Network Problem After Creating Database

Hi,
We install Oracle 11g on Windows 2008 server. Everything is working fine till the installation of Oracle software. After creating the database when we restart server the network cable shows a unplug for 20 miniutes.
If we disable all the Oracle service than everything goes fine.
Please Suggest.
Thanks and Regards
Sarfaraz Zomberkar

This is an interesting problem. Please provide a little more information.
* When you state Oracle 11g, exactly which release version: 11.1.0.6, 11.1.0.7, 11.2.0.1, or 11.2.0.2 - did you install the 32 bit Database software or the 64 bit Database software?
* Which options were selected during the installation, and did you tell the installer to create a database during the installation?
* Exactly which Windows 2008 server version: R1 or R2 - and is the operating system 32 bit or 64 bit?
* How much memory is in the Windows server?
* How many network cables are connected between the server and a network switch(es) - you will probably need to look at the back of the server to determine this answer?
* What are the exact names of the Oracle services that you had to shut down - most likely, the Startup Type of those services are set to "Automatic"
* Have the appropriate network person take a look at the log of errors on the network switch that is connected to the server - there is a chance that the network switch sensed a problem, such as excessive transmission errors, and shut down the network port to prevent a broadcast storm or a similar problem.
* Have the appropriate person check the Windows event logs. Do those logs identify the reason why the network port went down?
Charles Hooper
Co-author of "Expert Oracle Practices: Oracle Database Administration from the Oak Table"
http://hoopercharles.wordpress.com/
IT Manager/Oracle DBA
K&M Machine-Fabricating, Inc.

Similar Messages

Networking problem after a zone is created and installed

Hi all,
I've got a networking problem after a zone was created and installed on a Solaris 10 box. The box was configured with two NICs, one (e1000g0) with a public IP address, the other one (e1000g1) with a private IP address and connected to a local switch. All worked fine so far.
Then I created a local zone with shared networking (e1000g1). The zone has a private IP address which is in the same subnet as e1000g1 on the global zone. After some time, I noticed that I could not access (ssh, ping) the global zone. Then after some time, the global zone became available. The problem happened quite frequently.
Also I observed that: 1) When the global zone was unavailable from outside, it was available (ssh, ping) from another box within the same subnet (e1000g0); 2) If I shutdown e1000g1, the problem was gone.
Any idea what caused this problem?
Many thanks,
Xiaobo

It was a route problem.

Problem when creating Database (Database, OS and hardware Configuraiton included)

