Network issues after trying everything

After replacing the glass screen (wanted blue instead of black), mobile network is not functioning properly. I cannot make or receive calls at all, and basically unless I'm outside, I can't get or send text messages or use the internet. Tried soft and hard resets, taken it into the store- employee who helped me couldn't find anything wrong with it (after that i did the hard reset)- nothing has worked.

Since you have some functionality (texting while outside) have you tried to use another sim card?
Since you took the screen apart there could be an antenna issue now.

Similar Messages

TS1398 help!!! i am unable to connect to a wifi network and ive tried everything but nothing seems to work!!! can someone help pls

help!!! i am unable to connect to a wifi network and ive tried everything but nothing seems to work!!! can someone help pls

try connecting to another wifi network to isolate the issue. at this point it's impossible to tell if it's your phone or your network

Networking Issues after Upgrading to Windows 8.1

I have a Windows 8 desktop PC that is working fine with my network. I can browse the Internet fine using all major browsers etc. After upgrading to Windows 8.1 through the Windows Store I noticed that my wired networking was not working correctly.
The status of the network does not change (i.e. it doesn't change to Limited Connectivity) however browsing to sites in Chrome, IE or Firefox doesn't work as well as Windows 8.
IE11 gives me the error "This page can't be displayed, make sure the web address is correct" and other browsers give a similar error. I normally have to refresh 2-3 times to get a new page to load, sometimes even more. Everything works
fine from a laptop connected at the same time so it isn't an network issue with my provider.
I thought this might be a driver issue with the two on-board Marvell wired network adapters. I wasn't able to rollback the driver to older versions I found on the Internet. I then purchased another network card, Intel Desktop gigabit and the
issue still persists with that adapter. I then tried a USB wireless adapter and the issue still persists using wifi with the wired adapters disabled. I tried a new network cable and no luck either. I also tried resetting the IP stack using
the various netsh commands.
After that I thought I might try reset the Windows 8.1 PC, however that didn't work as I didn't have the restore image available as I upgraded from the Windows Store. I then tried installing Windows 8.1 fresh using a ISO with my Windows 8 key using
some of the recent guides that are available. That all worked but it didn't fix the networking issues.
I re-installed Windows 8.0 and the networking is now fixed and back to working normal again. I'd like to try again but I think I will have the same problems. I can't imagine why this would be a driver issue as I tried 3 different network adapters
and two installs of Windows 8.1. Any ideas what would be the cause of the Windows 8.1 issue?

HI,
Since this issue only occurred in the your desktop PC, and many network adapters you tried, failed, thus I think maybe we should focus on the model of your desktop PC, I suggest you update the BIOS and chipset from the manufacture to improve
the performance of win8.1.
Please also test this issue in safe mode with networking.
Please refer to:
Windows Startup Settings (including safe mode)
http://windows.microsoft.com/en-in/windows-8/windows-startup-settings-including-safe-mode
I’d like to share the following article with you:
Wired and wireless network problems
http://windows.microsoft.com/en-IN/windows/network-connection-problem-help#network-problems=windows-81&v1h=win81tab1&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1
Regards,
Yolanda
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.
The issue occurs in safe mode as well under Windows 8.1. The motherboard is an Asus P5B Premium, however it works on Windows 8. How would I update the chipset when booted into Windows 8.1? In Device Manager it wasn't allowing me to update
the network drivers as they were newer versions already installed.
Edit: I also installed at Intel Chipset Device software dated 8/8/2013 with version 9.4.0.1026 and the issue still occurs. I am also running the latest BIOS that is available.

How can i fix my iphone 3gs when i have network issues after updating to IOS 6.1.3 and avoid the connect to ITunes screen?

