Network interface and usb device not working.

hi everyone,
I just installed Solaris 10 3/05 S10_74L2a x86
on my home pc.
My motherboard comes with an in-built ethernet port for networking.
But after installing the OS, I can't access to the Internet (I logged in as root).
Then I do an ifconfig -a command, I see only the loop interface, my ethernet port interface connected to my modem is missing.
I also try to plug in a USB flash drive into my USB port but I cannot see what is inside my USB flash drive.
I have done a devfsadm -v command for that added USB flash drive.
anyone knows what go wrong?
any help given will be greatly appreciated.
thank you.
good day :)
szehanz

But after installing the OS, I can't access to the
Internet (I logged in as root).
Then I do an ifconfig -a command, I see only the loop
interface, my ethernet port interface connected to my
modem is missing.Maybe your ethernet driver is loaded but not attached.
Check device name with prtconf and see if your device
is in /etc/drivers_aliases or not.
I also try to plug in a USB flash drive into my USB
port but I cannot see what is inside my USB flash
drive.I had the similar problem before. First, check USB
ports are "alive" (see ehci, uhci, ohci are correctly
loaded and attached). If it's ok, insert you USB flash
drive and restart vold with "pkill -HUP vold".

Similar Messages

Dual-Boot; Restart and boot other o/s USB devices not working

I have issue with my msi z97-g43 mobo and Windows dual o/s PC.
Booting with win-8.1, USB devices working very well.Restaring windows 8.1 have NOT any issue.
After shutdown & start PC, choosing to boot windows 7 on bootmanager, USB devices not working in Win-7.
System no hang or occur any error/BSOD message.All startup programs run as normal.
I tried to re-plug usb devices but notting happens... Still not working
But after the win-8.1 shutdown, if i switch off PSU power button, watting ~1 munute for discharge.
After power up PC and boot with windows 7 all usb devices works normaly.
I checked all internal connections. 2 times disassembly all hardware and re-built system, nothing changed.All windows updates and latest drivers installed.
I'm sure other H/W is OK, but I thnik this mobo have a fault.

Thank you for reply.My PC system specs:
CPU:    Intel Pentium G3258 3.2ghz
Board:    MSI Z97-G43 /Bios: Ver. V17.7
MEM:    G.Skill Ripjaws 2x4gb DDR3-1600mhz cl9 1.5v F3-12800CL9-4GBRL
VGA:    Sapphire AMD Redeon HD6670
CASE:    Zalman z3 plus white (5x 120mm fan)
PSU:    Thermaltake Litepower 500w (12v1+12v2=36amp)
HDD-1:    Seagate 1TB ST1000DM003 /HDD-2: Seagate 2TB ST2000DM001
COOLER:    Akasa 92mm PWM Blue Led
OC:    CPU:Default /MEM: X.M.P mode=1600mhz 9-9-9-24-2t 1.5v
O/S:    Win7 x64 PRO + Win8.1 x64 PRO (Genuine)
All hdd's have MBR based partition table.Windows 7 & 8.1 installed in non-efi mode.In BIOS Boot sequence is setting up to non-efi Boot(system) drive as primary.
Before I suspect maybe have a short circuit to pcb or similar thing cause this issue.I take out all parts outside the chassis, and ran this system on the antistatic bag and box.Nothing has been changed.
I have Cooler Master Devastator(MB24 + MS2k) USB keyb+mouse set and tplink wn722n usb wireless dongle.
I have one more pc,based on AMD 970+SB950 chipset mainboard and AMD CPU.I exchange all parts to this amd mainbaord and tested for faulted hardware.All intel system H/W's is ok.All works great
Dual boot works perfectly.Not needs to switch off psu/power back and run system again.
I think msi z97-g43 mainbıoard have a problem.

I have an Ipod Touch, it appears inactive and says conect to Itunes. When I connect it to the PC, the PC says "USB device not working". How can do to solve this problem.

I have an Ipod Touch, it appears inactive and says "connect to Itunes". When I connect to the PC, the PC says "USB device not working". How could do to solve this problem?

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
or
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

Iphone 4S will not charge, error that USB device not working, found any suggestions?

iphone 4S will not charge, error that USB device not working, found any suggestions?