Problem when creating Database:
Below are the problems, which I faced during creation of database. I have mentioned both the problem separately. Plus the log file maintained by Oracle during installation. It might help in diagnosing the error. Plus a little conclusion with I turned up to.
There are two problems, when creating database with Oracle Database Assistant. One when creating pre tuned database from CD. And second when creating customized database giving options your self.
Problem # 1:
When creating pre tuned database from CD. The process of creating Database is 90 % complete and is at step # 3 Initializing Database. It gives error ORA-03113: end-of-file on communication channel.
I searched following oracle help for this problem.
ORA-03113: end-of-file on communication channel
Cause: An unexpected end-of-file was processed on the communication channel. The problem could not be handled by the Net8, two-task software. This message could occur if the shadow two-task process associated with a Net8 connect has terminated abnormally, or if there is a physical failure of the interprocess communication vehicle, that is, the network or server machine went down.
Action: If this message occurs during a connection attempt, check the setup files for the appropriate Net8 driver and confirm Net8 software is correctly installed on the server. If the message occurs after a connection is well established, and the error is not due to a physical failure, check if a trace file was generated on the server at failure time. Existence of a trace file may suggest an Oracle internal error that requires the assistance of customer support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Problem # 2:
When creating database with custom option. The process of creating Database is 2 % complete and is at step # 2 Creating Database Files. It gives error ORA-12571: TNS:packet writer failure.
I searched following oracle help for this problem.
ORA-12571: TNS:packet writer failure
Cause: An error occurred during a data send.
Action: Not normally visible to the user. For further details, turn on tracing and re-execute the operation. If error persists, contact Worldwide Customer Support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Log File Showing Error :
Result code for launching of configuration tool is 0
Launched configuration tool Oracle Database Configuration Assistant
Command which is being spawned is C:\Program Files\Oracle\jre\1.1.7\bin/jrew.exe -Duser.dir=d:\oracle\ora81\assistants\dbca\jlib -classpath ";C:\Program Files\Oracle\jre\1.1.7\lib\rt.jar;C:\Program Files\Oracle\jre\1.1.7\lib\i18n.jar;d:\oracle\ora81\jlib\ewt-3_3_6.jar;d:\oracle\ora81\jlib\share-1_0_8.jar;d:\oracle\ora81\jlib\swingall-1_1_1.jar;d:\oracle\ora81\assistants\dbca\jlib\dbassist.jar;d:\oracle\ora81\assistants\jlib\jnls.jar;d:\oracle\ora81\assistants\jlib\acc.jar;d:\oracle\ora81\jlib\help-3_1_8.jar;d:\oracle\ora81\jlib\ice-4_06_6.jar;d:\oracle\ora81\jlib\netcfg.jar;" DBCreateWizard -progress_only -responseFile NO_VALUE -createtype seed -numusers NO_VALUE -apptype NO_VALUE -cartridges NO_VALUE -options NO_VALUE -demos NO_VALUE -seedloc d:\oracle\ora81\starterdb -sid ora8i -orabase d:\oracle -clususer NO_VALUE -cluspswd Protected value, not to be logged -nodeinfo NO_VALUE -gdbName ora8i
Invalid Exit Code. The following result code will be used for configuration tool: 1
Configuration tool Oracle Database Configuration Assistant failed
The datafiles will be copied from the CD to d:\oracle\oradata\ora8i. The Oracle Database Configuration Assistant will begin creating the database.
An Oracle database will be created for you. The database name will be ora8i. The system identifier for the database will be ora8i. The password for the INTERNAL account will be ******, the SYS account will be change_on_install and the SYSTEM account will be manager.
Log File of Installation:
The above code is a part of the log file, which is generated by Oracle installer at C:\Program Files\Oracle\Inventory\Log\..
I just pasted the part of code, highlighted is the code showing error with Oracle Database Configuration Assistant.
Software & Hardware Configuration are as follow:
Software:
Database
Oracle 8.1.7.0.0 (Oracle8i)
Operating System
Microsoft Windows 2000
5.00.2195
Service Pack 2
Hardware:
x86 Family 6 Model 8 stepping
10
AT/AT COMPITABLE
260,400 KB RAM

Dont't worry about that. Before you
create a table(or view), it is wise to
drop the table(or view) with the same name.
If the name doesn't exist, of course there
is an error message. See the following script:
-------------------begin-----------
drop table students cascade constraints;
create table students (
sid varchar2(5),
fname varchar2(20),
lname varchar2(20) not null,
minit char,
primary key (sid));
--------------end-----------------
Good day!
null

Problem when creating Database with Database, OS and hardware Configuraiton

Problem when creating Database:
There are two problems, which I faced during creation of database. When creating database with Oracle Database Assistant. One when creating pre tuned database from CD. And second when creating customized database giving options your self.
Problem # 1:
When creating pre tuned database from CD. The process of creating Database is 90 % complete and is at step # 3 Initializing Database. It gives error ORA-03113: end-of-file on communication channel.
I searched following oracle help for this problem.
ORA-03113: end-of-file on communication channel
Cause: An unexpected end-of-file was processed on the communication channel. The problem could not be handled by the Net8, two-task software. This message could occur if the shadow two-task process associated with a Net8 connect has terminated abnormally, or if there is a physical failure of the interprocess communication vehicle, that is, the network or server machine went down.
Action: If this message occurs during a connection attempt, check the setup files for the appropriate Net8 driver and confirm Net8 software is correctly installed on the server. If the message occurs after a connection is well established, and the error is not due to a physical failure, check if a trace file was generated on the server at failure time. Existence of a trace file may suggest an Oracle internal error that requires the assistance of customer support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Problem # 2:
When creating database with custom option. The process of creating Database is 2 % complete and is at step # 2 Creating Database Files. It gives error ORA-12571: TNS:packet writer failure.
I searched following oracle help for this problem.
ORA-12571: TNS:packet writer failure
Cause: An error occurred during a data send.
Action: Not normally visible to the user. For further details, turn on tracing and re-execute the operation. If error persists, contact Worldwide Customer Support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Software & Hardware Configuration are as follow:
Software:
Database
Oracle 8.1.7.0.0 (Oracle8i)
Operating System
Microsoft Windows 2000
5.00.2195
Service Pack 2
Hardware:
x86 Family 6 Model 8 stepping
10
AT/AT COMPITABLE
260,400 KB RAM