Im an owner of an Iphone 3gs.
When I updated my software to IOS 6.1.3 I started having network issues such as my phone would go on searching, it would search for signal and then No service after few minutes it would restart and when its on again it would show me Connect To Itunes screen, I tried connecting but nothing happens and if I just leave it as it is it will just keep on restarting and showing the same screen sometimes I might get lucky and the phone will start working again but No Service and if I turn on my 3G for the times Im outdoors it will just restart again so 3G is also another problem I have got. Today I decided to take it to an Apple Store, the guy restored it and now what happens is that it switches on and is showing me the connect to Itunes message but with black backround and i cant do anything it keeps on restarting and showing the same thing. Please if there is anyone that would like to spend some time with me to help me out, he would be more than Welcome.
Im located in South Africa

iOS: Device not recognized in iTunes for Mac OS X

Ipod isn't recognized by itunes after trying everything

i've searched the apple website high and low to find a solution to my problem with itunes 7. i have a 60GB 5th gen and no matter how many times i have re-installed, updated and did the 5 r's my ipod will not show up in itunes after i close out and open again. i know many poeple seem to be having this problem but anybody know a SURE way to fix this or know when apple is going to release an itunes and ipod update that is worth spending my time on???
p.s. ipod update in itunes 7 just sits there scrolling but is actually not responding, let it sit and do its thing for 7 hours. any help please!!!!

i ahve upgraded to the newest possible itunes hours after it came out. my ipod also has software version 1.1.2. the link you posted i have already tried. it works if i need to get my ipod to show up but the next time i start up itunes the same problem happens. ive tried everything in that article and some things of my own. ive even erased all my library saved data and uninstalled along with getting rid of all .dll files to start back at absolute scratch. also now i cant import more than 4 songs from a file at a time otherwise it wont register and wont load the songs to my library. (this made it take very long to redo my library) any other suggestions jason? <frustrated>

ITunes does not recognize iPod (3rd gen?) even after trying everything...

I have searched and not found this exact problem on any of the forum pages. My computer (PC) recognizes my iPod as an external USB drive. It is completely charged up (from the AC power). No error messages. Screen shows the "updating - do not disconnect symbol" constantly while docked but the pod does not show up in iTunes at all. I can get the main screen (menu) page by disconnecting the USB device through Windows, but when I try to select any of my data on the pod it shows nothing downloaded on the device. I've tried everything in the support section (most recent version of iTunes, checked that iPod service is running, reinstalled the COM interface for iPod service, deleted and reinstalled iTunes, etc. As a final resort, I "restored" the pod to factory settings using iPod Updater, but no joy...To say I'm unhappy is putting it mildly. Any suggestions before I jump out a window or something????
Pentium III Windows XP

Sorry for the curt/short explanations, but I am very frustrated.
My computer recognizes my iPod. iTunes does not.
iTunes does not recognize my other nano (2gb) or my friends shuffle. However, when my friend's shuffle is plugged into the computer, the iTunes window will pop up though I still can't see the actual device. On my nano and video, iTunes does not pop up.
In response I have...
I have reset my iPod.
*no luck
I have uninstalled an reinstalled the program 5-8x.
*no luck
I have run Spybot and Ad-aware just in case.
*no luck
I have changed the power management on my USB hubs.
*no luck
I have specified and changed the letter pathway of not only my iPod but my other usb peripherals.
*no luck
I have "reinstalled" the COM Interface about 5x after various changes.
*no luck
I have downloaded the recent iPod updater and that dealt with my iPod JUST FINE and then ran iTunes.
*no luck
I have selectively chose the with processes are on the startup.
*no luck
but for good measure, here are the processes running right now:
taskmgr.exe
svchost.exe
firefox.exe
Zboard.exe
qttask.exe
alg.exe
ctfmon.exe
lsass.exe
services.exe
winlogon.exe
csrss.exe
smss.exe
explorer.exe
iPodservice.exe
zboardtray.exe
spoolsv.exe
iTunesHelper.exe
wdfmgr.exe
Programs like Anapod recognize my iPod. They both mount and execute processes just fine.
Can anyone help me here??
hp pavillion zd7360us Windows XP Pro iPod Video 60 GB and iPod Nano 2GB

WLan connected, iPad and iPhone internet ok, iMac not working after trying everything (manual ip etc...)

