Netra T1 (200) and Sun Storedge D1000

Following scenario:
I want to set up an Sun Cluster 3 enviroment. For that I have two Netra T1 (200) and two D1000.
The Netra T1 has only one SCSI interface on borad, so I added an PCI SCSI/Ethernet combocard in both server. Now I am able to write data from each server to each disk array.
But the following error occur:
After all parts were connected, I execute an "probe-scsi-all" on one server to see the disks in the D1000, but I cannot see any disks of the D1000.
On the second server I got the error message:
Nov 5 10:58:13 wapgw2 scsi: WARNING: /pci@1f,0/pci@1/pci@5/SUNW,isptwo@4 (isp0):
Nov 5 10:58:13 wapgw2 SCSI Cable/Connection problem.
Nov 5 10:58:13 wapgw2 scsi: Hardware/Firmware error.
Nov 5 10:58:13 wapgw2 scsi: WARNING: /pci@1f,0/pci@1/pci@5/SUNW,isptwo@4 (isp0):
Nov 5 10:58:13 wapgw2 Fatal error, resetting interface
I work with Solaris 8, patchlevel 24. The Prom was already updated (111991-06).
Can somebody help me?

Hello,
thanks for help.
In order to change the scsi initiator on one of the two machines, I need the path of both interfaces.
Since now I changed it not.
As I know you do the following:
- switch off one server
- set auto-boot? to false
- reset-all
- probe-scsi-all
after that you have the path of both scsi interfaces. With that info you perform a nvedit and set the id of one machine for example to 6.
But I thought that regardless of the scsi id, I should be able to do a probe-scsi-all.
Was this a mistake from me?

