Network/ethernet problems

Hi. Constant problem, every single time I turn on my computer it has no internet, but then I click on 'network' in the system prefs and a window jumps out to say "new port detected.....Built in ethernet" every single time! Click ok and then it finds the connection and we're cooking. But what can I do to fix this?
Now to my knowledge I've not altered any settings, my internet (direct plugged in cable through set top box) has always worked fine and this problem just started up about a month ago. Is there any other info needed for someone to answer? Thanks a million in advance.
Dan

You may want to consider booting the installation CD, starting 'Disk Utility' and doing a 'Repair Permissions'.
After that, reboot into Safe Boot, http://docs.info.apple.com/article.html?artnum=107393.
Then reboot again and see if it starts behaving (you may need to go through network config one more time to know for sure).
Wondering if a preference file isn't getting written due to a permissions issue.

Similar Messages

Hp Officejet Pro 8600 Plus network printing problems

I hard wired my Hp Officejet Pro 8600 plus with an ethernet cable to my router to enable other computers on my network to print to my printer. Several problems have resulted because of this:
1. I cannot find my printer in the Device Manager: it shows as an "unknown device"
2. Sometimes pdf files will print and sometimes they will not. Word and Excel files sometimes print, and sometimes don't.
3. Sometimes documents will spool, but then I get the following message: "Unable to communicate with printer." Then it asks me to make sure all cables are connected and power is on, which is the case.
I have tried all kinds of troubleshooting with information found in Hp forum and on Hp website. Finally, using the HP Print and Scan doctor, I deleted and reinstalled the printer and updated the Full software and drivers. Then I got a message saying "the printer is on your network, but the network software is unable to find it using the typical network discovery method. You can install the printer and operate it normally over the network using the IP address of your printer." I inserted the IP address and it took me through various steps to final installation. I typed a short message into a new document on Microsoft Word and it printed, Then I tried to print some information from the HP website, but this did not print; it didn't even spool.
My router is not detecting the printer on the network either, the light on the port bearing the network cable connected directly to the printer has never been shown to be on, like the other lights. I have been struggling with this for the last several months.
I have an Hp computer, running on Windows 7 Ultimate (64bit). I prefer to use my printer over a network ethernet cable instead of wireless. Please help!

techlearner3 wrote:
My router is not detecting the printer on the network either, the light on the port bearing the network cable connected directly to the printer has never been shown to be on, like the other lights. I have been struggling with this for the last several months.
I believe this is the cause of your problem. First, try another known working port in the router. Next, change the Ethernet cable with a known good cable.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

MacBook to iBook - Networking ethernet/firewire/IP/Sharing

MacBook to iBook - Networking ethernet/firewire/IP/Sharing - This is the problem:
1. Firewire : I setup with firewire a MacBook to iBook IP network hub to use my MacBook over the iBook the net. Works 4 times without a problem, easy to set up, great ! Now it won't - green network status symbol in Sys>Network on booth computer. Firewire port selected on the top, as been advice already
( http://www.macdevcenter.com/pub/a/mac/2003/11/11/panther_internet.html )... IP Address is activ, but now it won't go on the net over my iBook with the DSL modem. Can't use the modem on my MacBook(SpeedTouch 330) Thats why ! But what is the problem now with the firewire connection ?
2. Ethernet : Same problem as with firewire and i have this: Conect to server - "Registered User" - ask me for Password ? No Password is setup on booth computer, but it refuse to conect : "Conection Failed" Unknown user, incorrect password ! Strange stuff...
Any help or advise would be great
Many thanks for help in advance !
Stefan

To connect to another computer on your home network as a registered user, you need to enter the administrator's name and password for the computer you are trying access.

Macbook Pro ethernet problems

Hi All:
First post here. I have a 15" first generation MBP, and I'm having some ethernet problems. When my ethernet works, it works fine. However, if i were to shut down the machine and disconnect the ethernet cable, I cannot reconnect to the ethernet. In Network Preferences, Ethernet is not available in the pulldown and it appears gray-ed out in the Network Port Configurations. Restarting the computer, unplugging or resetting the modem doesn't help. Also, the PC link light on the modem will not be lit (but is lit when working).
The computer will not connect to any ethernet network, no matter where I am.
I've noticed if I keep resetting both comuter an modem a couple dozen times over a few hours, the PC link button will light, and upon next startup the ethernet connection will be restored. What do you guys think the problem is? It seems abnormal to me.

