NETWORK marked [FAIL] but works...
Hi everyone,
Recently, during boot, network is marked as failed but everyhting works properly... This only happens with wireless connection (ipw2100), ethernet is marked [DONE] and works too
Thanks in advance for any advice...
Cheers
I'm not sure if I completely understand your post, but if you have multiple network interfaces and one fails, then network shows fail even if others were successful. There's a bug report filed about it, but it's been quite a while without being fixed...
And if that doesn't answer your question then ignore me.
Similar Messages
-
Autostart of network-service fails, but manual start works fine
I followed a guide to set up a network connection. The steps were to create a network config (/etc/config.d/network)
interface=eth0
address=192.168.1.2
netmask=24
broadcast=192.168.1.255
gateway=192.168.1.1
then a service description (/etc/systemd/system/network.service)
[Unit]
Description=Network startup
Wants=network.target
Before=network.target
[Service]
Type=oneshot
RemainAfterExit=yes
EnvironmentFile=/etc/conf.d/network
ExecStart=/sbin/ip link set dev ${interface} up
ExecStart=/sbin/ip addr add ${address}/${netmask} broadcast ${broadcast} dev ${interface}
ExecStart=/sbin/ip route add default via ${gateway}
ExecStop=/sbin/ip addr flush dev ${interface}
ExecStop=/sbin/ip link set dev ${interface} down
[Install]
WantedBy=multi-user.target
and then enable the service using systemctl enable network.
After the rebooting calling systemctl states the service as failed. If I start it manually using systemctl start network everything works fine.
How do I get it to work with autostart? Thanks in advance.
Last edited by devrandom (2013-08-03 12:22:55)With 'a guide' I presume you referred to this guide
The guide states
To set static IP on enp3s0 interface you will need to create /etc/conf.d/network@enp3s0 config file and run:
# systemctl enable [email protected]
where enp3s0 has to be changed into your own interface name.
Note that the EnvironmentFile has to change to /etc/conf.d/network@<interface>. -
Hi folks,
I hv a big trouble in FTP upload.
I own a VPS server, and now is rush time I need to upload some file.
Now, I use CUTEFTP, TRANSMIT, CODA, CYBERDUCK in my updated LION, ALL FAILED.
and also, I can not use those client to creat a new file, and not allow to do anything.
maybe you will say, " check your VPS setting ".
the points are:
1. I can use those client in sometimes, and error in sometimes.
2. I can do anything, including upload, download, editing, creating file in my other WINDOWS 7.
Okay, Anyone know the solution? Please help me.. thank you so much.
p.s, ftp is easy job. I dont why APPLE **** this up like always.Problem solved!
I found out how to get FTP to work on my Macs. It was just a hunch, but I tried it and BANGERS ON! (FYI: Bangers is an English slang term for sausages, the kind that is usually enjoyed with a sparkling fermented beverage. Ergo, bangers on implies that the work is done. Time to celebrate.)
As you know, the Macintosh is a very sturdy operating system based almost entirely on Unix, but with a candy apple shell GUI. The developers of this candy coating went to great lengths to provide transparent services to the users that once were only available to the zealous key coders of yesteryear. File Sharing is one such feature. All one has to do is turn it on and specify a folder, and that folder makes itself discoverable on the local network. Oddly though, having it on interferes with passive FTP. All I did to make passive FTP work was to inadvertently decide that maybe … just maybe … it was a problem because it was another kind of File Transfer Protocol. So, I tried turning it off and the rest is history.
