Network controller& USB controller driver not found and wifi not working
hello I Purchased HP 15-ac025TX (M9V00PA) Notebook laptop . i have installed all driver from HP site here is the link http://support.hp.com/in-en/drivers/selfservice/HP-15-Notebook-PC-series/7771404/model/8326084#Z7_3054ICK0KGTE30AQO5O3KA30R1 but still netwok controller driver not found also wifi not working i installed blutooth drivers too . I am using window 7 sp1 (32 bit) For network controller device ID is PCI\VEN_14E4&DEV_4365&SUBSYS_804A103C&REV_01 secondly univeral serial bus driver(usb) controller not found i installed all drivers from above link also update windows but still no solution hardware id of usb controller is PCI\VEN_8086&DEV_9CB1@SUBSYS_80C2103C&REV_03 and last i am unable to download AMD/Intel Switchable High-Definition (HD) Graphics Driver. the download link not working KINDLY RESOLVE THE ISSUE THANK YOU
Update: While the driver I knew would work has not shown up yet, I did some detective work and explored some other broadcom wireless card driver folders from some HP links, and I found one that should work for you. While it says it is for HP desktop PC's, they put the exact same wireless card form factor in a desktop PC that they do in a notebook PC. I see no reason why this driver would not work, since the setup information file contains the same hardware ID that you posted. Here is a partial copy and paste of the driver setup information file and you can see the hardware ID you posted is supported by this driver. x86 - Win7
[BROADCOM.NTx86.6.1]
%BCM430N_DeviceDesc% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_2230103C
%BCM430N_DeviceDesc% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_22D3103C
%BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_2232103C
%BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_22D4103C
%BCM430N_DeviceDesc_HPY% = BCM43XNG_NT61, PCI\VEN_14E4&DEV_4365&SUBSYS_804A103C http://h20566.www2.hp.com/hpsc/swd/public/detail?swItemId=cp_149257_1
Similar Messages
-
Why when I tried to update itunes it crashed and now I get a MSVCR80.dll was not found and can not start my itunes any more?
Solving the iTunes Installation Problems in Windows
1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80. -
Yesterday I updated my Itunes account and it stopped working. I tried installing itunes version 11.1.4 and once done it came back with 2 error messages MsvCR80.dll was not found and I tunes was not installed correctly Error 7 (windows error 126) I have removed Itunes completely and redownloaded several times with the same result. Is there an easy fix or can I download an older version of Itunes that works?
None of the solutions mentioned in this forum work for me. I've not ever had a problem with your software before. I installed and uninstalled itunes 3 times. No itunes directories exist. I've uninstalled everything labled Apple on my pc withe the same results. The problem is with your software not Windows.
-
Upgrading to 11.1.1.2, registry.xml not found and oracle_common not found
We are running OFM 11.1.1.1, with the OID component only (and no weblogic domain). We're trying to upgrade to 11.1.1.2, and when running the ant master-patch-schema command, we're getting the following errors:
validate-file-exists:
[echo] Error: ** file location /ora01/app/oracle/product/middleware/Oracle_IDM1/registry.xml is not found
validate-file-exists:
[echo] Error: ** dir location /ora01/app/oracle/product/middleware11g/oracle_common is not found
Has anyone seen this before?
TIA,
Eileen
Edited by: EileenRoach on Sep 29, 2010 5:03 PMI worked through this issue with the assistance of Oracle Support. What we ended up doing was the following:
1) Install (do not configure) the 11.1.1.2.0 verion
2) patchMaster.properties should have these values filled in:
patchMaster.Componentlist=OID
patchMaster.Schemaurl=jdbc:oracle:thin:@<hostname>:<port>:<sid>
patchMaster.Schemauser=SYS AS SYSDBA
patchMaster.Schemaprefix=ODS
patchMaster.Mwhomenew=/ora01/app/oracle/product/middleware11g
patchMaster.Mwhomeold=/ora01/app/oracle/product/middleware
patchMaster.Oracleinstancenewlist=/ora01/app/oracle/product/middleware11g/asinst_1
patchMaster.Oracleinstanceoldlist=/ora01/app/oracle/product/middleware/instances/asinst_1
patchMaster.Oraclehomenew=/ora01/app/oracle/product/middleware11g/Oracle_IDM1
patchMaster.Oraclehomeold=/ora01/app/oracle/product/middleware/Oracle_IDM1
patchMaster.Loglevel=debug
patchMaster.ValidationErrorContinue=true
The ValidaitonErrorContinue=true basically means ignore errors and continue -- so we ignored the files not found errors.
