Netra 240 Key switch position chnage to UNKNOWN

I cannot boot up NETRA 240 , the key switch position is change to UNKNOWN even if the rotary switch is set up to NORMAL position!
I boot up the NETRA in using bootmode option skip_diag but after a while the system goes down and I cannot boot up after!
SEP 21 02:31:51 spatialnetra9: 00040076: "Keyswitch position has been changed to UNKNOWN."
SEP 21 02:50:33 spatialnetra9: 00060000: "SC Login: User admin Logged on."
SEP 21 04:02:30 spatialnetra9: 0004000a: "SC set bootmode to skip_diag, will expire THU SEP 21 04:12:30 UTC 2006."
SEP 21 04:02:42 spatialnetra9: 00040001: "SC Request to Power On Host."

Unfortunately, we do not use netmgt port (it is disconnected).
Even though, I can not use login and pass info in script (security reasons).

Similar Messages

Sun Netra 240 runs max level POST every power up

Hello, I have a Sun Netra 240 server box that on every power up runs the max level POST which takes a good 5 minutes to complete. I have the power key switch set to the normal position and not DIAG mode and I have the Diag-level set to "off" for the system configuration settings. Nothing gets reported as an error during the POST but it still continues to run full POST on every power cycle. Can anyone tell me what else to check or look at to make it stop? Thanks in advance.

I have no way to get a copy of this from the screen so I had to write it all down and hand jam it in. I only put my values, not the default values. These have not been changed though so I don't think it is any of these settings. Just for some background this server has been fine for the past year or so and then one day it just started doing this out of the blue.
test-args -
diag-passes 1
asr-policy normal
local-mac-address? true
fcode-debug false
silent-mode? false
scsi-initiator-id 7
oem-logo -
oem-logo? false
oem-banner -
oem-banner? false
ansi-terminal true
screen-#col 80
screen-#row 34
ttyb-rts-dtr-off false
ttyb-ignore-cd true
ttya-rts-dtr-off false
ttya-ignore-cd true
ttyb mode 9600,8,n,1,-
ttya mode 9600,8,n,1,-
output-device screen
input-device keyboard
auto-boot-on-error false
load base 16384
auto-boot? true
boot-command boot
diag-device disk
use-NVRAMRC true
security mode command
NVRAMRC devalias radbkup
security-#bad-logins 2
post-trigger power-on-reset
diag-script none
diag-level off
diag-switch false
obdiag-trigger power-on-reset
error-reset-recovery boot
Edited by: 941057 on Jun 15, 2012 2:38 PM

Two problems: hiding key-switch notes and messages to effect-plugins

Hello,
first please apologize my bad (school-) English, which I haven‘t much practiced sind I left school more than 30 yeras ago.
I have got two problems, and I should be grateful, if somebody could give me a hint.
1. I am using sample libraries, which I load in a sampler (Kontakt 2 of Native Instruments) in the instrument slot of Logic. These libraries work with key switches to choose between various articulations of an instrument. Unfortunately these key switching notes appear in the outprints (although the note, good so, does not sound – and isn‘t intended to sound).
Do you know a possibility to set a key switch and let the note hide in the outprint?
(I have also sent a fearture request to apple: creating an additional note line to an instrument, reserved for key switching commands.)
2. I am using Guitar Rig 2 as an effect-plugin in Logic. Guitar Rig is (regarding my puspose) organised in banks which contain various presets (settings of amplifiers, boxes, micros, effects and so on).
Is there in Logic a possibilities to send to effect-plugins commands which choose firstly a bank and secondly a preset in a bank of an effect-plugin in effect-slot?
Thank you for your answer in advance.
Yours sincerely Norbert
iMac Intel, 2GHz Mac OS X (10.4.8)

One method:
Let's say you have a flute sound from Kontakt 2...
1. Create a duplicate track for the Kontakt flute instrument in the Arrange window, just below the original track
2. Open your flute region in score or matrix, select the keyswitch notes and CUT them. Then exit the editor
3. Click on the duplicate track in the Arrange window and then use "paste at original position", (not regular CMD-V paste). Now your keyswitch notes are placed on the duplicate track in the exact location they were originally recorded at.
(Note: if this doesn't seem to paste anything (sometimes it happens), hit Undo. Then use the pencil tool to draw a blank region on your duplicate track. With that new region selected, use "paste at original position again" and it will work.)
4. With the new region selected, choose Options > Extended Parameters... a floating window will appear. Look for "Score:" at the bottom of the window. Click to the right of "Score:" so that it now says "Score: Off" for that region. This function works per region. Your keyswitches will still play but they won't be shown in the score. You can even hide this track if you want.
5. Repeat this process for all of your tracks with keyswitch notes in them.

