Network Control System - one device for whole world?

Hi all,
we have Network Control System located in South Africa. Would it be possible to effectively use it also for devices in e.g. LATAM, Europe or Australia? Round Trip Time for these locations can be up to 500 ms, ocassionaly, during busy hours, this can go up to 800 ms.
Thanks,
Gorazd

Hi Scott,
Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
Can you pls check this.
Regards

Similar Messages

  • Cisco Prime Infrastructure 1.2 with Cisco Prime Network Control System Hardware Appliance

    Hi Team,
    I have  following BOM
    Cisco Prime Infrastructure
    R-PI-1.2-K9
    Cisco Prime Infrastructure 1.2
    1
    R-PI-1.1-500-K9
    Prime Infrastructure 1.2 Software - 500 Device Base Lic
    1
    L-PILMS42-500
    Prime Infrastructure LMS 4.2 - 500 Device Base Lic
    1
    L-PINCS12-500
    Prime Infrastructure NCS 1.2 - 500 Device Base Lic
    1
    PRIME-NCS-APL-K9
    Cisco Prime Network Control System Hardware Appliance
    1
    PI-APL-IMAGE-1.2
    Cisco Prime Infrastructure 1.2 Appliance Software
    1
    Pls let me know if we have both NCS and LMS preinstalled with Cisco Prime Infrastructure 1.2 Appliance Software orwe need seperate appliance or server for LMS 4.2. 
    Regards

    Hi Scott,
    Thanks for the response but I got to know that LMS and NCS are combined in single ISO image from PI 1.2 and can be installed on the same physical NCS appliance.
    Can you pls check this.
    Regards

  • Cisco Network Control System software

    As far as I know, the NCS is an appliance. But today some people told me that he has a copy of Cisco's Network Control System software. I am confused. If what he said is true, can I install the software on the Windows platforms like Win2003 or Win2008?
    Thanks in advance.
    Robert

    Hi Robert,
    Here we go
    Product Specifications for Cisco Prime NCS
    Item
    Specification
    VMware ESX and ESXi Versions (Virtual Appliance on a Customer-Supplied Server)
    If deploying Cisco Prime NCS as a virtual appliance, on a customer-supplied server, one of the following versions of VMware ESX or ESXi may be used:
    • VMWare ESX or VMWare ESXi version 4.1
    Minimum Server Requirements for Deploying Virtual Appliances
    Cisco Prime NCS High-End Virtual Appliance:
    • 15,000 lightweight access points; 5000 standalone access points; 1200 wireless LAN controllers and 5000 switches
    • Minimum RAM: 16GB
    • Minimum Hard disk space allocation: 400GB
    • Processors: 8, at 2.93GHz or better
    Cisco Prime NCS Standard Virtual Appliance:
    • 7500 lightweight access points; 2500 standalone access points; 600 wireless LAN controllers and 2500 switches
    • Minimum RAM: 12GB
    • Minimum Hard disk space allocation: 300GB
    • Processors: 4, at 2.93GHz or better
    Cisco Prime NCS Low-End Virtual Appliance:
    • 3000 lightweight access points; 1000 standalone access points; 240 wireless LAN controllers and 1000 switches
    • Minimum RAM: 8GB
    • Minimum Hard disk space allocation: 200GB
    • Processors: 2, at 2.93GHz or better
    Deploying Cisco Prime NCS Virtual Appliance on CiscoWorks Wireless LAN Solution Engine (WLSE) models 1130-19 or 1133
    • Cisco Prime NCS is not supported on the Cisco WLSE hardware
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps11682/ps11686/ps11688/data_sheet_c78-650051.html
    Cheers!
    Rob

  • How many iPads can be controlled by one device using keynote remote

    How many iPads can be controlled by one device using keynote remote?

    ask your question in the iWork for iOS  discussion
    iWork for iOS

  • Prime network control system appliance (NCS)

    Hi,
    i have a new cisco prime network control system appliance (NCS)
    I completed the initial installation however post installation it performed a reboot and is now stuck at Init Level 3.
    I have restarted the machine several time but the same result.

