Network adapter re-install

hello. my computer stopped connecting to the internet. after hours of troubleshooting i learned it was the broadband adapter. i followed advice to uninstall via device manager. restarted and still no access. my computer is hp mini 210-2100. broadcom lists 4313802.11b/g/nand PCI\VEN_14E4&DEV_4727&SUBSYS_145C103C&REV_01is there somewhere i can download a new version to a flash drive to then install on my computer?ORcan you please help me.thanks!

Depending on which Windows 7 OS is being used, here is the driver for 32-bit:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-77712-1&lc=en&dlc=en&cc=us&...
and here is 64-bit: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=4065...
Try to install the appropriate driver after first going to Device Manager to verify the fact that no network adaptor is detected. Since the device is part of the motherboard, the driver is either not installed properly or the device has failed. If there is no entry under "network adapters" instead of an exclamation mark, then the device may be defective. A PCI or PCIe network adapter can be installed if there is an open slot. Otherwise a USB adapter is possible.
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP.

Similar Messages

Error while installing network adapter driver on HP ML 370 G4

We have HP ML 370 G4 server. And I get an error while installing driver for embedded network adapter on Solaris 10.
I don't know what to do...
Can anybody help me??
# pkgadd -d /tmp/BRCMbcme.pkg
The following packages are available:
1 BRCMbcme Broadcom NetXtreme Gigabit Ethernet Adapter Driver
(i386) v7.5.12
Select package(s) you wish to process (or 'all' to process
all packages). (default: all) [?,??,q]: 1
Processing package instance <BRCMbcme> from </tmp/BRCMbcme.pkg>
Broadcom NetXtreme Gigabit Ethernet Adapter Driver(i386) v7.5.12
Copyright (c) 2001-2003 Broadcom Corporation, Inc.
All rights reserved.
This product is protected by copyright and distributed under
licenses restricting copying, distribution and decompilation.
Using </> as the package base directory.
## Processing package information.
## Processing system information.
6 package pathnames are already properly installed.
## Verifying package dependencies.
## Verifying disk space requirements.
## Checking for conflicts with packages already installed.
## Checking for setuid/setgid programs.
This package contains scripts which will be executed with super-user
permission during the process of installing this package.
Do you want to continue with the installation of <BRCMbcme> [y,n,?] y
Installing Broadcom NetXtreme Gigabit Ethernet Adapter Driver as <BRCMbcme>
## Installing part 1 of 1.
/kernel/drv/bcme
/kernel/drv/bcme.conf
/usr/share/man/sman7d/bcme.7d
[ verifying class <none> ]
## Executing postinstall script.
("pci14e4,1644") already in use as a driver or alias.
postinstall: add_drv bcme failed
pkgadd: ERROR: postinstall script did not complete successfully
Installation of <BRCMbcme> failed.
#

If you're sure that you have a Broadcom BCM57xx
device installed in the machine, then you should have a look at
"prtconf -pv" output, locate the Ethernet device, and check the
"vendor-id" / "device-id" property for the NIC.
If the Broadcom device is compatible with Sun's "bge" driver, you
can try to install an addition driver binding entry for your device,
using the update_drv(1M) command
update_drv -a -i '"pciVVVV,DDDD"' bge(where VVVV and DDDD is the pci vendor / device id found in
prtconf -pv output).

Unable to access the internet on windows xp using bootcamp. I installed the bootcamp drivers ( from snow leopard) but it still doesn't work. I have parallels 6 also installed and IT works fine. I am missing a rtl network adapter-thanksr

Hi
I have a new 21 inch imac oct 2011 version. I installed bootcamp and windows xp on my machine and i also installed parallels 6.
Paralleles works great and i can open any program with it. But bootcamp also works EXCEPT it refuses to give me access to the internet. I installed the bootcamp drivers from my snow leopard disk, it did not make a difference. All the drivers installed but still no internet. I then installed the bootcamp drivers from the gray mac osx disk (#1) but it stopped installing with an error number ( 2753) and it said that the package was damaged.
I have tried everything; i opened each disk and trieed installing the files separately. Nothing.
What i see missing in my devices screen in XP is the network adapter.
I have a router (dlink-dr615) and it is connected by ethernet to my imac. I wonder if THIS might have anything to do with the problem. Any guidance would be much appreciated.
Thank you

I'd recommend reposting in the Boot Camp forum, that is where the Boot Camp and Windows gurus hang out.
Good luck.

