NETWORK OUT OF ORDER

according to this http://btsc.webapps.blackberry.com/btsc/dynamickc.do?externalId=KB13324&sliceID=1&command=show&forwa...
i should change the Network Send over.. but it doesnt say GPRS..
my phone only have options:
..circuit switched
..circuit switched preferred
..packet switched preferred
..packet switched
please help.thankss!!

this solution has worked for me:
go into text messages (click menu button) click options, change "send text-only message as:" from "Always SMS" to "Always MMS". then try to text a contact, it has worked for me

Similar Messages

Cause 1 = 0x82A6 Network out of order - ISDN error

When we are try to make outgoing call, we are getting the below error :
cause 1 = 0x82A6 Network out of order
Incoming call there is no problem in the Same E1 PRI line, ISP saying there is no problem from thier side.

We are using h323 gateway. When I am using csim start the outgoing calls fails
ISA-VG1#un all
All possible debugging has been turned off
ISA-VG1#csim start 93XXX6306
csim: called number = 93XXX6306, loop count = 1 ping count = 0
csim err csimDisconnected recvd DISC cid(570049)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0
Router#sh gateway
H.323 ITU-T Version: 4.0   H323 Stack Version: 0.1
H.323 service is up
This gateway is not registered to any gatekeeper
Alias list (CLI configured) is empty
Alias list (last RCF) is empty
ISA-VG1#csim start 93XXX6306
csim: called number = 934466306, loop count = 1 ping count = 0
*Feb 5 13:06:47.949 UTC: ISDN Se0/3/0:15 Q931: Sending SETUP callref = 0x3957
callID = 0xCE73 switch = primary-net5 interface = User
*Feb 5 13:06:47.953 UTC: ISDN Se0/3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x
3957
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
        Called Party Number i = 0x80, '34XXX6306'
                Plan:Unknown, Type:Unknown
*Feb 5 13:06:48.049 UTC: ISDN Se0/3/0:15 Q931: RX <- SETUP_ACK pd = 8 callref
= 0xB957
        Channel ID i = 0xA9839F
                Exclusive, Channel 31
csim err csimDisconnected recvd DISC cid(570048)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0
ISA-VG1#
*Feb 5 13:06:48.049 UTC: ISDN Se0/3/0:15 Q931: RX <- CALL_PROC pd = 8 callref
= 0xB957
        Progress Ind i = 0x8288 - In-band info or appropriate now available
*Feb 5 13:06:48.097 UTC: ISDN Se0/3/0:15 Q931: RX <- RELEASE pd = 8 callref =
0xB957
       Cause i = 0x82A6 - Network out of order
*Feb 5 13:06:48.097 UTC: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callr
ef = 0x3957
Incoming calls are perefect, Please let me know the problem is from ISP Side ?

Network out of order (38)

Hi have a 1760 router. I can make call but i can not receive calls and send me this error:
dur 00:00:00 tx:0/0 rx:0/0 26 (network out of order (38))
IP 0.0.0.0:0 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g729r8 pre-ietf
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
240B : 2007 1001116340ms.2006 +-1 +130 pid:96300 Originate 6301
dur 00:00:00 tx:0/0 rx:0/0 26 (network out of order (38))
IP 0.0.0.0:0 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g729r

Who is calling you, using what protocol, and what the router is supposed to with the call ?

"Network out of order" and "Short message transfer rejected"

Guys,
I have a BB 9300 3G Curve and I have trouble sending SMS. This is a peculiar problem since I
#1 am able to send an SMS problem free sometime
#2 get an error message saying "Network out of order"
#3 get an error message saying "Short message transfer rejected"
Plus, this problem is not specific to a particular contact number. I get different messages (1,2,3 above) for the same number at different times. I have tried putting my SIM in a different handset and it works perfectly fine.
Someone please HELP!

Simply try pulling out the battery and leaving it out for a couple minutes. Usually, that is the fix-all to glitches. If not, you should contact your wireless mobile provider and see if they can help you. Usually, they are very easy to get along with and want to help you. But I think the battery pulling out will help you. It's happened to me before and I had to do that.

