Network dropping with WRT54GS

The network drops 3-4 times daily.  Got this router, as an upgrade from the B, about 2 months ago. 
The only way to get the network back is to unplug all cables, pull the power, let it reset, then do a repair on the Local area Connection.
I am securing it with a WEP key, it has a SSID, other than that if you can help me I can give more information.
It drops for all three computers on the network.  The desktop is physically connected, and the two laptops are wirelessly connected.
Please help this extremely frustrating.
Dwayne
EDIT --> it's version 6
Message Edited by dwharmsway on 05-29-200710:16 AM

I'm having the same problem on my end.
This has been a problem with Linksys routers for some years now. First one I had back in 2002/2003 had the same problems and they never were resolved.
It shocks me that they still suffer from this. I have not used routers for the last 3 years and when I decided to get one I went for Linksys because I like their interfaces. I figured they had fixed that problem from back then.
Seems they haven't as I have to unplug my cables at random intervals for the network to work again.
It just dies without any warning, kills the internet connection and the network in general.
Seems I will have to return this junk and get myself another kind of wireless router. I am using version 6 of it btw.
Any suggestions that won't ruin me?
Message Edited by jobs on 05-31-200706:50 AM
Message Edited by jobs on 05-31-200706:50 AM

Similar Messages

  • Intermittent wired network drops with Realtek NIC

    Running Arch x86_64. The NIC in question is the Realtek 8110SC, which utilizes the r8169 module. After a few minutes (or seconds sometimes) the network interface drops entirely. I can only ping localhost, but all other indications suggest the connection is just fine. There is nothing of note in dmesg or /var/log/*
    This error does not occur with any other OS, nor any other *nix distro that I have tested.

    Hi, are there any other peripherals using the RJ45 ports on the router?
    Are you using a static IP address for the 8600?
    Please mark the post that solves your issue as "Accept as Solution".
    If my answer was helpful click the “Thumbs Up" on the left to say “Thanks”!
    I am not a HP employee.