    Umm a new appliance should have had the application pre-installed. Were you upgrading?
    In either case, you'll probably need to open a TAC case. Even without Smartnet you should have at least 90-day warranty support

  • Apple ID for business, one device for multiple users

    My workplace has purchased 3 iPads for staff use on 3 departments, each department has multiple employees each will require use of the device.
    We'd like to avoid one staff member signing in with their personal Apple ID as the device will then be passed to a different team member and therefore to access apps would need the password from the Apple ID user.
    We'd like control over what ID is used, what apps are installed and how the device is used.
    Is there a business option for corporate Apple ID? If not, what is the best solution for this scenario?

    3 iPads for staff use on 3 departments
    It would be a lot of work to do it the official way. Best to read the riot act to the employees.  Assign one person in each department to administer the device.  Set them up with an apple id.  Set activation lock to apple id.
    Now if you want to learn the business way...
    "This document offers guidance on some important considerations for getting the most out of your iOS deployment." Covers: Prepare your infrastructure.  Set up devices.  Configure and manage devices.  Deploy apps and content.  Plan for support.
    https://www.apple.com/ipad/business/docs/iOS_Enterprise_Deployment_Overview_EN_F eb14.pdf
    Quick overview of zero-touch MDM enrollment, DEP
    http://www.apple.com/education/it/dep/
    Consider DEP, Device Enrollment Program. Use VPP, Volume Purchase Program.  Select an MDM, Mobile Device Management.  Read the Google doc below and nsdjoey write up.
        MDM --  Mobile Device Management 
          For a comparison see this page:
          http://www.enterpriseios.com/wiki/Comparison_MDM_Providers
          meraki -- is free.
          maas360 -- has a lot of features
        VPP -- Volume Purchase Program
          http://www.apple.com/education/it/vpp/

  • One XML for whole project?

    I am dynamically loading images into my project using xml. If possible I'd like to use one xml file for the whole project and target different parts of the xml file. How can I target different parts (or children?, please correct me if I am wrong) of the xml file?
    Ex:
    <murals>
         <image .....>
    </murals>
    <trompe>
         <image .....>
    </trompe>
    Only access the images in the murals section when wanted and only access the images in trompe when wanted and so on.
    THANKS!

    Well, this is what I have here. I don't know if it is E4X or not.
    var imageLoader:Loader;
    var xml:XML;
    var xmlList:XMLList;
    var xmlLoader:URLLoader = new URLLoader();
    xmlLoader.load(new URLRequest("xml/gallery.xml"));
    xmlLoader.addEventListener(Event.COMPLETE, xmlLoaded);
    function xmlLoaded(event:Event):void{
        xml = XML(event.target.data);
        xmlList = xml.children();
    .....other stuff

  • Cisco Prime Network Control System (NCS) - Reports

    Hiya Supporters !
    Just wonder how to make a report showing me which AP's in my setup that NEVER have any associated clients on, and/or over a given period of time, like 1 or months.
    seems like I can get some reports under :
    reports - report launch pad - clients
    but i can not get clients count = 0 by "AP name"
    anyone know how ?
    I use WLC's versions 7.0.116 and NCS 1.0.2.29 appliance on ESX

    mbilgrav,
    There is a command on the NCS CLI that looks interesting:
    # ncs db reinitdb
    wilab-ncs/admin# ncs db ?  reinitdb  Reinitialize NCS database by dropping all the tables
    DISCLAIMER: I'm not a database guy, I've never used this command, and I have no idea what the ramifications are (I've searched and haven't found much). If you do decide to try it, snapshot/backup first and proceed at your own risk.
    UPDATE: Curiousity got the best of me and I ran this command on my own lab NCS. I can confirm that this wipes out the NCS database completely and dumps you back to defaults. All user accounts except root are deleted, along with maps, devices and settings. The only thing that appears to be preserved is licensing. So... this could be useful if you wanted to re-attempt a WCS database migration: You could delete the offending AP entry within WCS first, then migrate your db over to NCS and presumably it would import without this AP record. That's assuming you came over from WCS in the first place, which I don't think you mentioned.
    Other than that, you could try TAC. It sounds like a corrupt database entry or a bug to me, so maybe they can give you a sql query that will clear it out from the CLI or something.
    If it were my system, I would snapshot/backup the 1.0 installation and then upgrade to 1.1. If you don't like the upgrade or if it breaks anything, you can restore your 1.0 snapshot.
    Please let us know if/how you are able to resolve the issue.
    Justin