I am quite new with a mac computer. But i think i nearly tried everything, i have no idea what else could help...
My iPhone and iPad are working perfektly in the wlan. My iMac works very rarely. Yes it worked once by manual ip, but later it did not work again.
Wlan always works (sometmes it takes a few seconds until thesymbol is fat, mostly it starts with "no internet")
I tried so many things...
- manual ip found out by my windows pc
- $ in front of the password
- the apple faqs on the websites
Very strange, but i hope someone solved an comparable problem already ;)
Thx!

I had a surfstick before, does that influence the whole thing?
And another thing: in other wlans the iMac worked perfectly... Without any manual settings etc.
Anyone an idea?

Error: out of memory (after trying everything i found on the forum)

hi guys,
I'm editing a short film shot in HDVCPro 1080i50i
I'm on FCP5 on a MacBook 2Ghz Intel Core2Duo with 1,7Go Ram & Mac 10.4.9. Stockage is 120go with 40go free.
The rushes & project is on an extern LaCie disk (it takes 200go of the total 250go).
When I add rushes on the timeline, the error message "out of memory" keep coming up.
I tried everything i found on the forum (trashing preferences, lowering the application rate in memory & cache, making several "mini projects"...).
Im runnin out of ideas & my only option is to use a Power PC G4 with 1.2go RAM (I doubt it will change anything)
If any of you can suggest something, or at least confirm me that i've to invest in a MacPro ...
Thx
g4 & macbook Mac OS X (10.4.9)
g4 Mac OS X (10.4)

easy setup is "DVCPro HD 1080i50" & sequence settings are the same...
i don't understand why it worked fine during my first days on the project & began to mess only now...
thanx

IPhone cellular network issues after iOS 7.0.6 update

iPhone 5s recently updated to 7.0.6 having cellular network issues. Works on LTE, dead while on 3G. Wifi works. Anyone know why?

Indeed, but if you are in a weak coverage area or even somewhere like a basement, LTE occasionally cuts out leaving you with a 3G connection, which the device will display accordingly. During the times when my device is on 3G I do not receive voicemail, iMessages, or any network connection and get a message telling me my device is "not connected to the internet" even though the 3G indicator is present. Once LTE kicks back in or I find a wifi connection this is no longer a problem, but the phone automatically toggles back and fourth between LTE and 3G more often than desirable which became noticeable when stuff stopped working during the 3G periods.

[solved] Wireless network issues after installing gnome3

After installing gnome 3 I can't connect to my wireless network any more. I start gnome using 'xinit gnome-session' after loggin in at a command line. Here are some relavent ouptuts:
$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:25:4B:8D:B7:07
inet6 addr: fe80::225:4bff:fe8d:b707/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10
eth1 Link encap:Ethernet HWaddr 00:25:4B:BE:74:BC
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:20 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:32 errors:0 dropped:0 overruns:0 frame:0
TX packets:32 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1920 (1.8 Kb) TX bytes:1920 (1.8 Kb)
$ iwconfig
lo no wireless extensions.
eth0 IEEE 802.11 Nickname:""
Access Point: Not-Associated
Link Quality:5 Signal level:0 Noise level:234
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
eth1 no wireless extensions.
Trying to connect to a network through gnome-control-center:
$ sudo gnome-control-center
** (gnome-control-center:6172): WARNING **: Error in getting active connection 'Vpn' property: (19) Method "Get" with signature "ss" on interface "org.freedesktop.DBus.Properties" doesn't exist
** (gnome-control-center:6172): WARNING **: _nm_object_array_demarshal: couldn't create object for /org/freedesktop/NetworkManager/ActiveConnection/4
** (gnome-control-center:6172): WARNING **: Error in getting active connection 'Vpn' property: (19) Method "Get" with signature "ss" on interface "org.freedesktop.DBus.Properties" doesn't exist
** (gnome-control-center:6172): WARNING **: _nm_object_array_demarshal: couldn't create object for /org/freedesktop/NetworkManager/ActiveConnect
xterm output when trying to connect through the network applet:
Window manager warning: Log level 16: Device activation failed: (32) Insufficient privileges
Last edited by dave1022 (2011-05-14 17:14:12)