BANGERS ON! -
WLST deploy fails but works fine via admin console
RHEL 5.6
Jrockit 1.6.0_20-R28.1.0-4.0.1
Weblogic 10.3
Alfresco 3.3.4 (295)
Oracle 10.2.0.4
I'm experiencing problems when attempting to deploy a WAR using WLST using the below python script. If I deploy this WAR using the Weblogic Admin Console, all works well. When I attempt the same deployment using WLST, the deployment 'appears' to work and the script shows no sign of error BUT the application does NOT show up at all in the admin console. I'm using the same authentication information in both scenarios.
connect(username,password,'t3://' + adminServer + ':8001')
try:
edit()
startEdit(waitTimeInMillis=30000)
except:
traceback.print_exc(file=sys.stdout)
print "Failed to aquire edit lock"
# cannot undo when we do not has the lock
#undo(defaultAnswer='y')
#stopEdit()
sys.exit(1)
try:
for app in cmo.getAppDeployments():
if app.getName() == appname:
print ('Application \'' + appname + '\' is already deployed, removing previous deployment...')
undeploy(appname)
break
except:
traceback.print_exc(file=sys.stdout)
print "Undeploy failed"
undo(defaultAnswer='y')
stopEdit(defaultAnswer='y')
sys.exit(1)
try:
deploy(appname, source, target, upload='true', block='true')
except:
traceback.print_exc(file=sys.stdout)
print "Deploy failed"
undo(defaultAnswer='y')
stopEdit(defaultAnswer='y')
sys.exit(1)
try:
save()
activate()
except:
traceback.print_exc(file=sys.stdout)
print "Activate failed"
undo(defaultAnswer='y')
stopEdit(defaultAnswer='y')
sys.exit(1)
disconnect()
Is it possible to deploy the application unzipped?
- CDMHi Sebastian,
You need to be connected to master database when executing GRANT VIEW SERVER. Try the following it will work:
USE [master]
GO
GRANT VIEW SERVER STATE TO [Domain\User]
Regards,
Basit A. Farooq (MSC Computing, MCITP SQL Server 2005 & 2008, MCDBA SQL Server 2000)
http://basitaalishan.com
Please remember to click "Mark as Answer" on the post that helps you, and to click
"Unmark as Answer" if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. -
Logic pro x, A whole bunch of my audio units failed but worked fine a minute ago
Audio units failed message as half my audio units now will not load.
I have 32 lives and rescanned everything. Did not work.
I own the software and it was all working just fine until I loaded up a different song. Logic glitched out.
The Audio units are still checked in prefs in logic like normal.
Audio units still show up in the project but will no open. They have a question mark. I've seen this before and was able to figure it out with one or two but not half my AU's. Something is different.
I have just loaded the update a week ago and logic was working fine.
I tried deleting my cache with anything Logic x, that did not work.
I restarted the computer several times, no luck.
HALP!!! Thank you for your time
Couldn't be at a worse time as I have a deadline tomorrow for an album I am so close to finishing.. WHY???If you mean all plugins have this issue then...
In Logic's Prefs Audio/Devices, make sure CoreAudio is checked...
Failing that, or if only some plugins have this issue...
Are the plugins that don't work, all ones wrapped in 32lives?
Do any of Logic's own plugins rather than 3rd party ones, have this problem? -
URL Branch with java script target fails, but works as button press
I have a java script that displays a "report is loading" message when the page's submit button is pressed via the optional URL redirect attribute of the button.
Unfortunately, I had to remove the optional URL Redirect so that I could perform some computations and processes as a result of the button press.
I tried to put the script link in a branch attached to the button, but it failed with the following error.
ERR-1777: Page 11 provided no page to branch to. Please report this error to your application administrator.
Restart Application
After the branch to the java script, there is an unconditional branch to page 11.
Any one encounter this issue before and, if so, is there a work around?Hi
Can you not use a URL redirect on the button to call your Javascript function - the Javascript will display the message you want to display, then call
doSubmit('request_name');
...to submit your page, picking up all your processes/computations etc
You then need to define a branch on your page which is conditional on the value of REQUEST - in this case request would be 'request_name'.
regards
Andrew
UK -
Https 1.4.1 post fails but works in 1.3
I have a simple app that runs fine on 1.3.1_04 but it does not run on
1.4.* When I debug I notice 1.3 passes SSL as the protocol and 1.4 passes TLSv1.
