Network printing not working...

Hi there!
I wanted to print a document out of Pages on my Canon IP3000 (connected on an eMac) by using the networkprint function.
But that doesn't work! It appears a Message: "Print error". I added the networkprinter again and again, but that won't help!
Then I tryed to print in TextEdit and MS Word and that worked fine!
Why doesn't Pages print on the IP3000? (On my i450x, connected directly to my iMac it works.)
I hope here are some people who can help me!
Thanks!
Mike.

Like Bonjour, not all printers support IPP (= internet printing protocol) - it started around 1999. Most do support LPD and HP Jetdirect (HP Jetdirect is called raw port 9100 on Windows). The LPD and IPP protocols require us to enter the printer's queue name (also called port name) in the Print & Fax add printer dialog. HP Jetdirect doesn't use queue name.
So, use LPD and find the queue name, or try the HP Jetdirect protocol.
You can go to Windows and printer properties and then to Ports to see the configuration - queue name or port 9100.

Similar Messages

  • Error 0x00000709 Networked printer not working in a home network with HomeGroup enabled.

    I should start by describing my network by device.
    Gateway device - Motorola SB5120 SURFboard cable modem
    Router/WAP device - Linksys Wireless G Broadband Router with 4 port Switch Model: WRT54G v4 Security: WPA2 with firewall.
    Windows 7 Ultimate Desktop with Homegroup enabled (Printer driver installed & ethernet wired)
    Windows 7 Pro Laptop set to homegroup for the Desktop (Ethernet wired and Wireless depending on the situation)
    Windows 7 Home set to homegroup for the Desktop (Wireless)
    Brother Printer Model: HL-2170W (Wireless)
    HP Printer Model: HP Officejet 6500A Plus (Wireless)
    What have I done?
    Installed drivers on 2 of the 3 computers. The final computer (Win7 Home) was added in later and works fine when connecting to the internet through the WAP. However it does not even find the printer when trying to install the driver which is a part of the
    process for driver installation for the Brother Printer.
    I had set up the printer for two of the three computers and had it working at one time however in trying to get the printer set up for the final computer I somehow have messed up those settings.
    During that setup I tried to move the printer to a networked printer (It was shared before and installed on the network with both the Desktop and the Win7Pro lappy able to print but it would not print for the new arrival to the Homenetwork. This caused
    me to seek a solution which involved installing the proper driver in the Win7Home and the discovery that the driver installer could not find the Brother printer at all which prompted the moving of the printer to a networked printer.) (The Win7Home computer does
    not find the HP printer either but that is a can of worms yet unopened.)
    I am sure there are a few things that I did not do correctly and I may have left out some additional information which you may require. If I can help clarify this question please feel free to query me. I thank you in advance for your time and consideration.
    HH

    Hi,
    May I know that are these two network printer with network adapter?  If they are installed on the network, you could add them and install the drivers  for Windows 7.
    Here is one article and two discussions can be referred to.
    Install a printer on a home network
    http://windows.microsoft.com/en-us/windows7/install-a-printer-on-a-home-network
    Error adding printers on windows 7 client after deployment (0x00000709)
    http://social.technet.microsoft.com/Forums/en/w7itproinstall/thread/4979f1a9-f54e-4c5f-8199-c98315dc53cc
    Windows 7 homegroup network printer setup
    http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/windows-7-homegroup-network-printer-setup/43c8417d-1fd5-49e2-bdfc-733844973ddd
    Ivan-Liu
    TechNet Community Support

  • Network print not working

    I recently set up printer sharing between my desktop and laptop computers.  The HP printer I installed on the desktop system via USB connection  was an F4280.  That system is running Vista 64.  Print jobs from the desktop print fine but when I install the shared printer on my laptop it does not print.  The laptop sees the shared printer, appears to print but there is nothing printed.  I paused the printer from the desktop system and resubmit the print job from the laptop and I can see the entry in the printer queue.  When I resume the printer it just disappears - no error messages, no output.  
    I also have an Epson printer that I have done the same process with and it works fine from both computers so it appears the networking is working.   They are connect to a wireless router - Linksys 802.11g 
    What is happening with the HP printer and what can I do to fix it? 