iskandr wrote:
Hello,
I'm having problems with my wireless network connections, too. I did a fresh arch install with gnome3 some days ago to avoid any issues when upgrading, but i just can't access any wireless networks now. Everything else works like a charm, though. I followed the usual steps to set up my network/wifi with all the required modules and packages (broadcom-wl from the AUR, etc.) but it doesn't work like it did with gnome2 and xfce4.
My iwconfig/ifconfig output looks like dave1022's. Don't know if this is of any help...
The nm-applet in the gnome3 "panel" actually lists nearby wireless networks, but once I click on one of them, gnome asks me for authentification with my root password (user password does not work). I don't think it should be this way. If I enter my root password here, nothing happens whenever I click on the concerned network to connect to it. I deleted the /etc/NetworkManager/system-connections/<SSID> file to reset the authentification process.
I tried to consult the gnome3 pages in the wiki, but couldn't find any valueable hints either...does anyone have any idea what I might have done wrong or forgotten?
It's exactly the same for me and it's driving me nuts. I'm using iwl3945
[EDIT]
Well... actually installing the applet solved it for me. Is the applet actually needed for Gnome 3 or is a workaround?
Last edited by Slurp (2011-05-14 17:11:19)

Networking issues after a move and upgrade

I just moved, and did a massive system upgrade, moving over fully to systemd.
Everything works fine, except my network seems to crap out after a random period of time (sometimes 2 hours, sometimes 10 minutes, sometimes it stays up for days).
ive used different ports on my router, different ethernet cables, so im pretty sure the issue is with my laptop
i used the ethernet-static script and put in my own network info (using 10.0.0.0/24 network), a correct default gateway, and working nameservers.
on my main computer i have MPD going over a SMB share, and sometimes it just stops working. When i open up Wireshark i see im getting ICMP Dest unreachable errors.
What could be causing this? Any ideas?
Last edited by ptchinster (2013-03-10 19:16:56)

No. Something is wrong with modprobe I guess. I noticed yesterday that the line that usually looked lieke this
eth1 Link encap:Ethernet HWaddr 00:10:A7:27:5D:A2
was like this
eth1-00 Link encap:UNSPEC HWaddr 00-10-A7-27-5D-A2-00-00-00-00 or something like that
So I did a manual modprobe 8139too and I got
eth2 Link encap:Ethernet HWaddr 00:10:A7:27:5D:A2
I changed the settings in rc.conf from eth1 to eth2, restarted the networking script and the network was OK. But this doesn's anwer the question what was wrong with it in the first place...

Windows 7 - Files missing from network share after trying to burn and no data cached to be burned

I ran into an issue trying to burn some file from a network share using Windows 7 Home Professional. I was trying to burn some .jpg files from a mapped network share drive using explorer. Every time I would drag the files to be burned from
the share drive to the explorer screen to be burned, the files would disappear from the share. To make things worse the files would not show up in the screen to be burned. I was unable to locate any of the files on either of the systems when performing
a search after this took place. I verified that the steps that I was taking to burn the files were the same as outlined on the Microsoft site. No matter what I did to burn these files, they were deleted from the mapped network drive.
Below are the steps that I took that both resulted in the files being deleted as well as what I had to do to finally burn the disc.
Steps that resulted in files being deleted:
1. Insert blank CD into drive.
2. From prompt select burn using explorer (Mastered Format)
3. Enter title and select with CD/DVD, click Next.
4. Open a second explorer window, navigate to mapped network drive with files to be burned and snap next to explorer to be burned.
5. Drag and drop the files from the share drive to CD.
This where the train would fall off the tracks every time. I would receive a message that the file(s) no longer exist and if I wanted to continue. From here the files would be deleted from the share drive. The best part is that the files
would also NOT be locally stored to be burned.
Steps to burn share files WITHOUT delete:
Follow steps outlined above, but instead of just dragging and dropping the files as outlined in step 5 select the files from the network share location, right mouse select copy. Then right mouse select paste in the explorer window to be burned.
I have tested this many times and every time ended up with the same problem. At this point I am sure that there is a problem with the way that Windows 7 is performing the burn. The system that I was using to burn is Windows 7 Home Professional
with all the patches and updates loaded. The remote system is Windows XP Professional with all the patches and updates loaded.
Thanks in advance