user563502 wrote:
I am working on Solaris 8. What is Alert_SID.log? where can I find it?
ThanksFor the responsible of the upgrade of Oracle database, not even know what Alert log is?
to be honest with you, this is not your work.

Problem when creating Database (Database, OS and hardware Configuraiton)

Problem when creating Database:
There are two problems, which I faced during creation of database. When creating database with Oracle Database Assistant. One when creating pre tuned database from CD. And second when creating customized database giving options your self.
Problem # 1:
When creating pre tuned database from CD. The process of creating Database is 90 % complete and is at step # 3 Initializing Database. It gives error ORA-03113: end-of-file on communication channel.
I searched following oracle help for this problem.
ORA-03113: end-of-file on communication channel
Cause: An unexpected end-of-file was processed on the communication channel. The problem could not be handled by the Net8, two-task software. This message could occur if the shadow two-task process associated with a Net8 connect has terminated abnormally, or if there is a physical failure of the interprocess communication vehicle, that is, the network or server machine went down.
Action: If this message occurs during a connection attempt, check the setup files for the appropriate Net8 driver and confirm Net8 software is correctly installed on the server. If the message occurs after a connection is well established, and the error is not due to a physical failure, check if a trace file was generated on the server at failure time. Existence of a trace file may suggest an Oracle internal error that requires the assistance of customer support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Problem # 2:
When creating database with custom option. The process of creating Database is 2 % complete and is at step # 2 Creating Database Files. It gives error ORA-12571: TNS:packet writer failure.
I searched following oracle help for this problem.
ORA-12571: TNS:packet writer failure
Cause: An error occurred during a data send.
Action: Not normally visible to the user. For further details, turn on tracing and re-execute the operation. If error persists, contact Worldwide Customer Support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Software & Hardware Configuration are as follow:
Software:
Database
Oracle 8.1.7.0.0 (Oracle8i)
Operating System
Microsoft Windows 2000
5.00.2195
Service Pack 2
Hardware:
x86 Family 6 Model 8 stepping
10
AT/AT COMPITABLE
260,400 KB RAM

user563502 wrote:
I am working on Solaris 8. What is Alert_SID.log? where can I find it?
ThanksFor the responsible of the upgrade of Oracle database, not even know what Alert log is?
to be honest with you, this is not your work.

What cause searching network problem after updating iphone 6 from iOS 8.1.2 TO iOS 8.1.3?

what cause searching network problem after updating iphone 6 from iOS 8.1.2 TO iOS 8.1.3?

SSince Apple does not support downgrading the iOS I suggest you start a new question that gives a good title to a specific problem. Then in the body of the thread describe the problem in detail, tell us what steps you have tried so far to correct the problem, what happened, and what error messages you received.

Scripts for run after creating database

HI,
now when 10xe universal installer create database with unicode characterset we are all unabled to run Form6i (forms 6i does not support AL32UTF8) on xe.
I would like to try to create database using EE8MSWIN1250 but I am not sure what scripts I have to run after create database on windows XP professional OS.
Is there any list ?
What else I have to check or run after creating database ?

connect ... as sysdba
@c:\oraclexe\app\oracle\product\10.2.0\server\RDBMS\ADMIN\catalog.sql
@c:\oraclexe\app\oracle\product\10.2.0\server\RDBMS\ADMIN\catblock.sql
@c:\oraclexe\app\oracle\product\10.2.0\server\RDBMS\ADMIN\catproc.sql
@c:\oraclexe\app\oracle\product\10.2.0\server\RDBMS\ADMIN\catoctk.sql
@c:\oraclexe\app\oracle\product\10.2.0\server\RDBMS\ADMIN\owminst.plb
connect system
@c:\oraclexe\app\oracle\product\10.2.0\server\sqlplus\admin\pupbld.sql
@c:\oraclexe\app\oracle\product\10.2.0\server\sqlplus\admin\help\hlpbld.sql helpus.sql
I execute that scripts and it's look like that everything working well except that I can't access Database Home Page.
Any sugestion what I should look for.