  • Cisco Prime Network Control System Health Monitor Reflected XSS

    Apologies for the n00b question,
    I am a security manager not a Cisco guru so please bear with me
    Our Nessus scanner has picked this vulnerability up
    Nessus states that there is no fix
    Looking on Cisco's bug search the status is set to fixed, 
    https://tools.cisco.com/bugsearch/bug/CSCud18375
    I found this article on Cisco's website
    Multiple Vulnerabilities in the WLSE Appliance - Cisco 2011-12-10
    There are two vulnerabilities that exist in the CiscoWorks Wireless LAN Solution Engine (WLSE). The first is a cross site scripting (XSS) vulnerability that may allow an attacker to gain administrative privileges on the system. The second is a local privilege escalation vulnerability that can be used by an attacker who already has authenticated access to the command line interface to obtain access to the underlying operating system. Cisco has made free software available to address this vulnerability for affected customers. This advisory is available at http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20060419-wlse
    Is WLSE part of WCS or am I grasping at straws here? Our techies don't seem to think so
    We are currently running CISCO Wireless Controller System (WCS) running on Version 7.0.240.0 which is end of life
    Is there an upgrade path for newer software?
    Has anyone else encountered this issue
    http://www.kb.cert.org/vuls/id/830316

    1. Its possible but some sort of lock/bug is preventing the removal of the controller. Is the controller reachable? Have you attempted to restart NCS to see if you are able to remove the controller afterwards?
    2. 8510 not supported on NCS, you must upgrade to Cisco Prime 1.3.x or higher.
    http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.3/release/notes/cpi_rn_13.html#wp86690
    3.  Follow the upgrade steps for all information regarding patches and migration path:
    http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.3/quickstart/guide/cpi_qsg_1_3.html#wp69624

  • Can I use two different Apple IDs on one device for music?, Can I use two different Apple IDs on one device for music?

    I have a band's album but they are relasing a deluxe album on presale but only for UK.
    I have a pen pal who could send me a UK iTunes card since those are region locked but if I make another Apple ID in the "UK," could I still download it (after switching iTunes store region) on my iPod with my USA songs?
    Sorry if my explination was a little confusing, if you have any questions you can ask me in the comments.

    This would be a violation of the terms of use of the itunes store and could result in the loss of your account.
    You cannot use the U.K. itunes store unless you are in the U.K

  • SAP HANA for Control System Application

    Hi,
    I want to know is there any on going project where SAP HANA is using for the applications of control system (Fuzzy Logic, Predictive control system, modeling etc) for industries like power plant, Oil and gas, aerospace for better results.
    Could any one can share information on this.
    Posted topic is not relevant to this forum. Kindly suggest me where to post this topic.
    Thanks in advance.
    Regards,
    Siva Prasad N

    Hi Sava,
    Maybe the link below will be of help. In there you can find lots of useful HANA information.
    https://community.wdf.sap.corp/sbs/message/108063#108063
    regards,
    David

  • CLD, +MATLAB/SIMULINK/C/C++/VB/ETC, Control systems and robotics, M.Sc., happy to gain worldwide experience, located in Canada