Hello Chambless,
The troubleshooting steps below can help get your iPhone to charge.
If your battery doesn't charge, or if your device shows a low-battery image, black screen, or "accessory not supported" alert, follow these steps.
Inspect the connector at the bottom of the phone:
Make sure that there are no bent pins in the connector.
Make sure that the connector is free from debris.
If there are bent pins or debris, please contact Apple Support.
Otherwise, continue troubleshooting.
Make sure that the outlet you're using works.
Make sure that the Apple USB cable and Apple USB power adapter work.
Plug the device in to power and let it charge for up to 30 minutes. If you don't have an Apple USB power adapter, try connecting to a computer's high-power USB 2.0 port (not a keyboard). The computer must be on.
If the device still exhibits an issue, try turning your device off and then on again while connected to power.
If the issue is persists, please contact Apple Support.
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Cheers,
Allen

Usb devices not working after 2.6.38 kernel upgrade

Hello everyone,
today I've upgraded my aur system to the latest packages version , kernel 2.6.38-2 .
After the reboot the usb keyboard doesn't work at all , as the usb mouse, leaving me struck at the login screen .
If I try to modify kernel boot parameters in grub or in a live distro (sysrescd) the keyboard works flawlessy .
Any clue ?
thanks in advance

I just updated to 2.6.38.7-1. The USB devices that I have plugged in before booting work (e.g USB headset). If I try to insert a new USB device, it isn't recognized. Flash-disks and USB mice that worked under the last kernel aren't working at all.
Is there a command that lets you "turn on" a USB device, or force the kernel to recognize it? I tried messing around in /sys/bus, but even in the root shell, I got "invalid write" errors.
Interesting snippet from dmesg;
[ 19.399041] uhci_hcd 0000:00:1a.0: PCI INT A disabled
[ 19.399447] uhci_hcd 0000:00:1a.1: PCI INT B disabled
[ 19.412940] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[ 19.413381] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[ 151.340126] uhci_hcd 0000:00:1d.0: PCI INT A disabled
Here's where it finds my webcam;
[ 9.626704] usb 2-5: new high speed USB device using ehci_hcd and address 3
[ 10.381678] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-5/2-5:1.0/input/input15
[ 10.381759] usbcore: registered new interface driver uvcvideo
.. and where it finds the mouse I had plugged in (you can see me disconnect it at entry 148);
[ 10.490045] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 11.201856] input: Dell Dell USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input16
[ 11.202001] generic-usb 0003:413C:3012.0001: input,hidraw0: USB HID v1.11 Mouse [Dell Dell USB Optical Mouse] on usb-0000:00:1d.0-1/input0
[ 11.202017] usbcore: registered new interface driver usbhid
[ 11.202019] usbhid: USB HID core driver
[ 148.846756] usb 5-1: USB disconnect, address 2
When I try to reconnect the mouse, nothing happens. You can see that the kernel has this error repeatedly;
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
Edit: Found a temporary fix*.
# cd /sys/bus/usb/devices/
# for device in usb*; do echo "on" > $device/power/control; done
* I'm not responsible for what happens to your devices when you run this, but it worked for me. Check out: http://www.mjmwired.net/kernel/Document … gement.txt
Last edited by vkumar (2011-05-28 04:28:05)

MACBOOK USB device not working in WIndows XP

My MACBOOK USB devices is working fine in leopard OS(10.5.1) but in windows XP professional the USB Devices is not working after I did dual boot.Please help how would I fix the problem.
Thanks
Mike

Please try the above procedure first as mentioned by SilentFlyer. If that does not work then highlight My Computer and Right Click on mouse. On the menu that pops up Choose Properties. Click on the Hardware tab and then Device Manager. Scroll all the way down to Universal Serial Bus Controllers. Click on the little plus sign to the left to open the sub-components. Does any one of them have a yellow exclamaation mark? That indicates that something is not functional. Please let us know what you see there.
Axel F.

Touchsmart TX-2 fingerprint scanner and USB ports not working

Hi everyone,
Please forgive me if this is in the wrong spot.
Just sent my laptop (Touchsmart TX-2 1015au) off for a warranty fix - told them the USB ports weren't working on Windows 7, 64 bit. It came back wiped, running on Vista 32 bit and.....with the USB ports not working.
I figured I'd try to get it working because I need my laptop for uni and can't send it back right now. So I clean installed Windows 7, 64 bit again and its still not working. Did the standard open device manager and uninstall everything under the usb tab. All that has resulted in is causing the fingerprint scanner to stop working (being told that it is not connected) and still no working USB ports.
All advice really welcome and very much appreciated!
Thanks in advance