Problem in creating database after installion oracle on AIX6.1

Hi.
I have to install oracle 10g on AIX 6.1 silently so i have followed the the below steps:
1. downloaded patch 6613550 and run ./rootpre.sh of that patch as root user
2. created required oracle user and groups ( oracle and dba respectively)
3. installed 10.2.0.1 version by using the following command :
su - oracle -c "/Disk1/runInstaller -ignoreSysPrereqs -silent -responseFile /enterprise.rsp"
4. run oraInventory/orainstRoot.sh
5. run $ORACLE_HOME/root.sh
6. installed oracle 10.2.0.3 patchset using the command :
su - oracle -c "/p10_10203_AIX64-5L/Disk1/runInstaller -ignoreSysPrereqs -silent -force -debug \
FROM_LOCATION="/p10_10203_AIX64-5L/Disk1/stage/products.xml" \
ORACLE_HOME="given $ORACLE_HOME value" \
ORACLE_HOME_NAME="OraDb10g" \
TOPLEVEL_COMPONENT='{"oracle.patchset.db","10.2.0.3.0"}'"2>&1
7. then i am Configuring oracle to startup automatically
8. creating a database using the following command :
su - oracle -c "$ORACLE_HOME/bin/dbca -silent -createDatabase -templateName General_Purpose.dbc -gdbname tc -passwordDialog false -sysPassword sys_password -listeners LISTENER"
but when i execute this command it hangs .. doesn't show any error messages. nothing else..
could any one please help me with that.. where i went wrong..
Note : I have used the same command for creating a database for AIX 5.3 and i worked... but i didn't installed and patchset 6613550 and 10.2.0.3 as 10.2.0.1 is certified with AIX 5.3
please help me .. its urgent

dear friend
thans for replying
in fact i ddi not work
i did the following:
1 CREATE OR REPLACE TRIGGER t_CREATE_SYN
2 AFTER CREATE ON SCHEMA
3 BEGIN
4 DECLARE
5 vCUR INTEGER;
6 vEXE NUMBER;
7 CURSOR TAB_CUR IS
8 SELECT TABLE_NAME FROM USER_TABLES;
9 BEGIN
10 vCUR := DBMS_SQL.OPEN_CURSOR;
11 FOR I IN TAB_CUR LOOP
12 DBMS_SQL.PARSE (vCUR,'CREATE PUBLIC SYNONYM '||' '||I.TABLE_NAME||' '||' FOR '||' '||' '||user||'.'||i.table_name,DBMS_SQL.NATIVE);
13 vEXE := DBMS_SQL.EXECUTE(vCUR);
14 END LOOP;
15 DBMS_SQL.CLOSE_CURSOR(vCUR);
16 END;
17 NULL;
18* END;
SQL> /
Trigger created.
SQL> CREATE TABLE TAR_TAB ( ID NUMBER);
CREATE TABLE TAR_TAB ( ID NUMBER)
ERROR at line 1:
ORA-00604: error occurred at recursive SQL level 1
ORA-30511: invalid DDL operation in system triggers
ORA-06512: at "SYS.DBMS_SYS_SQL", line 824
ORA-06512: at "SYS.DBMS_SQL", line 32
ORA-06512: at line 10
i woder is it possible to write a DDL command in database trigger?
and how can i achive my task

Problem when creating Database:

There are two problems, which I faced during creation of database. When creating database with Oracle Database Assistant. One when creating pre tuned database from CD. And second when creating customized database giving options your self.
Problem # 1:
When creating pre tuned database from CD. The process of creating Database is 90 % complete and is at step # 3 Initializing Database. It gives error ORA-03113: end-of-file on communication channel.
I searched following oracle help for this problem.
ORA-03113: end-of-file on communication channel
Cause: An unexpected end-of-file was processed on the communication channel. The problem could not be handled by the Net8, two-task software. This message could occur if the shadow two-task process associated with a Net8 connect has terminated abnormally, or if there is a physical failure of the interprocess communication vehicle, that is, the network or server machine went down.
Action: If this message occurs during a connection attempt, check the setup files for the appropriate Net8 driver and confirm Net8 software is correctly installed on the server. If the message occurs after a connection is well established, and the error is not due to a physical failure, check if a trace file was generated on the server at failure time. Existence of a trace file may suggest an Oracle internal error that requires the assistance of customer support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.
Problem # 2:
When creating database with custom option. The process of creating Database is 2 % complete and is at step # 2 Creating Database Files. It gives error ORA-12571: TNS:packet writer failure.
I searched following oracle help for this problem.
ORA-12571: TNS:packet writer failure
Cause: An error occurred during a data send.
Action: Not normally visible to the user. For further details, turn on tracing and re-execute the operation. If error persists, contact Worldwide Customer Support.
Conclusion:
What I conceive from this problem and the help available is that, I have to install NET8 again. But I am not sure about the solution, please tell me whether I am rite or not.

user563502 wrote:
I am working on Solaris 8. What is Alert_SID.log? where can I find it?
ThanksFor the responsible of the upgrade of Oracle database, not even know what Alert log is?
to be honest with you, this is not your work.

DSO activation problem after creating the secondary indexes

Hi,
I am facing the problem with DSO activation after creating the secondary indexes.
Compared with Info Cubes there is no functionality available which allows dropping and recreating a secondary index before/after the data activation.
As a workaround I can write a simple report which drops and creates the indexes on database level.
By using a process chain, we can simply insert the drop index report before data activation and the create index report after the data activation process.
Can any body help me step by step procedure or Material to write the programs for delete index and create index reports on DSO object?..
Thanks in advance for your help.
Thanks & Regards,
Bala

hi,
in BI if you are using the dso for reporting then you can simply chk the settings of dso for SID generation.
no need to create the indexes or delete it.
if the dso is not used for report then no need to use indexes.
Ramesh

Problem while Creating Database in 10g

Its very urgent.. Please Help..!!
After installing 10g (Standard Edition) on Windows 2000 Server, I started creating database through Database Configuration Assistant.
Instead of Oracle Home path, different path is specified for Database files.
In 'Step 11 of 12' of the 'Database Configuration Assistant' I specified the 4 new table spaces to create with respective memory sizes.
In 'Step 12' I selected 'Create a Database' and clicked 'Finish' button.
After 7% of the Database creation progress bar, it is giving the following error:
"ORA: 01092 ORACLE instance terminated. Disconnection forced"
And asking for Abort..
What could be the problem. Is it problem with installation or any other services to be started.
After 10g installation I restarted my system.
If required I'll provide some more information.
Its very urgent...
Thanks & Regards

hi satish,
this is not the right forum for database questions. please use the following (database) forums:
http://forums.oracle.com/forums/index.jsp?cat=18
regards,
christian

Oracle 8iEE problem in creating database

When installing Oracle 8i Enterprise Edition for Linux slakware there is a problem of creating the database . while installing if we choose the option of creating the database it hangs at that point .
Although if we skip the creation of the database it shows that the installation is complete . later when we use dbassist it hangs after displaying few file names last one being for CreateWizardMain.
we tried using response files, silent mode also but the computer hangs at that point.
We tried svrmgrl but in that it is displaying an error message for cannot open parameter file with the name that was provided in response file .
Any Suggestions?

I spend 2 days on resolving this problem.
You should make two links:
ln -s /bin/free /usr/bin/free
ln -s /usr/bin/awk /bin/awk
because dbassist looking for this programs.
This is help me, and i think this help you.
greet.
Roman

