Network Extender stopped working with new FIOS Quantum router

I have had a Network Extender for a few years (the older 1x model, SCS-26UC4) but it stopped working when I upgraded to FIOS Quantum. That upgrade included a new router.
I have opened the TCP (53, 52428) and UDP (500, 4500, 52428) ports on the router without much luck.
The Network Extended does seem to work if I bypass the FIOS router and connect the Network Extender directly to the WAN. So it seems the issue is in the router configuration.
All lights are blue except for the SYS light, which cycles from fast red blink, slow red blink, steady red and then blue for a while. When it's blue the extender works (which I can tell by the sound my phone makes when it connects via the Extender). But then it goes back to red.
One thought I had was to open a DMZ on the router but I cannot find the instructions. It's the Actiontec MI424WR router.
Help appreciated.

Try page 83 in the user guide for the DMZ.
Call Verizon Communications and tell them your Verizon Wireless Network Extender does not work when connected to the router, but it does work when connected directly to the ONT. You shouldn’t have to use a kludge (DMZ) to make it work, the router should be smart enough to figure it out.

Similar Messages

ICloud shared photo stream stopped working with new photo app

iCloud shared photo stream stopped working since the last OX update with the new photo app. I don't have access anymore to the sharing albums, even those that I own

iCloud shared photo stream stopped working since the last OX update with the new photo app. I don't have access anymore to the sharing albums, even those that I own
Don't the albums show at all?
Are you signed in with the same Apple ID that you used with iCloud before? And are you currently browsing the System Photos Library? Only one Photos library, enabled as the System Photos library can sync with iCloud.
For me it helped to disable iCloud Photo sharing in the System Preferences > iCloud > Photos > Options
and in the Photos. app Preferences < iCloud.
Then restart the Mac and enable the same Preferences again.
And wait.
The Shared albums came slowly back and were all back after one day.

Network Extender Stopped Working - Resolution Keeps Getting Pushed Back

I have had good service with a network extender for about 5 months until last Wednesday (Sept 28). Actually, I had acceptable service in my home WITHOUT a network extender until Verizon started testing 4G in my area last spring/early summer. Then, my service went from okay to NONE. After numerous calls to tech support and escalations, an alleged "field test" was conducted on my street. Conclusion: Foliage from trees causing signal loss. Solution: $125 for a network extender. Foolishly (as I later learned) I payed the $125 (many people claim to have received the free after reporting numerous problems and threatening to cancel service)...anyawy, last Wednesday I noticed @ home that my signal was varying from 3G to 1x, and the signal bars were all over the place. My phone is showing 1x @ about -70 dbm, and either NO 3G or with a signal of -120 dbm or worse. On rare occasions I will get a brief 4G indication. I did the usual, removed battery from phone, etc. but later learned that my wife's phone was doing the same thing. According the the latest Verizon map I an deep within a 4G coverage area, yet can hardly get a signal of any kind within a 1/4 mile of my house without the extender. While troubleshooting on my own and with Verizon tech support, I power cycled the network extender (all lights are on as they are supposed to be), ran the 8x8 VIOP test on my DSL service (it passed with flying colors), reset my DSL modem and router, refreshed DHCP on the router, checked all settings on both Verizon phones in the house. Dialing #48 indicates that I am within network extender coverage, yet the signal varies from 1x to 3G/5 bars constantly as I sit in the room with the extender. Several calls to tech support, two escalations, power increased on extender, resolution promised within 24 hours, then 48 hours, now today was told 72 hours.
My questions are: Why suddenly signal loss to two phones from the extender after ruling out 2 phones and ISP, why such a poor signal at my home (not just inside...anywhere within a quarter mile) in the first place when the coverage map shows I'm well within the 4G coverage area, why is the resolution being pushed back every time I call to inquire?
Any help, especially from Verizon, would be appreciated.