Does anyone know how to resolve this problem? Can I use HttpURLConnection? Do I need to use sockets?
The error occurs when I try and post the username and password.
WARNING and ERROR
SEND TLSv1 ALERT: warning, description = close_notify.
java.io.IOException: Server returned HTTP response code: 401 for URL: https://ww3.mydomain.com/
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(HttpURLCon
nection.java:709)
at java.net.HttpURLConnection.getResponseCode(HttpURLConnection.java:238
at java.net.HttpURLConnection.getResponseMessage(HttpURLConnection.java:
304)
at com.sun.net.ssl.internal.www.protocol.https.HttpsURLConnectionOldImpl
.getResponseMessage(DashoA6275)
at SASa.doHTTPTransaction(SASa.java:443)
at SASa.main(SASa.java:79)
CODE
import java.io.*;
import java.io.ByteArrayInputStream;
import java.io.InputStream;
import java.io.IOException;
import java.io.OutputStream;
import java.net.HttpURLConnection;
import java.net.URL;
import java.security.Security;
import java.util.List;
import java.util.ArrayList;
import java.util.Enumeration;
import java.util.HashMap;
import java.util.Iterator;
import java.util.Map;
import java.util.Properties;
import org.jdom.Document;
import org.jdom.input.DOMBuilder;
import org.jdom.output.XMLOutputter;
import org.w3c.tidy.Tidy;
public class SASa
public static void main(String arguments[])
String
region = "",//arguments[0],
username = "",//arguments[1],
password = "",//arguments[2],
accountNumber = "",//arguments[3],
speed = "",//arguments[4],
ispCode = "WN";
List
cookies = new ArrayList();
try
// These two lines add the JSSE service provider into the runtime so that we can do HTTPS.
System.setProperty("java.protocol.handler.pkgs", "com.sun.net.ssl.internal.www.protocol");
Security.addProvider(new com.sun.net.ssl.internal.ssl.Provider());
// BEGIN: Step 1
// Request the first page to get a required cookie.
URL
u0 = new URL("https://ww3.mydomain.com/");
Properties
h0 = new Properties(),
p0 = new Properties();
Map
r0 = null;
h0.setProperty("User-Agent", "Mozilla/4.0 (compatible; MSIE 5.5; Windows NT 5.0)");
p0.setProperty("Username", "user");
p0.setProperty("Password", "pwd");
r0 = doHTTPTransaction(u0, "POST", h0, p0);
dumpResponse(r0);
// END: Step 1
// BEGIN: Step 2
URL
u1 = new URL("https://ww3.mydomain.com/page2");
Properties
h1 = new Properties(),
p1 = new Properties();
Map
r1 = null;
h1.setProperty("User-Agent", "Mozilla/4.0 (compatible; MSIE 5.5; Windows NT 5.0)");
h1.setProperty("Content-Type", "application/x-www-form-urlencoded");
h1.setProperty("Proxy-Connection", "Keep-Alive");
// Set the cookie for THIS request using the cookie received from the LAST response...
cookies.addAll((List)((Map)r0.get("headers")).get("Set-Cookie"));
System.out.println("setting cookie: " + constructCookieHeaderValueString(cookies));
h1.setProperty("Cookie", constructCookieHeaderValueString(cookies));
p1.setProperty("Username", "user");
p1.setProperty("Password", "pwd");
r1 = doHTTPTransaction(u1, "POST", h1, p1);
dumpResponse(r1);
URL
u2 = new URL("https://ww3.mydomain.com/page3");
Properties
h2 = new Properties(),
p2 = new Properties();
Map
r2 = null;
h2.setProperty("User-Agent", "Mozilla/4.0 (compatible; MSIE 5.5; Windows NT 5.0)");
h2.setProperty("Content-Type", "application/x-www-form-urlencoded");
h2.setProperty("Proxy-Connection", "Keep-Alive");
System.out.println("setting cookie: " + constructCookieHeaderValueString(cookies));
h2.setProperty("Cookie", constructCookieHeaderValueString(cookies));
p2.setProperty("__Click", "");
r2 = doHTTPTransaction(u2, "GET", h2, p2);
dumpResponse(r2);
System.exit(1);
// END: Step 2
// BEGIN: Step 3
URL
u3 = new URL("https://ww3.mydomain.com/page4");
Properties
h3 = new Properties(),
p3 = new Properties();
Map
r3 = null;
h3.setProperty("User-Agent", "Mozilla/4.0 (compatible; MSIE 5.5; Windows NT 5.0)");
h3.setProperty("Content-Type", "application/x-www-form-urlencoded");
h3.setProperty("Proxy-Connection", "Keep-Alive");
// Set the cookie for THIS request using the cookie received from the LAST response...
