Network card integrated with motherboard

Hi!
Is the network card on a HP dv7-3130eo integrated with the motherboard?
My networkcard is breaking down, and I get bluescreens often. Now I only use the cable to get online. I've installed the latest drivers and I am almost sure that the hardware is the problem. Is this a common problem?
/Simon

DonSimon11 wrote:
Hi!
Is the network card on a HP dv7-3130eo integrated with the motherboard?
Hi,
You can use Device Manager to work this out, under "Network Adapters". BUT I believe it can be Broadcom or Realtek (which is NOT integrated with the motherboard).
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Network card problem with Mobo make the computer crazy!!!

Im using a msi 745 Ultra version 10/cpu xp2400/basic graphics card/40gb HD, 256mbs of drr
I have tryed 2 networks cards both with the same results & even changed mobo & ram/graphic card/HD.
The computer seems to work fine untill i decide to put in a NIC.
It starts to post the wrong processor speed/screen decides not to display sometimes & takes a little longer to boot into windows. It will also some time crash when i turn on the computer. If i try to save something in the bios it will then reboot & then try to boot of the floppy drive.HD / CDrom drive but will not find them.This has happend on both mobos.
This is a very odd problem im getting need some help ASAP.

Sorry Bakes...folks aren't just waiting arount to help you. Expecting an answer in 2 hours is placing to high of an expectations on a user to user help forum.
No one here works for MSI, we are all users, just like you.
If you have not seen a reply, then there are several reasons that may affect why there has been no reply.
No one knows, or can offer o good answer to you question.
The question is too general and you did not supply the necessary information someone might need to even begin helping you. I have provided the basics on what we need at the top of this forum.
No one may be familiar with your motherboard's chipset, perhaps someone is but they have not visited the forum lately.
I can give only some general tips to consider for the time being.
Some incompatabilities may exist with a certain NIC card.
Check PCI slot IRQ sharing conflicts. Typically I stay to the middle slots and avoid the first and last. You may have to power down, move the card to another slot, and power back up. Each time checking your IRQ's in either Device Manager or System Information to see that the card is on its own IRQ.
Improper BIOS settings can cause conflicts.
Try "Plug and Play Aware OS" set to "No" and let the BIOS manage things or set it to yes and let Windows do it. In most cases it has been recommended to be set to no.
Upon installation of new hardware the setting "Reset Configuration Data" can be useful in avoiding lockups after POST due to conflicts recognized during "Verifying DMI Pool Data"
Possible reasons: Hardware change, BIOS settings change, improper connection of IDE cables, corrupt MBR (Master Boot Record) of the HDD (Hard Disk Drive), defective HDD or defective mainboard.
Possible causes: Hardware incompatibility, virus attack, electric circuitry damage/defect, corruption of data, improper BIOS settings, over-clocking damage.
*NOTE* Some Chipsets do not support this feature, see manufacturers documentation.
That's about all I care to share for now.
Good luck........

Steps: SNC (Supplier Network Collaboration) Integration with ECC through XI

Hi,
Has anyone worked on the SNC(Supplier Network Collaboration) integration with SAP ECC via SAP XI.
Could you pls share any documentation related to this. And also could anybody tell me the setup required to go ahead with the integration.
Thanks,
S

Hi Xavier,
SNC integration with XI has predefined mappings. So ask your basis guys to download the XI content for SNC using with PI. Once they deployed you will have a builtin predefined content in XI. Within the predefined content mostly they all are xsl mappings.
If your requirement is with the standard idocs then you can use them directly. Else if their is customization they you may need to change the mappings according to your requirements.
Also check this help:
http://help.sap.com/esoa_scm_snc2007/helpdata/en/index.htm
Regards,
---Satish

Integrated Network card problem with K7N2 Delta-L

my integrated network card doesn't recognize any RJ45 cable bluged to it !!!
"ofcourse i enabled it from Bios"
the card is identefied by windows normally as nVidia ethernet ......
i tried to change the version of nForce driver but no way.
i pluged a normal PCI network card and work well with the LAN ... unpluged & re connect the integrated one with same cable but no way .. the task bar icon told me that A CABLE IS UNPLUGED >>
plz help

hi
what do you tru to connect it to?
i cant use onboard lan with my cable modem but a friends router worked without trouble.
btw welcome to this forum
bye

Which network cards works with Solaris 8?

Hi,
I am installing Solaris 8 on a PC but I am having a problem finding a network card that the system will recognise.
I have tried HP and Intel cards but always see the error message "iprb: iline value out of range: 255"
Is there a particular brand/model of card that I should get?
Any help would be much appreciated.
Jon

Hi,
You refer this URL: http://soldc.sun.com/support/drivers/hcl
Here you will get the compatibility list for solaris 7 and solaris 8 versions.
revert back.
Thanks.
regards,
Senthilkumar
SUN - DTS

SAP SNC Supplier Network Collaboration integration with SAP ERP via BizTalk - experiences?