  • Connection constantly dropping with edimax ew-7612uan USB adapter

    Hi there,
    I have just installed a newly purchased edimax ew-7612uan USB wireless adapter, the problem that I'm getting is that the connection works fine on boot however it keeps dropping very frequently.
    This can be reset by running netctl restart my-network. which is a temporary fix but I can't keep on doing this every 5 minutes or so when the connection drops.
    I don't think there is a problem with the USB adapter as it appears to work fine in windows (I don't work fine with windows though!).
    The same problem has happened on both of my Arch computers... I don't use any other distributions so I don't know if this is an arch specific problem or a general Linux problem. It also happens when using the live disk.
    The old adapter is still installed in the box but once I can get this one working properly it will be removed.
    The output of dmesg is as follows
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.13.8-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.2 20140206 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Apr 1 12:19:51 CEST 2014
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=104c8e28-5731-4470-8911-313aca8c0d0f rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007fedf7ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000007fedf800-0x000000007fedffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000007fee0000-0x000000007fee2fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000007fee3000-0x000000007feeffff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000007fef0000-0x000000007fefffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.4 present.
    [ 0.000000] DMI: HP-Pavilion GB394AA-ABU a6030.uk/LEONITE, BIOS 5.17 04/20/2007
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x7fedf max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CEFFF write-protect
    [ 0.000000] CF000-EFFFF uncachable
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F80000000 write-back
    [ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
    [ 0.000000] 2 disabled
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [mem 0x000f5f40-0x000f5f4f] mapped at [ffff8800000f5f40]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b3e000, 0x01b3efff] PGTABLE
    [ 0.000000] BRK [0x01b3f000, 0x01b3ffff] PGTABLE
    [ 0.000000] BRK [0x01b40000, 0x01b40fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x7fc00000-0x7fdfffff]
    [ 0.000000] [mem 0x7fc00000-0x7fdfffff] page 2M
    [ 0.000000] BRK [0x01b41000, 0x01b41fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x7c000000-0x7fbfffff]
    [ 0.000000] [mem 0x7c000000-0x7fbfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x7bffffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x7bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x7fe00000-0x7fedefff]
    [ 0.000000] [mem 0x7fe00000-0x7fedefff] page 4k
    [ 0.000000] BRK [0x01b42000, 0x01b42fff] PGTABLE
    [ 0.000000] RAMDISK: [mem 0x379ea000-0x37cecfff]
    [ 0.000000] ACPI: RSDP 00000000000f8310 000024 (v02 HPQOEM)
    [ 0.000000] ACPI: XSDT 000000007fee30c0 000054 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: FACP 000000007fee7a80 0000F4 (v03 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: DSDT 000000007fee3280 004798 (v01 HPQOEM SLIC-CPC 00001000 MSFT 03000000)
    [ 0.000000] ACPI: FACS 000000007fee0000 000040
    [ 0.000000] ACPI: SLIC 000000007fee7cc0 000176 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: HPET 000000007fee7e80 000038 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000098)
    [ 0.000000] ACPI: MCFG 000000007fee7f00 00003C (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: APIC 000000007fee7bc0 000084 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: SSDT 000000007fee8460 000304 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000007fedefff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x7fedefff]
    [ 0.000000] NODE_DATA [mem 0x7feda000-0x7fedefff]
    [ 0.000000] [ffffea0000000000-ffffea0001ffffff] PMD -> [ffff88007d600000-ffff88007f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal empty
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0x7fedefff]
    [ 0.000000] On node 0 totalpages: 523901
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 8124 pages used for memmap
    [ 0.000000] DMA32 zone: 519903 pages, LIFO batch:31
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
    [ 0.000000] e820: [mem 0x7ff00000-0xefffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88007fc00000 s86336 r8192 d24256 u524288
    [ 0.000000] pcpu-alloc: s86336 r8192 d24256 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 515692
    [ 0.000000] Policy zone: DMA32
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=104c8e28-5731-4470-8911-313aca8c0d0f rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 2047396K/2095604K available (5271K kernel code, 836K rwdata, 1676K rodata, 1124K init, 1324K bss, 48208K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 8388608 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 2133.881 MHz processor
    [ 0.003339] Calibrating delay loop (skipped), value calculated using timer frequency.. 4269.58 BogoMIPS (lpj=7112936)
    [ 0.003343] pid_max: default: 32768 minimum: 301
    [ 0.003383] Security Framework initialized
    [ 0.003400] AppArmor: AppArmor disabled by boot time parameter
    [ 0.003402] Yama: becoming mindful.
    [ 0.003637] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.004945] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.005645] Mount-cache hash table entries: 256
    [ 0.005953] Initializing cgroup subsys memory
    [ 0.005966] Initializing cgroup subsys devices
    [ 0.005969] Initializing cgroup subsys freezer
    [ 0.005972] Initializing cgroup subsys net_cls
    [ 0.005975] Initializing cgroup subsys blkio
    [ 0.006006] CPU: Physical Processor ID: 0
    [ 0.006008] CPU: Processor Core ID: 0
    [ 0.006011] mce: CPU supports 6 MCE banks
    [ 0.006021] CPU0: Thermal monitoring enabled (TM2)
    [ 0.006030] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
    tlb_flushall_shift: -1
    [ 0.006122] Freeing SMP alternatives memory: 20K (ffffffff819ec000 - ffffffff819f1000)
    [ 0.007776] ACPI: Core revision 20131115
    [ 0.010162] ACPI: All ACPI Tables successfully acquired
    [ 0.013362] ftrace: allocating 21068 entries in 83 pages
    [ 0.023793] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.057912] smpboot: CPU0: Intel(R) Core(TM)2 CPU 6420 @ 2.13GHz (fam: 06, model: 0f, stepping: 06)
    [ 0.059999] APIC calibration not consistent with PM-Timer: 4652ms instead of 100ms
    [ 0.059999] APIC delta adjusted to PM-Timer: 3346453 (155709996)
    [ 0.059999] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver.
    [ 0.059999] perf_event_intel: PEBS disabled due to CPU errata
    [ 0.059999] ... version: 2
    [ 0.059999] ... bit width: 40
    [ 0.059999] ... generic registers: 2
    [ 0.059999] ... value mask: 000000ffffffffff
    [ 0.059999] ... max period: 000000007fffffff
    [ 0.059999] ... fixed-purpose events: 3
    [ 0.059999] ... event mask: 0000000700000003
    [ 0.083418] x86: Booting SMP configuration:
    [ 0.089999] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.083422] .... node #0, CPUs: #1
    [ 0.089999] x86: Booted up 1 node, 2 CPUs
    [ 0.089999] smpboot: Total of 2 processors activated (8538.17 BogoMIPS)
    [ 0.090131] devtmpfs: initialized
    [ 0.093350] PM: Registering ACPI NVS region [mem 0x7fee0000-0x7fee2fff] (12288 bytes)
    [ 0.094547] RTC time: 8:54:04, date: 04/02/14
    [ 0.094607] NET: Registered protocol family 16
    [ 0.094741] cpuidle: using governor ladder
    [ 0.094743] cpuidle: using governor menu
    [ 0.094771] ACPI: bus type PCI registered
    [ 0.094774] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.094845] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
    [ 0.094848] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
    [ 0.094848] PCI: Using configuration type 1 for base access
    [ 0.094952] mtrr: your CPUs had inconsistent fixed MTRR settings
    [ 0.094954] mtrr: your CPUs had inconsistent variable MTRR settings
    [ 0.094955] mtrr: probably your BIOS does not setup all CPUs.
    [ 0.094956] mtrr: corrected configuration.
    [ 0.096731] bio: create slab <bio-0> at 0
    [ 0.096745] ACPI: Added _OSI(Module Device)
    [ 0.096745] ACPI: Added _OSI(Processor Device)
    [ 0.096745] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.096745] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.100165] ACPI: SSDT 000000007fee7f80 000175 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.100379] ACPI: Dynamic OEM Table Load:
    [ 0.100382] ACPI: SSDT (null) 000175 (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.100470] ACPI: SSDT 000000007fee8390 0000CE (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.100675] ACPI: Dynamic OEM Table Load:
    [ 0.100678] ACPI: SSDT (null) 0000CE (v01 HPQOEM SLIC-CPC 42302E31 AWRD 00000000)
    [ 0.100813] ACPI: Interpreter enabled
    [ 0.100824] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
    [ 0.100840] ACPI: (supports S0 S1 S3 S4 S5)
    [ 0.100842] ACPI: Using IOAPIC for interrupt routing
    [ 0.100873] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.100967] ACPI: No dock devices found.
    [ 0.103333] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.103333] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.103333] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
    [ 0.103333] acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.103333] acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
    [ 0.103333] acpi PNP0A08:00: host bridge window [mem 0x7ff00000-0xfebfffff] (ignored)
    [ 0.103333] PCI: root bus 00: using default resources
    [ 0.103333] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
    [ 0.103333] PCI host bridge to bus 0000:00
    [ 0.103333] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.103333] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    [ 0.103333] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