Problem in create database use dbca in RAC

i setup a two-nodes RAC, and use dbca to create db
here is the output of dbca
[oracle@rac1 ~]$ dbca -silent -responseFile /home/oracle/dbca.rsp
Copying database files
1% complete
3% complete
9% complete
15% complete
21% complete
27% complete
30% complete
Creating and starting Oracle instance
32% complete
36% complete
40% complete
44% complete
45% complete
48% complete
50% complete
Creating cluster database views
52% complete
70% complete
Completing Database Creation
73% complete
76% complete
79% complete
80% complete
81% complete
90% complete
99% complete
100% complete
Look at the log file "/opt/ora/product/10.2.0/db_1/cfgtoollogs/dbca/mydb/mydb.log" for further details.
and here is the log output:
Failed to retrieve network listener resources required for the Real Application Clusters high
availability extensions configurations on the following nodes: [rac1, rac2].
Do you want listeners on port 1521 with prefix LISTENER to be created on nodes [rac1, rac2]
automatically? If you would like to configure the listener with different properties, run NetCA
before continuing.
PRKS-1009 : Failed to start ASM instance "+ASM1" on node "rac1", [CRS-0215: Could not start
resource 'ora.rac1.ASM1.asm'.]
PRKS-1009 : Failed to start ASM instance "+ASM2" on node "rac2", [CRS-0215: Could not start
resource 'ora.rac2.ASM2.asm'.]
Could not mount the diskgroup on node: rac2. The ASM instance on node rac2 is not started.
Could not mount the diskgroup on node: rac2. The ASM instance on node rac2 is not started.
Copying database files
DBCA_PROGRESS : 1%
DBCA_PROGRESS : 3%
DBCA_PROGRESS : 9%
DBCA_PROGRESS : 15%
DBCA_PROGRESS : 21%
DBCA_PROGRESS : 27%
DBCA_PROGRESS : 30%
Creating and starting Oracle instance
DBCA_PROGRESS : 32%
DBCA_PROGRESS : 36%
DBCA_PROGRESS : 40%
DBCA_PROGRESS : 44%
DBCA_PROGRESS : 45%
DBCA_PROGRESS : 48%
DBCA_PROGRESS : 50%
Creating cluster database views
DBCA_PROGRESS : 52%
DBCA_PROGRESS : 70%
Completing Database Creation
Failed to start listeners on nodes "[rac1, rac2]" of cluster database "mydb", "CRS-1028: Dependency
analysis failed because of:
CRS-0223: Resource 'ora.rac2.LISTENER_RAC2.lsnr' has placement error.".
DBCA_PROGRESS : 73%
DBCA_PROGRESS : 76%
DBCA_PROGRESS : 79%
ORA-01078: failure in processing system parameters
ORA-01078: failure in processing system parameters
ORA-01565: error in identifying file '+ORADG/mydb/spfilemydb.ora'
ORA-17503: ksfdopn:2 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-15056: additional error message
ORA-17503: ksfdopn:DGOpenFile05 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-17503: ksfdopn:2 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-15173: entry 'spfilemydb.ora' does not exist in directory 'mydb'
ORA-06512: at line 4
ORA-01034: ORACLE not available
DBCA_PROGRESS : 80%
ORA-01034: ORACLE not available
ORA-01034: ORACLE not available
ORA-01034: ORACLE not available
DBCA_PROGRESS : 81%
ORA-01034: ORACLE not available
DBCA_PROGRESS : 90%
Enterprise manager configuration failed due to the following error -
Invalid username/password.
Refer to the log file at /opt/ora/product/10.2.0/db_1/cfgtoollogs/dbca/mydb/emConfig.log for more
details.
You can retry configuring this database with Enterprise Manager later by manually running
/opt/ora/product/10.2.0/db_1/bin/emca script.
DBCA_PROGRESS : 99%
ORA-01034: ORACLE not available
ORA-27101: shared memory realm does not exist
PRKP-1001 : Error starting instance mydb1 on node rac1
CRS-1028: Dependency analysis failed because of:
CRS-0223: Resource 'ora.mydb.mydb1.inst' has placement error.
PRKP-1001 : Error starting instance mydb2 on node rac2
CRS-1028: Dependency analysis failed because of:
CRS-0223: Resource 'ora.mydb.mydb2.inst' has placement error.
DBCA_PROGRESS : 100%
Database creation complete. Check the logfiles at
/opt/ora/product/10.2.0/db_1/cfgtoollogs/dbca/mydb for details.
Database Information:
Global Database Name:mydb
System Identifier(SID) Prefix:mydb
it should be run netca　before running dbca?