    Hi Dinesh_G,
    Sorry for the delayed response.  Try adding an alternate driver.  Here is a link that will provide steps for that.  Click Here  Check which PCL driver you are currently using and add the alternate (PCL5/PCL6).  Please see the below for additional clarification.
    Utilize the above link for exact steps on adding the driver.
    1. Check which driver currently used-PCL5 or PCL6-this will be located near name of driver in print folder or print properties
    2. Follow steps provided in link to add whichever one the currently installed driver is using
         A.  Select HP as manufactuer
         B.  Select HP universal printing PCL 6 or HP universal printing PCL 5
    3. Attempt duplex print job
    Hope this helps!
    Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
    Please select the "Accept as Solution" button on the post that best answers your question.
    I appreciate your input !
    Thank You,
    I work for HP.

  • Network printer not working

    Should be a simple task... I'm obviously missing something simple.
    I have a HP C4380 inkjet connected to my server (10.6.8) via USB.  If I follow the Apple Printer Admin manual, p25, it says to configure the print queue "enter an IP or DNS name".  I'm using USB.
    SO... I deviate from the manual, and try this: 
    I setup a LOCAL printer, and it recognizes it just fine.  Setup no problem.
    Go back into Print Service, and now I see my printer queue - already setup - but no protocol is checked.  And, my clients (10.6.8) can't see it, unless I check "LPR" and "Show name in bonjour".
    Then, my clients can see it - however, when I add it, I have to manually select the "print using:" driver (c4380), and when sending a test page, the queue on the client simply says "In use" for 2 seconds, then "Paused" forever after.  The server queue doesn't even show a job, nor is there anything in the logs that indicates that a job even came in.
    Please help point me in the right direction,
    Thanks,
    Jason

    Disconnect the USB cable, and plug an ethernet cable into the printer, assign an IP address, and set up a DNS host.  Then follow the rest of the instructions.
    Network printers are far easier to deal with than are host-based printers.  Serving host-based printers to a network is typically more management and more cost for fewer features and with more oddities.

  • Adding shared printers? Network printer not showing up in list

    I have a network printer not showing up in the Bonjour Printer Wizard. There is not a place to add a printer to this list. Does my network printer need to be installed under the Windows side as well, or can I share it using Bonjour? I'm confused as to how the shared printer program works. Also, my Adobe "print to pdf" option shows up as a printer, but how do I change the file destination location? It doesn't give me an option to change the "saved to" location. I am using these printers through Parallels in AutoCad, and that should be the only reason I will need to share printers. But I am in AutoCad a good deal of time, so I need to know how to quickly print my drawings.

    Welcome to the forums!
    You don't say if you installed after downloading the Printer you deleted, but I suspect it's one not showing, and that you need to reinstall.

  • HP Laserjet 1320 attention light on, printer not working.

    I checked for paper jam, reseated printer cartridge, removed and reinserted printer and line cord plugs.  Turned printer on and off.  Attention light remains on and printer not working.

    Hi Robert8695,
    Let's manage one issue at a time. Regarding the error "unable to establish a two-way connection with the device", check out the link below for troubleshooting you can do to resolve it:
    http://goo.gl/u3Snr
    Let me know what happens and if the other problems persist as well.
    If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

  • My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1and it was not jillbreak or hacked to unlock. I need help, what can I do?

    My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1
    my phone was not jillbreak or hacked to unlock. i need help, what can I do?

    Did you do the Reset Network Settings as I described above?
    There is no way to go back. You can try reseating your nanoSIM or replacing it. Or call your cell provider and have them check the provisioning on your phone.
    Or Restore your iPhone from your backup in iTunes.

  • My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1 i need help, what can I do?

    My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !!
    It was working fine on ios 8.1.1 i need help, what can I do?

    I have this problem too - and it is on a BRAND new iPhone 6 - I have definitively tracked the issue to the moment I upgraded to iOS 8.1.2 - and am beyond frustrated. No fix to tell you about, sorry…but you can read my post here if you are into the whole "misery loves company" thing: iOS 8.1.2 Cellular data problem (Definitive - maybe)

  • My Iphone 4 network is not working in Malaysia

    My Iphone 4 network is not working in Malaysia as I offered for 2 month period by behalf of my company and when buy a sim card in Malaysia then I only realise there were no network and I bring to a shop and they upgraded my Iphone and it stuck on the activation part which require a network. Any Solution ?