    [ 0.103333] pci 0000:00:00.0: [8086:2770] type 00 class 0x060000
    [ 0.103333] pci 0000:00:01.0: [8086:2771] type 01 class 0x060400
    [ 0.103333] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.103333] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
    [ 0.103333] pci 0000:00:1d.0: reg 0x20: [io 0xff00-0xff1f]
    [ 0.103333] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.103333] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
    [ 0.103333] pci 0000:00:1d.1: reg 0x20: [io 0xfe00-0xfe1f]
    [ 0.103333] pci 0000:00:1d.1: System wakeup disabled by ACPI
    [ 0.103333] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
    [ 0.103333] pci 0000:00:1d.2: reg 0x20: [io 0xfd00-0xfd1f]
    [ 0.103333] pci 0000:00:1d.2: System wakeup disabled by ACPI
    [ 0.103333] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
    [ 0.103333] pci 0000:00:1d.3: reg 0x20: [io 0xfc00-0xfc1f]
    [ 0.103333] pci 0000:00:1d.3: System wakeup disabled by ACPI
    [ 0.103333] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
    [ 0.103333] pci 0000:00:1d.7: reg 0x10: [mem 0xfdfff000-0xfdfff3ff]
    [ 0.103333] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.103379] pci 0000:00:1d.7: System wakeup disabled by ACPI
    [ 0.103420] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
    [ 0.103511] pci 0000:00:1e.0: System wakeup disabled by ACPI
    [ 0.103555] pci 0000:00:1f.0: [8086:27b0] type 00 class 0x060100
    [ 0.103727] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
    [ 0.103741] pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007]
    [ 0.103750] pci 0000:00:1f.1: reg 0x14: [io 0x0000-0x0003]
    [ 0.103760] pci 0000:00:1f.1: reg 0x18: [io 0x0000-0x0007]
    [ 0.103769] pci 0000:00:1f.1: reg 0x1c: [io 0x0000-0x0003]
    [ 0.103778] pci 0000:00:1f.1: reg 0x20: [io 0xf900-0xf90f]
    [ 0.103876] pci 0000:00:1f.2: [8086:27c0] type 00 class 0x01018f
    [ 0.103890] pci 0000:00:1f.2: reg 0x10: [io 0xf800-0xf807]
    [ 0.103899] pci 0000:00:1f.2: reg 0x14: [io 0xf700-0xf703]
    [ 0.103907] pci 0000:00:1f.2: reg 0x18: [io 0xf600-0xf607]
    [ 0.103915] pci 0000:00:1f.2: reg 0x1c: [io 0xf500-0xf503]
    [ 0.103923] pci 0000:00:1f.2: reg 0x20: [io 0xf400-0xf40f]
    [ 0.103932] pci 0000:00:1f.2: reg 0x24: [mem 0xfdffc000-0xfdffc3ff]
    [ 0.103961] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.104042] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
    [ 0.104093] pci 0000:00:1f.3: reg 0x20: [io 0x0500-0x051f]
    [ 0.104236] pci 0000:01:00.0: [1002:7181] type 00 class 0x030000
    [ 0.104251] pci 0000:01:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.104262] pci 0000:01:00.0: reg 0x18: [mem 0xfddf0000-0xfddfffff 64bit]
    [ 0.104270] pci 0000:01:00.0: reg 0x20: [io 0xce00-0xceff]
    [ 0.104283] pci 0000:01:00.0: reg 0x30: [mem 0xfddc0000-0xfdddffff pref]
    [ 0.104314] pci 0000:01:00.0: supports D1 D2
    [ 0.104362] pci 0000:01:00.1: [1002:71a1] type 00 class 0x038000
    [ 0.104373] pci 0000:01:00.1: reg 0x10: [mem 0xfdde0000-0xfddeffff 64bit]
    [ 0.104417] pci 0000:01:00.1: supports D1 D2
    [ 0.104457] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.104466] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.104470] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
    [ 0.104473] pci 0000:00:01.0: bridge window [mem 0xfdd00000-0xfddfffff]
    [ 0.104477] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.104526] pci 0000:02:01.0: [11c1:5811] type 00 class 0x0c0010
    [ 0.104543] pci 0000:02:01.0: reg 0x10: [mem 0xfdeff000-0xfdefffff]
    [ 0.104616] pci 0000:02:01.0: supports D1 D2
    [ 0.104619] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot
    [ 0.104672] pci 0000:02:04.0: [1102:0002] type 00 class 0x040100
    [ 0.104690] pci 0000:02:04.0: reg 0x10: [io 0xdf00-0xdf1f]
    [ 0.104763] pci 0000:02:04.0: supports D1 D2
    [ 0.104806] pci 0000:02:04.1: [1102:7002] type 00 class 0x098000
    [ 0.104822] pci 0000:02:04.1: reg 0x10: [io 0xde00-0xde07]
    [ 0.104895] pci 0000:02:04.1: supports D1 D2
    [ 0.104946] pci 0000:02:05.0: [168c:0013] type 00 class 0x020000
    [ 0.104964] pci 0000:02:05.0: reg 0x10: [mem 0xfdee0000-0xfdeeffff]
    [ 0.105084] pci 0000:02:08.0: [8086:27dc] type 00 class 0x020000
    [ 0.105101] pci 0000:02:08.0: reg 0x10: [mem 0xfdefe000-0xfdefefff]
    [ 0.105112] pci 0000:02:08.0: reg 0x14: [io 0xdd00-0xdd3f]
    [ 0.105176] pci 0000:02:08.0: supports D1 D2
    [ 0.105178] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.105247] pci 0000:00:1e.0: PCI bridge to [bus 02] (subtractive decode)
    [ 0.105252] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
    [ 0.105256] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.105262] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.105264] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xfffffffff] (subtractive decode)
    [ 0.105612] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *7 9 10 11 12 14 15)
    [ 0.105678] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15)
    [ 0.105743] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 7 9 10 11 12 14 15)
    [ 0.105807] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
    [ 0.105870] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 9 10 11 12 14 15)
    [ 0.105934] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
    [ 0.105998] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
    [ 0.106063] ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15)
    [ 0.106250] ACPI: Enabled 2 GPEs in block 00 to 1F
    [ 0.106258] ACPI: \_SB_.PCI0: notify handler is installed
    [ 0.106290] Found 1 acpi root devices
    [ 0.106365] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.106365] vgaarb: loaded
    [ 0.106365] vgaarb: bridge control possible 0000:01:00.0
    [ 0.106365] PCI: Using ACPI for IRQ routing
    [ 0.106365] PCI: pci_cache_line_size set to 64 bytes
    [ 0.106365] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff]
    [ 0.106365] e820: reserve RAM buffer [mem 0x7fedf800-0x7fffffff]
    [ 0.106365] NetLabel: Initializing
    [ 0.106365] NetLabel: domain hash size = 128
    [ 0.106365] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.106365] NetLabel: unlabeled traffic allowed by default
    [ 0.106365] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.106365] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.106365] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.106689] Switched to clocksource hpet
    [ 0.109999] pnp: PnP ACPI init
    [ 0.109999] ACPI: bus type PNP registered
    [ 0.113399] system 00:00: [io 0x04d0-0x04d1] has been reserved
    [ 0.113403] system 00:00: [io 0x0800-0x087f] has been reserved
    [ 0.113406] system 00:00: [io 0x0294-0x0297] has been reserved
    [ 0.113408] system 00:00: [io 0x0880-0x088f] has been reserved
    [ 0.113413] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.113426] pnp 00:01: [dma 4]
    [ 0.113459] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.113547] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.113597] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.113626] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.113664] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.113790] pnp 00:06: Plug and Play ACPI device, IDs PNP0f13 (active)
    [ 0.113848] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
    [ 0.113911] system 00:08: [io 0x0400-0x04bf] has been reserved
    [ 0.113915] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.113958] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.114177] system 00:0a: [mem 0xf0000000-0xf3ffffff] has been reserved
    [ 0.114182] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.114356] system 00:0b: [mem 0x000cf400-0x000cffff] has been reserved
    [ 0.114359] system 00:0b: [mem 0x000f0000-0x000f7fff] could not be reserved
    [ 0.114362] system 00:0b: [mem 0x000f8000-0x000fbfff] could not be reserved
    [ 0.114365] system 00:0b: [mem 0x000fc000-0x000fffff] could not be reserved
    [ 0.114368] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved
    [ 0.114371] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved
    [ 0.114374] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.114377] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved
    [ 0.114380] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.114382] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.114385] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved
    [ 0.114388] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved
    [ 0.114390] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved
    [ 0.114394] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.114404] pnp: PnP ACPI: found 12 devices
    [ 0.114405] ACPI: bus type PNP unregistered
    [ 0.120198] pci 0000:00:01.0: PCI bridge to [bus 01]
    [ 0.120198] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
    [ 0.120198] pci 0000:00:01.0: bridge window [mem 0xfdd00000-0xfddfffff]
    [ 0.120198] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.120198] pci 0000:00:1e.0: PCI bridge to [bus 02]
    [ 0.120198] pci 0000:00:1e.0: bridge window [io 0xd000-0xdfff]
    [ 0.120198] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.120198] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
    [ 0.120198] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
    [ 0.120198] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
    [ 0.120198] pci_bus 0000:01: resource 1 [mem 0xfdd00000-0xfddfffff]
    [ 0.120198] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.120198] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
    [ 0.120198] pci_bus 0000:02: resource 1 [mem 0xfde00000-0xfdefffff]
    [ 0.120198] pci_bus 0000:02: resource 4 [io 0x0000-0xffff]
    [ 0.120198] pci_bus 0000:02: resource 5 [mem 0x00000000-0xfffffffff]
    [ 0.120198] NET: Registered protocol family 2
    [ 0.120198] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.120198] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
    [ 0.120198] TCP: Hash tables configured (established 16384 bind 16384)
    [ 0.120198] TCP: reno registered
