Network is down suddenly on my Solaris X86 box

Hi all,
I have been using Solaris X86 for a while. However, I found a strange problem when downloading large/many
files with FTP. For example, I ftp to my Solairs X86 box and try to download all my backup software to my local
notebook or PC. After about 10 mins, Solaris X86 box's network will be down suddenly without any error or
warning message.
I found this problem from Solaris8 to Solaris9 and the FTP server daemon I used included NcFTPd, vsftp and
even the default FTP daemon. I have tried two different hardwares. The only one possible reason is my
network (Intel 100 ServerPro something).
Does anyone have such a strange problem when downloading many/large files from your Solaris X86 box?
I also check the log file but found nothing.....:-(
Thinking to switch FreeBSD/Linux box for my FTP service. Please advice and thanks first!
Hsinan

This bug is common to the Intel Server 100 MBit Cards
The problem occurs on high net load.
You have to reboot to restart the card, since it is a complete
stop of the card.
You can try to put the card into another pci-slot, but this helps
only in rare cases.
I had to replace the card with a 3com 3c905b to have uninterrupted
transfers.
The Inteldualport cards seem to work to.

Similar Messages

Solaris x86 with card on-board

Hi all,
I got a problem when installing Solaris9 x86 on ibm NetVista Machine.
I have installed 2 other machines with separated network card sucessfully. I can configure to connecto to my LAN network.
But when install on 2 ibm NetVista machines (which include onboard network card ), It is fail to be configured to connect to the network in both following cases:
Case 1: I choose proper driver as Sun suggest for Intel VE Pro(R) 10/100 : iprb. And the Solaris detect successfully. I checked by "ifconfig -a" and saw the network card active on "iprb0".
Next, I following correct instructions to configure the network card to connect to the LAN. But when i ping IP (9.187.186.18) to other computer in our same subnet LAN,
The system display eg: "No anwer from 9.187.186.18"
I run the "snoop" command to view broadcasr ARP in an other terminal. The snoop terminal displays ARP signal boradcasting from the Solaris. However, it can nerver get ARPs from other computer in LAN.
Case 2: I add 3COM network driver to the solaris ( onboard card is no loger used ). The system can auto-detected this card and i can configure to connect to the network. The problem remain unchange.
Is there any special in IBM Netvista machine need to be configure under Solaris x86 or any particular configuarion for on-board network card. ???
Can any boy help me to solve this problem ??
Best regards,
Thang,
Vietsoftware Developer

However, it can nerver get ARPs from other computer in LAN.Are you perhaps running "snoop" on a box different from the one that you're trying to ping, and are you using
a switched ethernet? In that case it would be OK if you only see the ARP broadcast, because the ping target
box will send the ARP reply directly to the MAC of the requesting station (i.e. there's no ARP broadcast reply),
and an ethernet switch will send the ARP reply directly to the port where the station with the given destination
MAC is connected - no other port should see the reply.
If you're trying to ping 9.187.186.18 from the new Solaris x86 box, try to run snoop on the 9.187.186.18
system. 9.187.186.18 should see the ARP broadcast from the LAN, and the 9.187.186.18 box should list the
ARP response it sends back to the LAN.
Is there any special in IBM Netvista machine need to be configure under Solaris x86 or any particular
configuarion for on-board network card. ???I guess the interrupt handler for the NIC is not working, so the Solaris x86 sees no incomming packets.
See the "troubleshooting" section on the following page:
http://solaris-x86.org/documents/tutorials/rtls.mhtml

9ias 1.0.2.2 on solaris x86

is there any port to solaris x86 box for oracle 9ias 1.0.2.2?
thanks
ckh :)

Hi,
I tried to install Oracle 8 on Solaris 8 for X86. When running runInstaller script, it met the error "Syntax error at line 1:'(' unexpected".
Please help me!
Thanks

Please suggest the fastest way to install Solaris x86 PC 30 boxes

I've already tested one and it's successfully installed.
I have to install 30 boxes , all are same spec.
Please advise the fastest procedure to install.
Note : There is no sparc machine.

