Network access enabled trying to connect bluetooth with iPhone 5

im trying to connect iphone 5 bluethooth with my macpro and it keep saying ''make your network access enabled''

You cannot use BT for file transfer.
See the support BT profile:
iOS: Supported Bluetooth profiles - Apple Support

Similar Messages

Mac Loses Network Connection while Sleeping (Wake for Network Access ENABLED)

I have "Wake for Ethernet network access" enabled in my Energy Saver preferences. However, it appears that my Mac disconnects from the network entirely when it sleeps; therefore, this does not work when I am trying to connect while it's asleep.
I suspect this because it always takes a moment to connect to the network when I wake it up. Webpages don't load until about 30 seconds after the computer wakes up. I can't connect to my Mac over the Internet (with my port forwarding enabled) anymore, which is a big problem.

The article isn't very clear, but I've seen from a Google search "wake on LAN on Mac" that people think that the setting in Energy Saver enables simple wake on LAN as well. Maybe it does both. Wake on Demand has the advantages of advertising the sleeping Mac's services via Bonjour and responding to pings without waking up the sleeping Mac.
To be honest, I hardly know how Bonjour works, just that it's used to discover Apple devices on a network and that it gives each Mac an alternate hostname that you can use (for example, Bobs-Mac-Pro).. It seems like the Bonjour Sleep Proxy would only work if you're connecting via Bonjour to the Mac. If you connect directly by the IP address (192.168.1.12 for example), the router must send that straight to that Mac and not through a Bonjour Sleep Proxy (because how would it know to look for a BSP?). I tried connecting by address to my Mac from a computer on LAN while my Mac was asleep, and it woke up. It used to do that over the Internet, but now it doesn't, which is my problem. I was going to take it a step further and cut out any Bonjour Sleep Proxies totally by connecting the computers directly with ethernet, but that caused my Mac to refuse to sleep at all.

HT5706 I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any help?

I just purchased an AppleTV and am trying to connect AirPlay with my mac (2012 model) In 'system preferences > displays' an airplay menu is listed but it says 'no device detected'. My AppleTV and macbook are connected to the same network. Any suggestions why it is not working?

Troubleshoot the network as that is likely what is causing the issue.
Also, temporarily disable the firewall on the Mac and disable IPV6 on the computer.

Can I use Apple Magic Mouse with my IPAD2, have tried to connect them with Bluetooth without success

Can I use Apple Magic Mouse with my IPAD2, have tried to connect them with Bluetooth without success
Dag Ove

I suggest that you request this feature, as I have, at Apple's feature request site. Maybe if enough of us request this it will come in a future iOS release.
http://www.apple.com/feedback/ipad.html

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet.

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet and it could not detect the the ip address after i input the correct address on "Connect to Server" window. Please help! Urgent! Thanks

I did not say it is not possible.
I said if your company networks are monopolizing both ports, you should talk to them about what options are available.
Maybe you can get the company Intranet over wireless if you change some configuration items such as Subnet Mask.
Maybe you can get on the Internet over Ethernet.
You really need to ask them, and do not let them blow you off because you have a Mac. If they balk, ask them how it would be done on a PC (becasue it will be the same on a Mac).

Hello, I currently have a MacBook snow leapord and i'm trying to connect it with my Canon MP560 printer, i put in the CD and installed everything properly but now when i add a printer it says a Queue already exists, i click continue and nothing happens???

Hello,
I'm using a MacBook Snow Leapord and I'm trying to connect it with my Canon MP560 printer/scanner.
I installed the CD and followed along with the manual and did everything it asked, at the end it told me it was finished.
So then I went to go print something and an error had occured so i went to the file menu on Microsoft Word for
Mac and clicked Print/Add Printer and then i click on the Canon MP560 series-1 as it was the only one to click on.
When I did it stated that I already has a Queue for this printer and if I'd like to add a new one so I clicked continue and nothing
had happend. PLEASE HELP
sincerely,
Laura.

I would recommend to download the driver appropriate for your system from the Canon webiste or, after installing it, to run software update and it will detect it for you.
If you have the last driver appropriate for your system, you may wish to reset the printing system. To do this, go to Sys prefs/print and fax and, upon clicking minus button, also press Option/alt key. You will be asked to confirm, do it. Then, add the printer by pressing plus button, it should work now.
But, before doing this, download the last good driver, CDs usually contain outdated drivers.

HT1414 after restore i reached in the "choose a network" than i trying to connect to itunes but it could not work forword ..what to do..please tell??

after restore i reached in the "choose a network" than i trying to connect to itunes but it could not work forword ..what to do..please tell??

after restore i reached in the "choose a network" than i trying to connect to itunes but it could not work forword ..what to do..please tell??
iPhone 4

My July 2009 iMac with OSX Mavericks "iMac is not supported" when I tried to perform bluetooth with my iPhone 5. What is the problem. thanks

My July 2009 iMac with OSX Mavericks "iMac is not supported" when I tried to perform bluetooth with my iPhone 5. What is the problem. thanks