Similar Messages

Installation failed when using Jumpstart Server to install SUN Netra T1 200

I have a problem to install a couple of Sun Netra T1 200 Servers with a Jumpstart Server. The Jumpstart Server is set up and I have executed the add_install_client Script. If I boot the Server which should to be installed the server crashes after getting the assigned IP-Address with a software fault.
Attached i will sent the Jumpstart-Client-Output and the config Files of the Jumpstart-Server.
****Netra T1 Server Output, while configured as an Jumpstart client:****
ok boot net -install
Resetti
LOM event: +2h28m47s host reset
ng ...
`
Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1024 MB memory installed, Serial #16692502.
Ethernet address 8:0:20:fe:b5:16, Host ID: 80feb516.
Executing last command: boot net -install
Boot device: /pci@1f,0/pci@1,1/network@c,1 File and args: -install
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
2ae00 Warning: boot will not enable cache
Requesting Internet address for 8:0:20:fe:b5:16
Enter filename [kernel/sparcv9/unix]:
Enter default directory for modules [platform/SUNW,UltraAX-i2/kernel /platform/sun4u/kernel /kernel /usr/kernel]:
SunOS Release 5.8 Version Generic_108528-13 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
whoami: no domain name
panic[cpu0]/thread=300010a9ba0: Can't invoke , error 2
000002a1000f7a40 genunix:icode+274 (ffbefff0, 0, 300010a7b88, 0, ffbefffc, ffffffffffffffff)
%l0-3: 00000000ffbefffc 0000000000000000 0000000000002000 000002a10000fd20
%l4-7: 0000000000000bb8 0000000010423a00 000000001041b2f8 00000000000007a9
syncing file systems... done
skipping system dump - no dump device configured
rebooting...
Resetti
LOM event: +2h36m51s host reset
ng ...
p
Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1024 MB memory installed, Serial #16692502.
Ethernet address 8:0:20:fe:b5:16, Host ID: 80feb516.
Executing last command: boot
Boot device: disk File and args:
SunOS Release 5.8 Version Generic_108528-13 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
configuring IPv4 interfaces: eri0.
Hostname: infrasrv
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c1t0d0s4: is stable.
/dev/rdsk/c1t0d0s6: is stable.
Starting IPv4 routing daemon.
starting rpc services: rpcbind done.
Setting netmask of eri0 to 255.255.255.0
Setting default IPv4 interface for multicast: add net 224.0/4: gateway infrasrv
syslog service starting.
Print services started.
Jun 26 04:48:14 infrasrv sendmail[220]: My unqualified host name (infrasrv) unknown; sleeping for retry
volume management starting.
The system is ready.
infrasrv console login: root
Password:
Last login: Thu Jun 26 02:13:59 on console
Jun 26 04:48:24 infrasrv login: ROOT LOGIN /dev/console
Sun Microsystems Inc. SunOS 5.8 Generic Patch October 2001
Sun Microsystems Inc. SunOS 5.8 Generic Patch October 2001
# uname -i
SUNW,UltraAX-i2
# ^[[A
^[[A: not found
# uname -m
sun4u
*****Config Files of the Jumpstart-Server******************
Sysidcfg
bootparams
bash-2.03# more bootparams
infrasrv root=adminws:/cdrom/sol_8_202_sparc/s0/Solaris_8/Tools/Boot install=ad
minws:/export/install boottype=:in sysid_config=adminws:/export/sysidcfg install
_config=adminws:/export/config rootopts=:rsize=32768
bash-2.03#
rules
bash-2.03# more rules
#       @(#)rules 1.12 94/07/27 SMI
# The rules file is a text file used to create the rules.ok file for
# a custom JumpStart installation. The rules file is a lookup table
# consisting of one or more rules that define matches between system
# attributes and profiles.
# This example rules file contains:
#   o syntax of a rule used in the rules file
#   o rule_keyword and rule_value descriptions
#   o rule examples
# See the installation manual for a complete description of the rules file.
# RULE SYNTAX:
# [!]rule_keyword rule_value [&& [!]rule_keyword rule_value]... begin profile fi
# nish
# "[ ]" indicates an optional expression or field
# "..." indicates the preceding expression may be repeated
# "&&" used to "logically AND" rule_keyword and rule_value pairs together
# "!" indicates negation of the following rule_keyword
# rule_keyword a predefined keyword that describes a general system
# attribute. It is used with the rule_value to match a
# system with the same attribute to a profile.
# rule_value a value that provides the specific system attribute
# for the corresponding rule_keyword. A rule_value can
# be text or a range of values (NN-MM).