Hello,
had anybody experience in integration of SAP SNC Supplier Network Collaboration with SAP ERP via BizTalk Server?
Versions: SAP ECC 6.0 Ehp5 SPS11, SAP SNC current version (7.0?)
We will have to integrate following processes:
Master Data integration, PO Purchase Order, Forecast, SMI Supplier Managed Inventory
Usually SAP takes an SAP PI middleware for this, where the full implementation can be downloaded from the SAP marketplace, but we want to avoid having an additional Integration Platform with maintenance etc.
Are there experiences, success stories, pitfalls, issues to be known, recommendations, known efforts in this forum?
Thanks in advance.
Jens

HI Jens,
In our forum, we discussed topic about BizTalk & SAP Integration before, hope it helps you.BizTalk
& SAP Integration
Best regards,
Angie
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How to Smart Card integrated with database ..im beginner

Dear,
im beginner for Technologies Smart Card.. I have ACOS2 and reader ACR30D ..I hope u can helping me..please my question?
1. How to java or Visul Basic integrated and presenting data on file in card (like name, address, phone number, ..etc)?
2. Please give me sample project in Visual Basic..?
its just for finnal test me.
Thanks for all
Best Reagard,
[email protected]

hello,
Check the section titled Reference Implementation on this page out.
http://www.opencard.org/index-downloads.shtml
Also if you really need codes in VB, this guys have stuff like that
http://www.motechno.com/x509-sdk.0.html
Tha development kit MAY be all you need
All the best,

Network card: e1000g (Intel PRO/1000 MT) did not working properly

Hi to everyone!
I'm having some strange trouble.
All computers attached to one DLink gigabit switch
Server #1:
nf4-based motherboard, Intel PRO/1000 MT net card, onboard net card (forcedeth driver used) Ubuntu Linux 2.6.25 kernel version.
All just working.
Server #2:
nf6-based motherboard, same Intel net card, SunOS 5.11 snv_86.
All just working.
Server #3:
Same as server's #1 nf4-based motherboard. Same onboard card. Same SunOS 5.11 snv_86 as server #2 have installed.
Its work. BUT..
Intel card is not working as expected.
It is seen by system. It is properly up and running. It is sending packent and receiving packets. Ierrs=Oerrs=Collis=Queue=0.
But thru e1000g0 interface no one computer can reach this one, and from server #3 no one computer is seen thru e1000g0. Exept...
Except two old Sunray1 devices (attached to the same switch for testing purposes)! But even these devices seen only by arp requests, and is not pingable.
It is some mistery, but if I turn on jubmo frames, these rays got a picture from SRSS, testing on this sevrer! Not for long, heh, they hung up fast, but this is proof a physical connection :)
So, I can not disable onboard network card on Server #3 - server becoming unreachable :(
I know, those network cards must work on Solaris - as they did it on server #2. I know, those network cards work with my nf4-based motherboards - as they did it on server #1.
But I can't uderstand, whait is going on with e1000g driver on server #3!
P.S. Kernel driver e1000g settings are the same. All difference from servers #2 and #3 is: #2 had Intel netcard installed then Solaris was setting up, and #3 had Intel netcard installed later. All netcards are working (I trying to swap them from one computer to another - did not change anything).

*) #3 thinks it is sending, but a NIC/driver error prevents it.NIC is fully health. It is tested on another PC. Driver error - or driver's bad implementation - is the one I'm thinking.
*) #3 has a bad transmit pair of wires (would affect all communication)This patchcord works w/o problems on other PCs and even on onboard NIC of server #3.
*) Network problemsHeh :)
*) Firewall or other device is dropping the ARP repliesIt is some very stealthy and very selective firewall, affecting only external NICs :)
BTW, then cord is attached to NIC, it sends "who has this IP" requests, asking to be shure there will not be an IP conflict. No one seen this requests.
*) #1 has a NIC/driver error preventing it from seeing the reply.Only for send from #3? It is like a firewall on #3 :) And, there is more PCs, not only #1-#3. No one can see #3's replays (or asks), not only #1..
I'm repeating: this PC works in network now on onboard NIC w/o problems. But onboard NIC is only 100 Mb/s, and we need 1 Gb/s.
I was thinking, Solaris took wrong MAC for NICs - but not, ifconfig shows the same MACs as marked on NICs.
Even more, yesterday i plumbed e1000g1 - second Intel NIC in server #3. And I was surprised - it worked perfectly!
But I make "touch /reconfigure; init 6" - and after reboot, no one of two Intel NICs working again :( They both have the same behavior - no one can see packets they sends.)
I even try to restrict connection on 100 Mb/s by driver's .conf modify - it works, link become yellow instead of green (take a note, NIC is able to "speak" properly with switch!), but all other stay the same.
Strange, really strange behavior. More strange is a fact this NICs work on another instance of same SunOS, but on different motherboard, while the same MB with same NIC is working w/o problems under Ubuntu. Looks like some bug in Solaris driver.