I started on another string, but reading this tells me we have the same problem. Got the extender, everything programmed, phones indicating connection to the extender network, but now I have the same issue. My wife's Iphone shows great signal, but the words are clipped as well. My Droid X has no better signal strength indicated than before, (yes, it gives the short double beep so it must be connected) and the voice quality is bad enough that one can't understand the caller. I can get signal directly when outside well enough to make decent phone calls. When I go outside and away from the extenders range voice transmission returns to normal---though occasionally I will drop a call in normal transmission. I have good 3G outside (3-4 bars though sporatic), but as soon as I try to make a call the signal drops to one bar on 1x. Therefore, the reason I got the extender so we could make calls inside the house rather than walking outside in subfreezing weather!!
Same routine,...called Tech service and got a rep. She couldn't do anything but tell me that it had to be the "contruction materials in my house". Said we must have brick contruction,....no, it's vinyl siding. I did say that we had a foil backed insulation material surrounding the house and she quickly affirmed that had to be the problem. It was blocking the signal inside the house and the extender wouldn't pick it up.
But if the extender is in the window, doesn't that solve the problem? Point---if we stand at a north or east window (we have large windows on both sides) we are able to get a signal on the phone, but the service is "iffy." Again the reason for the extender. She repeated again "Verizon can't do anything about the contruction materials in our house." Then she said that the extender is designed for "people that live along the 'coasts' that have weak signal!!??" That was a hint that it wouldn't work in the midwest. Her final comment was that the extender wouldn't work if we had weak signal in the area(interesting that was said after her indicating that it was designed for customers with "weak" signal.) When I asked why it was connected to the internet, I didn't get an answer. I could tell I wasn't going to get information to help so I thanked her and gave up.
So were these excuses or reasons? The local store that told me to get the extender knows absolutely nothing---"just call tech service." I've had calls to 611 now three times, reprogrammed, reset the unit, and it still doesn't work. I'm not even going to ask anyone in the forum to help as I'm sure that others are just as frustrated. Verizon claimed the best technology and customer service when we switched a year ago. We were shown on the map well within the 3G territory, but quickly found out that those maps are not accurate. While we live on the prairie (flat land), our normal signal goes from 1x to 3G and back constantly. At night the signal is weaker than daytime. Sometimes we have 3, even 4 bars of 3G and 2 minutes later 1 bar of 1x. ( I'm sitting here watching my phone do that right now.) The only solution is to go back to ATT. We dropped calls with them, but at least could talk in the house with their phones. It's costly to switch as we have to buy out the contract, but this service is unacceptable.
The real issue is credibility of the company. I was told that we would be far more satisfied with Verizon service; and that if there were ever any problems---they would be fixed. That wasn't a true statement. I wish there was a credible alternative to both ATT and Verizon in our area.

Time Machine stopped working with new Mac address.

Greetings,
I have an IOMEGA 500, FireWire which I used to use for Time Machine. I now have a new Mac address and do not have access to the old Mac address. Is there any way that I can get the IOMEGA to start working with Time Machine? If so please give me step by steps instructions on how to make this external hard drive work again with Time Machine.
Any help is most appreciated.
Thank you for your attention to this matter.

macuserr222 wrote:
Greetings,
I have an IOMEGA 500, FireWire which I used to use for Time Machine. I now have a new Mac address
Do you have a new Mac, or a new logic board? Either will get you a new MAC (Media Access Control) address, which Time Machine interprets as a different Mac.
Do you mean you haven't started doing backups of the new Mac, and want to view the old ones? If so, see #E2 in [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html] (or use the link in *User Tips* at the top of the +Time Machine+ forum).
If you want to use the old backups to set up a new Mac, see [Setting up a new Mac from an old one or its backups|http://web.me.com/pondini/AppleTips/Setup.html] (or use the link in *User Tips* at the top of this forum).
When you do your first backup, OSX should ask how you want to handle the old backups. See #B5 in Troubleshooting for details.
If that's not what you mean, please explain exactly what's going on, and what happens when you try to do whatever you're doing.
Message was edited by: Pondini