Surface Pro 3 / "Windows did not detect a properly installed network adapter"

Hi all,
I've been running the Windows 10 Technical Preview (9926) on my Surface Pro 3 successfully
since January. Unfortunately, I lost all internet connectivity today.
The problem started when I noticed the type cover wasn't working (pressing keys on the type
cover wasn't registering any typing on my screen) and my USB mouse wasn't working either. I tried removing and reattaching the type keyboard but this didn't fix the issue. I had to use the accessibility on-screen keyboard to sign into Windows (thankfully touch
was still working). Once I signed in, I still didn't have typing or cursor ability, so I decided to restart the computer.
Then it got worse. I noticed the Surface Pro 3 was stuck on "restarting" and wouldn't
actually restart. Since it wasn't responding, I held down the power button for about 10 seconds until it turned off. When I turned it back on, the type cover and mouse started working again.
Unfortunately, this is when the WIFI problems began. I had WIFI for a few seconds, and then
I lost internet. I disconnected/reconnected but there was a yellow triangle telling me there was some sort of problem. So I restarted the Surface Pro 3.
When it came back on, there were suddenly NO connections available at all. Opening the "Network
& Internet" settings page gave me the message "Windows did not detect a properly installed network adapter". And here I am, without internet on my Surface Pro 3, borrowing my friend's computer so I can type this message (he is also running
Windows 10 build 9926 on his laptop and is able to connect to my WIFI with no problems, whereas my Surface Pro 3 cannot even detect any networks). I have not dropped or damaged the SP3 in any way, and there have been no storms or power outages or anything
of that sort. Any ideas what could have happened to the WIFI on my Surface Pro 3?
Thanks for your help...
Ethan

Hi Ethan,
Currently, there are a few compatibility issue between the current hardware and Windows 10 Technical Preview (9926 build), this is mostly related to driver compatibility issue.
I suggest you download the latest network adapter driver package to install, when it is finished, check if it appears under Device Manager.
Surface Pro 3, Surface Pro 2, and Surface Pro firmware and driver packs
https://www.microsoft.com/surface/en-us/support/networking-and-connectivity/install-wireless-drivers
You can check if you can install the latest firmware package for your device.
Here is an article to talk about such things:
Windows 10 January Technical Preview on Surface
https://www.microsoft.com/surface/en-us/support/install-update-activate/windows-technical-preview#Known
Regards,
Alex Zhao
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

How to install microsoft hosted virtual network adapter

I have a HP 20- A225IN windows 8.1 All in one PC
I accidentally uninstall the Microsoft hosted virtual network adapter from Network Adapters under Device Manager.
please tell me how to install this adapter again?

I have a video that covers the steps to install the Microsoft Loopback Adapter in Windows 7. Hope this helps...
http://www.youtube.com/watch?v=R9674zGHxrE
Guides and tutorials, visit
ITGeared.com.

How to install network adapter driver?

My Dell xps internet was working fine yesterday (wired connection) but then all of a sudden the internet stopped working even though the cat6 was plugged in to the router. I tried different cables to see if the cable was faulty but it turns out that my network adapter is missing a driver. I checked what network adapters are inside my motherboard but its come up with like 12 different network adapters. How do I know which one i should install the driver for? Also where can i find the correct driver to install?
I should also note i set my pc back to a date which it was in 4 years ago since it was really slow and i wanted to improve its performance.
I searched all over the web to find solution to my problem but none of the solutions at hand worked. 1 solution was to change the properties on my "Local Area Connection" but i haven't even got "Local Area Connection" icon for some reason (i have never seen a computer not have this icon before". It is like my computer is completely not picking up the connection from the router and even worse its as if its repelling it...
Anyways, signed up to this forum to see if one of you guys could help out :).