RE: Is there a way to have 2 network cards on the samemachine

Sean,
I mean I am always connecting to the nodemgr of the 2nd environment
successfully. Only when I run the client part of the application that I know
is up, I get a response from the Name Server that it is actually the first
IP address.
I checked again. I defenitely have FORTE_NS_ADDRESS set to IP:5004, in my
case, and not the hostname. I don't have FORTE_LOCATIONS set any where. the
NS_ADDRESS for env2 has only 1 IP address associated with it. My Forte
Control Panel on the client, and hence the NS address has only one entry.
I tried going into escript like you said, and the name service still thinks
it is IP1.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Monday, June 22, 1998 1:31 PM
To: Venkat Kodumudi; 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
Hmmmm? That is a little odd! Let me rehash what I think you are saying.
You now have two environments each with their own name service with
FORTE_NS_ADDRESS set to a different IP:Port combination. For example you
are doing the steps:
FORTE_NS_ADDRESS=255.255.255.1:5000
start the nodemgr for env 1
FORTE_NS_ADDRESS=255.255.255.2:5000
start the nodemgr for env 2
Now when you start a client you are always getting the address for env 1
back from the nodemgr. I assume you actually mean the name service? Or, do
you mean you are always connecting to the nodemgr & name service for env
1?
If the first scenario is the case and you are connecting to the nodemgr
for
env 2 but getting back IP's for services listening on the card for env 1 I
would ask you what you are setting the FORTE_LOCATIONS value to before you
start each service. If you are not setting it or are using the host name
it
will register using the IP for the primary network card associated with
the
machine name and I am again assuming that this is env 1. You need to set
the FORTE_LOCATIONS variable to 255.255.255.2:0 (based on the steps above)
before starting your services.
If the second scenario is the case I would have you check what the
FORTE_NS_ADDRESS is set to before you start up the client. Once again it
must be the IP:Port combination not host:port combination if you want to
get
anything other than the primary card.
I would also suggest that you do the following. After everything is up
and
running execute the following commands:
escript -fns "ip for env1":port
findsub nameservice
showpart
What you should see is everything currently registered under the name
service. It will have the name and any "locations" (IP and port) that it
is
registered as listening on. I would look for the nodemgr and see where it
has advertised itself. I would then look for any services you expect to
be
registered there and also verify where the have advertised themselves. If
there are multiple locations listed for any one service, the client will
use
the first one in the list.
Do the same for env 2.
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Monday, June 22, 1998 9:57 AM
To: 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same machine
I am giving the actual IP address. and not the host name. That is why I
don't understand what is going on.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Monday, June 22, 1998 10:53 AM
To: Venkat Kodumudi; 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
Hello Venkat,
I probably should have mentioned this before. Your are correct. Forteis
doing a host lookup if you are providing a name for examplemachine1:5000.
You can bypass the host lookup by using the actual ip dot addressinstead
for example 255.255.255.255:5000. This way you are taking the name
service
out od the picture and Forte will use the address provided.
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Monday, June 22, 1998 9:27 AM
To: 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same machine
My requirement is that my second card serves as best case performance
testing piece. This eliminates the network completely. We went one step
ahead and created a new enviromnent for the second card. Whatever I do,
the
nodemgr is returning back the IP address of the first card, even thoughmy
FORTE_NS_ADDRESS does not have the first card in the picture any where.
I think Forte is doing a host look up and returning the first IP address
it
finds, as opposed to returning the IP address specified in theenvironment
variable FORTE_NS_ADDRESS. Is there a way to trick it?
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Thursday, June 18, 1998 9:54 AM
To: Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
OK, you ran into one of the issues. That is, if both addresses areknown
to
the client that is trying to contact the partition it will always usethe
first address in FORTE_LOCATIONS. This is because FORTE_LOCATIONS was
designed more as a failover mechanism. So it will always try the
first
address in the list and if it succeeds, there is no reason to move onto
the
second.
Now, the second issue is that there is currently a problem with theclient
failover to the secondary address in FORTE_LOCATIONS. If the firstentry
fails it is supposed to retry on the second entry. Instead, it
retries
the
first entry again. I know that Forte knows about this but I do nothave