Sms network out of order for one contact

I have had my curve for a while and i cannnot seem to send an sms to one of my contacts only as oit comes up with the network out of order error message! Help Please

Step 1: Remove your battery while your phone is powered on then replace it a few seconds later.
Step 2: Try once again to send that contact an SMS.
Step 3: Thank me for the helpful advice and have a good life with your new-found happiness.
(After that, I really hope my suggestion works!)
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

Phone keeps on telling me network out of order

Help! Everytime I try to send sms on my z10 it keeps on telling me network out of order. This is the first time that it has happened to me and it's really bothering me. How can I fix this?

That seems strange. Try registering your phone on the network once again.
To do this, swipe down from the top of your homescreen and select Settings>About and switch the Category menu to Network. Next, press the three dots in the bottom right corner and register your phone again.
Try that and post back with your results.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

SMS: Network out of order

I got my blackberry curve 8520 on friday, o2 contract, registered it all, sorted and working, then on sat swapped my pay and go number to my contract number so i wouldn't have to tell everyone. they said it would take 24 hours to swap so i wouldn't be able to text which i was fine about.
Its now been more then 24 hours and whenever i try to send an SMS i shows a X and says "Network out of order". I can email, blackberry messenger, call, facebook send and recieve etc. only thing i cant do is send a SMS??
Pulled battery out and SIM. But will not work.
Anyone got any ideas?
Thanks

Get your sms service number from your service provider, google it.
1. Go to options
2. go to sms
3. service center and change the number to the right service number.
Hopefully this will work for you.

CUCM and H323 gateway-Cause i = 0x80A6 - Network out of order

Hi,
I cant get calls into the CUCM from a H323 gateway. Incoming external calls here out of service message or Number Unobtainable. I've attched logs if anyone can help?
Rich

Hi Alex,
Thanks for reply. I should've attached the full config as it shows the Translation Rules. See below.
Can anyone help?
voice translation-rule 2
rule 1 /^56/ /5\2/
rule 2 /^6/ /5/
rule 3 /2/ /52/
voice translation-rule 3
rule 1 /^1$.........$$/ /01\1/
rule 2 /^2$.........$$/ /02\1/
rule 3 /^7$.........$$/ /07\1/
rule 4 /^8$.........$$/ /08\1/
rule 5 /^4$......$$/ /01914\1/
rule 6 /^2$......$$/ /01912\1/
voice translation-rule 6
rule 1 /^[1-9]/ /90\0/ type international international
voice translation-rule 7
rule 1 /^1/ /901/
rule 2 /^2/ /902/
rule 3 /^3/ /903/
rule 4 /^4/ /904/
rule 5 /^5/ /905/
rule 6 /^6/ /906/
rule 7 /^7/ /907/
rule 8 /^8/ /908/
rule 9 /^9/ /909/
voice translation-profile INCOMING
translate calling 7
translate called 2
voice translation-profile OUTGOING
translate called 3
voice-card 0
dsp services dspfarm
interface FastEthernet0/0
ip address 192.168.178.66 255.255.255.192
ip pim dense-mode
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr 192.168.178.66
interface FastEthernet0/1
no ip address
duplex auto
speed auto
no keepalive
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
control-plane
voice-port 0/1/0
translation-profile incoming INCOMING
compand-type a-law
cptone GB
description ISDN2 .......... lines 1+2
voice-port 0/1/1
translation-profile incoming INCOMING
compand-type a-law
cptone GB
description ISDN2 .......... lines 3+4
ccm-manager music-on-hold
mgcp fax t38 ecm
dial-peer cor custom
dial-peer voice 999 pots
destination-pattern 999
port 0/1/0
forward-digits all
dial-peer voice 9991 pots
destination-pattern 999
port 0/1/1
forward-digits all
dial-peer voice 112 pots
destination-pattern 9112
port 0/1/0
forward-digits 3
dial-peer voice 1121 pots
destination-pattern 9112
port 0/1/1
forward-digits 3
dial-peer voice 9999 pots
destination-pattern 9999
port 0/1/0
forward-digits 3
dial-peer voice 99991 pots
destination-pattern 9999
port 0/1/1
forward-digits 3
dial-peer voice 100 voip
preference 2
destination-pattern 52...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.0.150
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 101 voip
preference 1
destination-pattern 52...
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.203.20
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 1 pots
translation-profile outgoing OUTGOING
preference 3
destination-pattern 0T
translate-outgoing called 10
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/0
forward-digits all
dial-peer voice 11 pots
translation-profile outgoing OUTGOING
preference 4
destination-pattern 0T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 9 pots
translation-profile outgoing OUTGOING
preference 1
destination-pattern 9T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/0
forward-digits all
dial-peer voice 91 pots
translation-profile outgoing OUTGOING
preference 2
destination-pattern 9T
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 2 pots
translation-profile outgoing OUTGOING
destination-pattern 2......
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 21 pots
translation-profile outgoing OUTGOING
destination-pattern 2......
incoming called-number .
fax rate disable
direct-inward-dial
port 0/1/1
forward-digits all
dial-peer voice 52982 voip
preference 1
destination-pattern 562982
progress_ind setup enable 3
voice-class codec 1
voice-class h323 1
session target ipv4:192.168.0.150
dtmf-relay h245-alphanumeric
no vad