System.out.println("setting cookie: " + constructCookieHeaderValueString(cookies));
h3.setProperty("Cookie", constructCookieHeaderValueString(cookies));
r3 = doHTTPTransaction(u3, "GET", h3, p3);
dumpResponse(r3);
System.exit(1);
// END: Step 3
catch (Exception e)
e.printStackTrace();
* Executes the HTTP request for a given URL, using a given HTTP method, given a set of form
* variables (aParameterSet) and HTTP headers.
private static Map doHTTPTransaction(URL aURL, String aMethod, Properties aHeaderSet, Properties aParameterSet)
Map
result = new HashMap();
try
HttpURLConnection
connection = (HttpURLConnection)aURL.openConnection();
connection.setFollowRedirects(true);
connection.setRequestMethod(aMethod);
setHeadersForConnection(connection, aHeaderSet);
connection.setDoOutput(aMethod.equals("POST") ? true : false);
connection.connect();
System.out.println("\n\nConnected to '" + aURL + "'.");
if (aMethod.equals("POST"))
pushQueryStringToConnection(connection, constructQueryString(aParameterSet));
result.put("response", connection.getResponseMessage());
result.put("headers", getResponseHeadersFromConnection(connection));
result.put("body", getResponseBodyFromConnection(connection));
catch (Exception e)
e.printStackTrace();
return result;
* Sets the HTTP request headers from a set of key/value pairs.
* TODO: This works fine for SAS, but probably needs to be made more robust for multi-value headers.
private static void setHeadersForConnection(HttpURLConnection aConnection, Properties aHeaderSet)
try
Enumeration
headerNames = aHeaderSet.propertyNames();
String
headerName = null,
headerValue = null;
while (headerNames.hasMoreElements())
headerName = (String)headerNames.nextElement();
headerValue = aHeaderSet.getProperty(headerName);
aConnection.setRequestProperty(headerName, headerValue);
catch (Exception e)
e.printStackTrace();
* Builds a multi-value (cookie) HTTP header string from a set of strings.
private static String constructCookieHeaderValueString(List aValueList)
String
result = null,
value = null;
StringBuffer
buffer = new StringBuffer();
for (int x = 0; x < aValueList.size(); x++)
value = (String)aValueList.get(x);
buffer.append(value.substring(0, value.indexOf(';')));
if ((x + 1) < aValueList.size())
buffer.append("; ");
result = buffer.toString();
return result;
* Builds a multi-value HTTP header string from a set of strings.
private static String constructHeaderValueString(List aValueList)
String
result = null;
StringBuffer
buffer = new StringBuffer();
for (int x = 0; x < aValueList.size(); x++)
buffer.append((String)aValueList.get(x));
if ((x + 1) < aValueList.size())
buffer.append(",");
result = buffer.toString();
return result;
* Builds an HTTP query string from a set of key/value pairs.