# To match a range of values, a system's value must be
# greater than or equal to NN and less than or equal to MM.
# begin a file name of an optional Bourne shell script
# that will be executed before the installation begins.
# If no begin script exists, you must enter a minus sign (-)
# in this field.
# profile a file name of a text file used as a template by the
# custom JumpStart installation software that defines how
# to install Solaris on a system.
# finish a file name of an optional Bourne shell script
# that will be executed after the installation completes.
# If no finish script exists, you must enter a minus sign (-)
# in this field.
# Notes:
# 1. You can add comments after the pound sign (#) anywhere on a line.
# 2. Rules are matched in descending order: first rule through the last rule.
# 3. Rules can be continued to a new line by using the backslash (\) before
# the carriage return.
# 4. Don't use the "*" character or other shell wildcards, because the rules
# file is interpreted by a Bourne shell script.
# RULE_KEYWORD AND RULE_VALUE DESCRIPTIONS
# rule_keyword rule_value Type rule_value Description
# any minus sign (-) always matches
# arch text system's architecture type
# domainname text system's domain name
# disksize text range system's disk size
# disk device name (text)
# disk size (MBytes range)
# hostname text system's host name
# installed text text system's installed version of Solaris
# disk device name (text)
# OS release (text)
# karch text system's kernel architecture
# memsize range system's memory size (MBytes range)
# model 'text' system's model number
# network text system's IP address
# totaldisk range system's total disk size (MBytes range)
# RULE EXAMPLES
# The following rule matches only one system:
# hostname sample_host - host_class set_root_pw
# The following rule matches any system that is on the 924.222.43.0 network
# and has the sun4c kernel architecture:
# Note: The backslash (\) is used to continue the rule to a new line.
#network 924.222.43.0 && \
# karch sun4c - net924_sun4c -
# The following rule matches any sparc system with a c0t3d0 disk that is
# between 400 to 600 MBytes and has Solaris 2.1 installed on it:
#arch sparc && \
# disksize c0t3d0 400-600 && \
# installed c0t3d0s0 solaris_2.1 - upgrade -
# The following rule matches all x86 systems:
#arch i386 x86-begin x86-class -
# The following rule matches any system:
#any - - any_machine -
hostname infrasrv - infrasrv_class -
hostname msm_srv1 - msm_srv_class -
hostname msm_srv2 - msm_srv_class -
bash-2.03#
class
bash-2.03# more infrasrv_class
install_type initial_install
system_type standalone
partitioning explicit
filesys c0t0d0s0 2048 /
filesys c0t0d0s1 10
filesys c0t0d0s3 1024 swap
filesys c0t0d0s4 2048 /var
filesys c0t0d0s5 2048 /opt
filesys c0t0d0s6 free /export
cluster SUNWCXall
bash-2.03# more msm_srv_class
install_type initial_install
system_type standalone
partitioning explicit
filesys c0t0d0s0 2048 /
filesys c0t0d0s1 10
filesys c0t0d0s3 1024 swap
filesys c0t0d0s4 2048 /var
filesys c0t0d0s5 free /opt
cluster SUNWCXall
bash-2.03#
ethers
bash-2.03# more ethers
8:00:20:fe:b5:16 infrasrv
bash-2.03#
hosts
bash-2.03# more hosts
# Internet host table
127.0.0.1 localhost
192.168.0.220 adminws loghost
192.168.0.210 infrasrv
192.168.0.200 tc
bash-2.03#
dfstab
bash-2.03# more dfstab
# Place share(1M) commands here for automatic execution
# on entering init state 3.
# Issue the command '/etc/init.d/nfs.server start' to run the NFS
# daemon processes and the share commands, after adding the very
# first entry to this file.
# share [-F fstype] [ -o options] [-d "<text>"] <pathname> [resource]
# .e.g,
# share -F nfs -o rw=engineering -d "home dirs" /export/home2
share -d "jumpstart conf dir" /export/config
share -F nfs -o ro,anon=0 /export/install
share -F nfs -o ro,anon=0 /cdrom/sol_8_202_sparc/s0/Solaris_8/Tools/Boot
bash-2.03#
tftpboot
bash-2.03# pwd
/tftpboot
bash-2.03# ls -al
total 348
drwxrwxr-x 2 root other 512 Jun 26 11:45 .
drwxr-xr-x 24 root root 512 Jun 26 11:45 ..
lrwxrwxrwx 1 root other 26 Jun 26 11:45 C0A800D2 -> inetboot.SUN4U.Solaris_8-1
lrwxrwxrwx 1 root other 26 Jun 26 11:45 C0A800D2.SUN4U -> inetboot.SUN4U.Solaris_8-1
-rwxr-xr-x 1 root other 159416 Jun 26 11:45 inetboot.SUN4U.Solaris_8-1
-rw-r--r-- 1 root other 318 Jun 26 11:45 rm.192.168.0.210
lrwxrwxrwx 1 root other 1 Jun 26 11:45 tftpboot -> .
bash-2.03#