Netra 240 - SSH not working

We are having a problem with a Sun Netra 240 � (Solaris 10) and are unable to SSH to the server. When entering the login and password � after about 15 seconds it closes out. We had NO trouble last week logging in using secure shell.
We can go to the console port with no problem.
Any ideas as to what might be the problem or fix?
Thanks,

You'll have to upgrade your IOS & license-
"ENTERPRISE PLUS IPSEC 3DES-Supports all the ENTERPRISE PLUS features, plus adds support for Triple Digital Encryption Standard (3DES) encryption to enable features that require this security, such as Secure Shell (SSH) Protocol and IP Security (IPSec) tunnels"
Hope it helps

Slow installation for Soaris 5.8 on Netra 240 using DVD

Hello,
I am installaing a Solaris 5.8 sparc OS on Netra 240 using a DVD-RAM.
The installation is very slow (more than 1.5 hours).
Is any configuration needed in the OBP ?
What is the required firmware version ?
Any other options ?
Thanks in advance,
Simcha Behar

Hello,
I am installaing a Solaris 5.8 sparc OS on Netra 240 using a DVD-RAM.
The installation is very slow (more than 1.5 hours).
Is any configuration needed in the OBP ?
What is the required firmware version ?
Any other options ?
Thanks in advance,
Simcha Behar