a
bug number on it.
With that said, lets look at a possible solution for you. If the real
objective here is to have a back up network card available for fail
over
on
the same machine, or use one card to advertise outside your firewalland
one
to use inside, then you will have to contact Forte to determine whenthe
failover problem will be fixed. But, if the objective is to loadbalance
across the network cards you could have the environment manager listenon
both ports and then alternate your server partitions across both
cards.
For
example:
set FORTE_NS_ADDRESS=card1:5000;card2:5000 and then start up the
environment
manager
set FORTE_LOCATIONS=card1:0 (the 0 in the port causes the OS to pick a
port)
and start partition one
set FORTE_LOCATIONS=card2:0 and start partition two
and so on....
In this scenario the environment manager will be listening on bothcards
but
each server will be listening on only one of the two cards. So if a
request
comes in for partition1 it will go through card one and if it is for
partition two it will go through card two. You could assign your
partitions
to cards based on expected load.
Well, I am done. I hope this helps!
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Thursday, June 18, 1998 8:06 AM
To: 'Sean Brown'; 'John Jamison'
Cc: [email protected]; Jose Suriol
Subject: RE: Is there a way to have 2 network cards on the samemachine
Sean,
Thanks for your reply. I tried the approach. I was not very specificin
my
question. I do need the ability for server applications to listen and
server
on both the network cards.
I was succesfully able to make the nodemgr listen on both the cardsand
actually serve requests coming in from both the cards. But, followingyour
advise, I took a cautious step with FORTE_LOCATIONS. Here is what I
noticed.
I have an application that has 6 partitions in total. I used
FORTE_LOCATION
to make it listen on 1. Both the cards. 2. Swapped the IP addresses
for
both
cards for this application. 3. One card that I want it to listen on. I
tried
all approaches by exporting the locations variable for just this
application. The nodemgr recieves a request from this pc connected onthe
second card to talk to one of the partitions. The node mgr responds
with
a
proxy - with the ip address and socket number of the first card. The
FORTE_NS_ADDRESS variable looks like this:
IP1:5002;IP2:5002.
Is it possible atall to resolve my problem, without having a seperate
environment?
Thanks
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Wednesday, June 17, 1998 10:42 AM
To: 'John Jamison'; Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the
same
machine
Venkat,
Actually, it is possible for Forte to listen on more than one IP andport
combination. The first reply to your message was correct. If you
set
the
FORTE_NS_ADDRESS to contain multiple entries before starting the
name
service, it will advertise on both. For Forte servers you use the
FORTE_LOCATIONS env variable to get it to advertise on multipleip:port
combinations.
We were doing something very similar with another customer I was at
to
get
around a firewall. I will warn you that there are some issues with
FORTE_LOCATIONS that may keep that portion from working. However,
from
reading your note, it appears that all you need is for the nameservice
to
advertise and listen on multiple ports and that works fine. I justtested
it again for sanity sake and it worked. I ran my test on NT using
Forte
3G2.
Sean
-----Original Message-----
From: [email protected]
[<a href="mailto:[email protected]">mailto:[email protected]]On</a> Behalf Of John Jamison
Sent: Tuesday, June 16, 1998 4:51 PM
To: Venkat Kodumudi
Cc: [email protected]
Subject: Re: Is there a way to have 2 network cards on the samemachine
Venkat,
Technically yes this is possible, though not in Forte. A nameserver
can
only listen on one port.
To implement this scheme you will have to write a proxy service (insome
language
including perhaps forte) which listens on the well-known port on the
second card, reads requests, then forwards them to the realnameservice
(wkp on the first card), and forwards replies back. This is not
trivial, but some firewall toolkit vendors supply stub code to write
application specific proxies.
-J
Venkat Kodumudi wrote:
Folks,
Here is what we would like to do:
We want to have 2 network cards on a unix box - which means I have
2
ip
addresses, and the connection between the two is the unix box and
only
the
unix box. I have a pc connected to the 2nd network card and I want
it
to
connect to the nameserver that is listening on a well known port
on
the
first network card. We don't want to turn IP forwarding between
the
two
cards. We want Forte to address both cards to talk to clients, in
one
environment.
Can this be done? If so how?
Thanks in advance.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive<URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>
>>>>
John Jamison [email protected]
Vice President and Chief Technology Officer
Sage IT Partners, Inc.
Voice: 415 392-7243 x 306
Fax: 415 391-3899
Internet Enabled Business Change
<a href=
"http://www.sageit.com">http://www.sageit.com</a>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>