* TODO: This works fine for SAS, but probably needs to be made more robust for multi-value keys.
private static String constructQueryString(Properties aParameterSet)
String
result = null;
StringBuffer
buffer = new StringBuffer();
Enumeration
propertyNames = aParameterSet.propertyNames();
String
propertyName = null,
propertyValue = null;
while (propertyNames.hasMoreElements())
propertyName = (String)propertyNames.nextElement();
propertyValue = aParameterSet.getProperty(propertyName);
buffer.append(propertyName);
buffer.append("=");
buffer.append(propertyValue);
if (propertyNames.hasMoreElements())
buffer.append("&");
result = buffer.toString();
return result;
* Writes a pre-formatted query string to the OutputStream for a request to the server.
private static void pushQueryStringToConnection(HttpURLConnection aConnection, String aQueryString)
try
OutputStream
out = aConnection.getOutputStream();
System.out.println("\nSending query string: " + aQueryString);
out.write(aQueryString.getBytes());
out.flush();
out.close();
catch (Exception e)
e.printStackTrace();
* Gets the response headers returned by the server as a result of the request.
private static Map getResponseHeadersFromConnection(HttpURLConnection aConnection)
Map
result = new HashMap();
try
String
headerName = null;
List
headerValues = null;
boolean
headers = true;
int
i = 1;
while (headers == true)
headerName = aConnection.getHeaderFieldKey(i++);
if (headerName != null)
if (result.get(headerName) == null)
headerValues = new ArrayList();
else
headerValues = (List)result.get(headerName);
headerValues.add(aConnection.getHeaderField(headerName));
result.put(headerName, headerValues);
else
headers = false;
catch (Exception e)
e.printStackTrace();
return result;
* Reads the InputStream to get the body content returned by the server as a result of the request.
private static Map getResponseBodyFromConnection(HttpURLConnection aConnection)
Map
result = new HashMap();
try
int
i = 0;
InputStream
in = aConnection.getInputStream();
StringBuffer
buffer = new StringBuffer();
while(i != -1)
i = in.read();
if (i != -1 )
buffer.append((char)i);
in.close();
String
body = buffer.toString();
result.put("raw", body);
result.put("xml", getBodyAsXML(new ByteArrayInputStream(body.getBytes())));
catch (Exception e)
e.printStackTrace();
return result;
private static Document getBodyAsXML(InputStream anInputStream)
Document
document = null;
try
DOMBuilder
builder = new DOMBuilder();
Tidy
tidy = new Tidy();
tidy.setQuiet(true);
tidy.setXmlOut(true);
tidy.setOnlyErrors(true);
tidy.setShowWarnings(false);
// OPTIONAL STUFF
tidy.setDropEmptyParas(true);
tidy.setDropFontTags(true);
tidy.setMakeClean(true);
document = builder.build(tidy.parseDOM(anInputStream, null));
catch (Exception e)
e.printStackTrace();
return document;
* Prints out the entire response received by executing the HTTP request to the server.
private static void dumpResponse(Map aResult)throws Exception
System.out.println("Printing Data \n\n");
dumpResponse((String)aResult.get("response"));
dumpResponseHeaders((Map)aResult.get("headers"));
dumpResponseBody((Map)aResult.get("body"));
* Prints out the response (i.e., "OK", "NOT FOUND", etc.) received by executing the HTTP request to the server.
private static void dumpResponse(String aResult)throws Exception
System.out.println("DUMPING RESULT");
FileWriter fw = new FileWriter("output.txt", false);
Writer out = new BufferedWriter(fw);
out.write("------------------------------------------------------------------------------------------\n");
out.write("RESULT: \n");
out.write(aResult);
out.write("\n------------------------------------------------------------------------------------------\n");
out.flush();
out.close();
fw.close();
* Prints out the headers received by executing the HTTP request to the server.
