Network Downtime measuring with CW LMS 3.1

We have a network of about 750 Devices. We have implemented LMS 3.1 as a primary NMS in our NW. Now we want to measure total downtime in a month through CW LMS. How to do that ?

Really, there's no one report that gives you this. If you're using the Health and Utilization Monitor add-on, you can create pollers to monitor DEVICE availability. You can then run reports to see what the availability was over a given amount of time.
IPM can also do service-level availability tracking. That is, you can setup an IP SLA collector to monitor a given service on your network (e.g. an application server, host, etc.), then run reports to get that service's availability.

Similar Messages

AC resistivity measurement with MyDAQ on TEC

Hello,
I would like to ask for advice: we would like to measure resisitivity of Peltier-elements. If we use DC method, because of the Seebeck-voltage of the element, we do not get the real resistivity value. The common method to use AC measurement in case of such devices. I would like to know, if it is possible to use a MyDAQ device for this task? As a first approach we do not need the best accuracy, this would be more as a "broken-element" test (there is usually a significant shift away from the nominal AC resistivity value stated by the manufacturer).
What would be the easiest way to carry out a simple measurement? What about if I use one analogue output of the MyDAQ lets say with 1kHz, and I drive the Peltier-element with this voltage AC source? And I connect a known resistor in series, and I measure the AC voltage drop on this. From this data, I could calculate the current, and the AC resistance of the Peltier-element? Of course I have to choose a resistor so the MyDAQ can drive the network.
what is your opinion, where to start?
Thanks!
Solved!
Go to Solution.

Hello, thanks for the reply!
Actually I am just going to replace 60 Peltier elements in a "home-made" 15 years old heat exchanger (I expect to find some mice too ). This assembly has dropped performance (heat transfer power) and also I know that, a few years ago after a malfunction with the hot side cooling fans, this device was running for a certain time without forced cooling. What is quite bad in case of Peltier-elements. I have already bought 65 brand new Peltier-modules and after I get some heat conducting paste, I will replace them. And I will have 60 pieces of old Peltier modules, to play with them
Since I have this NI MyDAQ, I thought it would be fun (and would give also valuable information) to try to measure the old elements' AC resistivity. Since this task is not like I should do often, so for first, I would not like to go for more pro solutions, I will try the MyDAQ first.
I expect that some of the modules got structural degradation during the heat shock, and this may be measurable in a shifted AC resistance.
I would do the measurement with zero applied DC voltage. These modules are Melcor PT3-12-30L (discontinued product), the nominal module resistance is about 5 Ohm.
EDIT: and would you recommend a certain circuit to try? Shell I use a known resistor for current measurement via measuring the voltage on it? Or I could use a known AC current to drive the Peltier, and I would measure the resulted AC Voltage on it?

Can I create a Capivate 6 course that plays offline and synchs with our LMS?

Can I create a Captivate 6 course that plays offline and synchs with our LMS?

Hi there,
Welcome to Adobe Community.
Unfortunately, I do not seem to remember any possible way to have a course offline and then synch it with the LMS.
If you do not have an internet connection and within a local network then you could try internal server reporting.
The below thread could be of some help:
http://forums.adobe.com/message/5120619#5120619
Thanks!

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either.

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either. I have an iphone 4 that will not connect to 5ghz.
thank you!

Your AirPort Express is already providing two separate 2.4 GHz and 5 GHz bands, but each band is using the same wireless network name.
This is the default setup for the AirPort Express, which is recommended for most users. The theory here is that devices will automatically connect to the best quality signal based on their capabilities and distance in relation to the AirPort Express.
It is possible to assign a different name to the 5 GHz band, and then "point" devices at that network to connect. Some users swear by this option.....(I am not one of them).... but you might want to give it a try to see how it works for you.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Express
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options near the bottom of the next window
Enter a check mark next to 5 GHz Name.....which will automatically add "5 GHz" to the network name....so you can identify it
Click Save, then click Update and wait a full minute for the Express to restart
Now you will need to "point" your 5 GHz capable devices at the 5 GHz network name. 2.4 GHz devices will connect to your "other" network name.