    [ 0.120198] UDP hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.120198] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
    [ 0.120198] NET: Registered protocol family 1
    [ 0.120198] pci 0000:01:00.0: Boot video device
    [ 0.120198] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
    [ 0.120198] PCI: CLS 32 bytes, default 64
    [ 0.120198] Unpacking initramfs...
    [ 0.191296] Freeing initrd memory: 3084K (ffff8800379ea000 - ffff880037ced000)
    [ 0.191480] Scanning for low memory corruption every 60 seconds
    [ 0.191882] audit: initializing netlink socket (disabled)
    [ 0.191902] type=2000 audit(1396428835.189:1): initialized
    [ 0.206560] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.208164] zbud: loaded
    [ 0.208353] VFS: Disk quotas dquot_6.5.2
    [ 0.208404] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.208606] msgmni has been set to 4004
    [ 0.208673] Key type big_key registered
    [ 0.208929] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.208971] io scheduler noop registered
    [ 0.208973] io scheduler deadline registered
    [ 0.209007] io scheduler cfq registered (default)
    [ 0.209208] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.209282] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.209302] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.209360] vesafb: mode is 1400x1050x32, linelength=5632, pages=0
    [ 0.209362] vesafb: scrolling: redraw
    [ 0.209364] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
    [ 0.209895] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc90004400000, using 5824k, total 5824k
    [ 0.265490] Console: switching to colour frame buffer device 175x65
    [ 0.320013] fb0: VESA VGA frame buffer device
    [ 0.320013] intel_idle: does not run on family 6 model 15
    [ 0.320013] GHES: HEST is not enabled!
    [ 0.320771] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.321201] Linux agpgart interface v0.103
    [ 0.321270] rtc_cmos 00:03: RTC can wake from S4
    [ 0.321402] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 0.321430] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.321540] drop_monitor: Initializing network drop monitor service
    [ 0.321607] TCP: cubic registered
    [ 0.321718] NET: Registered protocol family 10
    [ 0.321912] NET: Registered protocol family 17
    [ 0.321924] Key type dns_resolver registered
    [ 0.322165] registered taskstats version 1
    [ 0.322582] Magic number: 10:872:926
    [ 0.322659] rtc_cmos 00:03: setting system clock to 2014-04-02 08:54:05 UTC (1396428845)
    [ 0.322694] PM: Hibernation image not present or could not be loaded.
    [ 0.324137] Freeing unused kernel memory: 1124K (ffffffff818d3000 - ffffffff819ec000)
    [ 0.324139] Write protecting the kernel read-only data: 8192k
    [ 0.326967] Freeing unused kernel memory: 860K (ffff880001529000 - ffff880001600000)
    [ 0.327354] Freeing unused kernel memory: 372K (ffff8800017a3000 - ffff880001800000)
    [ 0.335950] random: systemd-tmpfile urandom read with 1 bits of entropy available
    [ 0.337560] systemd-udevd[46]: starting version 212
    [ 0.357062] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
    [ 0.360689] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.360743] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.364815] ACPI: bus type USB registered
    [ 0.364858] usbcore: registered new interface driver usbfs
    [ 0.364871] usbcore: registered new interface driver hub
    [ 0.367300] usbcore: registered new device driver usb
    [ 0.367497] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.367497] uhci_hcd: USB Universal Host Controller Interface driver
    [ 0.367497] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 0.369227] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
    [ 0.369272] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ff00
    [ 0.370097] hub 1-0:1.0: USB hub found
    [ 0.370108] hub 1-0:1.0: 2 ports detected
    [ 0.370356] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 0.370364] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
    [ 0.370398] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fe00
    [ 0.370561] hub 2-0:1.0: USB hub found
    [ 0.370570] hub 2-0:1.0: 2 ports detected
    [ 0.370923] ehci-pci: EHCI PCI platform driver
    [ 0.371254] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 0.371263] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
    [ 0.371299] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fd00
    [ 0.371479] hub 3-0:1.0: USB hub found
    [ 0.371489] hub 3-0:1.0: 2 ports detected
    [ 0.371685] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 0.371695] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
    [ 0.371731] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fc00
    [ 0.371759] SCSI subsystem initialized
    [ 0.372294] hub 4-0:1.0: USB hub found
    [ 0.372721] hub 4-0:1.0: 2 ports detected
    [ 0.373567] ehci-pci 0000:00:1d.7: EHCI Host Controller
    [ 0.373575] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 5
    [ 0.380063] ehci-pci 0000:00:1d.7: cache line size of 32 is not supported
    [ 0.380074] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfdfff000
    [ 0.380372] libata version 3.00 loaded.
    [ 0.392071] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 0.392288] hub 5-0:1.0: USB hub found
    [ 0.392298] hub 5-0:1.0: 8 ports detected
    [ 0.413670] hub 1-0:1.0: USB hub found
    [ 0.413685] hub 1-0:1.0: 2 ports detected
    [ 0.418065] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.428408] firewire_ohci 0000:02:01.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
    [ 0.444932] hub 2-0:1.0: USB hub found
    [ 0.444946] hub 2-0:1.0: 2 ports detected
    [ 0.475276] hub 3-0:1.0: USB hub found
    [ 0.475295] hub 3-0:1.0: 2 ports detected
    [ 0.498283] hub 4-0:1.0: USB hub found
    [ 0.498296] hub 4-0:1.0: 2 ports detected
    [ 0.498418] ata_piix 0000:00:1f.1: version 2.13
    [ 0.499273] scsi0 : ata_piix
    [ 0.499357] scsi1 : ata_piix
    [ 0.499402] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
    [ 0.499404] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
    [ 0.499515] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
    [ 0.499556] ata2: port disabled--ignoring
    [ 0.500252] scsi2 : ata_piix
    [ 0.500325] scsi3 : ata_piix
    [ 0.500368] ata3: SATA max UDMA/133 cmd 0xf800 ctl 0xf700 bmdma 0xf400 irq 19
    [ 0.500371] ata4: SATA max UDMA/133 cmd 0xf600 ctl 0xf500 bmdma 0xf408 irq 19
    [ 0.699056] ata4.01: NODEV after polling detection
    [ 0.705789] ata4.00: ATAPI: HL-DT-STDVDRRW GSA-H30L, S755, max UDMA/33
    [ 0.705879] ata1.00: ATA-7: Hitachi HDT725032VLAT80, V54OA42A, max UDMA/133
    [ 0.705882] ata1.00: 625142448 sectors, multi 16: LBA48
    [ 0.705886] ata1.00: limited to UDMA/33 due to 40-wire cable
    [ 0.718854] ata4.00: configured for UDMA/33
    [ 0.721647] ata1.00: configured for UDMA/33
    [ 0.721797] scsi 0:0:0:0: Direct-Access ATA Hitachi HDT72503 V54O PQ: 0 ANSI: 5
    [ 0.725607] ata3.00: ATA-8: SAMSUNG HD320KJ, CP100-10, max UDMA7
    [ 0.725612] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
    [ 0.734331] ata3.00: configured for UDMA/133
    [ 0.734447] scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD320KJ CP10 PQ: 0 ANSI: 5
    [ 0.736470] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRRW GSA-H30L S755 PQ: 0 ANSI: 5
    [ 0.739885] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
    [ 0.739947] sd 0:0:0:0: [sda] Write Protect is off
    [ 0.739950] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 0.739977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.740339] sd 2:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
    [ 0.740397] sd 2:0:0:0: [sdb] Write Protect is off
    [ 0.740400] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 0.740426] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.743908] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 0.743912] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 0.744145] sr 3:0:0:0: Attached scsi CD-ROM sr0
    [ 0.748725] sdb: sdb1 sdb2
    [ 0.749036] sd 2:0:0:0: [sdb] Attached SCSI disk
    [ 0.752217] usb 5-6: new high-speed USB device number 2 using ehci-pci
    [ 0.778689] sda: sda1 sda2 sda3 sda4
    [ 0.779129] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 0.929217] firewire_core 0000:02:01.0: created device fw0: GUID 0011d800013adf24, S400
    [ 1.006684] usb 5-7: new high-speed USB device number 3 using ehci-pci
    [ 1.173252] usb-storage 5-7:1.0: USB Mass Storage device detected
    [ 1.173332] scsi4 : usb-storage 5-7:1.0
    [ 1.173427] usbcore: registered new interface driver usb-storage
    [ 1.197356] tsc: Refined TSC clocksource calibration: 2133.939 MHz
    [ 1.616813] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
    [ 1.624951] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
    [ 1.920203] random: nonblocking pool is initialized
    [ 2.247183] Switched to clocksource tsc
    [ 2.253827] scsi 4:0:0:0: Direct-Access Generic- Compact Flash 1.00 PQ: 0 ANSI: 0 CCS
    [ 2.260322] scsi 4:0:0:1: Direct-Access Generic- SM/xD-Picture 1.00 PQ: 0 ANSI: 0 CCS
    [ 2.266946] scsi 4:0:0:2: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0 CCS
    [ 2.273571] scsi 4:0:0:3: Direct-Access Generic- MS/MS-Pro 1.00 PQ: 0 ANSI: 0 CCS
    [ 2.280559] sd 4:0:0:0: [sdc] Attached SCSI removable disk
    [ 2.281310] sd 4:0:0:1: [sdd] Attached SCSI removable disk
    [ 2.282059] sd 4:0:0:2: [sde] Attached SCSI removable disk
    [ 2.282809] sd 4:0:0:3: [sdf] Attached SCSI removable disk
    [ 2.498874] systemd[1]: systemd 212 running in system mode. (+PAM -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ +SECCOMP -APPARMOR)
    [ 2.499029] systemd[1]: Detected architecture 'x86-64'.
    [ 2.499095] systemd[1]: No hostname configured.
    [ 2.499100] systemd[1]: Set hostname to <localhost>.
    [ 3.019084] systemd[1]: Configuration file /etc/systemd/system/netctl@ethernet\x2dstatic.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
    [ 3.052564] systemd[1]: Configuration file /etc/systemd/system/netctl@my\x2dnetwork.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