Hi,
It seems to me that you have not created a proper sysidcfg file. From your post, it looks to me like your sysidcfg contains no entries. This is why it prompts you to enter the kernel path. Look on docs.sun.com for a guide to creating the sysidcfg file .

Sun netra t 200 please help

Hello and Hi to all members,
I am trying to install solaris 9 OS to my sun netra t 200, but the problem is i dont have any sun keyboard. I am currently using serial connection installing the OS. I have problem finding the command especially F2_standard.
please help me regarding the problem??I tried to search from the net but i still can find it?? please help me??
thanks
syafiq

During a serial installation, it asked for your terminal type. How did you respond?
During the serial installation it displays a message that function keys like [F2] can be replaced with the key sequence <ESC>-<2>. That should work fine with a 'vt100' connection.
Darren

Sun Storedge L9 command utility, need to load and unload tapes.

I am looking for a utility that will unload, and reload an L9 Sun storedge.
I found:
http://www.sun.com/bigadmin/jsp/descFile.jsp?url=descAll/l9ctl
This utility has some calls that either we don't have, or I can't find:
loadmedia.cgi
inloadmedia.cgi
Am I setting this up incorrectly?
Where is this stuff supposed to be?
I am running on a sun ulta-5, Solaris 8.

Hello!
Before use, You should small customize script:
1) Change
$LibraryHostName="http://l9"; - It's library hostname.
Or set this name in /etc/hosts
$AdminPwd="12341234"; - password to Library
And, of course, before use this script - you should setup netwotk connection of L9.
Another way - use project MTX.
http://freshmeat.net/projects/mtx/releases
This program use SCSI commands for control library.
Regards.

Are SUN StorEdge c2 and Sun Storagetek C2 the same ?

Hello All,
Are SUN StorEdge c2 and Sun Storagetek C2 the same ? or are they 2 different products.
Thanks
Venkat Jupalli

mmmmn, not sure about this one, but I would assume that moving from StorEdge to Storagetek is brand name related and came about from Sun Microsystems' acquisition of StorageTek late '05. Call marketing for more information.

Netra t1 200 diag light

I have a older netra t1 with the diag lights on amber in the front.
i did a prtdiag and it does not show any faults..
<div class="pre"><pre>System Configuration: Sun Microsystems sun4u Netra T1 200 (UltraSPARC-IIe 500MHz)System clock frequency: 100 MHzMemory size: 2048 Megabytes========================= CPUs ========================= Run Ecache CPU CPUBrd CPU Module MHz MB Impl. Mask--- --- ------- ----- ------ ------ ---- 0 0 0 500 0.2 13 1.4========================= IO Cards ========================= Bus# FreqBrd Type MHz Slot Name Model--- ---- ---- ---- -------------------------------- ---------------------- 0 PCI-1 33 12 ebus 0 PCI-1 33 3 pmu-pci10b9,7101 0 PCI-1 33 3 lomp 0 PCI-1 33 7 isa 0 PCI-1 33 12 network-pci108e,1101 SUNW,pci-eri 0 PCI-1 33 12 usb-pci108e,1103.1 0 PCI-1 33 13 ide-pci10b9,5229 0 PCI-1 33 5 network-pci108e,1101 SUNW,pci-eri 0 PCI-1 33 5 usb-pci108e,1103.1 0 PCI-2 33 8 scsi-glm Symbios,53C896 0 PCI-2 33 8 scsi-glm Symbios,53C896 No failures found in System===========================</pre></div>
is there any way to reset the diag lights ? or any other ways of finding a problem other than prtdiag ?
Thanks

Have you used lom?
#. should get you to lom> prompt
lom> environment
or
lom> check
Once you see what is faulty or repair it then you can
lom> faultoff
lom> console
will get you back to Solaris.
Chapter 8 in the Netra T1 AC200 and DC200 Server User's Guide has great info on LOM - Lights Out Management Looks like manual is only available to contract sunsolve users:
http://sunsolve.sun.com/handbook_private/Systems/Netra_T1_AC 200_shared/docs.html
This assumes you have SUNWlomr, SUNWlomu & SUNWlomm packages loaded & patched.

Solstice backup 6.1 hang when invoking the autochanger "SUN Storedge L8 "

