Network Info needed
I currently run a new iMac on my network through the built in wireless. I have just got a Powerpc G5 power Mac that has no wireless and i wish to move it away from my BT home Hub router so no network cable available to far to re-route. It has no built in wireless and i wish to know can i connect it through the iMac and share its broadband and also transfer documents using a Ethernet cable connection. can you give me details of what i need please i think i remember that to connect 2 computers i need a cross over network cable any help will be great.
Hi Shylock1966-
This may be helpful: Mac OS: Connecting to the Internet and sharing files locally at the same time
Luck-
-DP
Similar Messages
-
My ipod keeps searching for network, even when the network info is all set properly. It has suddenly started doing this. Also, buffering forever... I have tried to reset the network few times, but not working.
Hello Nazer_502,
I would be concerned too if my iPhone was acting this way. It sounds like it is overheating and not holding a charge. I recommend following the steps listed below when experiencing an issue like this:
Battery life seems short
Click ( www.apple.com/batteries/iphone.html) for tips on how to prolong iPhone's battery life.
Try turning iPhone off and then on again.
Connect iPhone to iTunes and restore iPhone.
If the screen shows a low-battery image, the battery is low on power and needs to charge for up to ten minutes before you can use it.
When charging iPhone, make sure to leave it charging until it is fully charged. You'll know the battery is fully charged when the battery icon in the upper-right corner of the screen looks like this .
Note: When charging using a computer, don't connect iPhone to a keyboard. Also, the computer must be turned on and not in sleep or standby mode. If iPhone is connected to a computer that's not turned on or is in sleep or standby mode, the iPhone battery may drain.
You can find the full article here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I'm coding a cellular phone program. It needs low level network info, idealy it would be a CellID that it is connected to.
The main problem is to know if two phones ar in the same area without using location ('cos it is a relatively new api and here in argentina time will past until location phones are here ).
The simplest thing i imagine is to know the cellid where the phone is connected and match in a server what phones are in the same cellid. I was looking for a low level api or something to use AT commands in the phone but i can't find nothing.
If you know any way to acces that info or the AT commands please respond.
If you know other way to know if two phones are in the same area, please let my know.
When i say "same area", i mean like 20-30 milles (50km) from each other, more or less, it dont need to be accurate.
Thanks in advance
LoskyThis seems to be a bug. When a transformation (to 3785, 3857) is involved it seems to query the whole table to build up the cache. Will investigate further to see if caching=none makes a difference.
-
I my mac wont recognise my password, i have tried to reset password using single user but my mac wont stop at single user it just continues to root, how do i get it to stop at single user so i can add info needed to reset password?
Are your sure that wasn't a Verbose boot (Cmd-V) you were trying? That would go on to a regular boot.
Try a PRAM Reset, then try the single user, Cmd-S, at the startup chime. For the PRAM Reset, hold down Option - Cmd - P - R all together until it chimes a total of three times, then let go to finish booting. -
The program would enter info for me. I only had to type the first letter or number of the info needed. For example, my first name is OSCAR. So, to enter this info in the box marked "First name", I only had to type in the box the letter "O". The program would then type OSCAR. I would then click on the name "OSCAR" and the name OSCAR would be entered in the box asking for my first name. Same with "city", "zip code", "last name", "email address", etc. Is this a Firefox feature??
That feature would be provided by an add-on for Firefox. The most popular add-on of that type was the Google Toolbar for Firefox, which has been discontinued by Google for Firefox 5 and future versions. <br />
http://googletoolbarhelp.blogspot.com/2011/07/update-on-google-toolbar-for-firefox.html
There are a number of different '''"auto fill"''' add-ons that are available from other developers. Look at this search for one that meets your needs. <br />
https://addons.mozilla.org/en-US/firefox/search/?q=auto+fill&cat=all&x=0&y=0 -
I bought a used macbook air, it didn't come with the flash drive to do a factory reset. Can I download the info needed and save it to my own flash drive and then do a factory reset? If not what can I do?
If it originally shipped with Mac OS X 10.6.8 or earlier, click here, phone Apple, and order a replacement.
If it originally shipped with Mac OS X 10.7 or newer, restart it with the Option, Command, and R keys held down.
(113079) -
Info needed to produce a Docking Station for iPhone 5
Hello,
Where can I get the info needed to produce a Docking Station for iPhone 5?
I mean technical details (e.g. for Lightning connector) and legal issues.
Thank you!https://developer.apple.com/programs/mfi/
-
Could not find network adapter needed for registration
Cisco IP Communicator has worked well for a month now. One morning I go to launch the app and I get the error message: Could not find network adapter needed for registration. I rebooted my pc and I got the same result. I reinstalled the app and got the same results. I don't know what if anything changed, but I know I can't even get the application to load to look at any settings. PLEASE HELP!!!
Brian CHi Brian,
Have a look at this good thread :)
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&topicID=.ee6c829&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc0bb6f
Hope this helps!
Rob -
Our apple tv keeps saying network time needs to be set
We have been trying for an hour to get our apple tv to work. Network is up
, signal strength is strong bit we keep receiving message "network time needs to be reset". We have used it for over 2 years without fail.Welcome to the Apple Community.