Had a similar situation with mine back in January, 2.16 Intel.
After spending 3 nights with my Cable ISP as the connection would drop-off, ethernet light flicker green,amber etc.
Took it back to Apple dealer, connected to Dealers network same problem. Cause:::: Motherboard had to be replaced, possible soder loose on the MO. Got it back in 10 days, haven't had a problem ever since.
Suggest you take back yours to have Apple dealer try this out.
zimer

Network Extender problems w/Qwest customers during July 2011

I believe I have found the cause of the Network Extender problems surfacing in July, 2011. I am a customer who has been out of Network Extender usage for two weeks now. Read on....
Unbelievably, almost no one at Qwest, Verizonwireless, or Samsung (NE's manufacturer) has any idea what the cause is and neither Qwest nor Samsung knows that a problem exists at all.
After many hours on the phone to all three companies I finally believe I know the cause of the problem. The cause is an updated firmware revision that was pushed to all Qwest customers who use the Actiontec PK5000 modem/router. They have been pushing it out over the last few weeks, so the symptoms have been rolling rather than happening all at one time.
The latest version of the PK5000 firmware is QAP002-3.60.3.0.9.9 When the customer's modem receives that version update (unbeknownst to them), Network Extender is rendered inoperable... the modem does not recognize the NE is plugged into it and does not provide an IP address. The WAN light goes solid red, the GPS goes magenta and the SYS light goes red.
Because Qwest's PK5000 works fine with the upgrade (i.e. both wi-fi and ethernet connections work fine with my Macintosh MacBook Pro), they have no interest in solving my VerizonWireless problem.
Bottom line is VerizonWireless needs to get a patch created "yesterday" and made available to all Network Extender customers who use the Actiontec PK5000 Qwest modem/router immediately. I live in a rural area and despite the fact I've had a VerizonWireless cell phone for many, many years, I'll be forced into changing cell phone providers soon, as will every other NE user who has lost their NE usage because of this problem.
It boggles my mind that no one has figured this out and provided a patch for the Network Extender. Understandably, Qwest could care less this is happening, since their service is not effected. This is truly VerizonWireless' problem.
Now, what can you do??? Call customer service right now and get technical support. Give them the information above and let them know they need to develop a patch for the Network Extender to work with the new firmware (i.e. operating system) of the Actiontec PK5000 modem. It's only when they hear from a bunch of people that they will step up the urgency to find a solution. Thanks!

OK, what's the deal here. I've been having the same problems. Verizon gave me a new extender and I still have the same problem. The week of July 15th everything went dead. I live in downtown Denver and I still can't get service at my house. My network extender is no longer compatible with the PK5000 modem QWEST issued. Firmware got pushed out? uhh... OK that doesn't mean anything to me. Not my problem, but kudos to the gentlemen who figured that out.. Neither Verizon or qwest seem to not want to take responsibility.
So what's next? is there an extender on the market that is compatible with the infamous PK5000? Evidently, the guys @ Qwest I was on the phone with for 45 minutes seems to think it's some type of high speed low drag, technological phenomenon. I'd like to add that if someone from qwest or verizon tech support reads this, I do not have a land line at my house, I have never had a land line at my house so no I can't go to my desktop and troubleshoot the modem while on the phone. just to reinterate I live in downtown denver I do not have cell coverage at my house, and no it's not my house. Everyone in our area does not have coverage.
I've had verizon for over 10 years now and never had a problem. This is the first and biggest problem I had becasue verizon and qwest decided to "bundle" thier service offering...whatever that means.
I believe I have found the cause of the Network Extender problems surfacing in July, 2011. I am a customer who has been out of Network Extender usage for two weeks now. Read on....
"Unbelievably, almost no one at Qwest, Verizonwireless, or Samsung (NE's manufacturer) has any idea what the cause is and neither Qwest nor Samsung knows that a problem exists at all.
After many hours on the phone to all three companies I finally believe I know the cause of the problem. The cause is an updated firmware revision that was pushed to all Qwest customers who use the Actiontec PK5000 modem/router. They have been pushing it out over the last few weeks, so the symptoms have been rolling rather than happening all at one time.
The latest version of the PK5000 firmware is QAP002-3.60.3.0.9.9 When the customer's modem receives that version update (unbeknownst to them), Network Extender is rendered inoperable... the modem does not recognize the NE is plugged into it and does not provide an IP address. The WAN light goes solid red, the GPS goes magenta and the SYS light goes red.
Because Qwest's PK5000 works fine with the upgrade (i.e. both wi-fi and ethernet connections work fine with my Macintosh MacBook Pro), they have no interest in solving my VerizonWireless problem.
Bottom line is VerizonWireless needs to get a patch created "yesterday" and made available to all Network Extender customers who use the Actiontec PK5000 Qwest modem/router immediately. I live in a rural area and despite the fact I've had a VerizonWireless cell phone for many, many years, I'll be forced into changing cell phone providers soon, as will every other NE user who has lost their NE usage because of this problem.
It boggles my mind that no one has figured this out and provided a patch for the Network Extender. Understandably, Qwest could care less this is happening, since their service is not effected. This is truly VerizonWireless' problem.
Now, what can you do??? Call customer service right now and get technical support. Give them the information above and let them know they need to develop a patch for the Network Extender to work with the new firmware (i.e. operating system) of the Actiontec PK5000 modem. It's only when they hear from a bunch of people that they will step up the urgency to find a solution. Thanks!"