How to use external timebase for Two Edge Separation measurement with PCIe 6351

Hi
I am working with PCIe 6351 x series DAQ card.
counter measurements.
Here i need to measure the time/no edges between two edges. Falling to Raising of two signals.
I got the measurement with internal time base.
here i need to synchronize the measurements with external clock from the external setup.
so i need to use that external clock,timebase for the counters.
Any solution please..
Regards,
Hari

First, the VI you mention is NOT for STC timer/counters. Therefore, it won't work.
If you want to get the time interval between two edges, you want to use the Functions -> Data Acquisition -> Counter -> Count Events or Time VI. This will do the function you are looking for.
Mark

Using a network-stored catalog with Mac OSX

Greetings all.
I am using Photoshop Elements 11 on Mac OSX Mountain Lion and want to store my catalog on a local network drive (FreeNAS). I have encountered many problems while attempting to do this. Then I noticed in the Elements Organizer help, under the section "Repair a catalog", the following: "Note: (Mac OS) You cannot access catalogs present on a network drive."
Is this true. or has someone found a workaround to the problem?
Thanks!
--John

Thanks, for that ( I assume we have to carry on in English due to forum policy even though we are both of German tongue I assume)
You mean the access problems are part of the "no network drive" thing? I suspected that. Took me a whole day in front of my computer to realign the mess. So should one better not use the network drives at all? Quite a pity in times where everybody seems to use network storage.
No, I did not use organizer to use the photos. So there is no way to reconnect them? Should I delete the catalogue and start with the photos from scratch?
Regards
Andibuch
Am 02.01.2013 um 23:35 schrieb Barbara B.:
Re: Using a network-stored catalog with Mac OSX
created by Barbara B. in Photoshop Elements - View the full discussion
Well, yes, these are part of the "no network drive" thing.
As for moving the photos, did you use organizer to move them? You will always have trouble if you move photos outside of organizer, even on the same drive--you have to let it manage your photos or it doesn't have a clue as to what happened.
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/4963270#4963270
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4963270#4963270
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4963270#4963270. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Photoshop Elements by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

"Error intitializing communications with the LMS" in Captivate 8.0.1

After updating to 8.0.1.242 and publishing projects as SCORM 1.2 in html5, I get the error message "Error intitializing communications with the LMS" both in the LMS we use and in ScormCloud. This happens in IE 10.0.9200. I am pretty sure we have not had this message before. I had a colleague generate the same project for me using 8.00.145 and I get no error message. Any input on what causes this would be appreciated.

Can you share your project on id: [email protected]
we will try to investigate this at our end. Also please send the exact steps how you are able to get this error.
Regards
Shriyansh
Adobe Engineering Team

Unit of measure with language Key

Hello Guruz,
WHile creationd of purchase order, there is a check kept which compares the vendor communication language which gets updated in the Po header - Communucation tab with Db table T006A which holds the Unit of measurements with Language Key and pops up an error message.
It cheks the order unit in the PO, and the T006A whether the unit is maintained in the Language key as in the PO header - Communiction tab.
But while creating a unit of measurement in CUNI, we dont have the option to maintain the language key for the UOM.
In CUNI, it defaults the language key as EN in table T006A.
I need a prompt support from you guys on this issue. Please suggest how to go about with this?
Best Regards
Greg.

Hello,
When i am trying to go for the language key in CUNI, it says that the said language is 'not available in server'. I guess it is checking whether the language patch is updated in the server.
But it doesn't sound logical to maintain all the unit of measurements in all the vendor languages. Suppose if we are having vendors with 75 communication languages and we are having 50 units os measurements, so does that mean that we have to maintain units of measurements 75 X 50 times ?
Kindly provide your inputs on the issue. We are facing lots of issues with this control kept in PO header checking for the T006A with the vendor communication language.
Regards
Greg

Networking a PC with my Mac

I want to network a PC with my Mac. I did buy a router but was told be customer service of the router company that they did not support Mac software. I had my network up for about a half hour.
I need to know what router to buy for my network. The PC needs to be wired, but I would like to use my wireless airport. What router should I buy?

"I did buy a router but was told be customer service of the router company that they did not support Mac software"
Routers use platform independent, industry standard network protocols. Therefore while the company says they don't support Macs...they are probalby just talking about their own software for configuring the router.
I've used routers and switches over years from just about every common maker...Linksys, NetGear, Asanté, D-Link and they all work with a Mac, so chances are yours works too.
If you really want one labeled Mac compatbile, buy an Apple Airport Extreme Base Station.