My imovie application stop working with new OS

Hi,
My imovie application stopped working. I have reset the computer several times and it appears the application is damaged. I can enter but I no longer see my existing projects and none of the commands or icons work. The new project that I was working on is still visible but frozen. I just updated my Operating system. First Leopard and then Mountain Lion.
Any advice on what can I do to be able to restore the application and keep my existing projects?
Thanks,
Adriana

Hi Mitch,
You should have an update for iPhoto waiting in the App Store. If you don't, go to the App Store and type iPhoto in the search bar. It should display the app, and have "Update" in the place where the price normally is.
Cheers,
GB

Airport express G not working with new linksys N router

I just swapped a new linksys N router into my old G network and my old airport express is flashing amber and refusing to acknowledge the network. It does not seem to be picking up. What does this mean and how do i fix it? thank you in advance

someone posted this anyone , not sure i actually understand all of it
hours of digging through blogs and Apple help docs, with some luck and trial & error, have gotten it to work. This experience seals the deal...if a Mac can ever run Excel, I'm abandoning my PC.
For the benefit of anyone else in my situation, here's what I did:
You have to override Airport Express's default desire to make itself the hub of a new network, and force it to be added as a client to your own network.
First, plug the Airport Express into the wall, then reset it by holding down the reset button with a paper clip for about ten seconds. Plug in an ethernet cord that's attached to your wireless router.
Open the Airport utility which you should've installed from the cd in the package. It should now recognize your Airport Express and the light will turn green. Be patient...mine took awhile, and even started flashing amber before it worked.
You will need to manually configure the AE from the utility by typing in the name of your wireless network, setting AE to "join an existing network" instead of its default "create new network," and enable Airtunes.
You may need to add the "Airport ID" printed on the case of the unit to your router's MAC list. This allows the router to recognize the device. Type your router's IP address into the address bar of internet explorer to access the router settings.
If you don't see your speakers listed in a box at the bottom of iTunes, you will need to go to the settings window (in iTunes) and click "search for remote speakers connected to Airtunes."
gonna try it out, cause nothing else has worked

Web Service (SOAP) stopped working with new update

We've got a SOAP service that sits on a second server that
our main flash file calls to. It's work just fine until we've
updated to the latest Flash player 9. I've read about the Socket
Policy file and figure that is the issue. We are on a hosted server
and I don't have the ability to add a perl server so that it can
serve the policy file out on a different port. We did have to add a
crossdomain.xml file and that has been working great prior to the
update. My question is this.
What can I do to get the SOAP service working again without
the ability to add the socket policy file server?
Can I put a policy file up on the server and have it grab it
from the http server?
If so what does that file have to be named and where does it
have to live?
Why can't I find an article about this written in plain
english? ;-)
Thanks

This has nothing to do with socket policy. That's specific to
sockets.
What is -does- have to do with is headers. You have to have a
crossdomain.xml file on the wsdl server allowing the header
requests to come in from your SWF.
You need to specifically allow the SOAPAction header through
to that same server via policy. Do NOT allow all other user-defined
headers using a wildcard, unless you really feel comfortable with
any possible SWF on your servers. But I’d recommend against
it. And you don’t need to add the ‘secure’ tag as
long as the wsdl isn’t on an https server..
Here's an example that also covers meta-policy:
<?xml version="1.0"?>

<cross-domain-policy>
<site-control permitted-cross-domain-policies="all" />
<allow-access-from domain="*.bent.com" />
<allow-http-request-headers-from domain="*.bent.com"
headers="SOAPAction" />
</cross-domain-policy>
This would allow a SWF on bent.com to read wsdl from wherever
this crossdomain.xml was served from.
There -is- a lot of info around this. But it for sure is
complicated and unfortunately it's something you just have to
learn. It's especially important to know how to turn on the
policyfile logging..
So although it's complex english, it's still english:
http://www.adobe.com/devnet/flashplayer/