T41 has Network Controller problem

I was given a T41 2373-7JU that I loaded with XP Pro. My problem is it will not connect to the internet via it's browser. In Device Manager it shows a Network Controller problem and I've been unable to correct this no matter how many different drivers I've tried. Also, how do I tell if there's an internal wireless card inside? It did connect to the internet earlier today using my USB adaptor but now I can't even do that anymore. I've tried a dozen or so solutions without any success so where should I go from here?

Hi and welcome to the forum!
Following are the drivers you need for Ethernet and wifi card (and yes, as per support page there's an internal card installed in your system):-
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-62922
http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-42683
To install the drivers successfully, you need to run the .exe setups from C:\Drivers.... for each device after the first setup completes.
For ethernet, the setup is in C:\DRIVERS\Win\ETHERNET\PRO1000\Win32 and for wifi C:\DRIVERS\WLLANCSC.
Hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Time Capsule compatibility with network (ethernet) printer

Does TC support connecting a network printer (all in one) via an ethernet connection?
The manual doesn't show anything on this just usb descriptions. I have Time Capsule mainly used as a router connected to my modem. 1 Imac, 2 wireless mac laptops, and 1 wireless pc using the network - no problems w/internet or file sharing etc. However, I don't see through airport utility that there is any spot to set up network printer just USB. I would like to use my Brother MFC-5840cn to network print and scan to folders. Please help solve this question if you can. Previously I did this with a linksys router. Thanks!

I still have questions about how to connect the Brother printer through ethernet. When connected does the airport utility have some area where you can identify the printer as a network printer as opposed to USB?
The AirPort Utility would only come into play if the printer was attached to the TC's USB port. Printers, attached by Ethernet, would have to "network-ready." Controlling these types of printers would be through the printer driver that you would access through the operating system interface.
In my HP example, the HP printer driver does provide access to a number of features particular to this printer model. Most manufacturers include an installation CD that provide useful utilities ... albeit most are written for Windows. I would suggest checking out the Brother support site to see if they have Mac-specific drivers or utilities.

Using USB 2.0 Network Ethernet Adapter for sharing printer with 3 computers

Hi all,
Opposed to using a print server, can I use a USB 2.0 Network Ethernet Adapter to connect my Epson printer over my ethernet DSL router?
Thanks
Web dude

Yea, I thought about an adapter for the USB 2.0 port, but for a few bucks more, get the USB 3.0 adapter and be able to connect to Ethernet at Gigabit speeds!
Since Lenovo has not commented on the absence of an Ethernet port, I'm guessing that the slim height of the Yoga prevents it, unless you go to some funky slide-out module and connect at a 90 degree angle (which would be a worse design). I had an old Thinkpad (or Dell?) with that design, and they are intermittent and subject to being broken off.
Bundling in the Ethernet Adapter would have been a nice touch. Perhaps they were trying not to increase the Yoga's "above market" price further.

My daughter has just bought me an iPad 2 from Dubai and set it all up for me but unfortunately the iMessage function doesn't seem to work. We keep getting messages,when trying to activate it, that there is a network connection problem - help!

My daughter has just bought me an iPad 2 from Dubai and set it all up for me but unfortunately the iMessage function doesn't seem to work. We keep getting messages,when trying to activate it, that there is a network connection problem - help!

Thank you both for your responses but my daughter was reassured by the salesman in the iStyle store (official Apple store in the UAE) that iMessages would work but conceded that FaceTime wouldn't. My iTunes account is registered in the uk and my daughter's iPhone has iMessages even though she bought it (and uses it) in Dubai. Can anyone else throw any light on this?

HELP!!! Mac G4 450mhz dual ethernet PROBLEMS!