Only problem with imaging a Solaris x86 box is that your machines will end up with the same hostid (which is pseudo-randomly generated at Solaris installation time for x86). This may, or may not, be a problem, depending on what commercial software you use...
To avoid this, you have to use jumpstart, or do some serious hacking.

Mounting a Solaris x86 CD/DVD from a remote Windows CD/DVD-ROM drive

Greetings, all.
Is it possible to mount a remote Windows CD/DVD-ROM drive? I have the Solaris 10x86 Companion Software DVD sitting in a CD/DVD-ROM drive that's installed on a Windows server on my network. It is shared-out (F:) and the two servers can ping each other. I've also confirmed the NFS services/daemons are running on the Solaris x86 machine. I've tried the following variations but, all have failed to produce successful results:
# mount -F nfs x.x.x.x:/f /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f
# mount -F hsfs x.x.x.x:/F /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F
[FYI: S10_106_SOFTWARE is the DVD's label as reported by Windows Explorer.]
# mount -F hsfs x.x.x.x:/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/s10_106_software
# mount -F nfs x.x.x.x:/S10_106_SOFTWARE /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F nfs x.x.x.x:/s10_106_software /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/s10_106_software
# mount -F hsfs x.x.x.x:/F/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/s10_106_software
# mount -F hsfs x.x.x.x:/f/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/F/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/S10_106_SOFTWARE
I've also tried mounting it at bootup by adding the appropriate entry in the /etc/vfstab file but, this does not work as well. I've tried Google'ing for an answer to my issue but, I haven't been able to find anything that applies directly to what I'm reporting. It's usually chatter about mounting from one UNIX server to another. Any advice from the community would be greatly appreciated.

After three weeks, you deserve a reply. Windoze does
not natively support NFS.Also deserves a decent answer...
There are two ways to do this:
Install Microsoft's free "Windows Services for UNIX," which includes a Windows NFS server; or
Install the 'sharity' package (google for it); it provides Solaris systems the ability to mount Windows shares

Oracle 8.1.5 Client/WLS/Solaris x86

has anyone been able to get Oracle's client 8.1.5 running on Solaris x86 in conjunction with WLS to talk to back-end Oracle? Any help would be greatly appreciated.thanks.

This will not work. We have not built the native libraries to work with
Solaris on Intel..
I suggest trying the platform independent type 4 JDBC driver available for
free from Oracle. It is supported (as is any JDBC driver) with WebLogic
Server. To download it:
Go to http://www.oracle.com and select the "Download" option.
From the resulting page, use the "Select Utility or Driver" dropdown to
select Oracle JDBC drivers
From the resulting page, scroll down a little (since SQLJ stuff appears at
the top).
Or, to go directly there:
http://technet.oracle.com/software/tech/java/sqlj_jdbc/software_index.htm
Thanks,
Michael
Michael Girdley
BEA Systems Inc
"Dean Davis" <[email protected]> wrote in message
news:3a267487$[email protected]..
has anyone been able to get Oracle's client 8.1.5 running on Solaris x86in conjunction with WLS to talk to back-end Oracle? Any help would be
greatly appreciated.thanks.