Sorted it now. Had to go into BIOS and enable internet connection.

Apple itunes installed network adapter and wiped my wireless out

On Windows Vista x64, I tried to take the update for itunes and it said it failed, to try download only (which has not been working either for me over past year; I always have to uninstall and go to the site to download/install it myself). But my internet stopped working 5 days ago (my wireless adapter inside laptop cannot find any networks ever; nor did my ethernet connection work to overcome this) and my first line of defense was to use sys restore; low and behold, there was an entry for the time period it stopped working that "apple network adapter installed" but no matter which restore point I tried to use anywhere around that event, it always came back with errors and stated no changes were made; still no internet either.
I have uninstalled the hardware thru device manager and tried to let windows reinstall it with drivers, but that doesn't fix it either. I even downloaded onto a flash drive the original driver that has since been updated by Intel for my Intel Link 5100 wireless adapter, but still it will not work. The ethernet did start working once I installed the old original driver for it, but even last night I got the error while plugged into my router "limited connectivity" meaning no internet. I then tried uninstalling all apple programs and kept being blocked from doing so (sounded viral to me so I ran norton power eraser, spoke with support, even used couple other programs for spyware malware bootkit/rootkit etc). Now I finally got all the programs uninstalled, cleaned the registry, and still I cannot get the wireless adapter to work.
I have spent days on this issue, seeing other discussions over the past few years where this has happened before (an update with apple's network adapter installs and wipes out the actual hardware adapter) but each time it only affects certain models of wireless/ethernet adapters. Guess this update got mine. I am trying NOT to have to restore my computer to factory condition as it is over 2 years old and that will mean millions of updates to all microsoft programs, drivers, etc.
Does anyone have any ideas that will fix this? I can send you my specs if you need them.
Sheila

Thx for the suggestion, but this is the post I originally found and figured out what went wrong, However, as I stated in my question post, I have not only uninstalled, scanned for hardware changes (w/o reboot) and rebooted and watched windows install device drivers for both lan & wifi, yet the wifi absolutely will not work now. I have the ethernet working since installing the old original driver, and today I was able to actually get back up to the last wifi driver from intel I had before itunes wiped it out. But still no wifi. My intel program and intel's system checker I used on their website states:
WIRELESS NETWORKING INFORMATION
Wireless Networking Product
Intel® WiFi Link 5100
Driver Version
13.4.0.9
Intel PROSet/Wireless Version
not detected
Software/Driver Status
Newer Driver Available
Latest version available
13.5.0
Hardware IDs
PCI\VEN_8086&DEV_4232&SUBSYS_12018086&REV_00
and I can't get the Newer driver to install without errors stating it will not work with my ACer setup. But at least I got from v12.0.0.73 today to the one above. I reinstalled Itunes today hoping that would fix anything I'd removed and the version was like 10.3.x.x.x. Then I uninstalled from device manager & rebooted hoping wifi network adapter would start working again, but alas, no..
Hope someone can help me soon, cause I've run out of ideas.

IMac Running Windows 7 can't 'detect a properly installed network adapter'

I just put windows 7 on my brand new iMac 27'' i7, but to my surprise I cannot connect to a wireless network, and when I go to the trouble shooting section it says-
"Windows did not detect a properlu installed network adapter. If you have a network adapter, you will need to re-install the driver."
Help me to connect to the internet please.