Hello, my mac is having a serious problem with the internet. It won't connect, and even though i have a ethernet cable plugged in, it says i don't. Everything was working fine until i left for 2 days and and plugged it for that time. I need the internet in that mac as soon as possible.
PLEASE HELP ME!

I too, am having the same problem... but mine isn't because of the possible software update, it just flat out doesn't work!
I too, have tried asking for help with the possibility of (hopefully) restoring the driver/extension... but after reformating the drive and reinstalling the software from 10.2, to 10.2.8 and it still failed to work, I ended up buying a Belkin Gigabit Ethernet PCI Card that has FAILED in every way!!!
The Belkin card will work as a one-time thing, and after restarting or disconnecting the Ethernet cable, it fails to function and fails to be "selectable" within the Ethernet configuration "Show:" options.
...so don't buy the Belkin...
I have yet to resolve my dead Ethernet problem, and it is... a problem!
I know this isn't contributing much of anything, but don't waist your time with the Belkin. I bought one, it acted in the way described above, and the Belkin Tech Support suggested I exchange it with another one, and so I did... and it too... is acting in the manner described above.
No resolve... no Ethernet... no on-line schtuff. not on that G4!!!
Jon

Network Accounting Problem

I have a serious network accouting problem arisen from content engine:
Our routers are connected to internal backbone router with enabling Netflow to bill the usage (from domestic to backbone) of each users.
However, the CE will affect the network accounting seriously because it will replace the sender IP address with its own address before sending out to the link.
Would you give me some solution to remedy the problem?
Very Very Urgent!!
Thanks a lot..
Alex

Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting.

Having issues with picture messaging get told to go to settings, then general, then network then cellular data network. my problem is there is no such option my phone is a 3gs

having issues with MMS messaging instruction for setup, are to gotto settings, then general, then network then cellular data network.My problem is there is no cellular data network optiion on this page have tried resetting phone , no good .Help.

That option does not exist depending on who the carrier is.
Who is the carrier? Are they a supported carrier?
Have you tried Settings > General > Reset > Reset Network Settings?

When i enter my apple id into i message it says it has a network connection problem even though it has full internet?

when i enter my apple id into i message it says it has a network connection problem even though it has full internet?What can I do???

See my response to one or your three posts.

HP 14-d017AU: Issues with Webcam, Network, Ethernet, VGA and PCI Device drivers

I downgraded my new HP 14-d017AU to Windows 7, 64-bit. Since then I have not been able to find drivers for Webcam, Network, Ethernet, VGA and PCI Device. The Hardware IDs are as follows: Ethernet Controller: PCI\VEN_10EC&DEV_8136&SUBSYS_2191103C&REV_07Network Controller: PCI\VEN_168C&DEV_0036&SUBSYS_217F103C&REV_01PCI Device: PCI\VEN_10EC&DEV_5229&SUBSYS_2191103C&REV_01Universal Serial Bus (USB) Controller: PCI\VEN_1022&DEV_7814&SUBSYS_2191103C&REV_01Standard VGA Graphics Adapter: PCI\VEN_1002&DEV_9834&SUBSYS_2191103C&REV_00I will be grateful for your assistance.

Hi: See if this works... Graphics: Install and reboot. http://support.amd.com/en-us/download/mobile?os=Windows%207%20-%2064 USB 3: Install both of these and reboot. http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_137148_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133037_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Wireless: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswItem%253Dob_128686_1&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken PCI dev: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133237_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Ethernet Controller: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=6943836&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_133348_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Webcam: (won't work until the graphics driver is properly installed). http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-131219-1&cc=us&dlc=en&lc=en&os=4158&product=6825117&sw_lang=

Hp slate 6 heating problem, network connectivity problem and now camera problem

Hello, I have using this tablet since last 4 month and after upgrading to kitkat there is phone heating problem and network connectivity problem getting started some time it will show network but during that we can not receiving or calling through it and even after put in flite mode it will not resume so have to restart several time. Now about 4 days ago kernal updating automaticaly in my phone so i happy that may shortout the all problems but rather than it will added one more problem which related to camera while goes in setting of camera it will automatically closed. Have you tested this tablet or not ???? and why from your site any actions has been taken ???Why there is no Solutions are given from your site????

Hello Rohit,Can you check if you updated to the latest version?Here is the link: (you can choose the latest version to download and update it by SD card)- base on your regionhttp://support.hp.com/us-en/drivers/selfservice/HP-Slate-6-VoiceTab/6818329/model/7386537

Network/ethernet problems

Similar Messages

Maybe you are looking for