Solaris x86 with Oracle RAC 10g Enterprise Edition Release 10.2.0.3.0

Hello,
Maybe you can help me (new on RMAN backup) in doing this.
I have configured a single Oracle 10g database to have backup with RMAN with following steps:
1. $ mkdir $ORACLE_BASE/rman_scripts
2. $ mkdir $ORACLE_BASE/logs
3. $ mkdir $ORACLE_BASE/tracking
4. $ mkdir $ORACLE_BASE/c_backup
5. $ sqlplus sys/<password> as sysdba
6. SQL> alter system set db_recovery_file_dest_size = 50G scope=both;
7. SQL> alter system set db_recovery_file_dest='${ ORACLE_BASE}/flash_recovery_ area' scope=both;
8. SQL> alter system set log_archive_dest_10='location= use_db_recovery_file_dest';
9. SQL> shutdown immediate
10. SQL> startup nomount
11. SQL> alter database archivelog;
12. SQL> alter database open;
13. SQL> alter database enable block change tracking using file '${ORACLE_BASE}/tracking/rman_ change_track.f';
14. $ rman target /
15. RMAN> CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK
TO '/var/opt/oracle/flash_ recovery_area/ORCL/c_backup/% F';
16. RMAN> CONFIGURE CONTROLFILE AUTOBACKUP ON;
17. RMAN> CONFIGURE BACKUP OPTIMIZATION ON;
18. RMAN> CONFIGURE RETENTION POLICY TO RECOVERY WINDOW OF 7 DAYS;
19. RMAN> exit
I need to configure incremental backup with RMAN on a two node Solaris x86 with Oracle RAC 10g Enterprise Edition Release 10.2.0.3.0 installation.
We also use ASM to store database files, and have Oracle software installed on separate file systems (two Oracle roots for Node1 and Node2).
I have following questions:
1) where to put Flash Recovery Area (FRA)?
I saw recommendations to put FRA on the ASM, is this the best way to do it?
2) Can I put FRA on another file system (not on the ASM) which is available only from Node1? This way I can save space on the ASM.
3) Is it possible/recommended to run RMAN from Node1 only?
Below is the script used to run RMAN on the normal Oracle database (without RAC) which I need to change :
=============================================================================================
2.0 Oracle backup script: /opt/app/oracle/rman_scripts/backup.sh
Use this for daily backups, possiblly as a cron job.
Once a week run this: /opt/app/oracle/rman_scripts/backup.sh FULL
All other days of the week: /opt/app/oracle/rman_scripts/backup.sh INCREMENTAL
Note: You may have to change ORACLE_SID, ORACLE_BASE below to match your database.
=============================================================================================
#!/usr/bin/ksh
ORACLE_SID=orcl
ORACLE_BASE=/opt/app/oracle
ORACLE_HOME=${ORACLE_BASE}/product/10.2.0/db_1
PATH=${ORACLE_HOME}/bin:/usr/bin
LOGDIR=${ORACLE_BASE}/logs
LOGFILE=${LOGDIR}/rman.log
if [[ $# < 1 ]]
then
echo "usage: backup.sh FULL|INCREMENTAL"
exit;
fi
BACKUPTYPE=${1}
full='FULL'
incremental='INCREMENTAL'
if [[ $BACKUPTYPE == $full ]]
then
$ORACLE_HOME/bin/rman target / nocatalog log ${LOGFILE} append << eof
run {
backup database;
SQL 'alter system archive log current';
backup archivelog all;
delete noprompt obsolete;
exit;
eof
echo ''
fi
if [[ $BACKUPTYPE == $incremental ]]
then
$ORACLE_HOME/bin/rman target / nocatalog log ${LOGFILE} append << eof
run {
backup database;
backup incremental level 1 database;
SQL 'alter system archive log current';
backup archivelog all;
delete noprompt obsolete;
exit;
eof
echo ''
fi

Hi [email protected],
Q1) where to put Flash Recovery Area (FRA)?
A1) With RAC: on the shared storage
I saw recommendations to put FRA on the ASM, is this the best way to do it?
If you want your backups to be available for both nodes you have to use shared storage or tape using an mml library.
So if you want to use the FRA for rman backups and the database is on ASM just make ASM the standard for the FRA as well.
Q2) Can I put FRA on another file system (not on the ASM) which is available only from Node1? This way I can save space on the ASM.
A2) Than you cannot recover in case Node1 is down. Best would be to send your storage admin to a training course so he can manage the clustered raw devices needed for ASM.
Q3) Is it possible/recommended to run RMAN from Node1 only?
A3) No see A2.
Regards,
Tycho