private static void dumpResponseHeaders(Map aHeaderSet)throws Exception
System.out.println("DUMPING HEADERS");
FileWriter fw = new FileWriter("output.txt", true);
Writer out = new BufferedWriter(fw);
out.write("------------------------------------------------------------------------------------------\n");
out.write("HEADERS: \n");
Iterator
iterator = aHeaderSet.keySet().iterator();
String
headerName = null;
List
headerValues = null;
while (iterator.hasNext())
headerName = (String)iterator.next();
headerValues = (List)aHeaderSet.get(headerName);
for (int x = 0; x < headerValues.size(); x++)
out.write(headerName + ": " + headerValues.get(x) + "\n");
out.write("\n------------------------------------------------------------------------------------------\n");
out.flush();
out.close();
fw.close();
* Prints out the body received by executing the HTTP request to the server.
private static void dumpResponseBody(Map aBody)throws Exception
System.out.println("DUMPING XML");
XMLOutputter
outputter = new XMLOutputter("\t", true);
FileWriter fw = new FileWriter("file.txt", false);
Writer out = new BufferedWriter(fw);
out.write(aBody.get("raw").toString());
out.flush();
out.close();
fw.close();The code that actually fails is:
* Writes a pre-formatted query string to the OutputStream for a request to the server.
private static void pushQueryStringToConnection(HttpURLConnection aConnection, String aQueryString)
try
OutputStream
out = aConnection.getOutputStream();
System.out.println("\nSending query string: " + aQueryString);
out.write(aQueryString.getBytes());
out.flush();
out.close();
catch (Exception e)
e.printStackTrace();
I get an HTTPS connection without any problem but I can't send any additional data. 1.3 Works without any problem. 1.4 sends a different protocol(TLSv1) than 1.3(SSL). Is there a way to change the protocol to SSL? Or do I need to use sockets.
The code included in my first post should work for any https site but how can I send username and password information. The server I am hitting does not appear to use TLSv1 as a protocol. -
Midisport 2x2 on osx 10.5.8 fails (but works in Fusion with Vista)
Windows definitely wins this one. On the same machine, Windows just works. The Mac, not so much.
I installed the midisport mac drivers, and after that the lights on the device turned on. So far so good.
But:
GarageBand shows 0 midi inputs
Audio Midi Setup shows no midi input
MIDI Monitor shows no midi inputs
The hardware is correctly cabled. I'm using VMWare Fusion with Windows Vista on the same machine, and midi input works in Windows with a program called Anvil Studio. I can record midi from my keyboard (but with a huge delay).
VMWare Fusion is the only Mac program that notices that the midi adapter is there. The menus shows: Virtual Machine/USB/Connect Midiman USB Device.
Any suggestions for other things to try? How can I verify that the driver is properly loaded? I see this:
root 116 0.0 0.2 137576 6772 ?? S 9:55AM 0:00.43 /Library/StartupItems/M-Audio Firmware Loader/MAFL
How do you get a list of usb devices on a Mac? System Profiler shows it as a Composite Device (I think). No further info available. If VMWare Fusion can see that it's a Midiman USB Device, why can't System Profiler tell what it is?
Another wrinkle: Besides working in Vista with Anvil Studio, I haven't found another Windows utility that sees the midi input. For example, MIDI-OX tells me there is no midi device.
Hardware:
midisport 2x2
MacBook Pro osx 10.5.8
Yamaha P-90 keyboardhttp://www.m-audio.com/index.php?do=support.drivers&f=847 there is something you need to load for this little piece of plastic.
-
PHP Connection fails, but works over saprfc_test.php
Hi,
I can make a connection to SAP using saprfc_test.php but when I try and do this with my php script at the command line it fails with this error:
C:\Documents and Settings\arundelr>php -c C:\www_root\Apache2.2\php.ini C:\www_r
oot\htdocs\newphpsaprfc\parser.php
Order Number: 0000427138
PHP Warning: RFC Error Info :
Group : 102
Key : RFC_ERROR_COMMUNICATION
Message : Connect to message server failed
Connect_PM MSHOST=sapdev.host.com, R3NAME=FRD, GROUP=PUBLIC
LOCATION CPIC (TCP/IP) on local host
ERROR Group PUBLIC not found
TIME Mon Jul 09 17:28:30 2007
RELEASE 640
COMPONENT LG
VERSION 5
RC -6
I do not specify a group when I use saprfc_test.php but I notice this is reporting it as PUBLIC. Does anybody have any bright ideas?
cheers
Rob.