this time i run netca first,and then run dbca to configure the ASM,after that i run dbca to create database
listener and asm instance is online,but when i create DB ,still have error
Copying database files
DBCA_PROGRESS : 1%
DBCA_PROGRESS : 3%
DBCA_PROGRESS : 9%
DBCA_PROGRESS : 15%
DBCA_PROGRESS : 21%
DBCA_PROGRESS : 27%
DBCA_PROGRESS : 30%
Creating and starting Oracle instance
DBCA_PROGRESS : 32%
DBCA_PROGRESS : 36%
DBCA_PROGRESS : 40%
DBCA_PROGRESS : 44%
DBCA_PROGRESS : 45%
DBCA_PROGRESS : 48%
DBCA_PROGRESS : 50%
Creating cluster database views
DBCA_PROGRESS : 52%
DBCA_PROGRESS : 70%
Completing Database Creation
DBCA_PROGRESS : 73%
DBCA_PROGRESS : 76%
DBCA_PROGRESS : 79%
ORA-01078: failure in processing system parameters
ORA-01078: failure in processing system parameters
ORA-01565: error in identifying file '+ORADG/mydb/spfilemydb.ora'
ORA-17503: ksfdopn:2 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-15056: additional error message
ORA-17503: ksfdopn:DGOpenFile05 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-17503: ksfdopn:2 Failed to open file +ORADG/mydb/spfilemydb.ora
ORA-15173: entry 'spfilemydb.ora' does not exist in directory 'mydb'
ORA-06512: at line 4
ORA-01034: ORACLE not available
DBCA_PROGRESS : 80%
ORA-01034: ORACLE not available
ORA-01034: ORACLE not available
DBCA_PROGRESS : 89%
DBCA_PROGRESS : 98%
ORA-01034: ORACLE not available
ORA-27101: shared memory realm does not exist
PRKP-1001 : Error starting instance mydb1 on node rac1
CRS-0215: Could not start resource 'ora.mydb.mydb1.inst'.
PRKP-1001 : Error starting instance mydb2 on node rac2
CRS-0215: Could not start resource 'ora.mydb.mydb2.inst'.
DBCA_PROGRESS : 100%
following info from my template file
<MiscParams>
<databaseType>MULTIPURPOSE</databaseType>
<maxUserConn>20</maxUserConn>
<percentageMemTOSGA>40</percentageMemTOSGA>
<customSGA>false</customSGA>
<archiveLogMode>false</archiveLogMode>
<initParamFileName>+ORADG/admin/{DB_UNIQUE_NAME}/pfile/init.ora</initParamFileName>
</MiscParams>
<SPfile useSPFile="true">{ORACLE_HOME}/dbs/spfile{SID}.ora</SPfile>
</InitParamAttributes>
and dbca create +ORADG in /home/oracle dir (why??)
[oracle@rac1 ~]$ ls +ORADG/admin/mydb/pfile/init.ora.6132011173958
+ORADG/admin/mydb/pfile/init.ora.6132011173958
Edited by: 859340 on 2011-7-12 下午7:25

Unable to access table even after creating Database link

Hi
I have created a data base link.It was created properly.
The Syantax that I have used is follows:
create database link X_link connect to User1 identified by User1 using 'Other_Database'
And on running the query:
select count(*) from table1@X_link
I am getting the error as follows:
TNS could not resolve the connect identifier specified... TNS: could not resolve the connect identifier specified.
Please tell me where is the problem?
Thanks in Advance

Your database link does not work because the entry you used does not exist in the tnsnames.ora in the database $ORACLE_HOME.
Login to the database server, set the environment, and try to tnsping the entry you used for the database link, then fix the tnsnames.ora file (probably in $ORACLE_HOME/network/admin)
You can test a database link using :-
select sysdate from dual@link;

Problem to create database with RAC 10g with Oracle Standard Edition

I install CRS (Cluster Ready Services), and then install Oracle 10g database. Also, I install patches 10.1.0.4. When I create database with ASM storage give me a error to create files database.
Any idea?
Thanks
Edu AlcaÃ±iz

You were right.
http://download-uk.oracle.com/docs/html/B14203_05/intro.htm#sthref44
under the section
"1.3 Configuration Tasks for Oracle Clusterware and Oracle Real Application Clusters"
"... If you use RAC on Oracle Database 10g Standard Edition, then you must use ASM."
Thanks, problem solved.
- Vegard

Network Problem After Creating Database

Similar Messages

Maybe you are looking for