Hello Venkat,
I probably should have mentioned this before. Your are correct. Forte is
doing a host lookup if you are providing a name for example machine1:5000.
You can bypass the host lookup by using the actual ip dot address instead
for example 255.255.255.255:5000. This way you are taking the name service
out od the picture and Forte will use the address provided.
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Monday, June 22, 1998 9:27 AM
To: 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same machine
My requirement is that my second card serves as best case performance
testing piece. This eliminates the network completely. We went one step
ahead and created a new enviromnent for the second card. Whatever I do, the
nodemgr is returning back the IP address of the first card, even though my
FORTE_NS_ADDRESS does not have the first card in the picture any where.
I think Forte is doing a host look up and returning the first IP address it
finds, as opposed to returning the IP address specified in the environment
variable FORTE_NS_ADDRESS. Is there a way to trick it?
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Thursday, June 18, 1998 9:54 AM
To: Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
OK, you ran into one of the issues. That is, if both addresses are known
to
the client that is trying to contact the partition it will always use the
first address in FORTE_LOCATIONS. This is because FORTE_LOCATIONS was
designed more as a failover mechanism. So it will always try the first
address in the list and if it succeeds, there is no reason to move on to
the
second.
Now, the second issue is that there is currently a problem with the client
failover to the secondary address in FORTE_LOCATIONS. If the first entry
fails it is supposed to retry on the second entry. Instead, it retries
the
first entry again. I know that Forte knows about this but I do not have a
bug number on it.
With that said, lets look at a possible solution for you. If the real
objective here is to have a back up network card available for fail over
on
the same machine, or use one card to advertise outside your firewall and
one
to use inside, then you will have to contact Forte to determine when the
failover problem will be fixed. But, if the objective is to load balance
across the network cards you could have the environment manager listen on
both ports and then alternate your server partitions across both cards.
For
example:
set FORTE_NS_ADDRESS=card1:5000;card2:5000 and then start up the
environment
manager
set FORTE_LOCATIONS=card1:0 (the 0 in the port causes the OS to pick a
port)
and start partition one
set FORTE_LOCATIONS=card2:0 and start partition two
and so on....
In this scenario the environment manager will be listening on both cards
but
each server will be listening on only one of the two cards. So if a
request
comes in for partition1 it will go through card one and if it is for
partition two it will go through card two. You could assign your
partitions
to cards based on expected load.
Well, I am done. I hope this helps!
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Thursday, June 18, 1998 8:06 AM
To: 'Sean Brown'; 'John Jamison'
Cc: [email protected]; Jose Suriol
Subject: RE: Is there a way to have 2 network cards on the same machine
Sean,
Thanks for your reply. I tried the approach. I was not very specific in
my
question. I do need the ability for server applications to listen and
server
on both the network cards.
I was succesfully able to make the nodemgr listen on both the cards and
actually serve requests coming in from both the cards. But, following your
advise, I took a cautious step with FORTE_LOCATIONS. Here is what I
noticed.
I have an application that has 6 partitions in total. I used
FORTE_LOCATION
to make it listen on 1. Both the cards. 2. Swapped the IP addresses for
both
cards for this application. 3. One card that I want it to listen on. I
tried
all approaches by exporting the locations variable for just this
application. The nodemgr recieves a request from this pc connected on the
second card to talk to one of the partitions. The node mgr responds with a
proxy - with the ip address and socket number of the first card. The
FORTE_NS_ADDRESS variable looks like this:
IP1:5002;IP2:5002.
Is it possible atall to resolve my problem, without having a seperate
environment?
Thanks
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Wednesday, June 17, 1998 10:42 AM
To: 'John Jamison'; Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
Venkat,
Actually, it is possible for Forte to listen on more than one IP andport
combination. The first reply to your message was correct. If you setthe
FORTE_NS_ADDRESS to contain multiple entries before starting the name
service, it will advertise on both. For Forte servers you use the
FORTE_LOCATIONS env variable to get it to advertise on multiple ip:port
combinations.
We were doing something very similar with another customer I was at toget
around a firewall. I will warn you that there are some issues with
FORTE_LOCATIONS that may keep that portion from working. However, from
reading your note, it appears that all you need is for the name serviceto
advertise and listen on multiple ports and that works fine. I justtested
it again for sanity sake and it worked. I ran my test on NT using Forte
3G2.
Sean
-----Original Message-----
From: [email protected]
[<a href="mailto:[email protected]">mailto:[email protected]]On</a> Behalf Of John Jamison
Sent: Tuesday, June 16, 1998 4:51 PM
To: Venkat Kodumudi
Cc: [email protected]
Subject: Re: Is there a way to have 2 network cards on the same machine
Venkat,
Technically yes this is possible, though not in Forte. A name server
can
only listen on one port.
To implement this scheme you will have to write a proxy service (in some
language
including perhaps forte) which listens on the well-known port on the
second card, reads requests, then forwards them to the real nameservice
(wkp on the first card), and forwards replies back. This is not
trivial, but some firewall toolkit vendors supply stub code to write
application specific proxies.
-J
Venkat Kodumudi wrote:
Folks,
Here is what we would like to do:
We want to have 2 network cards on a unix box - which means I have 2ip
addresses, and the connection between the two is the unix box and onlythe
unix box. I have a pc connected to the 2nd network card and I want it
to
connect to the nameserver that is listening on a well known port onthe
first network card. We don't want to turn IP forwarding between thetwo
cards. We want Forte to address both cards to talk to clients, in one
environment.
Can this be done? If so how?
Thanks in advance.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive<URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>
>>
John Jamison [email protected]
Vice President and Chief Technology Officer
Sage IT Partners, Inc.
Voice: 415 392-7243 x 306
Fax: 415 391-3899
Internet Enabled Business Change
<a href="http://www.sageit.com">http://www.sageit.com</a>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>