MODULE lgxx.c
LINE 3531
DETAIL LgIGroup
COUNTER 1
in C:\www_root\htdocs\newphpsaprfc\includes\processor.php on line 15
RFC connection failed
C:\Documents and Settings\arundelr>specifying "MSHOST"=>"", did the trick.
-
Create index fails (but worked previously)
oracle 8.1.6 / solaris 7
I installed InterMedia a few weeks ago (after many problems with configuring
the listener and tnsnames) and created 3 text indexes on 2 tables(one column
being a CLOB). The searches worked great (using "contains"). Next I tried to
create a preference using ctx_ddl.create_preference andctx_ddl.set_attribute
to allow for streaming of docs on the server. When Itried to create the index
on the docs, it failed, giving me the
ORA - 29885 error.
Today, I needed to truncate the tables I created with the 3 indexes; in order
to do so, I had to drop the index (FORCE) and when trying to recreatethem, it
failed, giving me the error below. IT WAS WORKING 2 WEEKS AGO! WHAT
HAPPENED??? The metalink site does not have good info and is TOO slow.
nullhere's the error message:
ORA-29855:error occurred in the execution of ODCIINDEXCREATE routine
ORA-20000:interMedia Text error: DRG-50704: Net8 listener is not running or
cannot start external procedures ORA-28575: unable to open RPC connection to
externalprocedure agent ORA-06512: at "CTXSYS.DRUE", line 126 ORA-06512: at
"CTXSYS.TEXTINDEXMETHODS", line 54 ORA-06512: at line 1
oracle 8.1.6 / solaris 7
I installed InterMedia a few weeks ago (after many problems with configuring
the listener and tnsnames) and created 3 text indexes on 2 tables(one column
being a CLOB). The searches worked great (using "contains"). Next I tried to
create a preference using ctx_ddl.create_preference andctx_ddl.set_attribute
to allow for streaming of docs on the server. When Itried to create the index
on the docs, it failed, giving me the
ORA - 29885 error.
Today, I needed to truncate the tables I created with the 3 indexes; in order
to do so, I had to drop the index (FORCE) and when trying to recreatethem, it
failed, giving me the error below. IT WAS WORKING 2 WEEKS AGO! WHAT
HAPPENED??? The metalink site does not have good info and is TOO slow.
null -
VPN connect via menu extra fails, but works via prefpane - anybody else?
Is anybody out there with the same symptom, getting an error message when trying to establish a VPN connection via VPN menu extra but being able to connect properly via networking prefpane? Would be interesting to know if this could be a bug worth sending a report to Apple...
PB G4, Mac OS X 10.5.5Tim, you made it. Another example for that famous tricky problems after OS migration. I had the VPN prefs already on Mac OS X 10.4 and trusted them on Mac OS X 10.5 after their automatic
adoption too...
Thx mate! -
"scan to network folder" suddently stopped working after many months of no issues
scan to network folder was working fine over a wireless network to a folder on my file server - for many months.
This weekend I noticed the printer said it was "updating".
I guess it must have done some kind of automated update or something because I did not initiate an update.
Suddenly scan to network folder fails to work.
When I try from the printer, it says cannot connect to \\computer\folder
When I test from the embedded web server on the printer "Connection Failed"
The folder is online. I can access it from another computer.
