Network connection not working

I did an FTP install off the boot CD, everything went fine there. After I reboot and startup Arch linux, I get a FAILED message when it tries to start the network. I have my eth0 set to "dhcp" and INTERFACES set to (lo eth0) in rc.conf. I've used other distos before and my card uses the 8139too driver, NOT the 8139cp one. An lsmod shows that it is in fact loading the 8139cp driver. How do I get it to load the 8139too and not the 8139too driver?

you can edit /etc/rc.conf like this:
Modules = (uhci-hcd ehci-hcd 8139too)
and take away "hotplug" from the daemons array,
there is also a "blacklist"  for hotplug somewhere but I don't know where it is,

Similar Messages

  • Apple tv network connection not working after 4.2.2 upgrade

    I think the 4.2.2 upgrade has broken something.   My Apple tv wifi connection has been working fine.  Stopped working after the upgrade. 
    Laptop and mac mini working fine through the wap.
    My wap is a time capsule
    I've got good signal strength and a valid ip address.  Still no connectivity to the internet or to my itunes library from the apple tv
    -Tim

    Unplug and restart.
    If no joy reset settings in Settings menus.
    If still no joy and you have a micro USB cable do a proper reset via iTunes.
    AC

  • Wrt610n wireless network does not work after firmeware upgrade

    Hi
    I just updated my Wrt610n hardware version 1 to the newest firmware, it did finish with sucess, I did factory reset reboot and reconfig. But the wireless network does not work , cant connect computers to it. Did downgrade the firmware to the same it was and restore my settings but still wireless does not work. But router works fine with lan.  Any suggestions? maybe the firmware tosted the router?
    Regards
    Stefan

    Update -
    After last reset and reupgrade with the newest firmware for hardware version 1 I could config the router and connect 2 computers with wireless - but only for about 15 mín - then they lost connection and could not reconnect.
    I did then get the newest update for hardeware version 2 - just to try and upgraded with that and got success, and now I have reset the router again and config it and those 2 computers are connected and have been for 1 hour now. So seems to be working - is it okay to have the firmware for hardware version 2 on my version 1 router?
    Any thought what is going on - could it be that the other firmware had not loaded compleytle or?

  • I have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

    i have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar also..,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

    I am seeing if I can get another battery even though I do not believe that is the issue.  It keeps giving me vdd_under which I believe is under voltage, maybe it is just a faulty battery?  It charges up like normal and functions normal (when plugged in, or above 90%) but it gives under voltage warnings and shuts down when in heavy use (using camera or going back and forth to imessage).  When just sitting idle it doesn't seem to turn off until that 55-60% mark.  It may just be a faulty battery because I feel I installed all of the other cables correctly when replacing the screen, and I don't think those connections should affect the battery anyway except for maybe the logic board cable (the 2nd cable to be unplugged after the battery cable) I guess I could clean that out as well with isopropyl just in case.
    Any other suggestions would be helpful... and I will get back to you if a new battery helps.  Thanks!

  • Primary network does not work, guest network does work

    I updated the firmware on the Time Capsule, after which we had a power outage. When the Time Capsule came back up, after a bunch of fiddling around we discovered that although the primary network cannot connect the Internet through our phone system router, the guest network works fine. The primary network does not work with the guest network turned off. Resetting the Time Capsule had no effect.

    After an entire day of messing around, we went into Airport Utility, selected Internet, selected DHCP, and changed DHCP Beginning Address to match the one showing on the guest network (172.16). Now the primary network can see the Internet.

  • Network does not work or the network signal attenuates rapidly

    Network does not work or the network signal attenuates rapidly

    Hello shishir_teamo,
    If you are having issues with Wi-Fi on you iPhone 4S, check the following article that will help troubleshoot the issue.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

    So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

    Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Mail box frozen. Cannot send or receive. Network connections all working. Help?

    Mail box frozen. Cannot send or receive. Network connections all working. Help?

    Ernie,
    Thanx a lot. It seems my domain name ran out, and I didn't get a 'renew soon' email cuz the auxiliary address they had had changed over the years.
    That said, even tho I renewed I'm still not getting service. Pair mentioned it'll take up to an entire day to get reconnected; so I'll wait until tonight.
    Thanx for chiming in.

  • HI my network connections is working fine but it doesnt allow me to update software or access apple store. Any suggestions?

    HI my network connections is working fine but it doesnt allow me to update software or access apple store. Any suggestions?