My blackberry curve 8530 keeps saying the network is out of order?

I was at camp all week and had it turned off and when I got home and turned it on I tried textiing my friend and call my parents but it kkept saying that my network was out of order? I dont quite understand and I've taken the battery out and everything I'm not sure what to do and I really need my phone. Help?

Hi brittany097,
Welcome to the Support Community!
The following KB article should provide more information on the error message you receiving. "Network out of order error message received when sending an SMS message" http://bbry.lv/GGTq5j
Hope this helps.
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

Final Cut Express occasionally renders audio "out of order"

I'm running into a very occasional problem, which is just rare and random enough to not be recreatable on demand, and so is proving difficult to troubleshoot.
In a nutshell, sometimes - not very often - when I render an audio stream it will report an estimate of 6 hours or more for something even as small as a 1-second transition. This is not a composite or layered video or audio by any means, just a standard cross-disolve/cross-fade (+3) between two adjacent clips. When this type of extreme estimate occurs, I may find afterward that rendered audio in the sequence has been moved around, sort of like a shell game. Usually this anomaly only happens over a minute or less of the project. Trying to describe this, a portion of the rendered audio from one part of the timeline will replace a portion of rendered audio elsewhere -- as if some audio render segments have gotten linked out-of-order. If memory serves, the displaced audio so far has always appeared earlier in the timeline than it should. The replaced audio just doesn't seem to appear anywhere. So far, if I remove the associated audio render files and re-render, it fixes the problem, but I'm trying to sort out what is causing the behaviour in the first place so that I can take steps to keep it from happening at all. It raises havoc with trying to meet deadlines when I'm stuck re-rendering sometimes entire segments....
For some details about the environment:
     System is a Mac Book Pro, 2.4GHz Intel core duo, 4GB RAM, OSX 10.5.8.
     I'm using FCE4, importing SD clips for TV production from Sony cameras (sorry, I'm not part of the camera crew, and I can't recall the exact model number of their cameras - they are all the same model though, configured the same, so no known variables from that end).
     The cameras record standard-def MPG (Mpeg layer 2, so yes I convert them before importing into FCE), I convert them using the ffmpeg library. I tried FFMPEGX, but I find I have far more control over video/audio parameters and combinations with the command-line version. The parameters I use result in a Quicktime (.mov) file with these parameters: 16-bit integer (little-endian), stereo, 48kHz, DV 720x480 (640x480), Millions (of colors). FCE is generally quite happy with these parameters, and does not require immediate rendering of the audio or video - unless plugins are applied of course. As far as plugs, I generally only use the built-in FCE plugs for comp/lim and parametric EQ. If I have to get much more detailed than that, I'll go to Digital Performer (read on).
     In some cases the audio of the original clips is in quite a bad state, and requires far more detailed restoration than FCE can provide. As I am primarily an audio engineer, I rely on Digital Performer and friends for audio restoration, exporting from there a new clip, usually duplicating the original video (self-contained), though sometimes I do let DP export a reference movie. Final Cut doesn't seem to have any trouble with the .mov files exported from DP either way, and this anomaly doesn't seem to care whether the clips involved were processed by DP or not.
     Disk space, memory, and CPU load are all well within acceptable ranges; and with my previous years of experience as a systems admin, I am well aware of the system impact and ramifications of using internal vs external disks, memory allocation, disk filesystem operating overhead, etc.
As I've mentioned, this is not a show-stopper, I have a work-around to correct it when it happens. It's just a bit of a bugger *when* it happens, and I really wish I could work out the root cause of it, so that I can take steps to avoid the problem in the first place. Any suggestions/insight/help would be greatly appreciated, thank you! :-)