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

My company have a SUN Storedge L8 attached to a SUN Solaris 9 (SPARC) while I can only do a tar to the /dev/rmt/0, whenever I tried to interact with the jukebox with the solstice backup, the program hang definitely.
grep '/usr/kernel/drv/lus' /var/sadm/install/contents
/usr/kernel/drv/lus f none 0555 root bin 34624 12073 993189557 SUNWsbus2
/usr/kernel/drv/lus.conf f none 0444 root bin 3754 45438 993190441 SUNWsbus2
/usr/kernel/drv/lus32 f none 0555 root bin 33444 4422 993213667 SUNWsbus2
pkginfo -l SUNWsbus2
PKGINST: SUNWsbus2
NAME: Solstice Backup (Backup/Recover) Device Drivers
CATEGORY: system
ARCH: sparc
VERSION: 6.1,REV=Build.186
BASEDIR: /
VENDOR: Sun Microsystems, Inc.
PSTAMP: gelato010622054128
INSTDATE: Apr 08 2003 13:25
STATUS: completely installed
FILES: 48 installed pathnames
44 executables
37896 blocks used (approx)
this machine has installed the solstice backup manager
pkginfo | grep -i Solstice
system SUNWmibii Solstice Enterprise Agents 1.0.3 SNMP daemon
system SUNWsacom Solstice Enterprise Agents 1.0.3 files for root file system
system SUNWsadmi Solstice Enterprise Agents 1.0.3 Desktop Management Interface
system SUNWsadml Solstice Launcher.
system SUNWsadmx Solstice Enterprise Agents 1.0.3 Desktop Management Interface Libraries (64-bit)
system SUNWsasnm Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol
system SUNWsasnx Solstice Enterprise Agents 1.0.3 Simple Network Management Protocol Libraries (64-bit)
application SUNWsbuc Solstice Backup (Backup/Recover) Client
application SUNWsbum Solstice Backup (Backup/Recover) Man
application SUNWsbun Solstice Backup (Backup/Recover) Storage Node
application SUNWsbus1 Solstice Backup (Backup/Recover) Server
system SUNWsbus2 Solstice Backup (Backup/Recover) Device Drivers
under the server->registration, I found that the registration contains :-
Autochanger Module, 9 slots/9
ClientPaks for Windows/1
Networker for UNIX, Workgroup edition (8 clients per server)1 server
Networker Module for Oracl/1
BTW, inquire shows:-
/etc/LGTOuscsi/inquire
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
where cfgadm -alv shows:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
nsrjb shows
Jukebox L8:
slot volume pool volume id recyclable
1: dwbak.inc.day0.wk0.001* 2481680129
2: dwbak.inc.day0.wk0.002 DW Incremental 2481704705 no
3: dwbak.inc.day0.wk0.003 DW Incremental 2481729793 no
4: -* -
5: dwbak.inc.day0.wk0.005 DW Incremental 2481779201 no
6: dwbak.inc.day0.wk0.006 DW Incremental 2481804289 no
7: dwbak.inc.day0.wk0.007 DW Incremental 2481829889 no
8: dwbak.inc.day0.wk0.008 DW Incremental 2481854209 no
*not registered in the NetWorker media data base
drive 1 (/dev/rmt/0cbn) slot 5: dwbak.inc.day0.wk0.005
nsrjb -HE hang indefinitly, so does nsrjb -HHE. devfsadm -c tape also hang while simply devfsadm can run without problem and cfgadm -alv c3 provide the following:-
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
nsjrb result should be past history, coz I am doing tar and manually changing the slot for quite some time already. Now I unconnect the cable and run devfsadm and then cfgadm -alv shows
cfgadm -alv
Ap_Id Receptacle Occupant Condition Information
When Type Busy Phys_Id
c0 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6:scsi
c0::/dev/lus connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM n /devices/pci@8,700000/scsi@6:scsi::/dev/lus
c0::dsk/c0t6d0 connected configured unknown TOSHIBA DVD-ROM SD-M1401
unavailable CD-ROM y /devices/pci@8,700000/scsi@6:scsi::dsk/c0t6d0
c1 connected configured unknown
unavailable fc-private n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc
c1::21000004cfe34092 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34092
c1::21000004cfe34350 connected configured unknown SEAGATE ST373307FSUN72G
unavailable disk n /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:fc::21000004cfe34350
c2 connected configured unknown
unavailable scsi-bus n /devices/pci@8,700000/scsi@6,1:scsi
c2::lus1 connected configured unknown
unavailable unknown n /devices/pci@8,700000/scsi@6,1:scsi::lus1
c3 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@4:scsi
c3::lus2 connected configured unknown HP Ultrium 1-SCSI
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@4:scsi::lus2
c3::rmt/0 connected configured unknown HP Ultrium 1-SCSI
unavailable tape n /devices/pci@8,600000/pci@1/scsi@4:scsi::rmt/0
c4 connected configured unknown
unavailable scsi-bus n /devices/pci@8,600000/pci@1/scsi@5:scsi
c4::lus3 connected configured unknown
unavailable unknown n /devices/pci@8,600000/pci@1/scsi@5:scsi::lus3
usb0/1 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-kbd n /devices/pci@8,700000/usb@5,3:1
usb0/2 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:2
usb0/3 connected configured ok Mfg: <undef> Product: <undef> NConfigs: 1 Config: 0 <no cfg str descr>
unavailable usb-mouse n /devices/pci@8,700000/usb@5,3:3
usb0/4 empty unconfigured ok
unavailable unknown n /devices/pci@8,700000/usb@5,3:4
and inquire still shows
[email protected]:TOSHIBA DVD-ROM SD-M14011009|CD-ROM
[email protected]:ADIC FastStor 2 A12r|Autochanger (Jukebox)
[email protected]:HP Ultrium 1-SCSI E3 |Tape
[email protected]:HP Ultrium 1-SCSI E3 |Tape
and then I reconnect the cable I saw a lot of error message in dmesg:-
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:47:37 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:47:37 server Received unexpected SCSI Reset
Jun 19 13:51:30 server scsi: [ID 107833 kern.notice] /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:30 server Failed to Get Features
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server ISP: Firmware cmd timeout
Jun 19 13:51:50 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@4 (qus0):
Jun 19 13:51:50 server Fatal error, resetting interface, flg 1
and devfsadm hang. So I double check the past demsg and found a lot of similar SCSI error message as below:-
Jun 19 13:43:12 server probe request for LUN 0 denied: max LUN -1
Jun 19 13:43:12 server scsi: [ID 107833 kern.warning] WARNING: /pci@8,600000/pci@1/scsi@5 (qus1):
Is that represent a hardware failure either on the jukebox or the SCSI controller? Or it is indeed a software corruption that can only be solved by reinstallation? But unfortunately I don't have the media on hand.
PS.a more details can be found under expert exchange thru the links below:-
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23413012.html#a21749881
http://www.experts-exchange.com/OS/Unix/Solaris/Q_23478147.html