Hi:
Should be no problem to get W7 32 bit to work on that model.
Just use all of the drivers and software from the HP Probook 450 G0 on your model except the Audio, BIOS and firmware files.
Your model uses the Intel HD graphics driver only.
The first driver you have to install is the Intel chipset installation utility and then reboot.
http://h20565.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&lang=en&sp4ts.oid=5359407&ac.ad...
Audio: Accept the agreement. Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownT...
If for some reason, the Intel HD graphics driver from that model does not work, then use this one...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23713

MACBOOK USB Devices not working in Windows XP

My MACBOOK USB devices is working fine in leopard OS(10.5.1) but in windows XP professional the USB Devices is not working after I did dual boot.Please help how would I fix the problem.
Thanks
Mike

This forum is for troubleshooting the usage of OS X, not Boot Camp for Windows.
You'll want to repost your question in the Boot Camp discussions:
http://discussions.apple.com/category.jspa?categoryID=237

Wifi hot spot and USB tethering not working

I updated my both Lenovo a 7000a phones to Bulid Number A7000-a_S144_150721_ROW today, Since then both of my phones stopped Wi Fi Tethering and USB Tethering.Base Band Version A7000.ROW.V15,2015/07/21 20.44I would like to mention further that Both the Wifi Tethering and USB tethering were working fine before the update! This is in contrast to the Previous bug found in S 142 version! Now devices are being connected but with limited connectivity.Please comment for a solution!

I would like to mention further that Both the Wifi Tethering and USB tethering were working fine before the update! This is in contrast to the Previous bug found in S 142 version! Now devices are being connected but with limited connectivity.

Installed Windows & 32 Bit But Drivers and USB ports NOT WORKING.

I bugh an HP Pavillion TS 14 Notebook that came preinstall with Windows 8.1 64 bit which I hate so wiped the drives and installed Windows 7 32 bit and now I have a big problem. None of my network drivers work and the 2 uSB ports where I plug my mouse and other SB hardware in no longer work.
I did a back up of the SW Set up file that has all of the HP dvers for my laptop but both the network and video divers won't install. And When I try to install the drives I get the eror message saying they are not compatible with this version of Windows.
I have loked on the HP website under my laptop model which s as above but HP don't do drivers for Windows 7 32 for my laptop. And I have looked on both the Realteck website for both the Realteck ethnet and Realteck wireless network drivers but none of them work or install on my operating system. The video drivers Intel don't work either. So I am really stuck a I cannot go back to Windows 8.1 as though that 32 bit Windows 7 would work on my laptop but most of my drivers are not compatible with the operating sytem And I don't want to install 64 bit Windows as I like 32 bit.
The drivers that are not working on Windows 7 32 bit are:
Realteck RTL8188EE 802-11b/gn witeless lan
Realteck ethnet die and
Intel High definition graphcs driver
Which don't work at all on Windows 7 32 bit as they are 64 bit only drivers.
So can you please post me a link bth the network and Intel graphics drvers that work with my laptop. As I have tried lots of different Realteck and raphics drivers for Window 7 but NONE of them work on my system. And None of my USB ports are working either. So how do I solve this problem?
This question was solved.
View Solution.

Hi:
Should be no problem to get W7 32 bit to work on that model.
Just use all of the drivers and software from the HP Probook 450 G0 on your model except the Audio, BIOS and firmware files.
Your model uses the Intel HD graphics driver only.
The first driver you have to install is the Intel chipset installation utility and then reboot.
http://h20565.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&lang=en&sp4ts.oid=5359407&ac.ad...
Audio: Accept the agreement. Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownT...
If for some reason, the Intel HD graphics driver from that model does not work, then use this one...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23713