Thank you for your response.
Grr. I had a nice response ready to post, and apparently the system logged me out and wouldn't let me log in while keeping the text. I'll condense it a bit, since I've stumbled across some additional points to ponder while typing.
The clip:
And the sequence:
Yes, I see that the clip is 16-bit integer and the sequence supports 32-bit float, but this should not pose a problem since modern digital audio processing up-converts smaller sample formats to larger ones on the fly for processing, and exports whatever format is desired at the end. If this *was* the problem, I should always be off by a ratio of 2:1 on all audio data, but I'm not.
Additional notes: the system generally has Firewire, USB, and network mounts (all required for my work), and the internal drive (which *is* 7200RPM) is partitioned into a system and a user area to keep audio and video projects out of the system's disk space. Most main clips for a project are placed on the internal user space for speed, externals hold auxilliary files (stills, adverts, livetype, etc).
It was at this point in my previous typing that I began to realise that the anomaly seems to begin in sync with some random livetype object. It then extends a bit past the livetype object, so it's not locked to that object; and multiple instances of the same livetype object DO NOT result in multiple instances of the audio anomaly; it only hits a single instance; and again it usually cleans up when the audio render files are removed and re-processed.
This leads me to wonder about a possible odd combination of events/processes on the system, and whether or not FCE handles livetype natively or requires a livetype helper (i.e., another process stuffed into the system table). This sort of external influence would be a transient sort of event, and therefore could easily be out of the way by the time second render attempt is begun - resulting in the "fix" by removing and re-generating audio render files.
It makes sense to me, but it's still hypothesis and supposition at this point.

Facebook application is out of order.

I loaded new update by Facebook application. After then loading, Facebook application has been out of order. O wanna use the application but not open. this application alerts network error

Here is the link to Apple's Knowledge Base article on troubleshooting portables that won't turn on or start up:
http://docs.info.apple.com/article.html?artnum=50959
If nothing there helps, try plugging it in with the adapter and picking it up in your left palm to the left of the trackpad and squeeze the case there between your palm and left thumb as you push the power button. Do not let up the pressure on the case. Continue applying this pressure as for several minutes in an attempt to start up. Does pressure on the case there allow it to start up?

Option key is out of order when I want to select a boot disk

I've upgraded the OsX10.6.8.
after then, I can't boot by Bootcamp any more, because the Option key is out of order. I've tried it over 10 times. What's wrong?

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.

Images Out of Order

Heya;
I just headed over to my "All Images" folder, which I do not do often, only to find that the images were out of order and some of them are missing "Date Created" listings. Also, there are no "Size" listings. So I opened "Arrange By" and the "Size" and "Label" options were dimmed or hazed over. How do I fix this problem?
Blessings,
Damon