    Hi,
      My name is Morteza Heydari Araghi. I am a Mechatronics Engineer (studied Electrical Engineering during BS and MS, but also worked on Mechanical and Mechatronics projects), and am currently looking for a job that matches my skills. I am willing, and actually happier to relocate, and gain worldwide experience. I would prefer Canada, the US and europe, however I would need a work permit if anywhere outside Canada. I am a self-motivated and focused engineer who sets his goals and works very well in a team to achieve them. Some highlights of my qualifications include:
    Studied Control Systems and robotics for 8 years.
    Certified LabVIEW Developer. Used LabVIEW for about 6 years.
    Worked with NI vision builder for machine vision applications.
    Designed several machine vision systems for industrial purposes
    Worked with real-time and/or embedded systems for more than 5 years.
    Worked with some professional programming software packages, including C/C++ language, VB, MATLAB, NI LabView, SolidWorks, etc.
    Worked with actuation and measuring systems in the sense of design, automation, instrumentation, and robotic applications.
    Finding innovative solutions for highly competitive studies. Sharp in understanding new concepts.
    Should you like to discuss further, please contact me at mheydari  at  alumni.uwo.ca
    Best wishes,
    Morteza

    Respected sir/madam,
    i am surendra babu.now i am looking for a job
    and i have one year experience in LABVIEW.
                            Herewith i have attach my resume.Please take a look.
    if u find any openings on LABVIEW please forward my resume.
    Thanks & Regards,
    Surendra babu Pidikiti
    Attachments:
    RESUME-SURENDRA.doc.docx ‏42 KB

  • What version control system you use?

    We are 20 developer and we use bitkeeper as a version control system.
    But we have 4 envirronnement.
    dev/test/pre-prod/prod.
    Sometimes, 2-3 projects are affecting the same packages.
    And different packages version is all over the place since we have 4 envirronnements.
    What version control system you use for packages?
    Would be cool to have a version control system intergrated to our tools, like toad, pl/sql dev or sql developer, is there one for those tools?
    Is the tool you using it doing all you want it to do?
    Have any link for me to check out?

    Hi,
    I recommend SourceAnywhere Standalone to you. It is an SQL-based source control application that provides all of the key features of VSS, plus much more. It is well integrated with Microsoft Visual Studio 6/2003/2005/2008, Dreamweaver and Eclipse. Here is the home page of SourceAnywhere Standalone:
    http://www.dynamsoft.com/Products/SAWstandalone_Overview.aspx
    The Hosted edition, SourceAnywhere Hosted that is delivered as a SaaS application is also available.
    http://www.dynamsoft.com/Products/SAWhosted_Overview.aspx
    You can take a look.
    Thanks,
    Catherine Sea
    www.dynamsoft.com
    the leading developer of version control and issue tracking software
    Message was edited by:
    Catherine Sea

  • I have songs from icloud showing on more than one device but only want them on one so how do i delete them

    Can some tell me how i can not have the songs showing on more than one device for my account

    Krshrtr wrote:
    it wont let you swipe to the left on songs that have the cloud next to them
    That's correct - it only deletes them from your phone, not from iCloud
    If you go into Settings, Music and set Show All Music to Off, you will only see the songs that are actually on the phone.
    One other tip - once you've deleted the songs/lists you no longer want, restart the phone (hold the Home and Sleep buttons for about 10 seconds until the Apple logo appears) to make sure the songs are gone.

  • Is there an jdev ARCS (appl. revision control system) extension available ?

    Is there an ARCS ( application revision control system ) extension available for Jdeveloper ?
    Googling took me to OAF developer guide which said -
    "With the ARCS (Applications Revision Control System) Extension for JDeveloper, you can perform most
    source control tasks without leaving JDeveloper. For additional information about enabling and using this tool,
    see the E-Business Suite Application Development Services ARCS Extension for JDeveloper web page."
    Can someone point me where to look for this page ? ( I am in Oracle Intranet, so it is accessible for me even if it is an internal page )
    Thanks

    Hi,
    source code control is through Subversion (recommended). For more read up about Team Productivity Center - http://www.oracle.com/technetwork/developer-tools/tpc/overview/index.html
    Frank
    Edited by: Frank Nimphius on Aug 18, 2011 11:23 AM

Maybe you are looking for