Macs and USB Devices Not Getting Along

I am posting this incase I'm not the only one.
I have noticed this issue with my Intel iMac as well as my PPC iMac
Both are running the latest versions of OSX 10.4.9
This is regarding USB connectivity and the effect connected devices have on the system.
USB Setup
1 7 Port usb hub
1 Palm Dock Connected via hub
1 iPod Dock Connected to 2nd USB Port on iMac
1 ScanSnap connected via hub - POWER OFF
Bluetooth Apple Mouse & Keyboard
1 TomTom 910 connected via hub - Connected to dock but power is off.
1 Canon IP90 Connects via Bluetooth - POWER OFF
This is what happens.
If one of the following usb devices is connected, boot times can be extended with the system "pausing" at the Gray screen before Gray Apple Logo appears.
iPod
Palm TX
Once the OS boots Missing Sync's Menu Bar status application will not load, will have to manual load app.
If I disconnect these devices and reboot boot time is normal with no "pause" and missing sync loads normally.
Also i Have noticed my Apple keyboard will take longer to pair during boot with or without these devices connected.
iMac will not power down as scheduled with these usb devices connected if the system falls asleep with them connected.
Normally the iMac will wake itself up at 11pm to shut down. If my iPod or Palm is connected it will not. It will only shut down via schedule if it is awake when scheduled time is reached.
iMac G5 2 Ghz 1.5 Ram 400 Gig HD & iBook G4 1.33 12 Mac OS X (10.4.6)

So just an updated to my original post. I have been working with tech support for Missing Sync. There is a known issue with a menu bar application that comes with their software. It seems when more than 1 or 2 usb devices are connected this menu bar app doesn't load correctly... or at all.
According to them.. one of their techs actually spoke with a Apple Engineer at WWDC this week regarding the issue. According to this Apple Engineer there is a known issue with OS X and USB handling. Apparently the OS can "freak out" if certain devices are connected during boot.
No other specifics where given, and who knows if this is Missing Syncs attempt at shelling off responsibility to Apple. However, I am inclined to believe it as I have noticed that my iMac Intel or PowerPC will take a significantly longer time booting if my iPod or Palm Pilot is docked during boot. I've also noticed I can't reset my PRAM when these devices are connected.
I hope apply addresses these issues, seems kinda crazy its gotten this far being that USB devices are the primary method for expanding your Mac's abilities.
iMac G5 2 Ghz 1.5 Ram 400 Gig HD & iBook G4 1.33 12 Mac OS X (10.4.6)

USB Devices not working on cold boot

On a cold boot, I get either my mouse (Microsoft Optical) or my modem (see signature) not switched on. If I reboot, or just re-plug them in, they switch on and Windows detects them. The modem is attached to a port on the mobo, and the mouse to a powered USB hub. The only other device powered at boot is a joypad (Thrustmaster Dual Power 2), which always works at boot. Devices switched off at boot are a printer/scanner, desktop light, and an extension lead for a thumb drive.
Does anyone have a solution to this?

Quote from: artur.aragao on 13-February-05, 11:59:04
Expensive friend,
Step for the same problems, where already I communicated diverse times with the support of the MSI not obtaining a definitive solution for this problem. It does not go to advance nor to make magic, therefore the problem has left of the plate-mother and not of the operational system. I have one mouse of the Microsoft who possesss led and when I give the departure in the PC the same does not light in the screen of informs of devices of the CMOS. It would have.
Then I am obliged to remove and to place mouse of the door usb so that mouse functions. The problem is that I have that to faer this almost all time that I bind the micron.
The bios beta that decided this problem palliative were 1.5B8.
I see that all the ones that pass for this problem are receiving the had respect, therefore this problem already is old and no solution was adopted until the moment for the manufacturer.
If my problem to continue, I will get rid myself of my plate and I will migrarei for another manufacturer who hears me and she respects me, therefore we make many times investment s in products that would not have to give as much migraine.
We buy TVs and DVDs and we do not pass for problems as these.
I was disappointed with the MSI in this part. It would go to acquire a VGA 6600GT, but today I think seriously about not buying more nothing of the MSI.
Still more for that it occurred with the 6800GT that were being sales and in the truth they were 6800NU.What it is this?
I advise to the friend who if not to decide its problem in at least 1 month, it speaks brazenly of its mainboard and it buys of another
manufacturer as the ABIT or same Gibagyte.
I have friends that they possess plates of the Gigabyte and are very happy.
Artur de Souza Aragão
HUH??? You did know this is an English languager board right? If not then please read the forum rules. Also note that hijacking someone else's post so you can complain is against the rules here as well.
This is entirely a user to user forum and as such MSI is not here nor do they read it. So yopur complaints whatever they may be as we can't entirely read your post is not getting to those folks that you want to complain at. Instead you are just making the rest of us upset for no visable reason. If you want to contact MSI to copmplain may I suggest a phone call. You may also want to call someone there that actually speaks the same language so there are no miscommunications as what is happening here.
Edit - his posts on this subject were all removed due to spamming the forum.