Dell Hardware on Linux or Solaris x86

Hi,
My company is considering moving to dell hardware in a move to drive TCO down. We currently run Sun sparc (240, 490,890) servers and they are nearing end of life. Doing the research, even visited some vendors and from what we've seen, running either RH 5 or even Solaris (x86) on Dell could prove to be a good move. We're running mostly 10.2 databases with a couple of 9.2 that we hope to have upgraded by year end.
Has anyone made a similar move and what is your experience? I worked on Dell about 4 years ago and back then we felt there were reliability issues. They crashed a little too often for my liking. I realize some of it was do to OS panics and not just hardware but that is part of the package.
Any feedbackup would be greatly appreciated.

If you're going to go Dell, you might aswell go the whole way and run RedHat.
Aside from the support issues mentioned (I'm not familiar with that aspect) Solaris has a history of being much more expensive to run (largely due to the cost of the employees that know it) with the major advantage being: better integration with Sun hardware.
As for Dell reliability, there's a reason we're an HP shop..

Ndd in Solaris x86

Hi I need to know How can I see parametes list of networks interfaces in Solaris x86, I can't use the utility ndd for the network interface, I am working in a V65x and the NIC is e1000g.
Thanks

kstat e1000g:0 might work, but I'm not 100% if kstat
statistics are supported by the e1000g driver. And if they are available,
I'm not sure if they are accurate.
kstat should list the interface speed, and the duplex setting.

Why is my mac shuts down suddenly

My mac shuts down suddenly, i have to press any botton in oder to turn on, and if I stop messing with the mac it will shutdown. Any advice??

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Weblogic 8.1 for solaris x86 download

hi, i'm looking for weblogic 8.1 for solaris x86, where i can download the files?
thanks