I have also tried setting up a second folder config using the IP address as \\x.x.x.x\folder(The first 3 sets of digits in the IP addresses are the same for printer and network server) I even tried setting up anoter account to authenticate to the file server with a simpler password for testing purposes to rule out typographical errors. I have tried bouncing the printer, the router, the network server and the wireless access point all to no avail. It looks like the printer is failing to find the network server anymore.Pity there is no "ping" option on the printer to test if it can even see the network server anymore. I can "scan to computer" to another computer on the wirless network.But I like the convenience of being able to scan to a defined network folder whether my other computer is turned on or not. Does anyone know if HP pushed out a printer update this week or something?Just wondering why it suddenly changed.Download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&ju...
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Hi I installed a new hard drive in my Mac mini osx lion an when I turn it on I get a flashing file with a question mark. I tried holding command and R keys when turning it on but the recovery fails to work. I can hold the option key at start up and choose my network, then Internet recovery shows up with an arrow pointing up. When I click on the arrow Internet recovery fails and all I get is a globe with a triangle on it with an exclamation mark on it, and under that it says
apple.com/support
-6002F
Does any one know how I can fix this without a recovery disc? ThanksI just want to add to this, in case someone else searches for this error on Apple Support (google doesnt cover apple support.. how clever is that?)
I had the same error. And i had a Computer that had worked, with a SSD drive and 16GB upgrade done by the owner himself.
I tried swapping with a Mechinal Harddrive, no luck.
Kept the Mechanical drive in, and tried with some other Ram, it worked..
So for me this error and after reading the other responses can be boiled down to a Harddrive problem or Ram issue.
It was Ram for me.. -
Hi, my mail applicatin is not working properly. It says cannot get main...the connection to the server failed but everything else is working ok. How can I solve this problem?
The connectivity test indicated that there was a problem with the user's ActiveSync folder, typically fixed by checking the box "Allow inheritable permissions ...".
Since it already was checked and even by removing the inherited permissions and then re-inheriting them didn't do the trick, I ended up just deleting the whole thing and then made a new duplicate account and blank mailbox. That was pretty drastic
but it fixed the problem. After restoring his mailbox contents from backup, the user is now a happy camper.
The connectivity test tool was helpful because the external URL was blank so I filled in the URL. But ActiveSync was working fine for everybody without the URL before although I don't know why it did work without it.
The other funny thing is on one of my iPads I am able to synch my mailbox and also the user's mailbox but on another iPad it just wouldn't synchronize when it worked before I added the external URL. The iPads have the same OS version so I
just don't understand it. Oh well.
Thanks for your help. That was a good tip!
WC -
Cannot get FaceTime to work on my mini. Gives network error. But all other devices work .
I Cannot get FaceTime to work on my mini. It gives me a network error. But all my other devices work fine.
Quite a few people have posted about having issues with Facetime and iMessages over the past few weeks. The update to iOS 8.1.3 was supposed to address those issues and you could try updating your iPad. But the fix didn't work for everybody.
IF you are getting the message about checking your network connection, start with these very basic troubleshooting steps.
Check Settings>General>Date & Time>Set Automatically>On. Make sure that the time zone setting is also set correctly.
If that didn't solve the problem, restart your iPad and try again. If that fails, reset your iPad and try again.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
Maybe you are looking for
-
Someone please help the kid locked me outa my new ipad and says cant remember the numbers i cant lose any files nd no longer have computer that set it up help me (did i mention he can destroy a anvil with a 16oz.hammer)
-
Inserting PDF in Word Document
In previous versions of MS Word and Adobe (Specifically Word 2010 and Adobe 8 & 9), I could insert a PDF file in a Word document. This no longer works using Word 2010 and Adobe X. Is there some other way to do this? Now I can only insert the PDF as a
-
Data dictionary table where the structure of table is stored ???
hi does anyone have idea where the structure of created table is stored in data dictionary. I have idea like where constraints are stored,indexes are stored etc. But I am looking if there is any data dictionary table which has this information too..
-
Business packages for BO in portal
Hi Team, I wanted to know if there are any business packages for Business objects which can be implemented in Portal. i tried to search in market place but am not able to find much. regards Bharat
-
Can I down load movies to my new iPod nano
can I down load movies to my new iPod nano