Slingbox Solo no longer working with new Airport Express router

Help! I'm at the end of my tether trying to get my Slingbox to communicate with the new Airport Express I've just bought. Here's the deal...Obviously, as AEXP only has one Ethernet Port (under advisement) I had to go and buy a 5 port Ethernet switch. Cable modem connects to 1 port of the switch. AEXP connects to another port. Slingbox connects to 3rd port. Network light on Slingbox flashes incessantly and Slingplayer software tells me to makes sure the "Network Router the Slingbox is connected to has the correct Port Forwarding settings."
I have tried (via google) but cannot make sense of this. There should be no firewall obstacles as i am using MAC filtering and have added the MAC address of the slingbox to the AEXP settings. I know that Slingbox does work as it worked fine before with my Belkin router. Please can anyone help? I have called slingbox for ages and they are unable to help. Here's hoping someone here has brains and the patience i don't have! Kind Regards.

identitytheft, Welcome to the discussion area!
Sorry but you need to replace the Ethernet switch with a router which has more than one Ethernet port.
Since the AirPort Express (AX) only has a single Ethernet port it can not properly share an IP address to Ethernet clients.

Photoshop Extended CS 4: 32 bit & 64 bit has stopped working with an error 131:4

Dell XPS 720 Quod Processor 8GB Memory Running Window 7
Both Photoshop Extended CS 4: 32 bit & 64 bit has stopped working with an error 131:4. which stated to reboot to solve the problem. After several attempts at rebooting the computer, I received the same error message.
I was in the process of updating all my Adobe software in order to tackle an Adobe Media Encoder problem: when I sent a stream from the time line to be converted to an AVI file from Premiere Pro CS4 to Encoder the window appeared & hung.
I want to treat the Photoshop problem first. How do I proceed?

Unable to Re-install Adobe Photoshop cs4
A few years back my brother bought me a Dell Studio XPS 8100 running Windows 7 pro.
I have 8 gig's of ram and has a 32 and x64 bit system, right now it is enough for my needs and I can easily spare a gig or two for this program.
I cannot install this program again. I have used iYogi, Adobe Tech, support and am wondering if it makes any difference whether I install it on a x64 or 32 system?
Why can't i re-installl the program. I used it a lot and I do miss it.

HT1655 I have a 3rd generation shuffle. It has stopped working with the earphones it came w/pinch buttons on the cord. It will no longer advance to next song/change the volume. Even with a new set of Apple earbuds, it does same thing. How do i factory

I have a 3rd generation shuffle. It has stopped working with the earphones it came w/pinch buttons on the cord. It will no longer advance to next song/change the volume. Even with a new set of Apple earbuds, it does same thing. How do i factory reset or fix the problem?

Hello there, RufusChloe.
The following iPod Troubleshooting Assistant should help with troubleshooting your issue:
Apple - Support - iPod - iPod shuffle (3rd generation) Troubleshooting
http://www.apple.com/support/ipod/five_rs/shuffle3gen/
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Thunderbolt camera stopped working with Skype and Google Hangouts