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

I currently have a D-Link DI-604 broadband router with windows computers. How can I add wifi to the network for use with ipad? Can I use AirPort Express?

Yes. You can directly connect an 802.11n AirPort Express Base Station (AXn) using an Ethernet cable. The AXn would then just need to be configured as a bridge to allow the D-Link to continue to provide both NAT & DHCP services for all network clients connected to either router.
In this configuration, the AXn would broadcast a wireless network for your wireless network clients to connect to.

Samples Not Acquired on NI 660x or NI 6624 Devices When using pulse width, semi-period or two-edge separation buffered measurements with the NI 660x and NI 6624 on counters 0 and 1, some samples may not be acquired under certain circumstances.

In the DAQmx 9.4 Readme the following is stated:
Samples Not Acquired on NI 660x or NI 6624 Devices When using pulse width, semi-period or two-edge separation buffered measurements with the NI 660x and NI 6624 on counters 0 and 1, some samples may not be acquired under certain circumstances.
Could anyone elaborate on this? I am particularly interested in knowing under what circumstances this problem arises for the 6602 PCI devices.
How should I understand 'NI 660x and NI 6624 on counters 0 and 1'. Is it only a problem on counter 0 and 1 for the 660x or does this only apply for the 6624 devices.
/mola

Are there any NI Product Support Engineers out there who has an answer to this question and who are willing to share it with me?

I have just purchased an iMac for home - am I able to network an iMac with a windows laptop?

I have just purchased an iMac for home - am I able to network an iMac with a windows laptop?

It sounds really unlikely though... You have to type in your password twice when setting up so you either:
made the same typo twice
the caps lock was on
You held down SHIFT during one of the letters
the keys have relocated because of different language keyboard layout
you simply forgot exactly what you typed.
Are you aware that passwords are case-sensetive? also, when using punctuation in passwords be aware that language localization of the keyboard can cause relocation of certain symbols like $ and € and * and ' which may make it impossible to retype the password correctly, if you are unaware of the correct way to type a certain puntuation symbol.

Steps: SNC (Supplier Network Collaboration) Integration with ECC through XI

Hi,
Has anyone worked on the SNC(Supplier Network Collaboration) integration with SAP ECC via SAP XI.
Could you pls share any documentation related to this. And also could anybody tell me the setup required to go ahead with the integration.
Thanks,
S

Hi Xavier,
SNC integration with XI has predefined mappings. So ask your basis guys to download the XI content for SNC using with PI. Once they deployed you will have a builtin predefined content in XI. Within the predefined content mostly they all are xsl mappings.
If your requirement is with the standard idocs then you can use them directly. Else if their is customization they you may need to change the mappings according to your requirements.
Also check this help:
http://help.sap.com/esoa_scm_snc2007/helpdata/en/index.htm
Regards,
---Satish

Personal recruitment How to do new measure with function call Update IT4000

Hi out there and happy new year to forum,
i want to update to implement a recruitment measure (Transaction PB40). I did it already with batch input, but i guess it's much more comfortable to do with funtion module, bapi or calsses.
After choosing the measure, the infogroup will be processed. So i guess, i just have to use the corresponding function modules to update the infotypes in a given sequence. is this suggestion right?
What are these function modules? How to update f.e. IT4000? Does anyone has a coding snippet?
Is it HR_INFOTYPE_OPERATION?
In our Infogroup there are also customer specific infotypes f.e. 9***. Can I use the sap standard function modules for "own implemented" infotypes?
I also appreciate an abap oo pattern or any similar....
Best regards,
T

Andy Goris wrote:
But I don't think that it's possible to hire an application completly with function modules (there is no PERNR in the beginning so I would keep the BIM).
The applicants already exists in system, i just want to implement a measure with exact one click!
Otherwise there is a BAPI for applicant_create.
I'm not very expierienced focussing the implementation in pa-recruiting. I'm really looking for a good documentation or anything like that f.e. sap press.
Andy Goris wrote:
... but why would you use the old recruiting database? This is hardly used anymore.
What are the alternatives to it. (I'm not looking forward to upgrade releases or using wd4a or webgui). we are on ecc 6.0 There is already a lot of z-coding in recruitment. We are also using an self implemented e-recruiting approach
Edited by: Timo Ehl on Jan 3, 2012 2:30 PM

Network Downtime measuring with CW LMS 3.1

Similar Messages

Maybe you are looking for