3) run the 'ant master-patch-schema' command
4) run the 'ant master-patch-oinstance' command
5) copy the wallets folder and files (the ewallet.p12 and cwallet.sso files did not get migrated)
6) Modify environment variables and custom start up scripts for new middleware and instance home directories -
"Serial Number Not Found" and battery not charging
Hi,
I have a problem with my Compaq mini 110c 1030sf. It started a few months ago, when a weird red message appeared on the Compaq boot logo : "Serial Number Not Found".
Everything was still working fine though, that's why I did not try to fix it.
However, about a month ago, when I started the computer (it had been inactive for three weeks), the battery was not charging. Since then, I can't run the computer using the battery, I have to let the AC adapter plugged.
Windows said : 0%, not charging.
Ubuntu says : 0%, completely charged
I removed the battery and put it back, it started to charge, but stopped after 3 or 4 seconds.
I also tryed updating bios, but it changed nothing.
Could anyone please help me ? ^^If your mini is still within warranty contact HP.
Have you tried the battery test in the HP Support Assistant?
Your BIOS has issues if you have seen that message. That is something you cannot correct on your own as it requires HP's proprietary software to enter the information in the BIOS.
Best regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer -
Itunes 12 track names not found and user not registered for online use
I recently downloaded itunes 12, and now when I try to import a CD the track names or CD information is not found.... So when I click on options to Get Track Names....it tells me user is not registered for online use... I am running windows 7.
I have tried un-installing and re-installing - didn't work.
I have tried removing a file and then have it repaired... didn't work.
Any other ideas on how to solve this problem?You could try deleting the entire %appdata%/Apple Computer folder or look for parallel files/folders in the C:\Users\<User>\AppData\Local or C:\Users\<User>\AppData\LocalLow folders in case a corrupt file is persisting there.
Or it might not be the preference files after all...
For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
tt2 -
I can't connect to my own network after the upgrade. Is anyone else having this problem.
A lot of people are having this problem. A simple search on this discussion board will tell you. A bunch of solutions are offered here and there to try so have fun...
Here is one:
Go to Settings>Safari>Clear History, Cookies and Data. Restart the iPad. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button. -
Headphones are not found and do not work
Hello
After I got my laptop, HP Envy 15 j000eb, back from the computer store where they put a new keyboard in it (spilled soup), I found that I cannot longer use my headphones: when I put my headphones into the audio jack, the sound keeps coming from the laptop speakers, and nothing is heard coming from the headphones (tried with several headphones, they work fine on other computers).
I updated the audio driver with a download found on the hp site (http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4158&lc=en&cc=us&dlc=en&sw_lang=&product=5390... as suggested in another question on this forum, but the problem stayed the same.
My audio worked just fine untill before I gave my laptop in for reparation.
What should I do? Is there another easy way to fix it or is it a hardware issue?
This question was solved.
View Solution.Hello Simon42,
I see that after having the notebook in to a shop for repairs with the keyboard, it is no longer recognizing the headphones. I will try to assist you.
To start, as it wasn't in your post I recommend the basics.
1) Test the notebook with another set of headphones, just to verify that it's the jack or that headphones are working at all. If you have them or know someone even try a usb set.
2) Test the headphones, plug them into something else to make sure they are working correctly.
This will indicate if the issue is the notebook or headset. It more then likely is the notebooks headphone jack, but it's always worth testing to be certain.
From that point, if it is the notebook I'd recommend contacting support for repair/replacement options.