    [ 3.168175] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 3.168523] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 3.168587] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 3.168600] systemd[1]: Expecting device sys-subsystem-net-devices-enp2s8.device...
    [ 3.168617] systemd[1]: Starting Remote File Systems.
    [ 3.168629] systemd[1]: Reached target Remote File Systems.
    [ 3.168639] systemd[1]: Expecting device sys-subsystem-net-devices-wlp2s5.device...
    [ 3.168655] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 3.168691] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 3.168701] systemd[1]: Starting Paths.
    [ 3.168712] systemd[1]: Reached target Paths.
    [ 3.168722] systemd[1]: Starting Encrypted Volumes.
    [ 3.168732] systemd[1]: Reached target Encrypted Volumes.
    [ 3.168756] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
    [ 3.168851] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 3.168865] systemd[1]: Expecting device dev-sda4.device...
    [ 3.168877] systemd[1]: Expecting device dev-disk-by\x2duuid-8e743759\x2dc6f4\x2d4e8f\x2dae25\x2d2c24a8cba618.device...
    [ 3.168890] systemd[1]: Expecting device dev-disk-by\x2duuid-c96171f5\x2d9704\x2d4abf\x2d84ae\x2d2c4f78252a60.device...
    [ 3.168900] systemd[1]: Expecting device dev-disk-by\x2duuid-12EC23D6EC23B341.device...
    [ 3.168911] systemd[1]: Starting Root Slice.
    [ 3.175997] systemd[1]: Created slice Root Slice.
    [ 3.176010] systemd[1]: Starting Delayed Shutdown Socket.
    [ 3.176047] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 3.176058] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 3.176087] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 3.176098] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 3.176119] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 3.176133] systemd[1]: Starting udev Kernel Socket.
    [ 3.176155] systemd[1]: Listening on udev Kernel Socket.
    [ 3.176169] systemd[1]: Starting udev Control Socket.
    [ 3.176193] systemd[1]: Listening on udev Control Socket.
    [ 3.176203] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 3.176232] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 3.176243] systemd[1]: Starting User and Session Slice.
    [ 3.176438] systemd[1]: Created slice User and Session Slice.
    [ 3.176452] systemd[1]: Starting Journal Socket.
    [ 3.176501] systemd[1]: Listening on Journal Socket.
    [ 3.176518] systemd[1]: Starting System Slice.
    [ 3.176712] systemd[1]: Created slice System Slice.
    [ 3.176728] systemd[1]: Started File System Check on Root Device.
    [ 3.176738] systemd[1]: Starting system-systemd\x2dfsck.slice.
    [ 3.176940] systemd[1]: Created slice system-systemd\x2dfsck.slice.
    [ 3.176954] systemd[1]: Starting Remount Root and Kernel File Systems...
    [ 3.212380] systemd[1]: Started Load Kernel Modules.
    [ 3.252481] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 3.253015] systemd[1]: Starting udev Coldplug all Devices...
    [ 3.253553] systemd[1]: Mounted FUSE Control File System.
    [ 3.253577] systemd[1]: Mounting Configuration File System...
    [ 3.254197] systemd[1]: Starting Setup Virtual Console...
    [ 3.254782] systemd[1]: Mounting Debug File System...
    [ 3.255307] systemd[1]: Mounting Huge Pages File System...
    [ 3.285128] systemd[1]: Starting Apply Kernel Variables...
    [ 3.285663] systemd[1]: Starting system-netctl.slice.
    [ 3.285916] systemd[1]: Created slice system-netctl.slice.
    [ 3.285940] systemd[1]: Starting system-getty.slice.
    [ 3.286240] systemd[1]: Created slice system-getty.slice.
    [ 3.286797] systemd[1]: Started Set Up Additional Binary Formats.
    [ 3.286822] systemd[1]: Mounting POSIX Message Queue File System...
    [ 3.287292] systemd[1]: Starting Journal Service...
    [ 3.287880] systemd[1]: Started Journal Service.
    [ 4.510133] EXT4-fs (sda2): re-mounted. Opts: data=ordered
    [ 4.568872] systemd-udevd[136]: starting version 212
    [ 5.479614] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
    [ 5.479621] ACPI: Power Button [PWRB]
    [ 5.479693] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 5.479697] ACPI: Power Button [PWRF]
    [ 5.490126] thermal LNXTHERM:00: registered as thermal_zone0
    [ 5.490129] ACPI: Thermal Zone [THRM] (19 C)
    [ 5.629665] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PM2S 1 (20131115/utaddress-251)
    [ 5.629673] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PM1K 2 (20131115/utaddress-251)
    [ 5.629677] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \GPE1 3 (20131115/utaddress-251)
    [ 5.629682] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 5.629685] ACPI Warning: 0x00000000000004b0-0x00000000000004bf SystemIO conflicts with Region \GPO2 1 (20131115/utaddress-251)
    [ 5.629689] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 5.629691] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \GPIV 1 (20131115/utaddress-251)
    [ 5.629695] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \GPO_ 2 (20131115/utaddress-251)
    [ 5.629699] ACPI Warning: 0x0000000000000480-0x00000000000004af SystemIO conflicts with Region \PALD 3 (20131115/utaddress-251)
    [ 5.629703] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 5.629705] lpc_ich: Resource conflict(s) found affecting gpio_ich
    [ 5.639853] leds_ss4200: no LED devices found
    [ 5.687416] ACPI: Fan [FAN] (on)
    [ 5.708079] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 5.931908] cfg80211: Calling CRDA to update world regulatory domain
    [ 6.109750] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
    [ 6.109754] e100: Copyright(c) 1999-2006 Intel Corporation
    [ 6.133562] e100 0000:02:08.0 eth0: addr 0xfdefe000, irq 20, MAC addr 00:1a:92:de:71:43
    [ 6.410441] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt
    [ 6.599698] gameport gameport0: EMU10K1 is pci0000:02:04.1/gameport0, io 0xde00, speed 980kHz
    [ 6.659464] [drm] Initialized drm 1.1.0 20060810
    [ 6.722900] input: PC Speaker as /devices/platform/pcspkr/input/input4
    [ 6.926377] iTCO_vendor_support: vendor-support=0
    [ 6.963443] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
    [ 6.963473] iTCO_wdt: Found a ICH7DH TCO device (Version=2, TCOBASE=0x0460)
    [ 6.963581] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 7.184227] Adding 4286784k swap on /dev/sda4. Priority:-1 extents:1 across:4286784k FS
    [ 7.195727] microcode: CPU0 sig=0x6f6, pf=0x1, revision=0xc6
    [ 7.263090] rtl8192cu: Chip version 0x11
    [ 7.334816] ath5k 0000:02:05.0: registered as 'phy1'
    [ 7.352471] rtl8192cu: MAC address: 80:1f:02:af:89:eb
    [ 7.352477] rtl8192cu: Board Type 0
    [ 7.352718] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
    [ 7.352752] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
    [ 7.352808] usbcore: registered new interface driver rtl8192cu
    [ 7.445824] [drm] radeon kernel modesetting enabled.
    [ 7.445878] checking generic (e0000000 5b0000) vs hw (e0000000 10000000)
    [ 7.445880] fb: conflicting fb hw usage radeondrmfb vs VESA VGA - removing generic driver
    [ 7.316873] systemd-udevd[150]: renamed network interface eth0 to enp2s8
    [ 7.445900] Console: switching
    [ 7.445902] to colour dummy device 80x25
    [ 7.446670] [drm] initializing kernel modesetting (RV515 0x1002:0x7181 0x1462:0x0400).
    [ 7.446689] [drm] register mmio base: 0xFDDF0000
    [ 7.446691] [drm] register mmio size: 65536
    [ 7.446807] ATOM BIOS: 113
    [ 7.446821] [drm] Generation 2 PCI interface, using max accessible memory
    [ 7.446827] radeon 0000:01:00.0: VRAM: 512M 0x0000000000000000 - 0x000000001FFFFFFF (512M used)
    [ 7.446830] radeon 0000:01:00.0: GTT: 512M 0x0000000020000000 - 0x000000003FFFFFFF
    [ 7.446845] [drm] Detected VRAM RAM=512M, BAR=256M
    [ 7.446847] [drm] RAM width 128bits DDR
    [ 7.446916] [TTM] Zone kernel: Available graphics memory: 1026428 kiB
    [ 7.446918] [TTM] Initializing pool allocator
    [ 7.446923] [TTM] Initializing DMA pool allocator
    [ 7.446942] [drm] radeon: 512M of VRAM memory ready
    [ 7.446944] [drm] radeon: 512M of GTT memory ready.
    [ 7.446965] [drm] GART: num cpu pages 131072, num gpu pages 131072
    [ 7.458262] [drm] radeon: 1 quad pipes, 1 z pipes initialized.
    [ 7.459147] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
    [ 7.459171] radeon 0000:01:00.0: WB enabled
    [ 7.459176] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr 0x0000000020000000 and cpu addr 0xffff88007bb31000
    [ 7.459179] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 7.459180] [drm] Driver supports precise vblank timestamp query.
    [ 7.459192] [drm] radeon: irq initialized.
    [ 7.459208] [drm] Loading R500 Microcode
    [ 7.476935] platform microcode: Direct firmware load failed with error -2
    [ 7.476939] platform microcode: Falling back to user helper
    [ 7.477387] microcode: CPU1 sig=0x6f6, pf=0x1, revision=0xc6
    [ 7.477402] platform microcode: Direct firmware load failed with error -2
    [ 7.477405] platform microcode: Falling back to user helper
    [ 7.477982] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 7.503453] [drm] radeon: ring at 0x0000000020001000
    [ 7.503490] [drm] ring test succeeded in 6 usecs
    [ 7.503671] [drm] ib test succeeded in 0 usecs
    [ 7.503948] [drm] Radeon Display Connectors
    [ 7.503950] [drm] Connector 0:
    [ 7.503951] [drm] DVI-I-1
    [ 7.503953] [drm] HPD2
    [ 7.503955] [drm] DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
    [ 7.503957] [drm] Encoders:
    [ 7.503958] [drm] CRT1: INTERNAL_KLDSCP_DAC1
    [ 7.503960] [drm] DFP3: INTERNAL_LVTM1
    [ 7.503961] [drm] Connector 1:
    [ 7.503963] [drm] SVIDEO-1
    [ 7.503964] [drm] Encoders:
    [ 7.503965] [drm] TV1: INTERNAL_KLDSCP_DAC2
    [ 7.503967] [drm] Connector 2:
    [ 7.503968] [drm] DVI-I-2
    [ 7.503969] [drm] HPD1
    [ 7.503971] [drm] DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
    [ 7.503973] [drm] Encoders:
    [ 7.503974] [drm] CRT2: INTERNAL_KLDSCP_DAC2