How to use two different network cards on RT?

Hi everyone... I'm currently working on a project where I have to deal with the issue mentioned in the thread's topic: I have a PC with RT LabVIEW that has to be able to establish network connections using two different network cards. One will be used to connect via TCP/IP with a host computer that will show the data transmitted through shared variables; the other will communicate with another PC through Modbus protocol. The key is that each communication is done through a separate network card.
So far I haven't been able to figure out how to configure both things to happen. Does anyone know how to do this? Any tips will help.
For the RT communication I'm using a standard RT project, with the RT PC being given one of the IPs, and for the Modbus part, I created an I/O server with a master and a slave. Separately everything works fine, but when I get them together it simply won't work.
Thanks for your help!
Solved!
Go to Solution.

Sorry it took me so long to answer, I've been busy lately....I've found a solution to the problem I mentioned, and just in case anyone has similar problems in the future, I'll shortly describe what happened.
As Caseyw suggested, it was necessary to enable both network cards through the Measurement and Automation Explorer. The cause of the connections malfunction was actually that I wasn't using the "right" protocol for the Modbus communication, which ran on the secondary adapter. The solution was to use the URL protocol with the correct path on the field, addressing the right IP address. To avoid making this post a mixture of topics, I won't elaborate futher, but I got the gist of it, so if anyone is having similar problems whether it is working with several network cards or with Modbus communication protocols, feel free to contact me, I'll be glad to help.
Thanks

Is there a way to have 2 network cards on the samemachine

Folks,
Here is what we would like to do:
We want to have 2 network cards on a unix box - which means I have 2 ip
addresses, and the connection between the two is the unix box and only the
unix box. I have a pc connected to the 2nd network card and I want it to
connect to the nameserver that is listening on a well known port on the
first network card. We don't want to turn IP forwarding between the two
cards. We want Forte to address both cards to talk to clients, in one
environment.
Can this be done? If so how?
Thanks in advance.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