    Then it simply was NOT Brand New. Doesn't matter what the box looked like when you got it or if you went through the setup pages when you first turned it on. If it is registered to some other Apple ID then someone else had originally registered it and locked it to there ID.
    Type in the serial number of the system into this page.
    https://selfsolve.apple.com/agreementWarrantyDynamic.do
    And see when it was originally registered.
    Then send it back to Amazon as Used.
    LordRavenWolfe wrote:
    So I bought a brand new macbook from Amazon, and it came factory sealed (Not my first time buying a macbook, last one I bought was from Apple directly) but after I got this, I put in my apple I.D. and it told me there were updates available. I told it to go ahead and update, and it updated about half of the list, but the essential stuff (pages, notes, etc) it says "This software was installed using another Apple I.D. Please logon with that I.D. to install the software."  I'm a bit baffled by this as it is a brand new mac and so I don't know why anyone else's I.D. would be logged into this mac.  I'm not really worried about it though, as I don't really need to update my pages, etc, as I like what I have, but I'd love for this stupid "updates availble" popup to stop popping up every freaking day!!!
    Anyone have any suggestions on finding out how to either gain access to update, or get rid of that "other" i.d. that is somehow associated with my brand new macbook?
    I'm running OSX 10.9 if that is of any consequence.

  • My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1and it was not jillbreak or hacked to unlock. I need help, what can I do?

    My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1
    my phone was not jillbreak or hacked to unlock. i need help, what can I do?

    Did you do the Reset Network Settings as I described above?
    There is no way to go back. You can try reseating your nanoSIM or replacing it. Or call your cell provider and have them check the provisioning on your phone.
    Or Restore your iPhone from your backup in iTunes.

  • My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1 i need help, what can I do?

    My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !!
    It was working fine on ios 8.1.1 i need help, what can I do?

    I have this problem too - and it is on a BRAND new iPhone 6 - I have definitively tracked the issue to the moment I upgraded to iOS 8.1.2 - and am beyond frustrated. No fix to tell you about, sorry…but you can read my post here if you are into the whole "misery loves company" thing: iOS 8.1.2 Cellular data problem (Definitive - maybe)

  • My Iphone 4 network is not working in Malaysia

    My Iphone 4 network is not working in Malaysia as I offered for 2 month period by behalf of my company and when buy a sim card in Malaysia then I only realise there were no network and I bring to a shop and they upgraded my Iphone and it stuck on the activation part which require a network. Any Solution ?

    iphone 4 and 4S have two microphones...bottom n top...sometimes top microphone is covered by the case or sheet as in my case..and when i just put off the case it was working fine.....i just got problem today and today it is solved again.....may be its ur case or may be ur case is a genuine hardware software problem...just for info

  • Wireless network connection not showing up in network connections

    Hi, Experts,
    I recently re-image my Toshiba laptop (using window xp installation disk) due to I deleted few system files accidentally and can not boot the system up.
    Before I re-image, I have no problem to connect Fios internet. After the re-image, the wireless network connection not showing up in network connections, so I cannot set up my Fios internet. 
    How to set up the  wireless network connection that it will show up in network connections?  Thank you very much for your help. 

    Issue Resolved.  I did not turn on the wireless switch.

  • After Hard Reset My Social Network is not working....

    Due to Some problem I did Hard Reset to my C7 but now My Social network is not working.
    I had reinstall the nokia software but still its not working properly.
    In the Social network all the graphics are coming like picture with a cross.

    Something is wrong because a hard reset will never leave the TC with green LED.
    What version TC.. what firmware??
    What OS on the computer?

  • My network is not working i am in ghana and i use MTN  network but it is not working why is it like that

    my network is not working i am in ghana and i use MTN  network but it is not working why is it like that... pls get back to me now

    It sounds as if you need to call your mobile carrier.

Maybe you are looking for

  • Buttons not working on updateable SQL report

    Hello I have created an updateable SQL report using the wizard but for some reason none of the buttons (Add Row, Delete, Submit) are working. When I click on 'Submit', the changes aren't saved. When I click on Add Row I get 'Page cannot be displayed

  • Calling a report from Form 6i

    Hi, I want to call a report from Form 6i at run time. And I write the following code in When Buttton Press trigger . when I press the button it will gives no response. declare      x report_object;      y varchar2(100); begin      x:=find_report_obje

  • HT1807 can i use local sims in my i pad to reduce costs i'm going to singapore and oz

    can i use a local sim in my ipad 2? to keep costs down, i'm travelling to singapore and oz?

  • Files without extensions read as UNIX exe files

    I have an iMac connecting to my MacBook Pro that has several external drives attached by firewire. On those external drives the iMac sees any file without an extension as exe files. In particular, font files are seen this way. Can I add extension to

  • Forcing a Report to Fail

    Is it possible to force a report to fail if the query or stored procedure returns 0 rows with using Report Builder 3.0?