E4000 Key switch fan failure

I have an E4000 that listed several failures in prtdiag associated with a failed PPS. The PPS in question was not working at all and I have not replaced it. Prtdiag is still listing Key switch fan failure and prom detected failure.
Any suggestion on what might be the cause?
Thanks
NEW PRTDIAG:
System Configuration: Sun Microsystems sun4u 8-slot Sun Enterprise E4500/E5500
System clock frequency: 100 MHz
Memory size: 8192Mb
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 400 8.0 US-II 10.0
0 1 1 400 8.0 US-II 10.0
2 4 0 400 8.0 US-II 10.0
2 5 1 400 8.0 US-II 10.0
4 8 0 400 8.0 US-II 10.0
4 9 1 400 8.0 US-II 10.0
6 12 0 400 8.0 US-II 10.0
6 13 1 400 8.0 US-II 10.0
========================= Memory =========================
Intrlv. Intrlv.
Brd Bank MB Status Condition Speed Factor With
0 0 1024 Active OK 60ns 8-way A
0 1 1024 Active OK 60ns 8-way A
2 0 1024 Active OK 60ns 8-way A
2 1 1024 Active OK 60ns 8-way A
4 0 1024 Active OK 60ns 8-way A
4 1 1024 Active OK 60ns 8-way A
6 0 1024 Active OK 60ns 8-way A
6 1 1024 Active OK 60ns 8-way A
========================= IO Cards =========================
Bus Freq
Brd Type MHz Slot Name Model
1 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000
1 SBus 25 2 QLGC,isp/sd (block) QLGC,ISP1000U
1 SBus 25 3 SUNW,hme
1 SBus 25 3 SUNW,fas/sd (block)
1 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
3 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 2 QLGC,isp/sd (block) QLGC,ISP1000U
3 SBus 25 3 SUNW,hme
3 SBus 25 3 SUNW,fas/sd (block)
3 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
5 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000U
5 SBus 25 3 SUNW,hme
5 SBus 25 3 SUNW,fas/sd (block)
5 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
No failures found in System
===========================
Detected System Faults
======================
Key Switch Fan failure
Detected Wed Oct 12 16:25:13 2005
PROM detected failure
Detected Wed Oct 12 16:25:13 2005
This is the original prtdiag:
System Configuration: Sun Microsystems sun4u 8-slot Sun Enterprise E4500/E5500
System clock frequency: 100 MHz
Memory size: 8192Mb
========================= CPUs =========================
Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
0 0 0 400 8.0 US-II 10.0
0 1 1 400 8.0 US-II 10.0
2 4 0 400 8.0 US-II 10.0
2 5 1 400 8.0 US-II 10.0
4 8 0 400 8.0 US-II 10.0
4 9 1 400 8.0 US-II 10.0
6 12 0 400 8.0 US-II 10.0
6 13 1 400 8.0 US-II 10.0
========================= Memory =========================
Intrlv. Intrlv.
Brd Bank MB Status Condition Speed Factor With
0 0 1024 Active OK 60ns 8-way A
0 1 1024 Active OK 60ns 8-way A
2 0 1024 Active OK 60ns 8-way A
2 1 1024 Active OK 60ns 8-way A
4 0 1024 Active OK 60ns 8-way A
4 1 1024 Active OK 60ns 8-way A
6 0 1024 Active OK 60ns 8-way A
6 1 1024 Active OK 60ns 8-way A
========================= IO Cards =========================
Bus Freq
Brd Type MHz Slot Name Model
1 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000
1 SBus 25 2 QLGC,isp/sd (block) QLGC,ISP1000U
1 SBus 25 3 SUNW,hme
1 SBus 25 3 SUNW,fas/sd (block)
1 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
3 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 1 SUNW,qfe SUNW,sbus-qfe
3 SBus 25 2 QLGC,isp/sd (block) QLGC,ISP1000U
3 SBus 25 3 SUNW,hme
3 SBus 25 3 SUNW,fas/sd (block)
3 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
5 SBus 25 0 QLGC,isp/sd (block) QLGC,ISP1000U
5 SBus 25 3 SUNW,hme
5 SBus 25 3 SUNW,fas/sd (block)
5 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060
No failures found in System
===========================
Detected System Faults
======================
AC Box Fan failure
Detected Fri Sep 30 07:56:37 2005
System 5.0 Volt Precharge failure
Detected Sat Aug 27 23:10:31 2005
System 3.3 Volt Precharge failure
Detected Sat Aug 27 23:10:31 2005
Peripheral 12 Volt Precharge failure
Detected Sat Aug 27 23:10:31 2005
Peripheral 12 Volt Power failure
Detected Sat Aug 27 23:10:30 2005
Auxiliary 5.0 Volt Power failure
Detected Sat Aug 27 23:10:30 2005
AC Power failure
Detected Sat Aug 27 23:10:29 2005
Key Switch Fan failure
Detected Thu Aug 25 18:47:11 2005
PROM detected failure
Detected Thu Aug 25 18:47:11 2005

I don't know which fan I need replace and which fan is the FAN two, who can help me?
2970 fans are NOISY. So power it up and look for the one that's not spinning or is the most quiet one.

Re-mapping key switches in Kontakt 3

Hi
does anyone know how to change where the keys switches are mapped to??
as an example, i have a violin with key-switches loaded. in the mapping area i can move all the groups to meet the key-switches down in the C0 range but i want to re- assign the key switches up to meet the range of the violin.
if i move the violin out of range it does my head in when i look at it in the score editor for editing.... violin in bass clef!!
thanks

Have a look at the pic below, hope it will solve your problem.
!http://img264.imageshack.us/img264/2057/keyswkontakt.gif!
!http://img59.imageshack.us/img59/4967/aglogo45.gif! [www.audiogrocery.com|http://www.audiogrocery.com]