    [ 7.503976] [drm] DFP1: INTERNAL_KLDSCP_TMDS1
    [ 7.583351] [drm] fb mappable at 0xE00C0000
    [ 7.583351] [drm] vram apper at 0xE0000000
    [ 7.583351] [drm] size 7258112
    [ 7.583351] [drm] fb depth is 24
    [ 7.583351] [drm] pitch is 6912
    [ 7.583719] fbcon: radeondrmfb (fb0) is primary device
    [ 7.600235] Console: switching to colour frame buffer device 210x65
    [ 7.605874] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
    [ 7.605877] radeon 0000:01:00.0: registered panic notifier
    [ 7.605883] [drm] Initialized radeon 2.36.0 20080528 for 0000:01:00.0 on minor 0
    [ 7.625781] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
    [ 7.626479] rtlwifi: wireless switch is on
    [ 7.642639] fuse init (API version 7.22)
    [ 7.647140] ath: EEPROM regdomain: 0x0
    [ 7.647144] ath: EEPROM indicates default country code should be used
    [ 7.647146] ath: doing EEPROM country->regdmn map search
    [ 7.647149] ath: country maps to regdmn code: 0x3a
    [ 7.647151] ath: Country alpha2 being used: US
    [ 7.647153] ath: Regpair used: 0x3a
    [ 7.647274] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
    [ 7.647537] ath5k: phy1: Atheros AR5212 chip found (MAC: 0x56, PHY: 0x41)
    [ 7.647540] ath5k: phy1: RF5111 5GHz radio found (0x17)
    [ 7.647543] ath5k: phy1: RF2111 2GHz radio found (0x23)
    [ 7.709874] systemd-udevd[143]: renamed network interface wlan1 to wlp2s5
    [ 8.136233] systemd-udevd[141]: renamed network interface wlan0 to wlp0s29f7u6
    [ 8.322562] coretemp coretemp.0: Using relative temperature scale!
    [ 8.322706] coretemp coretemp.0: Using relative temperature scale!
    [ 8.594743] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input5
    [ 8.638575] mousedev: PS/2 mouse device common for all mice
    [ 9.284691] EXT4-fs (sda3): mounting ext3 file system using the ext4 subsystem
    [ 9.328865] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 10.357627] IPv6: ADDRCONF(NETDEV_UP): enp2s8: link is not ready
    [ 10.363499] e100 0000:02:08.0 enp2s8: NIC Link is Up 100 Mbps Full Duplex
    [ 10.363772] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s8: link becomes ready
    [ 10.865860] systemd-journald[119]: Received request to flush runtime journal from PID 1
    [ 11.002834] rtl8192cu: MAC auto ON okay!
    [ 11.035475] rtl8192cu: Tx queue select: 0x05
    [ 11.407281] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 12.592937] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 12.617024] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 12.654273] wlp0s29f7u6: authenticated
    [ 12.659239] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 12.663526] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 12.663558] wlp0s29f7u6: associated
    [ 12.663598] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 216.768500] perf samples too long (2503 > 2500), lowering kernel.perf_event_max_sample_rate to 50100
    [ 295.526133] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 295.538508] cfg80211: Calling CRDA for country: US
    [ 295.779488] rtl8192cu: MAC auto ON okay!
    [ 295.813132] rtl8192cu: Tx queue select: 0x05
    [ 296.188680] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 297.158587] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 297.171430] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 297.181575] wlp0s29f7u6: authenticated
    [ 297.185043] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 297.198798] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 297.198839] wlp0s29f7u6: associated
    [ 297.198885] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 466.957760] perf samples too long (4993 > 4990), lowering kernel.perf_event_max_sample_rate to 25200
    [ 653.237523] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 653.252189] cfg80211: Calling CRDA for country: GB
    [ 653.492515] rtl8192cu: MAC auto ON okay!
    [ 653.526155] rtl8192cu: Tx queue select: 0x05
    [ 653.902071] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 654.830321] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 654.843456] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 654.863972] wlp0s29f7u6: authenticated
    [ 654.867473] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 654.879214] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 654.879258] wlp0s29f7u6: associated
    [ 654.879319] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 845.720733] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 845.733072] cfg80211: Calling CRDA to update world regulatory domain
    [ 845.972288] rtl8192cu: MAC auto ON okay!
    [ 846.005180] rtl8192cu: Tx queue select: 0x05
    [ 846.376969] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 847.303644] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 847.316223] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 847.341107] wlp0s29f7u6: authenticated
    [ 847.345443] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 847.369345] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 847.369380] wlp0s29f7u6: associated
    [ 847.369422] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 1165.243225] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 1165.255458] cfg80211: Calling CRDA for country: GB
    [ 1165.501950] rtl8192cu: MAC auto ON okay!
    [ 1165.534590] rtl8192cu: Tx queue select: 0x05
    [ 1165.906506] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 1166.922571] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 1166.935133] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 1166.962884] wlp0s29f7u6: authenticated
    [ 1166.963550] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 1166.969384] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 1166.969418] wlp0s29f7u6: associated
    [ 1166.969455] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 1317.334883] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 1317.347568] cfg80211: Calling CRDA to update world regulatory domain
    [ 1317.593153] rtl8192cu: MAC auto ON okay!
    [ 1317.625922] rtl8192cu: Tx queue select: 0x05
    [ 1318.002339] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 1318.943694] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 1318.959587] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 1318.961335] wlp0s29f7u6: authenticated
    [ 1318.965144] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 1318.988340] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 1318.988376] wlp0s29f7u6: associated
    [ 1318.988421] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 1469.086853] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 1469.099248] cfg80211: Calling CRDA to update world regulatory domain
    [ 1469.337346] rtl8192cu: MAC auto ON okay!
    [ 1469.370119] rtl8192cu: Tx queue select: 0x05
    [ 1469.742158] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 1470.673984] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 1470.686540] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 1470.691410] wlp0s29f7u6: authenticated
    [ 1470.693241] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 1470.702651] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 1470.702687] wlp0s29f7u6: associated
    [ 1470.702728] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 1680.753182] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 1680.765752] cfg80211: Calling CRDA for country: GB
    [ 1680.998495] rtl8192cu: MAC auto ON okay!
    [ 1681.031255] rtl8192cu: Tx queue select: 0x05
    [ 1681.406799] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 1682.318347] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 1682.330930] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 1682.342673] wlp0s29f7u6: authenticated
    [ 1682.343689] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 1682.350924] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 1682.350956] wlp0s29f7u6: associated
    [ 1682.350994] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 2206.980860] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 2206.993170] cfg80211: Calling CRDA to update world regulatory domain
    [ 2207.227511] rtl8192cu: MAC auto ON okay!
    [ 2207.260157] rtl8192cu: Tx queue select: 0x05
    [ 2207.631823] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 2208.565086] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 2208.577695] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 2208.585581] wlp0s29f7u6: authenticated
    [ 2208.587355] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 2208.616071] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 2208.616112] wlp0s29f7u6: associated
    [ 2208.616155] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 2504.014135] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 2504.026462] cfg80211: Calling CRDA to update world regulatory domain
    [ 2504.273688] rtl8192cu: MAC auto ON okay!
    [ 2504.309828] rtl8192cu: Tx queue select: 0x05
    [ 2504.702760] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 2505.627571] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 2505.640510] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 2505.649754] wlp0s29f7u6: authenticated
    [ 2505.650508] wlp0s29f7u6: associate with 2c:39:96:b3:ba:40 (try 1/3)
    [ 2505.680782] wlp0s29f7u6: RX AssocResp from 2c:39:96:b3:ba:40 (capab=0x431 status=0 aid=44)
    [ 2505.680831] wlp0s29f7u6: associated
    [ 2505.680887] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s29f7u6: link becomes ready
    [ 2948.553142] wlp0s29f7u6: deauthenticating from 2c:39:96:b3:ba:40 by local choice (reason=3)
    [ 2948.565823] cfg80211: Calling CRDA for country: GB
    [ 2948.814051] rtl8192cu: MAC auto ON okay!
    [ 2948.846690] rtl8192cu: Tx queue select: 0x05
    [ 2949.220485] IPv6: ADDRCONF(NETDEV_UP): wlp0s29f7u6: link is not ready
    [ 2950.173570] wlp0s29f7u6: authenticate with 2c:39:96:b3:ba:40
    [ 2950.186113] wlp0s29f7u6: send auth to 2c:39:96:b3:ba:40 (try 1/3)
    [ 2950.190241] wlp0s29f7u6: authenticated
    If there is anything else I can provide that may help please ask, this has been driving me mad for days now!