Some time ago my built in camera on the thunderbolt stopped working with Skype. If I activate the camera the green light turns on but the screen either remains black or it shows that spinning loading incon forever. The green light stays on indicating the camera is active no matter what I do with skype even if I press the button to deactivate the camera. The green light remains on until you completely kill skype. Rebooting, reinstalling skype, etc. does nothing.
Today I disocvered I have the same thing with Google hangouts. All the way around exactly the same and the green light won't turn off until you kill the web browser. Same thing with FireFox or Safari. Also it no longer works on Viber either.
It's quite infuriating.
I am not sure if this has anything to do with this awful virus like program called "CamTwist" that I installed once and had a very difficult time removing or not.
Reinstalling OS X from scratch is not an option. Too much work, too many programs to reinstall and reconfigure etc.
How can I get my camera back?
The camera works just fine with Photobooth and facetime.
Thanks.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1250 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1000 225 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:per sec:ms/s:KiB/s:%:total:MB:total' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%d MB: %s\n' '\n    ...and %s more line(s)\n' '\nContents of %s\n    '"${k[22]}"'mod date: %s\n    '"${k[22]}"'checksum: %s\n%s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS=":";if(system("sw_vers -productVersion|grep -q ^10\.1")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' { sub(/ :/,"");print|"tail -n'${p[10]}'";} ' ' NR==2&&$4<='${p[7]}' { print $4;} ' ' ($1~"wir"&&$2>'${p[22]}')||($1~/P.+ts:/&&$2>'${p[19]}') { print $1" "int($2);} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q":"$0":"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS=":";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n    "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n    "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n    "$5" => "$3" (UID "$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n    "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+5;i++)u[i]=u[2];split("'"${k[28]}"'",l,":");for(i in o) print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n    "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n    [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n    "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n    '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/, .+:/||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/:/;s/(\n)c/\1:/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */    /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/:(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}':/;s/ *: */:/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS=":"} { printf("'"${f[6]}"'",$1/1048576,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") D=D"\n"$1;} END { print D;} ' ' NR>1&&$3!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $3":"$2;} ' '|tail -n'${p[6]} ' $1>1 { $NF=$NF" x"$1;} /\*/ { if(!f) f="\n\t* Code injection";} { $1="";} 1;END { print f;} ' ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub("\"","",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;if(i=='${p[24]}') nextfile;} END { if(i) print h;for(j=0;j<i;j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|(mplet|nabl)ed|ry HD|safe b|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pagin|Purg(ed|in)|error|Refus|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1:%@d:%s:%d\n\",@a);printa(\"2:%@d:%s:%d\n\",@b);printa(\"9:%@d:%s:%d:%s:%d\n\",@c);printa(\"10:%@d:%s:%d:%d\n\",@d);printa(\"11:%@d:%s:%d:%d\n\",@e);printa(\"12:%@d:%s:%d:%d\n\",@f);printa(\"3:%@d:%s:%d\n\",@g);printa(\"4:%@d:%s:%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{auto*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list '-F "" -k Sender hidd -k Level Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' print\ system --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {'$TMPDIR../C ','/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s -type f -size +'${p[11]}'M -exec stat -f'%z:%N' {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|commit - no t|deprec|Goog|realp|sandbox ex|/root" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console}\ log Activity SMC Login\ hook 'I/O per process' 'High file counts' UID Daemons Agents XPC\ cache Startup\ items {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ {caches/logs,overrides} Shutdown\ codes Heat Diagnostic\ reports Bad\ plists Free\ space VM Bundles{,' (new)'} Trust\ settings );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99; for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 65 6 76 13;D2 45 20 52 66;D4 66 7 77 14;D4 17 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 25 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 59 4 65 76 91;D4 63 4 19 44 75 95 96;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 12;D4 15 5 72 12;C4;};D4 16 5 73 12;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 18 31 107 94 74||{ B2&&A1 18 26 94 74;}&&{ B7 11;B4 0 0 11;C3 23;};A1 18 26 94;B7 11;B4 0 0 11;C3 24;D4 60 14 66 92;D4 58 14 67 93;D4 26 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108; A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 109;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

My firefox has stopped working with my comcast email. It is loading fine on safari but it is no longer loading my email in a timely manner. Comcast says it is a firefox problem. They suggest I uninstall and reinstall firefox. Do I just drag everything to

My firefox has stopped working with my comcast email. It is loading fine on safari but it is no longer loading my email in a timely manner on firefox. Comcast says it is a firefox problem. They suggest I uninstall and reinstall firefox. Do I just drag everything to the trash and download a new version? in English
== URL of affected sites ==
http://
== User Agent ==
Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10_4_11; en) AppleWebKit/531.22.7 (KHTML, like Gecko) Version/4.0.5 Safari/531.22.7

"Clear the Cache": Firefox > Preferences > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove the Cookies" from sites that cause problems: Firefox > Preferences > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

