.
With the Clients computer network settings, we are using DHCP. We have also tried with static IP and didn't make any differences.
I thought it could be the compatibility issue between the xBox wireless adaptor and the Base Station and on the other hand, the wireless protocols (802.11N/g/b) are industry standard and it doesn't matter who made them, they should work together.
The only idea that I have now is to try with other brand of wireless router and it might be a quick solution for this problem.
thanks,
David

Comcast HSI, AirPort Extreme Base Station issues

Recently, I've been having some connection issues with my Comcast High-Speed Internet and my AirPort Extreme Base Station. I'll be connected fine one minute, and the next my AirPort monitor drops to 2 bars of signal and nothing will connect. Resetting the base station and the modem works about 50% of the time, while just sitting here "dealing with it" works the other half of the time.
I rent my cable modem from Comcast, and I believe it is the Terayon TJ715. I went to the Apple Store San Francisco and had my base station replaced, thinking it was the culprit, but alas, the problem is continuing, only less frequently.
I've replaced all my ethernet cables, tried it with my AirPort Express (which works more often, yet has the same problem occasionally), yet my connection uptime and signal still drops to 2 bars and essentially disconnects.
Even stranger, the computer I have connected to the LAN port seems to work fine even when the computers connecting wirelessly are having issues.
I'm going down to a Comcast Support Center on Friday to (hopefully) replace my modem with a newer model (someone told me that older Comcast modems "kill" AirPort Base Stations), but other than that, any ideas? Anyone have this type of issue with Comcast in the past?
The 3 machines im running are:
Dual-Core 2.3Ghz Power Mac G5 via AirPort
867MHz PowerBook G4 (Titanium) via AirPort
800MHz iMac G4 (Flat-Panel) via Ethernet
Thanks,
Alexis
Dual-Core 2.3GHz Power Mac G5 Mac OS X (10.4.3)

Don,
Thank you for the link. However, it did not seem to solve my issue.
It's not that I haven't been able to connect to the internet at all using wireless. I will be connected fine (all 3 computers connecting to the internet simultaniously) when suddenly, any machine connected via AirPort (specifically my Dual-Core Power Mac G5) will receive two bars of signal and will no longer connect to the internet. The only remedy I've found is to reset both the cable modem and AirPort Extreme Base Station, and this only works about 50% of the time.
I am going to have Comcast replace the modem (and in the meantime, get new Ethernet cables) tomorrow, so hopefully I won't be having this issue anymore, but I'm more curious what may be causing the issue. Have you heard anything about older Comcast modems causing latency issues with AirPort Extreme Base Stations?
Thanks again,
Alexis

Airport Extreme Base station wireless setup problem with Zyxel 2602HW d1a

Hi!
Just bought a new Airport Extreme Base Station and it just doesn't work. Probably my fault, your help is very welcome!
My router Zyxel 2602HW D1A is the main router/modem. I can only connect to it wirelessly with my AEBS (so not via Ethernet/WAN). But, it doesn't seem to connect to this Zyxel in the wireless way. After I setup the AEBS to connect with this network I have to reset it to factory settings. Is it possible to connect only via wifi? Is it possible to this Zyxel? How can I setup the Zyxel to have everything ok to be ready for communication?
Firmware is up to date btw.
Thanks!
Bjorn

Hi Tesserax,
Thanks for replying. I would like to share USB attached printers and hard drives just with my 'own network' attached to the AEBSn. The other network I use just for the internet connection. Preferably the other network can't access my AEBSn network.
Am I clear? I am not sure
Message was edited by: BoMacBook

New Mac and Airport Extreme Base Station User - Setup question

Good Morning,
I just received my new MacBook Pro yesterday along with the Airport Extreme Base Station. I was tying to setup the airport extreme but have had no luck. I want to make sure I'm connecting things correctly - make sure I'm not doing something stupid.
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station. So I'll try that when I get home tonight. But I would appreciate any other suggestions - especially whether or not I've connected the airport extreme correctly to my cable modem.
Thanks, Susan
MacBook Pro Mac OS X (10.4)

I want to make sure I'm connecting things correctly
The network configuration should look something like the following:
Cable modem > (Ethernet cable) > [WAN port] AEBSn > (wireless) > MacBook Pro
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Since you changed your network configuration, you should perform a complete power recycle of your network components to allow enough time for them to "synchronize."
Modem/Router Power ReCycling
- Power-off the Cable modem, AirPort Extreme Base Station (AEBSn), & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBSn; Wait at least 5 minutes.
- Power-on the computer(s)
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station.
Yes, you will need this utility to perform the setup and follow-on administration of the AEBSn.

Netgear DG834G setup with Airport Extreme Base

Similar Messages

Maybe you are looking for