    Looks like a driver bug. You could try multiple things, as a start:
    - switch channel
    - toggle encryption
    - different usb port

  • Windows 2008 R2, Network drops even after rebuild, Please help to diagnose

    Hi there,
    I've had an issue for a while now and I have been working through it and I'm getting lost and starting to go around in circles.
    I have just rebuild up a Server 2008 R2 x64
    Configuration is
    Server: HP Prolient ML330 G6 Quad core xeon 24GB ram (between 2-3 Years Old)
    HDD: Raid1 500GB
    ip: 192.168.1.253
    su: 255,255,255.0
    gw: 192.168.1.1
    dns 1: 192.168.1.253 (Was 127.0.0.1) please read on!!!
    dns 2: empty
    Roles and SW: AD DC, DNS, DHCP and Exchange Server (in 1 box)
    My original issue was network dropping out every few weeks, progressively got worse to being daily. Restarts would fix it, tho would disconnect after hours or a day or 2.
    Issues would be that during a network outage, I cannot connect workstations to domain, no network shares. Internet was dead, and a heap of Event ID errors
    Server rebuild went well, It's a 2008 R2 setup and it runs basically everything in 1 server 2008 R2.. I know its not ideal but it's what they had setup previously.
    So After rebuild I was using it for hours and hours and configuring, adding, cleaning, updating. All was good.
    I was restoring of some emails and system was loaded medium to high for a while.
    I went home thinking all was good and might connect via VPN and do some work and monitor it all, The vpn disconnected after a few minutes.
    I called their office and asked is all normal?
    They said network shares and emails have stopped. I confirmed this as the network would do the same thing it was doing before the rebuild.
    So I restarted the server and Internet/Network drops within minutes of being restarted. tried many things to solve this..
    hours later I installed known hotfixes, updated drivers, and tried so many other things to try and solve this...
    I had heaps of Event ID errors before the rebuild, and trying to ping anyone was resulting in General Errors, and cannot ping basically
    After the rebuild it has same sorts of event id errors. I had same general errors when trying to ping.
    In the end at 2am 2 weeks ago, I finally got it running smoother..
    I did 2 things which have made the network last longer then few minutes...
    1. Disabled the Network Port 1 and Enabled the 2nd Port. (Both On board FYI)
    2. Changed DNS in the TCPIPv4 from 127.0.0.1 to (192.168.1.253 (Servers IP))
    Since this change, I no longer get event ID errors.
    When network stops working the network icon stays normal.
    And network is lasting days rather then hours.
    Things I've spoken to others about,
    - 127.0.0.1 and changing to 192.168.1.253 these 2 are basically the same both being loopback to server. They both point to itself..
    - The fact the problems reappeared after a rebuild points towards hardware
    - I think the summer heat might have cooked the NIC :p as same day the server crapped itself my clients home wifi setup also died. The range extender died! weird coincidence
    - So I am seriously thinking it cannot be the DNS IP Configuration setting, I know that running all roles on a single server is hard for a server. But I find it hard to believe it was the DNS which caused this error
    I have continued to work on this issue through the weeks.,
    The following information is newest
    28th March,
    After 2 days of sweet operation.. IE Just after the switch to 2nd port.
    The server's network went down.., 
    I can ping only 127.0.0.1 or 192.168.1.253 ok
    but ping gateway or workstations times out.
    Netstat shows heaps of ipv6 and very few ipv4 addresses
    I restarted the server, applying computer settings sat there for a while..
    dunno if it was coincidence or not but unplugging the Gateway and replugging it made the CTRL-ALT-DEL come up right away.
    after boot everything has been ok for 14 hours now...
    Now the Network Ports (2 of them are on the server, most likely sharing controller)
    Please take a look at my ping/netstat and please make any comments.
    ----- Ping.txt -----
    Microsoft Windows [Version 6.1.7601]
    Copyright © 2009 Microsoft Corporation. All rights reserved.
    C:\Users\Administrator>ping 192.168.1.1
    Pinging 192.168.1.1 with 32 bytes of data:
    Request timed out.
    Request timed out.
    Request timed out.
    Request timed out.
    Ping statistics for 192.168.1.1:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
    C:\Users\Administrator>ping 192.168.1.253
    Pinging 192.168.1.253 with 32 bytes of data:
    Reply from 192.168.1.253: bytes=32 time<1ms TTL=128
    Reply from 192.168.1.253: bytes=32 time<1ms TTL=128
    Reply from 192.168.1.253: bytes=32 time<1ms TTL=128
    Reply from 192.168.1.253: bytes=32 time<1ms TTL=128
    Ping statistics for 192.168.1.253:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
    C:\Users\Administrator>ping 127.0.0.1
    Pinging 127.0.0.1 with 32 bytes of data:
    Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
    Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
    Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
    Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
    Ping statistics for 127.0.0.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
    Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
    C:\Users\Administrator>ping google.com
    Ping request could not find host google.com. Please check the name and try again
    C:\Users\Administrator>netstat
    Active Connections
    Proto Local Address Foreign Address State
    TCP 192.168.1.125:6008 192.168.1.118:49683 ESTABLISHED
    TCP 192.168.1.253:6008 192.168.1.120:55103 ESTABLISHED
    TCP 192.168.1.253:6008 192.168.1.121:49703 ESTABLISHED
    TCP 192.168.1.253:6674 WORK-SERVER:19928 TIME_WAIT
    TCP 192.168.1.253:19928 WORK-SERVER:6674 TIME_WAIT
    TCP [::1]:389 WORK-SERVER:6012 ESTABLISHED
    TCP [::1]:389 WORK-SERVER:6013 ESTABLISHED
    TCP [::1]:389 WORK-SERVER:36939 ESTABLISHED
    TCP [::1]:6012 WORK-SERVER:ldap ESTABLISHED
    TCP [::1]:6013 WORK-SERVER:ldap ESTABLISHED
    TCP [::1]:36939 WORK-SERVER:ldap ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:19932 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:32574 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:35314 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:35353 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:56321 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:135 WORK-SERVER:64583 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6684 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6685 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6686 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6687 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6689 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6692 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6694 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6712 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:6765 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:17256 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:17327 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:19074 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:19075 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:19077 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:19896 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:19902 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:24754 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:36936 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:36944 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:36946 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:41165 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:56317 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:56319 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59239 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59243 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59244 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59245 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59258 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59262 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59263 ESTABLISHED
    TCP [fe80::9142:b19d:a6d0:d31d%14]:389 WORK-SERVER:59327
    A HEAP MORE IPv6 but msg too long
    I have noticed currently using the Cisco Gigabit switch the network will last 24-48 hours.
    3th April
    I have tested a 10/100 16port netgear and the network lasted for 5+ Days.
    8th April
    I noticed network and sharing centre icon has no exclaimation mark looked normal.. so on server I tried to open google website.
    Nothing....
    I pinged loopback. was ok
    Ping the modem and not ok.
    So I restarted the adsl modem. Within a minute server resumed internet..
    I am unsure if the router caused this dropout. And my thinking spans now using a maximum speed of 100mbps it has taken 5 days to drop. WHY is this?
    Either the modem is causing this. Or its the server nic running at only 100mbps
    Does it make any sence?
    Can a nic on server cause a drop only to restart the gateway to make it startup again.
    From my post do you think the port on the gateway is flaky? As you said maybe too much for it to handle.
    The modem has 4 lan ports.
    Would it make sence to connect more than 1 lan cable from switch to modem?
    Thankyou
    Cheers

    Make sure you have the latest ROM bios and proliant support pack.
    http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=3948599&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswEnvOID%253D4064%257CswLang%253D%257Caction%253DlistDriver&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
    Install the rom bios, then easiest to boot the HP smartstart to prepare for operating system deployment, then install the complete PSP next.
    Regards, Dave Patrick ....
    Microsoft Certified Professional
    Microsoft MVP [Windows]
    Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

  • "in-network" email  with integrated search-able database for printer room.

    Hi,
    I would like the following procedure to replace the current method of hand writing notes which are associated with files that are put in a drop box by employees to be printed in the printer room.
    They're are about 30 employees that I want to be able to send an “in-network” email with as much as a 2 MB file attachment along with a template describing the file attachment to the printer room were there are 4 computers. The file attachment should go directly to the print server and the template explaining the file attachment along with who and when it was sent to go to a different computer (a PC - could be a MAC) containing one tracking data base. The data base would be integrated with the in network email. The data base would keep track of all the emails and attachments. The data base would be search-able and easy to back up. Their also should also be a pop up notification when new emails/print jobs arrive.
    Computers: Two Print servers controlling two printers each. One Xserve. 30 Mac's running OS X.
    Any thoughts?
    Thanks,
    Jason
    Dual 1GHz G4   Mac OS X (10.4.3)  

    No easy way of doing this with existing server tools.
    Your best bet is to get a professional on site and you will need extra software to be written for you.

  • SMTP password problem with WRT54G or WRV200

    I have a problem sending email in that the SMTP password cannot be successfully sent. I have found that if the router is rebooted, email can be sent for maybe 10 minutes. After that time, the password is refused no matter how many times it is tried. I have tried Thunderbird and Apple Mail as the email client and they both behave the same. I have tried 2 different routers, the WRT54G and WRV200 and they behave the same. I have connected my computer directly to the modem and email can be sent successfully all the time. I am on SBC/AT&T DSL service - it's Yahoo email servers. My computer is a Mac running OX X v10.5 (Leopard). I normally use Thunderbird as my email client and it has worked for some time.

    ISP is SBC/AT&T DSL. The email servers are on Yahoo. I am not sure of the question about private/public address of the router. The IP address of the router is assigned by SBC/AT&T - I guess that's public. The firmware of the WRT54G is the latest from your website. I don't really have a Windows computer to give a verdict on whether it happens there. I have tried using the Apple Mail application and it behaves in the same way as the Thunderbird client. Email sending is normal for about 10 minutes after booting the router and then after 10 minutes the sending of the SMTP password fails. Rebooting the router will get you another 10 minutes of successful email sending. As I described bnefore: If I take the router out of my network and connect my computer directly to the DSL modem, then email can be sent at any time. The computer is logging onto the SBC/AT&T network PPPoE with no router involved. Of course, I do not have to change any settings in my email client for this experiment. This proves to me that the email client is working and configured correctly. Keep in mind that this email client has been working correctly for some time (years) in this configuration. I am always able to receive email from the POP server. Message Edited by darowa on 03-16-2008 02:28 PM
    Message Edited by darowa on 03-16-2008 02:30 PM

  • Help needed to Replace existing routers due to connection drop with Extreme

    I currently have an old linksys router connected to my cable modem in the basement. I then have a second router connected via ethernet to the first router located upstairs since most of my computers are upstairs. I am having alot of connection drops with most of the computers. ONe of the computers hardly even connects to the network. Almost all of my computers are macbook pros/macbooks/imac except for 1 or 2 pcs. I would like to start fresh with the airport extreme/express. Should I set it up similar in that I have an airport extreme base station connected downstairs to the modem and then have a second extreme/express upstairs via the ethernet connection. I do have a printer upstairs as well that most of the computers use that is connected wirelessly.
    Any other tips?