HP Technical Support, North America 1-800-474-6836. For all other regions click here.
Thank you for posting on the HP Forums.
I worked on behalf of HP. -
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that
the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)(Microsoft SQL Server, Error: 2)
The system cannot find the file specified
Cannot connect to COWBOYS.
Here are the technical details===================================
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider:
Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft%20SQL%20Server&EvtSrc=MSSQLServer&EvtID=2&LinkId=20476
Error Number: 2
Severity: 20
State: 0
Program Location:
at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer
timeout)
at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance)
at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance,
SqlConnectionString userConnectionOptions, SessionData reconnectSessionData)
at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal oldConnection, DbConnectionInternal& connection)
at System.Data.ProviderBase.DbConnectionInternal.TryOpenConnectionInternal(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.SqlClient.SqlConnection.TryOpenInner(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.Open()
at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server)
at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser()
===================================
The system cannot find the file specified
I have tried from so many forms. This is so frustrating. Thank for everyone/anyone who wants to help. So this is what happened: I had to uninstall my previous sqlserver 2012(which worked great) for some reason, and I uninstalled everything from that download.
Then I installed the trial edition of sql server 2012 (64 Bit) and It wouldn't connect to the database. (Error mentioned above.) My local DB is COWBOYS. (COWBOYS is also my computer name.) After this, I have tried downloading sqlexpress and sqlserver 64bit
many times and cannot connect to my local DB.
How do I connect to my Local DB?
Also, I think this might help: (When I run sqlserve.exe, which I was able to find in C:\Program Files\Microsoft SQL Server\110\LocalDB\Binn, I get an error: Your SQL server installation is either corrupt or has been tampered with(Error getting
instance ID from name). Please uninstall then re-run setup to correct this problem.
I would happily re install it, if it wasn't my 20th time.
I don't have any remote connections, I don't use username/password, only window authentication. I work mostly on visual studio, but without able to store /retrieve data, I don't know how to survive.
May be the solution is very simple, but I am too frustrated.
Some of the things I have tried:
From a command prompt, enter one of the following commands:
net start "SQL Server Agent (MSSQLSERVER)" OR
net start "SQL Server Agent(instancename)"(for instance)
on my sql configuration, I cannot start anything because there is nothing there to start. I can post more details, if that would help. Also, some more details about the error:
Details
Product:
SQL Server
ID:
2
Source:
MSSQLServer
Version:
10.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Version:
9.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Any one that can help me, I will be greatful. Thank you so much. p.s. please ask me anything if you have any questions.It sounds like there are a couple things going on here. First check if you have a successful install of SQL Server, then we'll figure out the connection issues.
Can you launch SQL Server Configuration Manager and check for SQL Server (MSSQLSERVER) if default instance or SQL Server (other name) if you've configured your instance as a named instance. Once you find this, make sure the service is started.
If not started, try to start it and see if it throws an error. If you get an error, post the error message your hitting. If the service starts, you can then launch SSMS and try to connect. If you have a default instance, you can use the machine
name in the connection dialog. Ex: "COWBOYS" where Cowboys is the machine name. However, if you named the SQL Server instance during install, you'll need to connect using the machine\instance format. Ex: COWBOYS\Romo (where Romo
is the instance name you set during install).
You can also look at the summary.txt file in the SQL Server setup error logs to see what happened on the most recent install. Past install history is archived in the log folder if you need to dig those up to help troubleshoot, but the most
recent one may help get to the bottom of it if there is an issue with setup detecting a prior instance that needs to be repaired.