Install the Apple drivers; read the guide.
You should have Lion so you would have Boot Camp 4.0
Boot Camp 4.0 Installation & Setup Guide OS X Lion
Boot Camp 4.0, OS X Lion: Frequently asked questions

Yoga 2 did not detect a properly installed network adapter

Woke up this morning, turned my yoga 2 on, no WiFi. So I used the troublsheeter and it told me there was no properly installed network adapter. Does that mean my wifi card is dead? Anyone else have an issue like this and find a solution (besides replacing a dead card?)
I did:
1) reinstalle drivers via usb from another machine
2) used a system restore point from a few days ago
Neither action had any effect.

Well I just set it to airplane mode and while I had no wifi it never told me that there was no network adapter cofigured.
Also, when you set it to airplane mode the wifi signal icon changes from bars to an airplane.
I think the adapter must have stopped working and then.. started working again. I can't figure out what else it could be.

Portege R700 PT311A - Network Adapter needs to be installed

My Toshiba Portg R700 (PT311A-06600Q) will not connect to the internet.
It says that a Network Adapter needs to be installed and configured, but I do not have the disc to do this, nor do I have an internet connection on my laptop to download the driver.
I have attempted to download the driver onto a USB, using another laptop, then using that USB, I have tried to install it onto the problem computer, but it won't install.
There is no Windows installed on the problem computer, may this be an issue as to why the driver won't install?
Help me, please!

Hi
I hope you picked up the right driver.
Not quite sure if you are talking about LAN driver or WLan driver and what Windows system you are using but fact is that all drivers for this unit can be found here:
http://www.mytoshiba.com.au/support/download
I would recommend you to check once again if you downloaded the proper driver. Then move the driver package to the notebook (desktop). Unzip the package and execute the setup or install exe file.
In case you would not find any exe files in the package, I would recommend you to install the driver within the device manager.

In Order to Configure TCP/IP, You Must Install and Enable a Network Adapter Card

I get this message when I try to TCP/IP settings in any network card.
"In Order to Configure TCP/IP, You Must Install and Enable a Network Adapter Card"
What I have tried:
1. Removed card, did not click on "Remove driver". Then re-scanned in device manager. This usually leads to the network card showing up with a yellow exclamation mark, and I can not get it work again (have to use system restore).
2. Removed card, deinstalled driver, re-installed driver.
3. Rebooted a thousand times.
4. Used the Lenovo drivers.
5. Used the Intel drivers.
Doesn't matter what I do, I'm stuck with yellow exclamation marks in the end for the LAN and WLAN card, with not hope to repair them.
Driver version for the Intel 82579LM is 12.9.15.0
Driver version for the centrino advanced-n 6205 is 15.10.4.2
I'd really like some help on how to fix this so I'm able to configure my network manually.

For clarity, as your machine MTM number lists it with another type of WLAN adapter, and apparently, therein lies your problem.
How To Fix Error Message : In Order To Configure TCP/IP , You Must Install And Enable Network Adapte...
[How To Fix] In Order to Configure TCP/IP, You Must Install and Enable a Network Adapter Card
ThinkPad W540 (20BG) - i7-4800MQ/24GB // ThinkPad T440s (20AQ) - i7-4600U/12GB
ThinkPad T440p (20AW) - i7-4800MQ/16GB // ThinkPad Helix (3698-6EU) - i5-3337U/4GB
ThinkPad W520 (4282-W4Q) - i7-2720QM/32GB // ThinkPad T400 (2767-W1C) - P9500/8GB
ThinkPad T61 (7665-CTO) - T7700/4GB // ThinkPad T60p (8741-C2G) - T7400/4GB

After Installing Oracle Virtual Box and changing the network adapter to bridged mode cant access my server