Bluetooth is only supported for tethering.
Barry

IPad won't Bluetooth with iphone

iPad won't Bluetooth with iPhone 4s

Hi kalidongnv,
Thanks for visiting Apple Support Communities.
These troubleshooting steps can help if your iPad won't pair with your bluetooth speaker:
Check that you are in range of the Bluetooth device with which you are trying to pair your iPhone, iPad, or iPod touch. Most Bluetooth devices have a range of approximately 30 feet.
On your iOS device, tap Settings > Bluetooth and find your device in the list. If your device says Not Connected, tap the name of your device to attempt to connect it.
Tap Settings > Bluetooth and turn Bluetooth off and then on again.
Make sure that your Bluetooth accessory is turned on and fully charged or connected to power.
Restart your iOS device.
Tap Settings > Bluetooth and locate the Bluetooth accessory you are currently connected to or attempting to connect to. Then tap and Forget this Device. Try to pair your Bluetooth accessory again.
Note: You may need to re-enter your Bluetooth accessory PIN if your accessory requires one. Some common PINs are 0000, 1111, and 1234.
Restart your Bluetooth accessory by turning it off and then on again1.
Update your device to the latest version of software. See how to update your iPhone, iPad, or iPod touch.
If your Bluetooth accessory has upgradeable firmware, check to see that you have the latest version1, 2.
The steps above can be found in this article:
iOS: How to troubleshoot Bluetooth connections
http://support.apple.com/kb/TS4562
All the best,
Jeremy

Trying to connect my replacement Iphone 3GS to my windows 7 laptop but it is not recognised at all, my ipod can connect no problem, my iphone can connect to my windows vista computer no problem. Any ideas?

Trying to connect my replacement Iphone 3GS to my windows 7 laptop but it is not recognised at all, my ipod can connect no problem, my iphone can connect to my windows vista computer no problem. Any ideas?

More info,
I have bootcamp with Windows 7 installed, do I need to run some "Driver compatibility checker" after the Windows 7install?
if so what is the name of it?
thanks

Is there a fix for the connectivity problems with iPhone 5S and ISO 7.0.2?

Is there a fix for the bluetooth connectivity problems with iPhone 5S and ISO 7.0.4?
I am having problems connecting the BT Audio and the handsfree phone connectyion is unreliable in 2012 Mitsubishi Lancer XL.
All worked OK with ISO 6.

Hello CraigNicholson
You would need to sync with iTunes to get that process to work for you. Check out the article below for more information on how to resolve that issue to get the proper token to use Push Notifications again.
iPad and iPod touch: Unable to use YouTube or Push notifications
http://support.apple.com/kb/ts3305
Regards,
-Norm G.

My Sennheiser MM550-x connected perfectly with iPhone 4s. It does not connect with iPhone 5s bluetoth. Ayone else with this problem?

My Sennheiser MM550-x connected perfectly with iPhone 4s. It does not connect with iPhone 5s bluetoth. Ayone else with this problem?

Hey araho!
Here is an article for you that will help you troubleshoot this Bluetooth issue:
iOS: Troubleshooting Bluetooth connections
http://support.apple.com/kb/TS4562
Thanks for using the Apple Support Communities. Have a good one!
-Braden

Trying to do minimovies with iPhone. I tried combination "FourTrack"

Trying to do minimovies with iPhone. I tried combination "FourTrack" & "iMovie" but the created soundtrack could not be imported to iMovie. Is there any iPhone multitracker wich is compatible with iMovie?

Put your iphone in dfu mode by doing this. Turn your iphone off. When its off, hold home and power button together for exactly 10 seconds, then release the power button and keep holding home button for another 10 seconds. Then open up itunes on your pc and plug your iphone to your pc. Itunes should recognize your iphone in recovery mode and it will tell you to restore it. Click restore, and your iphone will restore. Remember that, if you do this you will lose everything that was on your iphone. You can restore from backup later on. Hope I helped. If you have any questions or problems with this tutarial, you can contact me personaly on my email [email protected] . Hope I helped. Cheers

How do I avoid having to pair my bluetooth with iPhone 4 every time I use it?

How do I avoid having to pair my bluetooth with iPhone 4 every time I use it?

I think I didn't make myself clear. My bluetooth device is paired. If I turn the device OFF while keeping it ON in the iPhone 4, and later on come back and put the device ON, the iPhone doesn't find it. The solution is to turn it OFF in both the bluetooth device and the iPhone and start again, which was not the case with my previous iPhone 3 and is a real pain to have to do this each time... Any one familiar with this? Thanks in advance.

How do i turn on network access protection on windows 8.1 with an hp p6-2326S pc?

i got a phone call from a unknown source today at around 3 pm they said that hackers where trying to access my computer . they ran a scan and it showed thre things one was my network access protection was turned off . 2 hackers were trying to hack into my computer i cant remember the 3rd one its in my note pad but then i got this big run around and i told them from the start that i had no money and that i had just buried my mom on the 2nd of this month after a long battle and that i had just had a bad episode with my blood pressure wasnt feeling god and so on ,all of which are true once i finally convinced the worker of the fact i had no money he put his super visor on the line .the supervisor was stalling i could tell im no dummy when it comes to software and computers i taught myself xp professional and the windows 8.1 which im still learning i finally got tired of his super visor retstartd my computer and got control uninstalled skype mozilla nightly and mozilla experimental and several other prorams with my revo pro uninstaller my computer is rinning smooth now but i have seen .that ny network access protection is turned off ,how do i turn this on and is it neccasary i have malware bytes new 2.7. something full time bought and paid for protection and windows defender .i run a discclean every day and my mal;ware bytes and windows defender any thoughts and ideas would be appreciated i do have HP SUPPORT ASSISTANT AND MY WARRANTY IS UP TO DATE AND PAID FOR .. sincerely donald hutchison

dhutch1 wrote:
i got a phone call from a unknown source today at around 3 pm they said that hackers where trying to access my computer . they ran a scan and it showed thre things one was my network access protection was turned off . ...
Hi,
Now the trouble may start, you did allow people to logon to your computer and you believe them ! HP Support Assisstant is there to support your technical problems it does not know you will open the door of your house for someone to comes in to steal your money.
Now, please change all your passwords to logon to email, bank account(s) ..... before too late. Also please download the following tool nd run on your computer, hope it can remove the nasty bits.
Good luck.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Network access enabled trying to connect bluetooth with iPhone 5

Similar Messages

Maybe you are looking for