hey thanks for the reply, sorry for my late response, well last time i was found the archive of all BEA Release Product with metalink account, i was downloaded the weblogic 8.1 SP4 for solaris x86.. the installation seems fine, until i try to create the domain.. here is my step installation
-bash-3.00$ ./config.sh
Java Accessibility Bridge for GNOME loaded.
Unable to instantiate GUI, defaulting to console mode.
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Create or Extend a Configuration:
Choose between creating and extending a configuration. Based on your selection, the Configuration Wizard guides you through the steps to generate a new or
extend an existing configuration.
->1|Create a new WebLogic configuration
| Start here to create a WebLogic configuration in your projects
|directory.
2|Extend an existing WebLogic configuration
| Start here to extend an existing WebLogic configuration. Use this
|option to add applications and services, including Database access (JDBC)
|and Messaging (JMS). This option also enables you to extend functionality
|by enabling WebLogic Workshop.
Enter index number to select OR [Exit][Next]> 1
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Select a Domain Template:
Please select a template from the list or select another directory of templates.
* [wildsoft/oracle/weblogic81/common/templates/domains]
1|Basic WebLogic Workshop Domain 8.1.4.0
| BEA Systems, Inc.
| Create a basic WebLogic Workshop domain, without installing sample
|applications. Domains created from this template will support the
|WebLogic Server and WebLogic Workshop runtime functionality, including
|support for J2EE applications, Web applications, Web Services and custom
|controls. Use domains created from this template for development of
|WebLogic Workshop applications.
->2|Basic WebLogic Server Domain 8.1.4.0
| BEA Systems, Inc.
| Create a basic WebLogic Server domain without installing sample
|applications.
3|WebLogic Server Examples Domain 8.1.4.0
| BEA Systems, Inc.
| Create the WebLogic Server Examples domain in a directory outside of the |installed kit. The Examples domain contains a collection of examples to
|show best practices for coding individual J2EE APIs.
4|Avitek Medical Records Sample Domain 8.1.4.0
| BEA Systems, Inc.
*Enter index number to select OR [Down][Exit][Previous][Next]> 2*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Choose Configuration Option:
*Do you want to run the wizard in express mode?
->1|Yes
2|No
*Enter option number to select OR [Exit][Previous][Next]> 1*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Configure Administrative Username and Password:
Create a user automatically assigned to the Administrative Role. This user is
the default administrator used to start development mode servers.
| Name | Value |
_|_________________________|_________________________________|
1| *User name:       |            weblogic             |
2| *User password:     |                                 |
3| *Confirm user password: |                                 |
4| Description: | The default administration user |
Select Option:
1 - Modify "User name"
2 - Modify "User password"
3 - Modify "Confirm user password"
4 - Modify "Description"
*Enter option number to select OR [Exit][Previous][Next]> 2*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Configure Administrative Username and Password:
Create a user automatically assigned to the Administrative Role. This user is
the default administrator used to start development mode servers.
"*User password:" = []
Input new User password: OR [Exit][Reset][Accept]> weblogic1*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Configure Administrative Username and Password:
Create a user automatically assigned to the Administrative Role. This user is
the default administrator used to start development mode servers.
| Name | Value |
_|_________________________|_________________________________|
1| *User name:       |            weblogic             |
2| User password:     |            ******** |
3| *Confirm user password: |                                 |
4| Description: | The default administration user |
Select Option:
1 - Modify "User name"
2 - Modify "User password"
3 - Modify "Confirm user password"
4 - Modify "Description"
5 - Discard Changes
*Enter option number to select OR [Exit][Previous][Next]> 3*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Configure Administrative Username and Password:
Create a user automatically assigned to the Administrative Role. This user is
the default administrator used to start development mode servers.
"*Confirm user password:" = []
Input new Confirm user password: OR [Exit][Reset][Accept]> weblogic1*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Configure Administrative Username and Password:
Create a user automatically assigned to the Administrative Role. This user is
the default administrator used to start development mode servers.
| Name | Value |
_|_________________________|_________________________________|
1| *User name:       |            weblogic             |
2| User password:     |            ******** |
3| Confirm user password: |            ******** |
4| Description: | The default administration user |
Select Option:
1 - Modify "User name"
2 - Modify "User password"
3 - Modify "Confirm user password"
4 - Modify "Description"
5 - Discard Changes
*Enter option number to select OR [Exit][Previous][Next]>next*
<--------------------- BEA WebLogic Configuration Wizard --------------------->
Domain Mode Configuration:
Enable Development or Production Mode for this domain.
->1|Development Mode
2|Production Mode
*Enter index number to select OR [Exit][Previous][Next]> 1*
A fatal error has occured. This application will terminate.

ASE for Solaris x86

I really need a developers edition of ASE for Solaris x86. The current versions that are available are only for Linux or Windows. Is there anywhere I can get the Solaris x86 version??

You haven't mentioned which ASE version you're looking for so I'm going to assume a newer/recent version of ASE 15.7 is sufficient ...
For quite awhile now all ASE downloads (IR, GA, EBF, SPxxx) have contained the entire code line (ie, you don't have to find a GA release and then apply a smaller/delta ebf patch file to get the latest version).
If you've got access to the EBF downloads @ sybase.com you should be able to download a recent copy of ASE 15.7 for Solaris/x86. During installation just pick the developer license version (the install will generate a generic *lic file for the developers version).
While there may be a way to download the file from the SAP website(s), I wouldn't have a clue since a) the SAP websites are poorly-designed/confusing and b) SAP is clamping down pretty hard on what Sybase related downloads are available and to whom.