Windows 7 x64 Network Adapter Stops working on high load

My Network has been failing and it has been happening for about a month or so on Windows 7 x64. I dont think that the system configuration is the problem as it is happening on 2 seperate machines. One being a relatively beefed up "white" box, 4 gig OCZ ram, EVGA nForce 790I SLI Mobo, Q9600 Quad core processor, dual raid 1 - 150 Gig Raptors, 2 8800GTX SLI cards, Pure Power 800W PS. The second machine is an IBM Netbook S10. I use the Netbook as a media center connected to a Pioneer Elite 1050HD. One thing is I have a PS3 and have several 1TB Esata drives connected to an IOGear 3132 Esata 3.0Gb pciX card to my desktop.
My typical usages:
1. FTP from a private server
2. Streaming music via Winamp
3. Streaming video 720, 1080 from pc to PS3 via the PS3 Media Server
4. DLing demos or movies on the PS3
5. Network streaming a movie from the Esata drives to the bedroom or kids rooms
6. Streaming video from abc.com or southparkstudios.com from the Cox cable modem
7. RDC over VPN to work machines
Now I have noticed that when I am streaming HEAVILY, from any 2 of the above mentioned, my network connections will simply stop working with a yellow exclamation mark on the task bar network icon after a few moments, nothing in the event logs, no logs or ANYTHING at all. It will simply stop working no notifications or anything poof, gone. I have EVERY single patch, driver anything I can think of installed. Nothing works, the timing is completely random. FYI I have a NETGEAR ProSafe VPN Firewall FVX538 with a cable modem connection on WAN 1 and a cellular connection on WAN2, these have no impact I feel on the connections because the PC may go down or the Netbook will go down depending on which one has the most load. So this simply tells me that it it not a firewall router problem as I have tried using a cisco unmanaged 24 port 1GB switch and I get the same problems. From analyzing the systems and layout I am led to believe that it is either a network adapter driver OR a Windows 7 problem (collisions, unhandled exception?), this NEVER happened with XP or Vista. I have tried everything but a new network adapter, I have tried the secondary adapter card on the mobo, I have tried bridging the two, I have tried daisy chaining the switch and putting each machine on its own dedicated switch linked to each other with no change. When the network goes down it is only that box effected, all other machines still connect to each other fine, only the one with load shuts down and the only ones that shut down are Windows 7. These machines are all wired with commercial cat5e patch cables, they have all been swapped for new ones lately. All networking and PC equipment are on UPS so I doubt voltage variations. Windows Firewall is disabled I only use the hardware firewall, I do not use any antivirus.
I am completely out of options, can anyone recommend a new route?
In addition when I go to the command prompt and attempt to do an ipconfig /release. I get an error saying that the adapter is not in a usable state. Very irritating, this forces me to reboot, or right click disable/enable on the network adapter. The right click route takes almost a minute to complete.
Tried update driver in nvidia control panel, no luck. I have also turned off the networking power saver option in the adapter settings.

Hi,
Considering this issue occurs on 2 different machines, I also think this issue may be more hardware related. You may also try the following:
1.    If the computers are connecting to a router, please ensure the router’s firmware is up-to-date.
2.    Please run the following command in an elevated command prompt in Windows 7:
netsh interface tcp set global rss=disabled
netsh interface tcp set global autotuninglevel=disabled
netsh int ip set global taskoffload=disabled
3.    Disable SNP in Windows 7 by setting Registry as following:
Note: Please perform a full-system backup first.
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters]
EnableTCPChimney=dword:00000000
EnableTCPA=dword:00000000
EnableRSS=dword:00000000
If the keys do not exist, please create them and assign the value.
An update to turn off default SNP features is available for Windows Server 2003-based and Small Business Server 2003-based computers
4.    If the issue persists, please add another network adapter to this computer and see how it works.
Hope this helps. Thanks.
Nicholas Li - MSFT
Hi, I'm experiencing a simular problem here.
My PC was using Asus P5Q-E motherboard but exchanged it for Asus P5Q TURBO Pro because it loses 'connectivity ' after an interval between a few hrs to 26hrs. During this state, I can't browse or my Outlook to check emails. The only thing that can send/receive data is Vuze. Plus, the strange thing is that the network icon says there's nothing wrong at all (when it obviously there is). Even the currency desktop gadgets says the time elapsed since it 'lost connectivity '.
I initially thought P5Q-E was faulty so now I'm using the TURBO Pro. However, the problem still persisted.
I am using Win 7 Ultimate x64 with all the updates and drivers. Connected via LAN cable to the router and the firmware is the latest. My ISP sent me a replacement router to confirm that their equipment is not faulty, which is true.
I have tried the above methods 1-3.
Although I'm not sure if I implemented Method 3 correctly since I don't usually go to the registry but here's what it looks like after creating it:
EnableRSS   REG_DWORD   0x00000001 (1)
EnableTCPA REG_DWORD   0x00000001 (1)
EnableTCPChimey REG_DWORD   0x00000001 (1)
There are 3 more PC's and 1 laptop in the house. 2 PCs use Win XP, 1 uses Win 7 Ultimate x64 and laptop uses Linux Ubuntu.
My PC has a second OS, Linux Ubuntu, I used it to time trial both motherboards (before and after switching) and found no problems at all even after 48hrs, so it confirms it's not a hardware issue.
The other PC's apart from mine are connected wirelessly. As far as I've been told, they don't experience the same issue I have.
I've been trying to tackle this problem for months now and I'm frustrated to reboot my PC every time it 'loses connection '.
I chatted with Asus about the issue when I still had the P5Q-E mobo, they said that they built a simular system to mine with the same mobo and said they couldn't reproduce the problem I'm having. THey even tested on other mobos with the same LAN chip and found nothing wrong. That's why I got the TURBO Pro that has a different LAN chip.
Anyone got anymore suggestions???
Thanks in advance.