    No,
    Express has only one ethernet port which acts either as WAN input if plugged into a modem or as LAN output, if plugged into an end device (PC, Printer), so it cannot be used for input and output at the same time. I'd suggest you do this,
    1/
    - If modem must stay in the basement and cannot be moved upstairs
    - Have modem in basement
    - Run an ethernet cable from the modem to your Extreme's WAN port upstairs
    - Have Express in the basement and connect it wirelessly
    let it join your Extreme's network over wifi, if there is enough signal in the basement
    - If there is no signal in the basement from upstairs' Extreme and Express finds
    nothing or signal is unreliable, then you need to run an ethernet cable
    from Extreme's LAN port (it has 3 in the back) and run it downstairs
    and plug into your Express.
    2/
    - move the modem upstairs and keep the setup same as in 1/
    - no difference, you still have to run the coax cable from basement,
    so you drill no matter what
    3/
    - keep modem downstairs
    - keep extreme downstairs connected to modem
    - keep express upstairs and join it wirelessly to your Extreme's network
    - plus side is - there would be no cables running upstairs
    - downsides of this setup are:
    you'll have router with only one ethernet port upstairs - so if you have"
    multiple desktops, you will have to rely on wifi
    Extreme's signal is stronger than Express's - I'd put it into a place where
    my family spends most of the time
    It all depends on your house setup, whether you have desktops or laptops only, ...
    As a preference, I like to keep Extreme close to my main computer as I connect to it via ethernet rather than wifi (much better speed). My wifi is only for laptops and iPods.
    Also, seing the Extreme's status light tells me what is going on without running to a basement when internet starts acting up.
    Rule of thumb - if you can drill, then drill and take advantage of the gigabit speed as opposed to wifi's 100megabit or whatever your signal lets you get up to. This is very noticeable when streaming movies via Netflix, AirPlay etc...
    If drilling is too much hassle, you live in an apartment unit or it's a transitory place for you, just use Wifi. If you are planning on living there for a while, cables will make you happier than wifi - no interference to worry about and better speed
    It's up to you.
    My apple TV is also connected to my Extreme via cable - speed is incredible. Wifi used to choke up every now and then.

  • Pls help me.i have a problem with WRT54G wireless router.

    Dear all, Now i got face some problem with WRT54G wireless router.The problem is after i connect to the internet...the wireless will automatic drop..is that any ppl here got face this and got any solution to solve it...?thanks for sharing..

    hi...logon to router's setup page and try changing channel to 11, go to advanced wireless settings, try changing transmission rate to 54Mbps, beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmwar on the router...check whether it maks any difference or not and let me know.

  • AirPort network dropping connection at least twice a day

    I'm running an AirPort network and guest network version 7.6.4 - Time Capsule serves as my router, extreme and express as my extenders.  At least twice a week, my AirPort Network drops wi-fi connectivity.  It's annoying and frustrating as often I'm using a VIOP line for work conference calling and or using web meeting services.  The wi-fi droppage requires me to un/re plug the time capsule - the only fix I've found.  Doing this corrects the issue until the next drop.  Usually a couple of days...
    Is there a permanent fix I can use that I don't know about?  I was under the impression my AirPort Network "would just work"

    Since the Thunderbolt Display has been released I have seen this issue on literally hundreds of display/laptop combinations. With and without the extension cable. I have not found any logic around the issue, trying different usb/thunderbolt ports, different sleep settings, power settings. This is a legitmate issue that should be addressed and Apple is not addressing it -- or can't address it. BTW-There is NO reason to engineer a product with an extension cable needed to operate the peripheral. The only way to solve this is to burn a USB port on your laptop. I am fairly certain the issue is power related over the Thunderbolt bus. However, I have also experienced issues with USB3 hubs on macs. So maybe it is a larger power issue.
    Anyway, an Apple wired keyboard should just work out of the box.

  • O2 network dropping out

    Is anyone else having problems with the o2 network dropping off regularly from their i-phone? I have spoken to o2 and they say i have to send the phone back to apple!
    Someone has just told me that you can download a repair??? Does anyone know anything about it? Help I'm due to leave the country next week and dont have time to send my phone away and get it back before I leave.

    tb64,
    You can try updating to iPhone firmware 1.1.4 to see if it helps resolve your issue if you haven't already.
    Connect your iPhone to your computer, open iTunes and click "Check for Update".
    Hope this helps,
    Nathan C.

  • Possible to extend a network of a WRT54G to my TC?

    Since a macbook cannot be on 2 networks at once. i'm going to need to have my TC act as my backup and as my network. so the WRT54G is plugged into the modem and the modem is plugged into the wall blah blah blah.. i need to know if my TC can extend the network of the WRT54G so that i can connect to the TC and have internet + backup. if this is possible what settings should the airport utility and the time capsule be on??

    Do you have a specific reason for keeping the WRT54G on the network? You can simply replace it with the Time Capsule and keep on going.
    If you want to set up two different networks, one 802.11n and one 802.11b/g, you could also do this. I'd set the Time Capsule up in place of the WRT54G and configure it as n-only which will allow you to have faster dual-channel connections. Then, you can connect the WRT54G to one of the TC's LAN ports and allow it to continue to give you the 802.11b/g network.
    You would have to set up the TC for DHCP and then disable DHCP on the WRT54G. It is a bit tricky to set up but can be done.
    Otherwise, just swap 'em out.

  • Networking imac with powe mac 604e - ethenet?

    Hi i have an older power mac 604e computer
    and i want to network it with a new
    imac. Im trying to get my old files transferred onto my new computer. The old power mac has an old fashion scii connection and it does not have usb nor firewire so i thought the ethernet connection would be the best way.
    this is just a one time transfer of data and i already have an ethernet cable. How do i set this up?
    thanks for the advice
    steven

    The 604e computer has to be running Mac OS 9 or OS X to be able to talk to your iMac running Tiger. You can try to connect the two computers via an ethernet cable and then configure things as follows here:
    http://homepage.mac.com/car1son/os9xnet_nfilesharing.html
    That page indicates that you can also get this to work with system 8.5 and 8.6 but I found those systems to drop connections alot. It may work without a crossover cable if the autosensing features of the ethernet ports work correctly. Lastly if you have an ethernet hub you can use that (with regular cables) instead of a crossover cable. Good luck and keep an eye on things as you may get drops anyway!
    eyeMac G5 2.1   Mac OS X (10.4.3)  

  • Calls dropping with disconnect cause 16 (normal clearing)

    I am faicing a strange problem within my voice network.
    I am using both VoIP and SS7. For VoIP I am using IPIPGW and for SS7 PGW.
    Some calls connect normally but immdeiately drop with disconnect cause 16, or ISDN cause 8090 (which mean normal clearing) .
    I have difficulty on tracing the cause as I don't know where to start from.
    Can someone indicate any poosible cause for this problem or where to start looking at.

    First specify where is the clearing message come from ? where do you see it
    also intitate a debug for isdn q.931 messages to get deep into the cause...

  • K920 - Z2 Pro - Network Fluctuation & Network Drop.

    Hi,
    I have received Lenovo Z2 Pro on 17th November 2014. Since the date of receiving phone has too much of network fluctuations. It fluctuate from 0 to full every 2-3 seconds. it goes to "no service" frequently. All this happens even when phone is kept steady at one location.
    Situation gets worse where there is low network availability. Where there is low network availability, phone goes out of service (doesn't pick up network) very frequently.
    I have 3 other phones which doesn't have any issue picking up network with same sim card at the exact same place. They also don't show any network fluctuations or network drops.
    FYI, I have updated my Z2 Pro to latest firmware via OTA update on WiFi and I also have done factory reset 3 times.
    Does anyone have a solution for this issue or is it a manufacturing defect.?
    Or is it a software issue.?
    Thanks.

    In addition to that, when you put your phone's network on WCDMA \ GSM (Auto) mode, it almost always chooses GSM (2G) network even when WCDMA (3G) network is available.
    My Samsung Note II & other mobiles almost always pick up WCDMA (3G) network when put on Auto mode.
    It does seems software issue.

  • Network problem with vodafone in india, noida

    network pronlem in my iphone 5 for last 8months, please advise what to do?.

    What problem?
    Any network problem with your cell phone carrier you need to take up with the carrier.

Maybe you are looking for

  • Access sequence for stock transfer order

    Hi, My client is a paper industry. client is procuring raw materials from forest center. We are considering forest center as plant 1800 and paper mill as plant 1100. several depots has been created under forest center and considering them as storage

  • Mpd frustration

    I have been using arch for over a year, but recently I reinstalled with x86_64 rather then i686 that I was using before. Now Im trying to get mpd up and running again with sonata but the wiki seems to be missing some important steps or something. Im

  • [JS] Setting font of a textRange

    Hi In Ai CS3, I am trying to set the font of an entire textFrame, using this type of syntax: newFrame.textRange.characterAttributes.textFont.family = "Arial"; Either using 'family' or 'name', this produces no result whatsoever. Anyone willing to shed

  • One of the tv episodes I downloaded is showing video fuzz, but with clear audio?

    One of the tv episodes I downloaded is showing video fuzz, but with clear audio. How do I get a new episode sent to me without repurchasing?

  • PXI 6030e Voltage measurement

    Hello All, I have a PXI 6030E DAQ with a SCB-68 connector board.  I am setting up a simple voltage divider and connecting my Vout to pin 68 on the SCB-68.  My ground is going to pin 67.  My Vin is 5 V DC.  I used DAQ assistant to automatically genera