    iphone 4 and 4S have two microphones...bottom n top...sometimes top microphone is covered by the case or sheet as in my case..and when i just put off the case it was working fine.....i just got problem today and today it is solved again.....may be its ur case or may be ur case is a genuine hardware software problem...just for info

  • Printer not working following iPad uodate

    Printer not working following iPad upgrade

    Hi,
    Is the printer not mechanically working or are you having a problem with printing wirelessly from your device? Was the upgrade to the ipad software or did you get a new ipad?
    Try restarting your apple device - It's a simple fix that sometimes helps re-establish the connection to the printer.
    Other things to check would be that there have been no recent changes to the wifi password.
    "Although I work for HP, I'm speaking for myself and not on behalf of HP"
    "Say "Thanks" by clicking the Kudos Star in the post that helped you.
    --Please mark the post that solves your problem as "Accepted Solution"

  • Wrt610n wireless network does not work after firmeware upgrade

    Hi
    I just updated my Wrt610n hardware version 1 to the newest firmware, it did finish with sucess, I did factory reset reboot and reconfig. But the wireless network does not work , cant connect computers to it. Did downgrade the firmware to the same it was and restore my settings but still wireless does not work. But router works fine with lan.  Any suggestions? maybe the firmware tosted the router?
    Regards
    Stefan

    Update -
    After last reset and reupgrade with the newest firmware for hardware version 1 I could config the router and connect 2 computers with wireless - but only for about 15 mín - then they lost connection and could not reconnect.
    I did then get the newest update for hardeware version 2 - just to try and upgraded with that and got success, and now I have reset the router again and config it and those 2 computers are connected and have been for 1 hour now. So seems to be working - is it okay to have the firmware for hardware version 2 on my version 1 router?
    Any thought what is going on - could it be that the other firmware had not loaded compleytle or?

  • After Hard Reset My Social Network is not working....

    Due to Some problem I did Hard Reset to my C7 but now My Social network is not working.
    I had reinstall the nokia software but still its not working properly.
    In the Social network all the graphics are coming like picture with a cross.

    Something is wrong because a hard reset will never leave the TC with green LED.
    What version TC.. what firmware??
    What OS on the computer?

  • File- Print not working from SQL Developer 1.2.1 Build MAIN-32.13

    File->Print not working from SQL Developer 1.2.1 Build MAIN-32.13.
    I downloaded sqldeveloper-1.2.1.3213.ZIP and extract to a local directory. From the extracted directory I ran ..\sqldeveloper\sqldeveloper.exe from Windows XP sp2. The program itself seems to run just fine but File-Print doesn't do anything. In Help-About, Java Platform is reported as 1.5.0_06 and Oracle IDE is 1.2.1.3213. I'm not sure where to look for what is causing the problem.
    Thanks

    I hadn't tried CTRL-P before but I did today. On the first attempt, I saw a small jump in the memory usage for sqldeveloper.exe as reported in Windows Task Manager. Otherwise, there was no change. A second CTRL-P in the same session produced a further bump but subsequent attempts in the same session produced no further change in CPU or Memory Usage.
    Using Task Manager to monitor this further, I tried File->Print again and saw that sqldeveloper would periodically climb to 1 or 2 percent CPU and consume a little more memory. After a minute or so, though, all activity stops again.
    I do not get a print dialog box from SQLDeveloper using either CTRL-P or File->Print

  • How to get Network Printing to work with Brother!!

    So i have my BROTHER DCP-7020 printer connected to my Windows machine and i've been sharing the printer on the network with my old iMac 24' which prints perfectly. Now i have the 27' imac and i have no idea why it won't do printing via network, plugging in USB works fine, i've installed the driver but it doesn't look like it did anything. It just worked on my 24' without any hassle, it gets detected in the "Printer Settings" automatically and i dont recall doing anything to get it to work before.
    Can anyone give me some tips of why it won't print and what I need to do in order to get network printing to work on my new Mac?
    By the way BOTH MACHINE runs SNOW LEOPARD.
    Thanks in advance.

    Here's the troubleshoot: http://support.apple.com/kb/HT1404
    And here is the manual method: http://support.apple.com/kb/HT3049
    Hope this helps!

  • My network is not working i am in ghana and i use MTN  network but it is not working why is it like that

    my network is not working i am in ghana and i use MTN  network but it is not working why is it like that... pls get back to me now

    It sounds as if you need to call your mobile carrier.

Maybe you are looking for