Sun StorEdge 3510

Dears,
Good day,
I need your support to guide me to configure Sun StorEdge 3510. I have 24 Disks and single controller. I is connected to one host. I want to configure it with the most biggest storage. I want to implement RAID 5 on 11 disks on the first enclosure and the same to the second enclosure with two disks spare each one in the same enclosure.
Can you guide me throw this?
Thanks a lot.

Wow, it took me about 5 hours to set mine up from scratch and I'm a pretty strong storage guy. Here's an overview of what I did. Most of the info is in the 3510 documentation.
Step 1 is connectivity. Get your host to see the 3510 (FC).
Step 2 - use the cli utilities to setup the IP address on the controller (in-band).
Step 3 - ssh in, setup the RAID and presentation of the luns
Step 4 - rescan on the hosts to see the new luns

Install SUN StorEdge L280 to Solaris 10 x86

Hi, i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks

i need help with install & configure SUN StorEdge L280. I have SOLARIS 10 x86 platform on HP DL 380 g3. I need help with this. I dont understend what with this, what drivers is need... On sparc is all ok with veritas netbackup, but on x86...any help?thanks
The L280 (or HP SureStore Autoloader 718) contains a DLT7000 drive. There is no reason why the generic SCSI tape driver doesn't support these drives.
If you're asking for software to control the autoloader, a similar software like Veritas NetBackup is required. Veritas supplies a replacement driver.
Now I see why your L280 doesn't work with your HP server. The L280 requires a HVD (High Voltage Differential) SCSI controller. The standard SCSI interface is SE (Single Ended) or LVD (Low Voltage Differential). Neither SE nor LVD are compatible with HVD. You won't see the device and can even damage the device and/or the controller.
Get a HVD SCSI controller (Symbios SYM22802, Part-No 375-0006) or Adaptec AHA-2944UW (not AHA-2940UW which is SE!!).
The Sun labeled HP Autoloaders (StorEdge L9, L280) use HVD SCSI while the original ones (SureStore 1/9, 718) use LVD or SE SCSI.
Michael
Robert,
any update ?
Message was edited by:
MAALATFT

Veritas Volume manager 4.0 with Sun StorEdge 3310 D

I am running into a problem. The vxconfigd deamon always dump core when rebooting.
Our environment is listed below.
OS environemt.
     SunOS server1 5.8 Generic_117350-43 sun4u sparc SUNW,Sun-Fire-V240
Software installed.
     Sun Cluster 3.0
     Veritas Volume Manager 4.0 MP2.
Disk Array associated.
     Sun StorEdge 3310 D.
I looked up veritas.com and find Array Support Library (ASL) for Sun StorEdge 3xxx Series is recommended. But I didn't find this library is running on this server.
Please refer to this following link
http://support.veritas.com/docs/277923
As our system is one of critical systems and I'd like to confirm that I can follow up this procedure without doing harm things to our system.
Jeff

No problem Jeff :)
I took a look at the Veritas doc and you're right it does seem to cover everthing.
Has the vxconfigd core dumped since the start? ie from the moment it was installed?
I have installed VXVM 4.0 with Solaris 8 but without the ASL and this worked ok, I know that's not much help to you but I am not sure the ASL will help. Mind you I have not installed it with Sun Cluster 3.0.