SCSI warnings - Solaris 10 Install - Netra 240

Hi Friends,
Im doing some installation using Netra 240 & I've external storage (Via Store Edge S1) - However after i finished the installation I keep getting this messages on the console.
Im not sure what these messages are. If anyone can throw some lo
i keep getting these messages,
ct 13 08:01:15 C69N2 got SCSI bus reset
Oct 13 08:01:15 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:15 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:21 C69N2 Resetting scsi bus, got incorrect phase from (0,0)
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:21 C69N2 got SCSI bus reset
Oct 13 08:01:21 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:21 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:24 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:24 C69N2 drive offline
Oct 13 08:01:24 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:24 C69N2 i/o to invalid geometry
Oct 13 08:01:24 C69N2 md_stripe: WARNING: md: d17: write error on /dev/dsk/c1t0d0s7
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:27 C69N2 Resetting scsi bus, got incorrect phase from (0,0)
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:27 C69N2 got SCSI bus reset
Oct 13 08:01:27 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd5):
Oct 13 08:01:27 C69N2 auto request sense failed (reason=reset)
Oct 13 08:01:33 C69N2 scsi: WARNING: /pci@1c,600000/scsi@2 (glm0):
Oct 13 08:01:33 C69N2 Resetting scsi bus, got incorrect phase from (0,0

bash-3.00#
bash-3.00# iostat -En
c1t1d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: SEAGATE Product: ST373453LSUN72G Revision: 0449 Serial No: 0444J28H3B
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c0t0d0 Soft Errors: 2 Hard Errors: 0 Transport Errors: 1
Vendor: TEAC Product: DV-28E-C Revision: 1.4B Serial No:
Size: 0.00GB <0 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 2 Predictive Failure Analysis: 0
c1t0d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: SEAGATE Product: ST373453LSUN72G Revision: 0449 Serial No: 0448J2F3JK
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t12d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3147N SUN146G Revision: 0602 Serial No: 0513C0144Y
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t13d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3147N SUN146G Revision: 0602 Serial No: 0513C0143U
Size: 146.80GB <146800115712 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c2t14d0 Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU Product: MAT3073N SUN72G Revision: 0602 Serial No: 0512B02E3N
Size: 73.40GB <73400057856 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
bash-3.00#
bash-3.00#

FN-CTRL Key Switch MS-1733

Hi is there any possibility to switch the fn and the ctrl key on my ms-1733. I think the position isn't good like it is. thank you for your help

Quote from: viper2035 on 13-November-10, 23:17:51
i don't know if it is important but i have a german keyboard layout.
nope, i need the info above[in prevision reply]

Dynamic switch positions of two VBox inside a HBox

I have a design issure, which is something like:
<mx:HBox>
      <mx:VBox id="vb1">
         //contains Image and Text
      </mx:VBox>
      <mx:VBox id="vb2">
         //contains Text
      </mx:VBox>
</mx:HBox>
I like to switch the positions of the two VBox with just one click on a button. I think it can also be done by swarping the
contents of the two VBox so it looks switch of the two VBox. Maybe drag and Drop on the VBoxes? Any suggestions? Thx.

Use swapChildren and swapChildrenAt functions.
like
hbox1.swapChildren(child1,child2)
hbox1.swapChildrenAt(index1,index2)
Tanu

Alt key switching documents instead of Creating Clipping Mask - New Mac Pro 2014 - Please help

I just got a new Mac Pro, and when I use the alt/option key as a shortcut in the layers palette (to create clipping masks and duplicate layers) instead it switches to other documents that I have open. It's only after this happened that I realized how often I use the option key in my work flow and it's frustrating.
Please help,
Thanks,
Lonno

Just solved it. It had to do with my secondary monitor, which is where my layers palette was. I used this link:
https://discussions.apple.com/thread/5476222?tstart=0
and turned off all the mission control settings I don't use. Apparently it was switching monitors whenever I used the alt key.
-Lonno

E450 won't boot with key switch, does with keyboard

Evening chaps.
As the subject suggests, this is actually a follow up question to a previous thread by the same name.
I have a E450 here which until about 4 hours ago was running just fine using a serial console.
Up till then it has had no issues, problems, etc and has run absolutely flawlessly.
I did a nice graceful shutdown (Solaris 9), and then used the power-off from the obp.
I turned the key off, powered the machine off, switched some disks around and when it came to powering the unit back on ... it wouldn't!
No matter what I did, I could not bring it back to life.
The 'solution' was to plug a keyboard in and use the power key on that.
Now my question ... does anyone have any idea as to what causes this and how do I go about fixing it???
Having to have a keyboard attached to the machine to turn it on has knobs on it!
Any suggestions here would be greatly appreciated as this is a 'new' behaviour for this machine.
/BGM