Hi ,
I have installed Oracle Virtual box on windows server 2008 r2 hosted on 1und1.de.
Till installtion and setting up untun on virtualbox it was fine, but once i changed the adapater to bridged mode. I immediatly lost connectivity with my server and now cant access.
It is now 2 days i cant access my server and neither ping it, also the website hosted on it is also down.
The 1und1 has following 2 options
1) using putty i can connect to server command prompt using administrator but cant run any gui application
2) Server Rescue mode: where i get special environment to start, stop services, access registry and command prompt.
Till now i have tried lot of setting to enable network connectivity but not able to success
This is the result of Ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : s15453760
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter VirtualBox Host-Only Network:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter
Physical Address. . . . . . . . . : 08-00-27-00-04-FD
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::5d5c:5bbc:c61:e9b1%16(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.233.177(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 352845863
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-15-B9-51-EA-00-19-99-A5-E7-BE
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.{BBF9AA14-45EA-460C-8F23-E106D890D878}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter 6TO4 Adapter:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 12:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
How can i restore my connection.
Thanks

Hi,
According to the result of "ipconfig /all", the physical adapter dosen't appear.
Please check if the physical network adapter works properly. We can verify this in Device Manager.
To open Device Manager by using the Windows interface
Click Start, and then click Control Panel.
Click Hardware and Sound.
Click Device Manager.
If the network adapter is working properly, please make sure that the Internet Protocol Version 4(TCP/IPv4) has been checked in the properties of the physical network adapter.
If issue persists, please try to uninstall the Oracle Virtual box.
Best Regards.
Steven Lee
TechNet Community Support

Hyper-v Client in Win10 Enterprise Technical Preview does not boot to PXE via Leagacy Network Adapter after OS is installed using gen 1 BIOS

Using Hyper-v within Windows 10 Enterprise Technical Preview to boot a Win 7 Legacy BIOS (Generation 1) Operating system client does not boot to PXE legacy network adapter after operating system has been installed within the Virtual Client.
Hyper-v Client will boot to PXE Legacy Network Adapter only when no other boot device is available and no OS is installed.
Hyper-V settings seem to ignore BIOS - Startup order within Hyper-V Client Settings and will always boot to VHD before Legacy Network Adapter even if Legacy Network adapter is first in the startup list.
IF VHD is deleted and a new VHD added to the Client then will boot to PXE using Legacy Network Adapter. Again once OS is installed then will not boot to PXE Legacy Network Adapater.
Gen 2 BIOS/UEFI works as expected and boots to PXE network everytime.

Hi shaunmoncrieff,
Thank you for the information.
Currently I am not available to take a test using Windows 10 on physical machine.
You may try to submit this information through Windows Feedback Tool, once I have tested, I will update the results here.
Best regards
Michael Shao
TechNet Community Support

G4 Won't Boot after Tiger install and Belkin USB Network Adapter install.

I'm sure this would apply to my G5 as well.
I installed Tiger on my G4 and it restarted and opened to desktop. Great!
Next, installed software drivers from Belkin USB Network Adapter.
Restarted computer,
Screen has firmware 'like" look asking me to type mac_boot.
I do this and the next screen is all grey with two small purple folders in the corner. I believe one was flashing!
Nothing happens just stays there.
How can I get back to normal boot mode?

tigerswim, welcome to Apple Discussions.
Did you already have Tiger installed or did you have Panther 10.3 installed? Tiger is not a free upgrade; you have to buy it & then update (for free) using the download updates from Apple. Also, you have to use a universal/retail install DVD (or CDs) to install Tiger. You cannot use the install DVD from another model Mac.

I cannot connect to internet im getting the error message: no network adapter installed or configure

i cannot connect to internet im getting the error message: no network adapter installed or configured. what can i do?

Sherya, welcome to the forum.
When requesting help, you should always include the make/model of the computer and/or monitor. This information is necessary for us to review the specifications of them.
I believe that this is a problem for your ISP. Their Customer Service should be able to help you. There may be some settings that can be changed to solve the problem. They would know what the settings should be. I don't believe that it is a hardware problem.
Please click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Network adapter re-install

Similar Messages

Maybe you are looking for