Thanks,
Sam Lester (MSFT)
http://blogs.msdn.com/b/samlester
This posting is provided "AS IS" with no warranties, and confers no rights. Please remember to click
"Mark as Answer" and
"Vote as Helpful" on posts that help you. This can be beneficial to other community members reading the thread. -
ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified in windows server 2008 r2.I made a application in asp.net c#.I am using ODBC connection.When I deployed my application in windows server2008 r2.There
is no Microsoft ODBC driver shown in ODBC Data source administrator.Then I go to the C:\Windows\SysWOW64 and open Odbcad32.exe and add Microsoft ODBC2 driver for Oracle and when I run my application I got following error
ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified
I am using follwoing string
<connectionStrings>
<add name="theconnetion" connectionString="DSN=abdb;UID=abc;PWD=xyz"/>
</connectionStrings>
Guide me What I do?Did you add a System DSN or a User DSN? If you added a User DSN from your own login, the asp.net application will not be able to use it unless its application Pool in IIS is configured to run under the same credentials that you used for creating
the DSN. It's better if you add a System DSN.
Also, be careful to ensure that you are using a 64 bit DSN, unless you configure the application to run in 32 bits. If the 64 bit application attempts to use the 32 bit driver you get the same error message "Data source name not found and no default
driver specified". See this KB article:
http://support.microsoft.com/kb/942976/en-us -
hi ,
when generate the schema , i got the below error, please any one put your inputs:
Connecting to the LOB system has failed. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server
is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server).thaks shanky,
but facing another , after generate schema from WCF_SQL, im unable get elements in my schema.
this is schema generate from storeprocduer , but thru WCF-sql im unable get the elements like
id, name
<xsd:schema targetNamespace="urn:schemas-microsoft-com:sql:SqlRowSet2" xmlns:schema="urn:schemas-microsoft-com:sql:SqlRowSet2" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:sqltypes="http://schemas.microsoft.com/sqlserver/2004/sqltypes" elementFormDefault="qualified">
<xsd:import namespace="http://schemas.microsoft.com/sqlserver/2004/sqltypes" schemaLocation="http://schemas.microsoft.com/sqlserver/2004/sqltypes/sqltypes.xsd" />
<xsd:element name="Test.dbo.sample">
<xsd:complexType>
<xsd:sequence>
<xsd:element name="id" type="sqltypes:int" minOccurs="0" />
<xsd:element name="name" minOccurs="0">
<xsd:simpleType>
<xsd:restriction base="sqltypes:nvarchar" sqltypes:localeId="1033" sqltypes:sqlCompareOptions="IgnoreCase IgnoreKanaType IgnoreWidth" sqltypes:sqlSortId="52">
<xsd:maxLength value="1000" />
</xsd:restriction>
</xsd:simpleType>
</xsd:element>
</xsd:sequence>
</xsd:complexType>
</xsd:element>
</xsd:schema>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>19</id>
<name>sw</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>14</id>
<name>swe</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>13</id>
<name>se</name>
</Test.dbo.sample> -
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The
server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26- Error:Locating Server\instance Specified)
How Can i solve this?1. Make sure SQL Server Service is running
2. If a named instance, make sure SQL Server browser service is running
3. Make sure SQL Server is configured to allow remote connections
4. Examine the SQL Server error log for messages confirming that SQL is listening on the expected network interfaces and ports
5. Test server connectivity with PING from the client machine
6. Test port connectivity using TELNET or PowerShell to the server and port (from step 4) from the client machine. For example
a. TELNET <server-name> 1433
b. PowerShell: 1433 | % { echo ((new-object Net.Sockets.TcpClient).Connect("YourServerName",$_)) "server listening on TCP port $_" }
7. Check firewall settings if step 5 or 6 connectivity test fails
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Consulting:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance
SQL Server Integration Services:
Business Intelligence -
Hey everyone, So I am trying to get a report onto the server, and in BIDS I kept getting a login screen repeating over and over when I tried to deploy my report, so I tried to upload the file at http://<servername>/Reports This worked, but then trying
to run this report from http://<servername>/Reports did not work either because "An error has occurred during report processing. (rsProcessingAborted) Cannot create a connection to data source 'FTYDataSource'. (rsErrorOpeningConnection) For more information
about this error navigate to the report server on the local server machine, or enable remote errors" Anyways I tried to add a New Data Source (which I would use in the report) at http://<servername>/Reports, type ODBC, with the connection string Dsn=blah_blahblah.