Me too! Did you ever sort this out?
FWIW, here are the eeprom settings:bash-2.03$ eeprom
tpe-link-test?=true
scsi-initiator-id=7
keyboard-click?=false
keymap: data not available.
.reboot-flag=false
.reboot-posc=0
.reboot-posl=0
.reboot-cmd: data not available.
ttyb-rts-dtr-off=false
ttyb-ignore-cd=true
ttya-rts-dtr-off=false
ttya-ignore-cd=true
ttyb-mode=9600,8,n,1,-
ttya-mode=9600,8,n,1,-
pci-slot-skip-list=none
pci0-probe-list=1,3,2,4
upa-port-skip-list=none
memory-interleave=auto
disk-led-assoc=0
diag-level=min
diag-script=normal
diag-targets=none
diag-trigger=power-reset
diag-continue?=false
diag-passes=1
diag-verbosity=tests
env-monitor=enabled
.asr-disable-list: data not available.
.asr-status=18437736870358094097
.post-status=18437736870358094097
.post-address=18446744073441856352
.post-flag=0
.rsc-status=85
.obp-flags=0
.obp-state=6
.obp-status=0
mfg-options=server-class
#power-cycles=87
system-board-serial#=852M22B2
system-board-date=36802ca6
fcode-debug?=false
output-device=screen
input-device=keyboard
load-base=16384
boot-command=boot
auto-boot?=true
auto-boot-on-error?=false
watchdog-reboot?=false
diag-file: data not available.
diag-device=net
boot-file: data not available.
boot-device=disk net
local-mac-address?=false
ansi-terminal?=true
screen-#columns=80
screen-#rows=34
silent-mode?=false
use-nvramrc?=false
nvramrc: data not available.
security-mode=none
security-password: data not available.
security-#badlogins=0
oem-logo: data not available.
oem-logo?=false
oem-banner: data not available.
oem-banner?=false
hardware-revision=UUUUUUUUUUUUUUU
last-hardware-update=UUUUUUUUUUUUUUUUUUUUUUU
.upa-noprobe-mask=0
diag-switch?=false

EP6: Switch positions of Detailed Nav and Dynamic Nav iviews?

By default, the Detailed Navigation iview is, from the top of the screen, first, then the Dynamic Navigation iview.
Is there any way to switch this?
I tried changing the layout of the Desktop Innerpage (from the content list of the Default Framework Page), but these two iviews aren't even visible in the Edit Layout Screen.

Hi Eric,
you should be able to see these iViews there. Just continue clicking on Edit (select Desktop Innerpage first and then click on edit). In the next screen you should see several iViews (among them Detailed Navigation and Dynamic Navigation) now click on Layout and you should be able to change the position of these two iViews.
Hope this helps,
Holger.

Default switch positions

I have a VI which is controlling a number of solenoid drives via software enabled switches. Is it possible to set the default position of these switches. For example everytime I turn the model on I would like the heater gun switch to be on (in the UP position) with the hydraulic supply off (in the DOWN position). I have tried setting the required default positions and saving the VI but they always default to the same position.
Thanks.
Richard
Solved!
Go to Solution.

It is often better to select the desired controls first so only those get specific default values. For example if you also have a large graph with megabytes of data, setting it to default would greatly increase the size of the VI file.
LabVIEW Champion . Do more with less code and in less time .

Keyboard problem - alt & shift key switch

Suddenly the alt & shift keys have switched functions but only for the "3" key along the top of the keyboard. Previously shift + 3 gave the pound sterling sign, but this is now alt + 3, which took some finding, shift + 3 is this sign #. I would like the pound sign back at shift + 3 where it's shown. I can't find anything to show how to do this, or why it changed in the first place. Please help.
Thank you.
Janet.

Perhaps the System Preferences have been changed from a British keyboard to a US keyboard. Go to Sys Prefs/Lang & Text/Input Sources to check what is selected.
Dah•veed

Netra 240 Key switch position chnage to UNKNOWN

Similar Messages

Maybe you are looking for