Now I just got a sudden "we have detected trojans on your pc" WINDOWS SECURITY ALERT clamming down my safari scan page while checking out "old mac pin wheel cursors" on my mac. It looks exactly like the "my computer" page on a windows machine, complete with the proper icons which can be clicked but don't do anything page. What is this and why did it show up now? According to this thing I am on a windows machine that has exactly 299 trojans. Text version below.
System Tasks
View system information
Add or remove programs
Change a settings
Other Places
My Network Places
My Documents
Shared Documents
Control Panel
Details
My Computer
System Folder
System scan progress
Found 58 trojans
Shared Documents
Found 54 trojans
My Documents
Hard drives
Found 270 trojans
Local Disk (C:)
Found 17 trojans
Local Disk (D:)
DVD
DVD-RAM Drive (E:)
100%
Scan complete. 399 fileinfos was found!
Your Computer is Infected!
fileinfos and actions:
Name Risk level Date Files infected State
Trojan-IM.Win16.PS.fp Critical 03/13/2010 15 Waiting removal
Trojan.Win32.SubSys.dr Critical 05/13/2009 23 Waiting removal
Trojan-Clicker.HTML. IFrame.bk Critical 04/17/2010 37 Waiting removal
Description:
This program is potentially dangerous for your system. Trojan-Downloader stealing passwords , credit cards and other personal information from your computer.
Advice:
You need to remove this fileinfo as soon as possible!
Full system cleanup
Windows Security Alert
To help protect your computer, Windows Web Security has detected trojans and ready to remove them.
Detected spyware and adware on your computer:Filename:Remove allCancelSpyware is software, which can gather informationfrom user`s computer through Internet connection and sedn them to it`s creator. Gathered information can be passwords, e-mail addresses and all that data, which is important for you.
What on earth is that!

Signature 1330-X: TCP segment out of order - what does it mean?

Hi,
on a customer's site, on one of their IPS, I get a lot of sig 1330 alerts, mainly those two:
1330-12: TCP segment is out of order. If the signature status is set to disabled, the packet will be passed to all engines that are not stream based.
This signature will not produce an alert in promiscuous mode regardless of the signature status.
1330-17: TCP segment out of state order. If a packet in a stream causes this signature to produce an alert, processing will cease for that stream. This signature will not produce an alert in promiscuous mode regardless of the signature status
I'm not sure how to interpret these alerts correctly and/or how to troubleshoot further. Does anyone have an idea?
Thanks a lot,
Florian

Is your sensor monitoring more than one network segment?
If so then these alarms are common when a TCP connection crosses both networks and gets seen twice by the sensor.
This can confuse the sensor's tracking of the connection.
A common scenario is to have the sensor monitor both the Inside network or a firewall as well as the DMZ. When an internal user connects to the company's web server the traffic gets seen by the sensor both on the Inside network and in the DMZ. The sensor tries to put the packets from both networks together in order to try and monitor it as a single connection. Because the packets get modified by the firewall it often results in inconsitency between traffic on the 2 sides and causes the sensor to be confused about the connection.
The good news is that if this is your problem, then there are 2 easy workarounds.
1) If your sensor supports virtual sensors, then create a second virtual sensor. Assign one network to default vs0, and assign the other network to the new virtual sensor. This way each virtual sensor sees traffic on just one of the networks and won't become confused.
2) If your sensor does not support additional virtual sensors, or you've used up all 4 virtual sensors, then there is a configuration option within the virtual sensor configuration itself:
Inline TCP Session Tracking Mode
By default it is set to Virtual Sensor which is why it tries to put together packets from both networks to try and look at is a single connection and gets confused.
BUT it can also be set to Interface and Vlan. This configuration allows the virtual sensor to treat the traffic on each network independantly. The connection on the first network will be monitored independant of the connection on the second network. This will prevent the virtual sensor from getting confused.
The above is just my guess at what is going on in your network based on what we've seen on other networks. If this doesn't address the reason for the signature triggerings, then please respond back with more information about your network.
It is possible that these could be a hacker trying to avoid detection by the sensor, but more likely something in your deployment is confusing the sensor.

SMS messages out of order

Ever since I upgraded to 1.1.3, my text messages with certain people are out of order. I'll send a message, then when they reply their message will be above mine, like their reply was the original message then I replied. I hope that makes sense. Is anyone else having this problem? Do you know how to fix it? My time is already selected to be set by the network.

That problem was acknowledged by Apple. Their possible solution is go to Settings>General>Date&Time>Set Automatically ON

NETWORK OUT OF ORDER

Similar Messages

Maybe you are looking for