AE 2220 - USB Devices Not Working

My AE 2220 will not properly mount and access USB devices in any of the USB ports. I've unsuccessfully tried to use three different thumb drives and a Sony camcorder and experimented with every available USB port. The AE 2220 is running the factory default Windows 7 installation. AFAIK, USB devices never properly worked. Not sure what to do from here.
Here are some symptoms I see after plugging in USB devices:
Status bar appears as the device is being read/recognized and the status bar freezes. Other times the status bar moves quickly at first, then slows to a crawl. Sometimes the bar gets to the end and starts over in an endless loop.
Sometimes a message box appears stating that the USB device is damaged (which it is not) and asks if I want to repair the device. Clicking "Yes" does not fix anything.
On some occasions the device mounts, but when I try to copy files to the desktop the copy freezes and hangs and I have to unplug the device and quit the process.
Can someone please help.

Hi,
In addition to some group policy issue as Balaji Kundalam suggested, there should also be some permission problems.
We could run gpresult /r to check which policy that might have effect on this issue.
And for the permissions, we may take a look at the following thread:
External Hard Drive "is not accessible. Access is denied."
Best regards
Michael Shao
TechNet Community Support

Both internal and USB mics not working

Hi there, all. Long-time lurker, first-time poster. Starting last night, I have been having issues with microphone use on my iBook G4. Neither the internal mic nor my USB headset mic (Altec Lansing AHS302USB) are accepting input.
The internal mic's failure doesn't surprise me, as I have heard about the delicate nature of the wire connecting the internal mic from its position on the display down to the main computer. It's the USB mic that confuses me, since USB mics are what everyone seems to recommend that people use when the internal mic is on the fritz (thanks to other mics not working with Mac due to the line-in thing). Also there is the fact that I have used this headset with this computer for over a year with no significant issues until now, with both mics simultaneously failing.
There doesn't seem to be a problem with the headset's wires; I am still able to hear audio through the headphones quite well, and when I load my audio recording program (Audio In) and Sound Preferences, I can see the occasional blip of sound recognition when I move the USB adapter portion around in the port. These blips even occur when the pink microphone jack and headphones jack are unplugged from the adapter, so this suggests to me that the problem lies not with the wires, but somewhere in the USB adapter, port, or the computer itself.
I'm leaning toward the computer itself, since it just seems odd that both mics would just happen to stop working at the same time. That and the fact that audio output still works through the headset, and the USB ports work fine for other USB devices such as my external drive and iPod.
I have tried restarting, resetting the PRAM, and repairing permissions with Disk Utility. Nothing's working so far.
Does anyone have any idea what could possibly be wrong?
For reference's sake, I took a recording of the sound that results from jiggling the USB headset adapter in the port. It's very quiet, so you may need to turn up the volume a little bit to hear it. Again, these are the ONLY sounds that the mic is able to pick up currently.
http://animeutahime.com/temp/faultymicrecording.mp3
iBook G4 Mac OS X (10.4.10) 768 MB RAM, 37.7 GB hard disk

Just to chime in here - I wonder if it's down to the software: I've recently updated to 10.4.10, and the internal mic seems to have stopped working.
One positive effect of the change to 10.4.10 is that my Griffin iMic no longer flips to 8-bit, 22khz recording when I plug it in.
Having said that, I really like to get my internal mic back up and running again.
iBook Mac OS X (10.4.10) 1.5gb RAM, 60gb hard disk

Why is my Intel iMac restarting randomly and USB keyboard not working randomly?

My intel iMac has been randomly rebooting itself without any error messages. It also seems to coincide with the keyboard (USB) not working, but not always. At first, it seemed to happen right after waking the computer from sleep, but now it happens when I am just sitting at the computer about once or twice a day. For now, i have temporarily removed all external devices (except time capsule) and disabled any bluetooth or iTunes synch'ing over wifi. I have also disabled all power management features.
I've tried different keyboards and resetting the SMC. Could bad memory cause this?

Could be anything from a loose power cable, to loose or bad RAM module.
1. Check all your power connections, including the mag connector on the back of the iMac.
2. Reinstall the RAM modules, as per > iMac: How to remove or install memory. When installing new or reinstalling RAM, be sure to push firmly on each module with both thumbs to insure that they are fully seated in the slots.
Then if it is still acting up...
3. Run the > Extended Apple Hardware Test

Network interface and usb device not working.

Similar Messages

Maybe you are looking for