I try to test the connection here and get the error ERROR [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified This is really getting old fast, everything I try, a new error comes up. Granted I am new at this,
but this still should not be this troublesome. Does anyone have any ideas on what could FINALLY allow me to just put a report out onto the server?!? THANK YOU in advance for ANY help.Hi,
Please try setting the credentials of the datasource.
1. Double click and open the datasource in your project.
2. Click on the credentials tab, and click on option button 'Use this username and password'
3. Enter the username and password to connect to the datasource
4. Deploy or upload the datasource to the report server and try accessing the reports.
Hope this helps.
Please click "Mark as Answer" if this resolves your problem or "Vote as Helpful" if you find it helpful.
BH -
Hi I have SQL2012 installed on my local machine and have also installed MySQL 5.6.23 installed with a test database.
I also have my SQL connector installed and MYSQL ODBC Driver 3.51.
Which happily connects to the Mysqldb.
The Datasource Name : mySQL conn
TCP/IP Server : localhost and Port :3306
User root
with pwd
On the SQL side I have used the following
EXEC master.dbo.sp_addlinkedserver
@server = N'MYSQLSRV',
@srvproduct=N'mySQL conn',
@provider=N'MSDASQL',
@datasrc=N'mySQL conn'
However when I try to selet using open query
SELECT * FROM OPENQUERY ( [MYSQLSRV], 'SELECT * FROM students' )
it comes back with
OLE DB provider "MSDASQL" for linked server "MYSQLSRV" returned message "[Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified".
Msg 7303, Level 16, State 1, Line 1
Cannot initialize the data source object of OLE DB provider "MSDASQL" for linked server "MYSQLSRV".
I cant understand what I have done wrong . Any help in this would be great as Ive hit a bit of a brick wallHi Robert3975,
In addition to other post, please also note the following things.
1. If you use the 32-bit driver on a 64-bit machine, please run the 32bit version of "odbcad32.exe" by running "c:\Windows\SysWOW64\odbcad32.exe"
from Start/Run menu and
create your ODBC DSN. However, for the 64-bit driver, use c:\windows\system32\odbcad32.exe to create your ODBC DSN. For more details, please review this similar
thread.
2. Expand the folder Providers under Linked server directory in SSMS and go to properties of MSDASQL provider and configure it properly as described in this blog:
Creating Linked server to MYSQL from SQL Server.
Thanks,
Lydia Zhang
If you have any feedback on our support, please click
here.
Lydia Zhang
TechNet Community Support -
Error: Datasource name not found and no default driver specified
HI All,
I have MySQL as my data base.
I created one universe on top of MySQL. Then i made one webI report on top of that and exported it to BO Portal (Infoview).
Now when I am refreshing this report, it gives me below error in Infoview while its getting refreshed in WebI.
[Database Error] [Microsoft ODBC Driver manager] Datasource name not found and no default driver specified.
WIS 10901
I found SAP Note 1200396 and have created DSN with Same name on Server.
But still I am facing same problem. I have not clustered enviroment.
Guys any one have some idea about this?
I will appreciate your answer.
Thanks in advance,
RishitIf your BOBJ server runs on 64bit windows you should set up the DSN using the 32bit ODCB utility (<Windowa installation director>\SysWOW64\odbcad32.exe )
Regards,
Stratos
Maybe you are looking for
-
How to import data from a text file into a table
Hello, I need help with importing data from a .csv file with comma delimiter into a table. I've been struggling to figure out how to use the "Import from Files" wizard in Oracle 10g web-base Enterprise Manager. I have not been able to find a simple i
-
i really need to know how
-
Dear All, My client requested for the GL account that was originally maintained as 'line item display' only, to make it 'open item management' also. Now we have list that contains both line and open items, and they can not close it (it always remains
-
Using find my iphone while roaming without notifications activated
Hello, I used to be able to use "Find my iPhone" while roaming internationally without have push notifications on (iOS 4.x.x.) but now with iOS 5 there isn't a way to use that feature without enabling notifications as well. In Settings>General>Networ
-
raise to speak is no longer a selection under Settings and it's no longer working. Did they do away with this feature?