Assuming this is not the first time you have used your Apple TV
You might try restarting the Apple TV by removing ALL the cables for 30 seconds.
Also try restarting the router.
If the problem persists, try a restore, you may want to try the previous procedures several times before doing this.
If this is a new Apple TV, it may also be that your network router is not allowing access to the timeserver, check that your router allows access over port 123. -
Portege R700 PT311A - Network Adapter needs to be installed
My Toshiba Portg R700 (PT311A-06600Q) will not connect to the internet.
It says that a Network Adapter needs to be installed and configured, but I do not have the disc to do this, nor do I have an internet connection on my laptop to download the driver.
I have attempted to download the driver onto a USB, using another laptop, then using that USB, I have tried to install it onto the problem computer, but it won't install.
There is no Windows installed on the problem computer, may this be an issue as to why the driver won't install?
Help me, please!Hi
I hope you picked up the right driver.
Not quite sure if you are talking about LAN driver or WLan driver and what Windows system you are using but fact is that all drivers for this unit can be found here:
http://www.mytoshiba.com.au/support/download
I would recommend you to check once again if you downloaded the proper driver. Then move the driver package to the notebook (desktop). Unzip the package and execute the setup or install exe file.
In case you would not find any exe files in the package, I would recommend you to install the driver within the device manager. -
"Account Info Needed" and Calendar entries disappear
This is a side problem in conjunction with the perpetual "Install Update" problem (see here: http://supportforums.blackberry.com/t5/BlackBerry-Link/10-1-0-4181-won-t-stop-trying-to-load-and-now...
The BBQ10 device stops connecting to my desktop Outlook (calendar, contacts, tasks)
Symptoms:
Calendar entries disappear after a simple screen refresh.
"Account Info Needed" keeps repeating.
When updating the Account, this error appears: "There was an unexpected error and the operation was canceled"
The only way to temporarily fix this is to delete my account on the device and recreate it. I've done that three times just today. The data comes back fine then disappears again.
Any tricks on making the account stay put?It's been 24 hours with neither of these 2 symptoms occuring. What did I do? I deselected the "Turn on wireless connections to my computer".
Wth the bluetooth still enabled, my PC connects to the device as a storage device (which is all I really need for data/file transfer anyway). The Calendar entries are perfect - back and forth.
I'd be interested in hearing from others if this helped them.
(NOTE: the DPC_WATCHDOG_VIOLATION BSOD still happens when the device is connected to the PC for any time longer than the backup or sync. That's an altogether different issue.) -
Cant acess itunes store or home sharing on apple tv 2, keeps telling me that network time needs to be set. When I go to time zone section on apple tv - I chose a city...but still no luck. Apparently, can't do anything without the time being set. How do I set this up?
Yes, I did (turning off and then on again is a way of life for any windows user!). Actually, through a process of trial and error I have fixed the problem although I'm not very comfortable with the fix. For some reason, the OS X firewall is to blame. By relaxing the firewall settings to their most lenient, the iTunes store is now fully accessible via iTunes, and so is the whole of the apple website. Another added side effect has been that general web browsing is now lightning fast.
I'm therefore left with the (temporary) conclusion that my iMac's internal firewall is only capable of blocking access to the web resources of the people who created it, and slowing my web browser to a crawl. -
I'm taking iPhone 3G OFF NETWORK but need to TRANSFER the SMS messages to iPhone5. How do I do this?
right i rang orange and they said they can do it
so two days later (today) i got a text saying the tried to take payment but i didnt have any credit on my phone so they will try again in 24 hours,
ive topped up now and i also turned off cellular data off to stop my phone using any credit, will this cause any problems with unlocking if the cellular data is off? -
HT5035 Why is my credit card info needed if I have an iTunes balance?
Why is my credit card info needed if I have an itunes balance?
It is part of the Verification process.
To Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact -
How do I shut off my Apple TV at the end of use. It asks me if I want to sign off but I assume that if I do this I will have to re enter my network info as well as pass word when I use Apple TV again
Just leave it be and after a period of inactivity it'll automatically shut off, press a button the remote and it'll wake up.
Maybe you are looking for
-
My MacBook Air is not allowing me to see myself and others during gchat. The little light beside the camera goes green, so it's working but I still cannot view anything. I have used the camera and computer for gchatting with no problems previously. T
-
OC4J 9.0.2.1.0
Before you say "your still on that version????", yes we are and there is nothing i can do about it for the moment. I've recently put together an app with J2EE1.3 (oc4j 10g) and have been trying to downgrade it to J2EE 1.2. So far the app is in a depl
-
Why do we need serializable?
Hi, I read from the book about serializable, object has to implement serializable interface in order to get transferred across the internet. But I remember that I can use socket class to create a TCP port and transfer plain text across the internet;
-
Bug? - trouble with iPod menus
I recently downloaded my first video podcasts, but I'm having some trouble playing them in my iPod. Although they are ok when played in iTunes, they didn't seem to be recognized as video by the iPod - at least when I selected them through the podcast
-
I have a MacBook Pro and a HDMI cable which once did work, but no longer. Did software change, did my luck run out? What can I do to make HDMI cable work again?