Yes, the problem is still continuing. However, after looking into as much of it as I can, I can confirm something that r.p.b_ started stumbling on. The files are deleted IF AND ONLY IF a user is using the built-in Windows 7 disc burning utility AND is dragging
and dropping the files to the drive from a network share; this doesn't happen locally. If you watch what happens in the native folder, the files are literally scrubbed from the drive as they are processed and added to the image. However, if you Right Click
on the files and copy them, then Right Click->Paste onto the drive, they remain. (The keyboard shortcuts also worked.) Also, 3rd party disc burning utilities function they way the should. (In other words, they don't delete the files.)
My speculation is that there's a bug in the coding that sees the network share as a temporary buffer file while the image is being prepared. Then, as the files are processed in what ever way is needed, the "temporary buffer" is being deleted. The result:
lost files on a network share. But, this is just speculation.

Network issues after returning from sleep mode

I'm noticing this issue on T440, Twists, T420s, whether it's Windows 8, Windows 8.1 or Windows 7. Sometime around the end of last year and the beginning of this year, my users suddenly started reporting problems with the machines after returning from sleep mode. The network adapter (whether plugged in or using wifi), would show limited connectivity and would not connect to the internet until the machine is rebooted.
I've tried updating drivers, using system restores, disabling the network adapters from shutting down to conserve power, OS network diagnosis & network adapter resets, none of which has worked. Hibernation is disabled on all machines.
The only fix I have is to reinstall the OS over the top of the system and reinstall all updates. Looking for help with this issue.
Thanks!
Solved!
Go to Solution.

Hi Mertz74,
Thank you for replying us back!
Please check with uninstalling power manger and reinstall it with latest driver.
Download chipset driver from Lenovo drivers page and install it.
Please check with above option to resolve the issue.
Below is the link to enter the downloads page and download updates accordingly, please click on "Select Product" then in "QUICK PATH" enter the MTM no. select the exact model.
http://support.lenovo.com/en_US/downloads/default.page#
Hope this helps. Do post back if issue persists!
Best regards.
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

HP Officejet Pro 8610 saying "printer not connected" after trying everything I can think of...

The printer worked before. It's working when we print from other devices. I tried updating my OS, no luck. I tried canceling the jobs and restarting, no luck. Tried restarting the computer, no luck. Tried deleting the printer from my computer and now adding it back and that's not working either. The printer deleted and now the computer can't find it again. Can someone please help? This is deeply frustrating.

Hello @ElizabethPaul , and welcome to the HP Forums, I hope you enjoy your experience!
I see you are experiencing connectivity issues. I would like to help!
I would recommend performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I'd also suggest this document on Wireless printing center Troubleshooting Issues.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Network Issues After Update

Today I decided to do a full pacman -Syu and I received a bunch of updates which it asked me to install. I went ahead as normal and everything seemed to install fine. However, upon rebooting the machine I found that the internet connection was acting strangely. All pings performed to urls seem to fail (although the addresses seem to resolve correctly) but I can ping perfectly within the network to the router as well as the loopback. All other computer on the network are functioning fine so I know this is not a router issue. One other odd note, whenever I issue another pacman -Syu, pacman is able to reach out and compare the local databases for the packages with the ones hosted on the arch file servers. On a final note my ethernet controller is the Realtek RTL8111/8168B PCI express card, my kernel is ver. 2.6.33 and I am also able to ssh into it from other computer within the network. Any ideas as to what could be going on or what I should try to do to fix this?
Thanks in advance
EDIT: it turned to to be an issue with moblock.
Last edited by threePhase (2010-06-11 08:51:09)

Same here, aeroplane on and off and it works. MMs settings was all wrong but a quick search of the net and everything is ok now.

Network issues after trying everything

Similar Messages

Maybe you are looking for