Hmmmm? That is a little odd! Let me rehash what I think you are saying.
You now have two environments each with their own name service with
FORTE_NS_ADDRESS set to a different IP:Port combination. For example you
are doing the steps:
FORTE_NS_ADDRESS=255.255.255.1:5000
start the nodemgr for env 1
FORTE_NS_ADDRESS=255.255.255.2:5000
start the nodemgr for env 2
Now when you start a client you are always getting the address for env 1
back from the nodemgr. I assume you actually mean the name service? Or, do
you mean you are always connecting to the nodemgr & name service for env 1?
If the first scenario is the case and you are connecting to the nodemgr for
env 2 but getting back IP's for services listening on the card for env 1 I
would ask you what you are setting the FORTE_LOCATIONS value to before you
start each service. If you are not setting it or are using the host name it
will register using the IP for the primary network card associated with the
machine name and I am again assuming that this is env 1. You need to set
the FORTE_LOCATIONS variable to 255.255.255.2:0 (based on the steps above)
before starting your services.
If the second scenario is the case I would have you check what the
FORTE_NS_ADDRESS is set to before you start up the client. Once again it
must be the IP:Port combination not host:port combination if you want to get
anything other than the primary card.
I would also suggest that you do the following. After everything is up and
running execute the following commands:
escript -fns "ip for env1":port
findsub nameservice
showpart
What you should see is everything currently registered under the name
service. It will have the name and any "locations" (IP and port) that it is
registered as listening on. I would look for the nodemgr and see where it
has advertised itself. I would then look for any services you expect to be
registered there and also verify where the have advertised themselves. If
there are multiple locations listed for any one service, the client will use
the first one in the list.
Do the same for env 2.
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Monday, June 22, 1998 9:57 AM
To: 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same machine
I am giving the actual IP address. and not the host name. That is why I
don't understand what is going on.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Monday, June 22, 1998 10:53 AM
To: Venkat Kodumudi; 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
Hello Venkat,
I probably should have mentioned this before. Your are correct. Forte is
doing a host lookup if you are providing a name for example machine1:5000.
You can bypass the host lookup by using the actual ip dot address instead
for example 255.255.255.255:5000. This way you are taking the name
service
out od the picture and Forte will use the address provided.
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Monday, June 22, 1998 9:27 AM
To: 'Sean Brown'
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same machine
My requirement is that my second card serves as best case performance
testing piece. This eliminates the network completely. We went one step
ahead and created a new enviromnent for the second card. Whatever I do,
the
nodemgr is returning back the IP address of the first card, even though my
FORTE_NS_ADDRESS does not have the first card in the picture any where.
I think Forte is doing a host look up and returning the first IP address
it
finds, as opposed to returning the IP address specified in the environment
variable FORTE_NS_ADDRESS. Is there a way to trick it?
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Thursday, June 18, 1998 9:54 AM
To: Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
OK, you ran into one of the issues. That is, if both addresses areknown
to
the client that is trying to contact the partition it will always usethe
first address in FORTE_LOCATIONS. This is because FORTE_LOCATIONS was
designed more as a failover mechanism. So it will always try the first
address in the list and if it succeeds, there is no reason to move on to
the
second.
Now, the second issue is that there is currently a problem with theclient
failover to the secondary address in FORTE_LOCATIONS. If the firstentry
fails it is supposed to retry on the second entry. Instead, it retries
the
first entry again. I know that Forte knows about this but I do not havea
bug number on it.
With that said, lets look at a possible solution for you. If the real
objective here is to have a back up network card available for fail over
on
the same machine, or use one card to advertise outside your firewall and
one
to use inside, then you will have to contact Forte to determine when the
failover problem will be fixed. But, if the objective is to loadbalance
across the network cards you could have the environment manager listenon
both ports and then alternate your server partitions across both cards.
For
example:
set FORTE_NS_ADDRESS=card1:5000;card2:5000 and then start up the
environment
manager
set FORTE_LOCATIONS=card1:0 (the 0 in the port causes the OS to pick a
port)
and start partition one
set FORTE_LOCATIONS=card2:0 and start partition two
and so on....
In this scenario the environment manager will be listening on both cards
but
each server will be listening on only one of the two cards. So if a
request
comes in for partition1 it will go through card one and if it is for
partition two it will go through card two. You could assign your
partitions
to cards based on expected load.
Well, I am done. I hope this helps!
Sean
-----Original Message-----
From: Venkat Kodumudi [mailto:[email protected]]
Sent: Thursday, June 18, 1998 8:06 AM
To: 'Sean Brown'; 'John Jamison'
Cc: [email protected]; Jose Suriol
Subject: RE: Is there a way to have 2 network cards on the same machine
Sean,
Thanks for your reply. I tried the approach. I was not very specific in
my
question. I do need the ability for server applications to listen and
server
on both the network cards.
I was succesfully able to make the nodemgr listen on both the cards and
actually serve requests coming in from both the cards. But, followingyour
advise, I took a cautious step with FORTE_LOCATIONS. Here is what I
noticed.
I have an application that has 6 partitions in total. I used
FORTE_LOCATION
to make it listen on 1. Both the cards. 2. Swapped the IP addresses for
both
cards for this application. 3. One card that I want it to listen on. I
tried
all approaches by exporting the locations variable for just this
application. The nodemgr recieves a request from this pc connected onthe
second card to talk to one of the partitions. The node mgr responds witha
proxy - with the ip address and socket number of the first card. The
FORTE_NS_ADDRESS variable looks like this:
IP1:5002;IP2:5002.
Is it possible atall to resolve my problem, without having a seperate
environment?
Thanks
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
-----Original Message-----
From: Sean Brown [SMTP:[email protected]]
Sent: Wednesday, June 17, 1998 10:42 AM
To: 'John Jamison'; Venkat Kodumudi
Cc: [email protected]
Subject: RE: Is there a way to have 2 network cards on the same
machine
Venkat,
Actually, it is possible for Forte to listen on more than one IP andport
combination. The first reply to your message was correct. If you setthe
FORTE_NS_ADDRESS to contain multiple entries before starting the name
service, it will advertise on both. For Forte servers you use the
FORTE_LOCATIONS env variable to get it to advertise on multiple
ip:port
combinations.
We were doing something very similar with another customer I was at toget
around a firewall. I will warn you that there are some issues with
FORTE_LOCATIONS that may keep that portion from working. However,
from
reading your note, it appears that all you need is for the nameservice
to
advertise and listen on multiple ports and that works fine. I justtested
it again for sanity sake and it worked. I ran my test on NT using
Forte
3G2.
Sean
-----Original Message-----
From: [email protected]
[<a href="mailto:[email protected]">mailto:[email protected]]On</a> Behalf Of John Jamison
Sent: Tuesday, June 16, 1998 4:51 PM
To: Venkat Kodumudi
Cc: [email protected]
Subject: Re: Is there a way to have 2 network cards on the samemachine
Venkat,
Technically yes this is possible, though not in Forte. A nameserver
can
only listen on one port.
To implement this scheme you will have to write a proxy service (insome
language
including perhaps forte) which listens on the well-known port on the
second card, reads requests, then forwards them to the realnameservice
(wkp on the first card), and forwards replies back. This is not
trivial, but some firewall toolkit vendors supply stub code to write
application specific proxies.
-J
Venkat Kodumudi wrote:
Folks,
Here is what we would like to do:
We want to have 2 network cards on a unix box - which means I have 2
ip
addresses, and the connection between the two is the unix box and
only
the
unix box. I have a pc connected to the 2nd network card and I want
it
to
connect to the nameserver that is listening on a well known port onthe
first network card. We don't want to turn IP forwarding between thetwo
cards. We want Forte to address both cards to talk to clients, in
one
environment.
Can this be done? If so how?
Thanks in advance.
Venkat Kodumudi
Price Waterhouse LLP
Internet: [email protected]
Internet2: [email protected]
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive<URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>
>>>
John Jamison [email protected]
Vice President and Chief Technology Officer
Sage IT Partners, Inc.
Voice: 415 392-7243 x 306
Fax: 415 391-3899
Internet Enabled Business Change
<a href=
"http://www.sageit.com">http://www.sageit.com</a>
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:<a href=
"http://pinehurst.sageit.com/listarchive/">http://pinehurst.sageit.com/listarchive/</a>>