IPhone 4 stop working with ios 6.1

iPhone 4 stopped working with ios 6.1, visited apple first time, restored phone and worked, less than 24 hours later stopped working again, back to the store, I told iPhone is out of warranty and they'll replace for $150. iPhone worked fine with previous version, no problem at all. Asked to restore to the previous software version, told can't be done. Why should I pay for a damage caused by a software update. Tec claims that ios 6.1 will not work with my phone because it discovered some hardware malfunction, possible the home button. They can't repair. suggested to go to a third party. I'm a satisfied Apple product user for many years. What happened? Any welp out there?

Hey.. I have had this issue since yesterday afternoon.. Some people are saying to keep restoring again and again until it finally goes through.. I have done so like 10 times on my MAC and then I used my husband's PC and tried it 4 times.. No success.. I called apple support, but no help came from there at the end, and the only thing they were able to suggest to me is to sell me a new phone just like mine for a discounted price.. **** NO
Anyways after about 18h of search and stress I came across this link:
http://techglobex.blogspot.com/2012/06/downgrade-from-ios-6-beta-firmware-to.htm l
That will only make it possibe to go backward.. You will end up back with the IOS 5, but at least you will have a working phone and it will bring back all your contacts and everything else that you ever had backed up on icloud and on your computer. There might be descripencies with the Applications but again this is an issue easily solved, you can always download them back.
Two more things: One, you do not have to download the old version of the itunes, the newest version worked for me without any issues
When choosing to download the older IOS 5.1.1, you will need to figure out whether your carrier is GSM or CDMA but you can easily google this info online..
Well hope that will work for you like it did for me

Home sharing does not work with new mountain lion update.

home sharing does not work with new mountain lion update. Does anyone else have the same issue. Updated all computers in my home, deauthorized and reauthorized each computer. turn off home sharing and turned it back on. don't know what else to do..please help...

Our Apple TVs continue to lose connection ever since installing Mountain Lion on the host computer. The only thing that fixes them is to quit and relaunch iTunes, which only works unti the ATV goes to sleep. If a movie is paused for more than a few minutes and the ATV goes to sleep, pressing play again on the remote is greeted with "There are no movies on this computer" or "Turn on Home Sharing."
If we stop a video on one ATV and attempt to resume it in another room, the error begins again. The other ATV can't connect until iTunes is relaunched.
My guess is that it has something to do with the new [annoying] security settings. But I still haven't found a fix other than restarting iTunes everytime we want to watch something from our downloads. Fail.

Network Extender stopped working with new FIOS Quantum router

Similar Messages

Maybe you are looking for