Sun StorEdge L8 Tape Library (UREGENT!!)

hi all
help needed.. i am new in this.. i ahve to do backup in the Sun StorEdge L8 every weekend.. as usual i will unload the Tape 1 and load the Tape 2 for this weekend backup.. Recently the tape shows '!' at the Tape 2.. when i try to unload the Tape 2, it shows me no tape is load.. wat does the '!' means?? can anyone explain? is it the tape is bad??
this is wat it shows when i mt staus
HP Ultrium LTO 2 tape drive:
sense key(0x6)= Unit Attention residual= 0 retries= 0
file no= 0 block no= 0
can anyone explain..
Thanks..

Hi Surajsid
Do you still have a support contract for this Library ? If it's still showing the same issues after power cycling the drive I would log a call with Orcale/Sun.
Have you changed anything in your backup environment lately ?
Regards
David

Multi-initated LUNS on Sun StorEdge 3310

I recently received two Sun V20Zs and a StorEdge 3310, and I am asked to cluster these two machines with the 3310 as shared storage. 3310 came with two raid controllers.
My question is, could I create multi-initiaged LUNs and have these LUNs mapped by the V20Z. Reason behind having the multi-imitated LUNs is it will facilitate fail-over in case a one of the V20Z are unavailable.
V20Zs are running Fedora Core 3.
Thanks for your help.

A good output that would give you a hint of a problem is iostat -En
This output reports anykind of errors to a particular disk since the last reboot. If you are seeing high error numbers, then you can move onto running a file system check - fsck - on the drive.
If you have anykind of RAID setup, check to see if any issues are being reported. Depending on what you are using to manage the RAID - Veritas Volume Manager or Solaris Disk Suite - they will most certainly tell you if there is an issue. A vxprint for Veritas and a metastat for DiskSuite will show you what you have setup and if there are any recognized disk issues.

Two servers with redundant connections for Sun StorEdge 3320 SCSI arrays

Hello All,
I read in the "Sun StorEdge 3000 Family Installation, Operation and Service Manual" that it's possible to setup "two servers with redundant connections" but I never see a detailed schema to do this. I read also the "Best Pratices Guide" but this case is not mentioned. Is it really possible ?
My objective is to split a Sun StoreEdge 3320 SCSI array between two hosts with dual redundant scsi connection.
Thanks in advance for your answers.
Francois.

At first this sounded easy, but looking at the parts listing for the 3320 seems to indicate otherwise. They're listing different part numbers for the chassis and midplane...
371-0105 chassis & midplane for JBOD
371-0106 chassis & midplane for RAID array
There are also different part numbers for the I/O boards....
370-7655 RAID SCSI I/O module
370-7713 JBOD SCSI I/O module
I can see what the difference is between the I/O modules, but am unsure of what differences if any are in the chassis and midplane. Seems like there's more involved here than what it would be worth to try and make it work. Perhaps the cost of a second HBA would be the lesser of two evils..........

I need books that would help do solaris 10 CX-310-200 and CX-310-202 exam

hi i want to do solaris 10 system administration exam anyone has book that would help me do CX-310-200 and CX-310-202 exam?

Bill Calkin's Solaris Administration books are very helpful for these exams. Also you can use Solaris Admin Collection which can be found from this link: http://docs.sun.com/app/docs/coll/47.16
Good luck to you!

Sun Storedge 3310

I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2? If ther is could you tell me how. I know how to do it on server 2003 but 2012 r2 is much different.

Hi,
I would like to know if it is possible to connect a sun storedge 3310 array to windows server 2012 r2?
Since we are not familiar with the product you have mentioned, I would suggest you contact corresponding vendor support to get more specific and accurate response.
Thank you for your understanding and support.
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Netra T1 (200) and Sun Storedge D1000

Similar Messages

Maybe you are looking for