Swipe Card Integration

Hi Experts,
One of my client requires swipe card integration with SAP..... which is new to me........
I need some basic inputs on this........
Thanks
Anto

hi,
       I did this type program using one fm 'HR_MAINTAIN_MASTERDATA' which will upload the 2011 infotype field SATZA, in which events are p10, p20, p15 break-in and p25 break-out. You have to pass pernr( personnel number) , begda(begin date), endda(end date) , opern(operation to insert'INS') , return message(bapireturn type) and pprop table in which you have to pass field name , value and infotype for each mandatory field.
        Then it will get upload to the infotype.
        I think this is simple than writing BDC coding. It doesn't require any recording also.
thanks & regards,
     sekhar.

Different afp shares for different network cards (NIC)

Hi,
I have a machine sharing via two connections on two separate physical connectors.
One is restricted to LAN, the other is allowed to use the internet connection.
How do I set up shares only available on the LAN connection?
Thanks

Sorry it took me so long to answer, I've been busy lately....I've found a solution to the problem I mentioned, and just in case anyone has similar problems in the future, I'll shortly describe what happened.
As Caseyw suggested, it was necessary to enable both network cards through the Measurement and Automation Explorer. The cause of the connections malfunction was actually that I wasn't using the "right" protocol for the Modbus communication, which ran on the secondary adapter. The solution was to use the URL protocol with the correct path on the field, addressing the right IP address. To avoid making this post a mixture of topics, I won't elaborate futher, but I got the gist of it, so if anyone is having similar problems whether it is working with several network cards or with Modbus communication protocols, feel free to contact me, I'll be glad to help.
Thanks

Wireless Network Card

When i bought my K8N NEO2 Plat. it came with the wireless network card bundled with it, ever since i have started using it i have had nothing but problems with it, it keeps dropping the connection every 10 mins or so and also does it when using or exiting a program which makes online gaming almost impossible, does anyone know what could be wrong.
BTW i am connecting to a another computer, i also have a laptop that uses another wireless access point and that never drops the connection

I have the same problem.
What I have realized is that moveing the antenna just a little bit helps a lot on the signal strength. I had my antenna on of my cabinet with LOW to VERY LOW signal. Moved the antenna to the floor, got GOOD to VERY GOOD signal.
However I have to say that the Wireless card that is included with the NEO 2 is a 2nd hand solution. I have tried with other PCI based Wireless cards. No problem with either the driver or the singal strength. So the conclusion must be that if you can afford it, buy a new Wireless card.
Infact both the onbaord audio and the Wireless solution on the NEO 2 is really of rahter poor quality. In my opinion MSI should never have included em in the package.

PCI USB2 Controller card conflicts with network card

I've installed a PCI USB2 controller card since my motherboard (IWill K266-R) only has support for USB1. However, the card seems to conflict with one of my network cards, because traffic on the internet-connected NIC is very slow, and often drops completely. Traffic to and from the other (local) NIC seems to work fine, though.
I have tried moving around all three cards in different PCI slots, I think I've tested almost every possible combination by now. I've also tried disabling as much as possible in BIOS, such as onboard sound, serial and parallel ports etc. I've tried lowering the FSB.
For now, I've removed the controller card, and is using the USB1 ports on the motherboard instead. This is very frustrating, though.
Does anyone have any suggestion on what I can try next? I've browsed forums, both this and others, but I haven't found any more hints on what to try. Could there be some setting in Arch that could affect these sorts of things?

"I guess the ATA100 card will work fine correct?"
If you mean large drive support, it may provide that or may require a firmware update to do so. You should check the manufacturer's web site for specifics. All ATA-133 cards do provide 48-bit LBA for large drive support. I'd return the Ultra ATA-66 card to the eBay seller, although many refuse to pay for return shipping, even when the mistake is their own, either through ignorance or deliberate misrepresentation. In cases such as this, it's sometimes more cost-effective to swallow the loss and keep the incorrect part.
"Will adding a jumper apply for a ATA100 card as well? I'll need a blue and gray ribbon correct?"
If you use an 80-conductor ribbon cable with color-keyed connectors, set the drive configuration jumper to CS and connect the drives to the cable as you wish (in terms of physical placement in the computer). If the ribbon cable doesn't have color-keyed connectors, set the jumper for the device connected to the end connector as Master and the drive (if any) connected to the middle connector as Slave.

Network card integrated with motherboard

Similar Messages

Maybe you are looking for