IMac shut down suddenly and won't boot back up

This morning my iMac shut down suddenly. All I had open was Google Chrome and I was just on Facebook and that's it. When I tried to boot it back up, it wouldn't load past the startup sound, wherein it would appear to shut back down,or at the very least the screen would go black (my mouse has lights that stay on when the computer is on, and the light kept going on and off while the screen remained black). This was the case for at least a half hour until it suddenly booted itself back up all on its own. I had it on throughout the day, just browsing the internet and watching Youtube. It shut itself down twice during the day, and both times it restarted on its own right away after showing me a grey screen with the Apple logo and a progress bar. Now it just shut itself down again and it won't make it past the progress bar screen - if it even makes it that far, sometimes it shuts off right after it makes the startup sound. It keeps trying to boot up on its own over and over again, but it keeps shutting down right away. All the fixes I've searched for so far require a computer that actually boots up all the way so I don't think I could run any reports if I tried!
I'm running the latest version of Yosemite (10.10.2?).
Model number A1311
Not entirely sure what specs are useful to know so I'm just gonna write some of what's on the box it came in:
3.2 GHz Intel i3 processor, 4MBshared level 3 cache
4GB of 1333MHz DDR SDRAM
1TB serial ATA hard drive
ATI Radeon HD 5670 graphics processor with 512 MB of GDDR3 memory
Bought it around fall of 2010. Not sure if it's worth trying to get it fixed (I live nowhere near an Apple store) or if I should just get a new computer, but I would like to know what's wrong, if possible.

Try to boot into the Recover Partition by holding down the Command + R keys on startup. If it still won't boot then the HD has probably crashed. The is likely a AASP in your area, you can locate one by clicking AASP Locator, take it to one to be professional diagnosed. If it's only the HD, assuming you have been backing up, restoring to a new HD is pretty simple.

Hi, My network went down earlier in the week. Now it is fine, but my macbook airport no longer detects it and keeps asking for a WAP. When I put the password in, it 'times out'. I'm getting rather fed up.

Hi, My network went down earlier in the week. Now the network is fine, I can connect through the ethernet cable, but my macbook airport no longer detects it, when prompted, macbook will find it, but I get asked for the WAP. When I put the password in, it 'times out'. Prior to the network problem my macbook worked fine everytime. Anyone know the answer?

My guess is all the issues are probably related and fall back to malware.
AVG is probably correct in identifying malware. So I suggest you try some cleaning tools other than Emsisoft .
ones I use (all of them one after the other until I find one that can cope) are;
Roguekiller http://www.adlice.com/softwares/roguekiller/
Malwarebytes anti malware Free http://www.malwarebytes.org/mwb-download/var2/confirm/
ESET online scanner http://www.eset.com/int/home/products/online-scanner/
So first create a clean boot in Windows using Microsoft's instructions https://support.microsoft.com/kb/929135?wa=wsignin1.0 and then run the anti malware applications.
My outside looking in guess is that malware has set itself up as an internet proxy and is is downloading copies of itself and other malware, blocking some mail port as times as downloading more malware is more important, and probably breaking your tivo as well..
Try the malware programs first. If that does not work I will try and talk you through some logging to see what is happening.

Install oracle 8.1.7 on Solaris(x86) 10 b72

Has anyone Installed oracle 8.1.7 on Solaris(x86) 10 b72???
When I run runInstaller I have
135$ Initializing Java Virtual Machine from ../stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/jre. Please wait...
ld.so.1: /ora_inst/stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/i386/native_threads/jre: fatal: relocation error: file /ora_inst/install/../stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/../lib/i386/native_threads/libawt.so: symbol XShmQueryExtension: referenced symbol not found (/ora_inst/install/../stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/../lib/i386/native_threads/libawt.so)
ld.so.1: /ora_inst/stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/i386/native_threads/jre: fatal: relocation error: file /ora_inst/install/../stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/../lib/i386/native_threads/libawt.so: symbol XShmQueryExtension: referenced symbol not found (/ora_inst/install/../stage/Components/oracle.swd.jre/1.1.8.10/1/DataFiles/Expanded/jre/solaris/bin/../lib/i386/native_threads/libawt.so)
java.lang.UnsatisfiedLinkError:

try this:
LD_PRELOAD="libX11.so libXext.so" ; export LD_PRELOAD
./runInstaller

Network is down suddenly on my Solaris X86 box

Similar Messages

Maybe you are looking for